 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Preliminary Data Sheet VS-550 Dual Frequency VCSO Features * Industry Standard Package, 9 x 14 x 3.5 mm * Output Frequencies from 500 MHz to 850 MHz * 3.3 V Operation * Low Jitter < 0.35 ps-rms across 50 kHz to 80 MHz * LV-PECL Logic Levels with Fast Transition Times * Complementary Outputs * Frequency Select Feature Applications PLL circuits for Clock Smoothing and Frequency Translation Description * 10G Fibre Channel * 10GbE LAN / WAN * OC-192 * SONET / SDH Standard INCITS/T11 Project 1413-D IEEE 802.3ae ITU-T G.709 GR-253-CORE Issue3 Vcc COutput Output Description SAW 1 SAW 2 The VS-550 is a SAW based voltage controlled oscillator that operates at the fundamental frequencies of the internal SAW filters. These SAW filters are high-Q quartz devices that enable the circuit to achieve low phase jitter performance over a wide operating temperature range. The dual oscillator is housed in a hermetically sealed J-lead surface mount package offered on tape and reel. It has a frequency select function that enables either "Frequency 1" or "Frequency 2." FS Gnd Vc Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 1 of 7 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 12Sep03 VS-550 Voltage Controlled SAW Oscillator Electrical Performance Parameter Frequency Nominal Frequency Absolute Pull Range Linearity Gain Transfer (See Pg 5) Temperature Stability Transition Time Supply Voltage Current (No Load) Outputs Mid Level Swing Current Rise Time Fall Time Symmetry Spurious Suppression Jitter (See Pg 5) Control Voltage Input Impedance Modulation Bandwidth Operating Temperature Package Size 1. 2. 3. 4. 5. 6. 7. 8. Preliminary Data Sheet Symbol fN APR Lin KV fSTAB Minimum Typical 500 - 850 Maximum Units MHz ppm % ppm/V ppm sec Notes 1,2,3 1,2,3,8 2,4,8 2,8 1,6 6 2,3 3 2,3 2,3 6 5,6 5,6 2,3 6 6,7 6 6 1,3 50 5 +385 100 4 2.97 3.3 55 VCC-1.3 650 250 250 50 60 0.300 100 500 -40 9.0 x 14.0 x 3.5 85 3.63 70 VCC-1.1 800 20 400 400 55 VCC ICC V mA V mV-pp mA ps ps % dBc ps-rms k kHz C mm VCC-1.5 500 IOUT tR tF SYM J Zc BW TOP 45 50 See Standard Frequencies and Ordering Information (Pg 7). Parameters are tested with production test circuit below (Fig 1). Parameters are tested at ambient temperature with test limits guardbanded for specified operating temperature. Measured as the maximum deviation from the best straight-line fit, per MIL-0-55310. Measured from 20% to 80% of a full output swing (Fig 2). Not tested in production, guaranteed by design, verified at qualification. Integrated across 50 kHz to 80 MHz, per GR-253-CORE Issue3. Tested with Vc = 0.3V to 3.0V. (-1.3V to +2V) Freq1, Freq2 (-0.8V, +1.2V) 1 2 3 (-1.3V) 6 5 4 Output 80% Vcc - 1.3V (+2V) COutput tR tF SYM = 100 x tA / tB Vcc - 1.0V 50 50 20% Vcc - 1.6V Test Circuit Notes: 1) To Permit 50 Measurement of Outputs, all DC Inputs are Biased Down 1.3V. 2) All Voltage Sources Contain Bypass Capacitors to Minimize Supply Noise. 3) 50 Terminations are Within Test Equipment. tA tB Figure 1. Test Circuit Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 2 of 7 Figure 2. 100K LV-PECL Waveform Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 12Sep03 VS-550 Voltage Controlled SAW Oscillator Outline Diagram 6 5 4 Preliminary Data Sheet Pad Layout VS-550-LFF-GNN XXX.XXX-XXX.XXX VI YWW 8.890.15 [0.3500.006] ( 7.63 [0.300]) 1.27 [0.050] 1 2 3 13.970.20 [0.5500.008] 0.460.05 [0.0180.002] [ +0.20 3.42-0.30 0.135+0.008 -0.012 ] 3.00 [0.118] 8.80 [0.346] 2.54 [0.100] 5.08 [0.200] mm [inch] 5.080.13 [0.2000.005] 2.540.13 [0.1000.005] mm [inch] Pin Out Pin 1 2 Symbol VC FS Function VCSO Control Voltage Frequency Select Frequency 1 = 0.0 to 0.5 V Frequency 2 = 2.5 to 3.3 V Case and Electrical Ground VCSO Output VCSO Complementary Output Power Supply Voltage (3.3 V 10%) 3 4 5 6 GND Output COutput VCC Tape and Reel (EIA-481-2-A) Po ODo W2 F W D C N A P1 W1 B Tape Dimensions (mm) Dimension Tolerance VS-550 Reel Dimensions (mm) F Typ 11.5 W Typ 24 Do Typ 1.5 Po Typ 4 P1 Typ 12 A Typ 330 B Min 1.5 C Typ 13 D Min 20.2 N Min 100 W1 Typ 24.4 W2 Max 30.4 # Per Reel 200 Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 3 of 7 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 12Sep03 VS-550 Voltage Controlled SAW Oscillator Preliminary Data Sheet Absolute Maximum Ratings Parameter Power Supply Output Current Voltage Control Range Storage Temperature Soldering Temp/Time Symbol VCC Iout VC TS TLS Ratings 0 to 6 25 0 to VCC -55 to 125 220/10 Unit V mA V C C/sec Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this datasheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Suggested Output Load Configurations 0.10 F 0.01 F +3.3V 0.10 F 0.01 F +3.3V +3.3V 150 150 Vc FS Gnd 1 2 3 6 5 4 Vcc COutput Output Z = 50 Z = 50 240 100 Vc FS Gnd 1 2 3 6 5 4 Vcc COutput Z = 50 Output Z = 50 40 40 49 49 240 LV-PECL to LV-PECL: For short transmission lengths, the power consumption could be reduced by removing the 100 resistor and doubling the value of the pull down resistors. LV-PECL to LVDS: Restricted for short transmission lengths. Configuration may require modification depending on LVDS receiver. 0.10 F 0.01 F +3.3V 0.10 F 0.01 F +2.0V Vc FS Gnd 1 2 3 6 5 4 Vcc COutput Output 0.01 F Vc FS -1.3V 1 2 3 6 5 4 Vcc COutput Output 0.01 F 240 240 Functional Test: Allows standard power supply configuration. Since AC coupled, the LV-PECL levels cannot be measured. Production Test: Allows direct DC coupling into 50 measurement equipment. Must bias the power supplies as shown. Similar to Figure 1. Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 4 of 7 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 12Sep03 VS-550 Voltage Controlled SAW Oscillator Typical Characteristics 800 600 400 Preliminary Data Sheet Frequency (PPM) 200 0 -200 -400 -600 -800 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 At Ambient (22.5 C) Typical Gain Transfer @ 622.0800 = +385 ppm/V Typical Gain Transfer @ 669.3266 = +370 ppm/V Control Voltage (V) Typical Calculated Jitter @ 622.0800 MHz SONET OC-48 (12kHz-20MHz) = 0.254 ps-rms; 1.78 ps-pp SONET OC-192 (50kHz-80MHz) = 0.268 ps-rms; 1.88 ps-pp Typical Calculated Jitter @ 669.3266 MHz SONET OC-48 (12kHz-20MHz) = 0.323 ps-rms; 2.26 ps-pp SONET OC-192 (50kHz-80MHz) = 0.308 ps-rms; 2.16 ps-pp Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 5 of 7 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 12Sep03 VS-550 Voltage Controlled SAW Oscillator Preliminary Data Sheet Reliability The VS-550 family is capable of meeting the following qualification tests: Environmental Compliance Parameter Mechanical Shock Mechanical Vibration Solderability Gross and Fine Leak Resistance to Solvents Conditions MIL-STD-883, Method 2002 MIL-STD-883, Method 2007 MIL-STD-883, Method 2003 MIL-STD-883, Method 1014 MIL-STD-883, Method 2016 Handling Precautions Although ESD protection circuitry has been designed into the VS-550 proper precautions should be taken when handling and mounting. VI employs a human body model and a charged-device model (CDM) for ESD susceptibility testing and design protection evaluation. ESD Ratings Model Human Body Model Charged Device Model Minimum 500 500 Conditions MIL-STD 883, Method 3015 JESD 22-C101 Recommended Solder Reflow Profile 220 Temperature (Deg C) 183 150 60 60-90 45-60 Time (s) VI qualification includes aging at various extreme temperatures, shock and vibration, temperature cycling, and IR reflow simulation. The conditions a device can withstand are well understood and devices can be subjected to the profile above. This profile shows a ramp up condition to prevent thermal shock, a preheat period in which the flux is activated, a ramp up to 183C which is the reflow temperature of Sn/Pb eutectic, and a gradual cool down. The time above 183C should not exceed 60 seconds and the peak temperature should be no more than 220C for 10 seconds. The VS-550's are hermetically sealed so an aqueous wash is not an issue. Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 6 of 7 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 12Sep03 VS-550 Voltage Controlled SAW Oscillator Preliminary Data Sheet Standard Frequencies (MHz) Frequency 1 622.0800 P2 666.5143 P5 625.0000 P3 669.3266 R3 644.5313 P4 625.0000 P3 666.5143 P5 690.5692 R4 Frequency 2 644.5313 P4 669.3266 R3 693.4830 R6 657.4219 PB 672.1627 R5 1. Other frequencies available upon request, please contact VI for details. 2. Frequency 1 must be lower than Frequency 2. Not all combinations are available. Ordering Information VS - 550 - L F F - G N N - P2 - R3 Product Family VS: VCSO Frequency 2 (See Above) P3 - R6 Package 550: 9 x 14 x 3.5 mm Frequency 1 (See Above) P2 - R3 Input L: 3.3 V Other (Future Use) N: N/A Output F: LV-PECL Other (Future Use) N: N/A Operating Temperature F: -40 to 85 C Absolute Pull Range G: +/- 50 ppm H: +/- 100 ppm For Additional Information, Please Contact: USA: Vectron International, 267 Lowell Rd, Hudson, NH 03051 . . . . Tel: 1-88-VECTRON-1 Fax: 1-888-FAX-VECTRON EUROPE: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tel: +49 (0) 3328-4784-17 Fax: +49 (0) 3328-4784-30 ASIA: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tel: +86-21-28909740 Fax: +86-21-28909999 Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 7 of 7 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 12Sep03 |
Price & Availability of VS-550
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |