 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Technical Data Sheet Chip LED with Right Angle Lens 12-11/BHC-ZL1M2QY/2C Features Package in 8mm tape on 7diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. Mono-color type. Pb-free. ESD Protection. The product itself will remain within RoHS complaint version. Descriptions The 12-11 SMD LED is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. Besides, lightweight makes them ideal for miniature applications. etc. Applications Backlighting in dashboard and switch. Telecommunication: indicator and backlighting in telephone and fax. Flat backlight for LCD, switch and symbol. General use. Device Selection Guide Chip Part No. 12-11/BHC-ZL1M2QY/2C Emitted Color Material InGaN Blue Water Clear Resin Color Everlight Electronics Co., Ltd. Device No. :DSE-0001705 http://www.everlight.com Prepared Date:18-Jun-2009 Rev.2 Page: 1 of 10 Prepared by: Huangyongxin 12-11/BHC-ZL1M2QY/2C Package Outline Dimensions Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No. : DSE-0001705 http://www.everlight.com Prepared date:18-Jun-2009 Rev.2 Page: 2 of 10 Prepared by: Huangyongxin 12-11/BHC-ZL1M2QY/2C Absolute Maximum Ratings (Ta=25) Parameter Reverse Voltage Forward Current Peak Forward Current (Duty 1/10 @1KHz) Power Dissipation Electrostatic Discharge(HBM) Operating Temperature Storage Temperature Soldering Temperature Symbol VR IF IFP Pd ESD Topr Tstg Tsol Rating 5 25 100 95 2000 -40 ~ +85 -40 ~ +90 Unit V mA mA mW V Reflow Soldering : 260 for 10 sec. Hand Soldering : 350 for 3 sec. Electro-Optical Characteristics (Ta=25) Parameter Luminous Intensity Viewing Angle Peak Wavelength Dominant Wavelength Spectrum Radiation Bandwidth Forward Voltage Symbol Iv 21/2 p d VF Min. 11.5 --------465.0 ----2.70 Typ. ----120 468 ----25 ----Max. 28.5 --------475.0 ----3.20 Unit mcd deg nm nm nm V IF =5mA Condition Notes: 1.Tolerance of Luminous Intensity 11% 2.Tolerance of Dominant Wavelength 1nm 3.Tolerance of Forward Voltage 0.05V \ Everlight Electronics Co., Ltd. Device No. : DSE-0001705 http://www.everlight.com Prepared date:18-Jun-2009 Rev.2 Page: 3 of 10 Prepared by: Huangyongxin 12-11/BHC-ZL1M2QY/2C Bin Range Of Luminous Intensity Bin L1 L2 M1 M2 Min 11.5 14.5 18.0 22.5 Max 14.5 18.0 22.5 28.5 mcd IF=5mA Unit Condition Bin Range Of Dom. Wavelength Group Bin X Y Min 465 470 Max 470 475 Unit nm Condition IF =5mA Z Bin Range Of Forward Voltage Group Bin Code 29 30 Q 31 32 Min. 2.70 2.80 2.90 3.10 Max. 2.80 2.90 3.10 3.20 V IF =5mA Unit Condition Notes: 1.Tolerance of Luminous Intensity 11% 2.Tolerance of Dominant Wavelength 1nm 3.Tolerance of Forward Voltage 0.05V Everlight Electronics Co., Ltd. Device No. : DSE-0001705 http://www.everlight.com Prepared date:18-Jun-2009 Rev.2 Page: 4 of 10 Prepared by: Huangyongxin 12-11/BHC-ZL1M2QY/2C Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. Device No. : DSE-0001705 http://www.everlight.com Prepared date:18-Jun-2009 Rev.2 Page: 5 of 10 Prepared by: Huangyongxin 12-11/BHC-ZL1M2QY/2C Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No. : DSE-0001705 http://www.everlight.com Prepared date:18-Jun-2009 Rev.2 Page: 6 of 10 Prepared by: Huangyongxin 12-11/BHC-ZL1M2QY/2C Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Label Everlight Electronics Co., Ltd. Device No. : DSE-0001705 http://www.everlight.com Prepared date:18-Jun-2009 Rev.2 Page: 7 of 10 Prepared by: Huangyongxin 12-11/BHC-ZL1M2QY/2C Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level : 90 % LTPD : 10 % Test Sample Ac/Re No. Items Test Condition Hours/Cycles Size 1 Reflow Soldering Temp. : 2605 Min5sec. H : +100 15min 5 min L : -40 15min H : +100 5min 10 sec L : -10 5min Temp. : 100 Temp. : -40 IF = 20 mA 85/ 85% RH 6 Min. 300 Cycles 22 PCS. 0/1 0/1 2 Temperature Cycle 22 PCS. 3 4 5 6 7 Thermal Shock High Temperature Storage Low Temperature Storage DC Operating Life High Temperature / High Humidity 300 Cycles 1000 Hrs. 1000 Hrs. 1000 Hrs. 1000 Hrs. 22 PCS. 22 PCS. 22 PCS. 22 PCS. 22 PCS. 0/1 0/1 0/1 0/1 0/1 Everlight Electronics Co., Ltd. Device No. : DSE-0001705 http://www.everlight.com Prepared date:18-Jun-2009 Rev.2 Page: 8 of 10 Prepared by: Huangyongxin 12-11/BHC-ZL1M2QY/2C Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30 or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No. : DSE-0001705 http://www.everlight.com Prepared date:18-Jun-2009 Rev.2 Page: 9 of 10 Prepared by: Huangyongxin 12-11/BHC-ZL1M2QY/2C 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. Device No. : DSE-0001705 http://www.everlight.com Prepared date:18-Jun-2009 Rev.2 Page: 10 of 10 Prepared by: Huangyongxin |
Price & Availability of 12-11-BHC-ZL1M2QY-2C
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |