ds-170 rev c saronix saronix voltage controlled crystal oscillator technical data ST1317 / st1517 series 3.3 & 5v, hcmos, smd 141 jefferson drive ? menlo park, ca 94025 usa 650-470-7700 800-227-8974 fax 650-462-9894 www.saronix.com frequency range: 32 mhz to 125 mhz frequency stability: actual size description the ST1317 / 1517 series are voltage controlled crystal oscillators, with output logic levels compatible with hcmos and ttl logic families. the device is contained in a sub-miniature, very low profile, leadless ceramic smd pack- age with 6 gold-plated contact pads. this miniature vcxo is ideal for to- day's automated assembly environments. applications ? for use in phase-locked loop (pll) clock and data recovery, frequency translation, or frequency synthesis applications in video, video compres- sion, telephony, and lan/wan data communication environments. high and wide frequency range from 32 to 125 mhz, see st1307 / 1507 for frequencies from 1 to 31.999 mhz 3.3 or 5 volt operation hcmos and ttl compatible tri-state output standard miniature ceramic smd package available on tape & reel; 16mm tape, 500pcs per reel * apr = (vcxo pull relative to specified output frequency) - (vcxo frequency stability) output waveform t r t f hcmos symmetry 1 level 80% v dd 50% v dd 20% v dd 0 level input impedance (pin 1): frequency response (-3db): pullability: rated control voltage: operable control voltage: transfer function: monotonic linearity: center control voltage: 50k ? min 50 khz min 32, 50, 80, 100 ppm apr* (over rated control voltage) 0.5 to 4.5v (5v supply), 0.3 to 3.0v (3.3v supply) (-0.5v) to (v dd +0.5v) frequency increases when control voltage increases 10% max 2.5v (5v supply), 1.65v (3.3v supply) shock: solderability: terminal strength: vibration: solvent resistance: resistance to soldering heat: mechanical: mil-std-883, method 2002, condition b mil-std-883, method 2003 mil-std-883, method 2004, condition d mil-std-883, method 2007, condition a mil-std-202, method 215 mil-std-202, method 210, condition i or j mil-std-883, method 1011, condition a mil-std-883, method 1004 environmental: 10 sec max 50 ppm over all conditions: operating temperature, rated input (supply) voltage changes, load change, calibration tolerance, shock and vibration (with control voltage held at center value) temperature range: operating: storage: 0 to +70c or -40 to +85c -55 to +125c supply voltage: recommended operating: 3.3v 10% or 5v 5% supply current: 35ma max (3.3v) 50ma max (32 to 70mhz), 65ma max (70+ to 125mhz) (5v) output drive: symmetry: rise & fall times: logic 0: logic 1: load: period jitter rms: phase noise: 5v: 45/55% @ 50% v dd, 40/60% @ 1.4v level 3.3v: 45/55% @50% v dd (0 to +70c), 40/60% (-40 to +85c) 4ns max, 20 to 80% v dd (3.3v cmos and 5v acmos) 1.5ns max, 0.5v to 2.5v (5v ttl) 5v: 20% v dd max for acmos or 0.5v max for ttl 3.3v: 10% v dd max for capacitive load, 20% v dd max for 95 ? ac 5v: 80% v dd min for acmos or 2.5v min for ttl 3.3v: 90% v dd min for capacitive load, 80% v dd min for 95 ? ac 5v: 5ttl or 50 ? ac or 50pf 32 to 50mhz, 30pf 50+ to 125mhz 3.3v: 30pf 32 to 80mhz, 95 ? ac 80+ to 125mhz 20ps max -95dbc / hz @100hz, -110dbc / hz @1khz, -100dbc / hz @10khz pull characteristics: solder reflow guide reflow 240c max 4c/sec max preheat 183 10c cooling 1 ? 2 minutes time 4c/sec max 150 200 250 temperature ? c aging: 12ppm max for 10 years @ +40c average ambient op. temp. thermal shock: moisture resistance: total vcxo pull from specified nominal output frequency under all operating conditions for the life of the unit
ds-170 rev c saronix ST1317 / st1517 series saronix voltage controlled crystal oscillator technical data 3.3 & 5v hcmos, smd 141 jefferson drive ? menlo park, ca 94025 usa 650-470-7700 800-227-8974 fax 650-462-9894 www.saronix.com tri-state logic table required input levels on pin 2: logic 1 = 3.0v min logic 0 = 0.5v max(5v), 0.3v max (3.3v) pin 4 output oscillation high impedance package details recommended land pattern part numbering guide power supply ma m v c 0.1f oscillator pin 1 pin 2 pin 3 pin 4 pin 5 pin 6 c l = 50pf: 32 to 50 mhz 30pf: 50+ to 125 mhz (note a) tri-state input or enable/disable (current limited on fixture) 5v hcmos (used at saronix) note a: c l includes probe and jig capacitance. model saronix tri-state frequency (mhz) linearity b = 10% series 1517 = 5v, ceramic, hcmos / ttl vcxo 1317 = 3.3v, ceramic, hcmos vcxo pullability (minimum apr) * b = 100 ppm n = 80 ppm a = 50 ppm f = 32 ppm st 1317 b b b - 125.0000 (t) stability tolerance b = 50 ppm 0 to +70c e = 50 ppm -40 to +85c test circuits: test point 780 ? c l = 15pf (note a) oscillator pin 1 pin 2 pin 3 pin 4 pin 5 pin 6 v c 0.1f power supply ma m v cc simulated test load test point tri-state input or enable/disable (current limited on fixture) pin 2 input logic 1 or n/c logic 0 7.2 .284 5.2 .205 2.0 .079 1.4 .055 2.8 .110 1.6 .063 1.2 .047 5.08 .200 2.54 .100 max max max pin functions: pin 1: control voltage pin 2: tri-state control pin 3: gnd pin 4: output pin 5: n/c pin 6: supply voltage pin 1 pin 3 pin 6 pin 4 2.54 .100 1.8 .071 4.4 .173 2.0 .079 2.4 .094 5.08 .200 4 3 1 6 ** scale: none (dimensions in ) mm inches ** external high frequency power supply decoupling required. pin 2 pin 5 all specifications are subject to change without notice. packaging blank = bulk packaged (t) = tape & reel* *full reel increments only (500pcs) 5v ttl (used at saronix) note a: c l includes probe and jig capacitance. marking format (exact location of items may vary) ST1317 xxx yywwx frequency year model denotes pin 1 configuration week country of origin * apr = (vcxo pull relative to specified output frequency) - (vcxo frequency stability) total vcxo pull from specified nominal output frequency under all operating conditions for the life of the unit
|
