1 ? fn3735.2 caution: these devices are sensitive to electrostatic discharge; follow proper ic handling procedures. 1-888-intersil or 321-724-7143 | intersil (and design) is a registered trademark of intersil americas inc. copyright ? intersil americas inc. 2002. all rights reserved all other trademarks mentioned are the property of their respective owners. ha-2520/883 uncompensated, high slew rate operational amplifier the ha-2520/883 is a monolithic operational amplifier which delivers an unsurpassed combination of specifications for slew rate, bandwidth and settling time. this dielectrically isolated amplifier is designed for closed loop gains of 3 or greater without external compensation. in addition, this high performance component also provides low offset current and high input impedance. the 100v/ s (min) slew rate and fast settling time of this amplifier make it ideal for pulse amplification and data acquisition designs. to insure compliance with slew rate and transient response specifications, the device is 100% tested for ac performance characteristics over full temperature. this device is a valuable component for rf and video circuitry requiring wideband operation. for accurate signal conditioning designs, the ha-2520/883?s superior dynamic specifications are complemented by 25na (max) offset current and offset voltage adjust capability. applications ? data acquisition systems ? rf amplifiers ? video amplifiers ? signal generators ? pulse amplification features ? this circuit is processed in accordance to mil-std-883 and is fully conformant under the provisions of paragraph 1.2.1. ? high slew rate . . . . . . . . . . . . . . . . . . . . . .100v/ s (min) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120v/ s (min) ? wide power bandwidth . . . . . . . . . . . . . . . . 1.5mhz (min) ? wide gain bandwidth. . . . . . . . . . . . . . . . . . .10mhz (min) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mhz (typ) ? high input impedance . . . . . . . . . . . . . . . . . . 50m ? (min) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100m ? (typ) ? low offset current . . . . . . . . . . . . . . . . . . . . . . 25na (min) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10na (typ) ? fast settling (0.1% of 10v step) . . . . . . . . . . 200ns (typ) ? low quiescent supply current . . . . . . . . . . . . 6ma (max) pinout ha-2520/883 (metal can) top view ordering information part number temp. range ( o c) package pkg. no. ha2-2520/883 -55 o c to +125 o c 8 pin can t8.c 2 4 6 1 3 7 5 8 comp out -in v- bal +in v+ bal + - data sheet october 2002
2 absolute maximum ratings thermal information voltage between v+ and v- terminals . . . . . . . . . . . . . . . . . . . .40v differential input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15v voltage at either input terminal . . . . . . . . . . . . . . . . . . . . . v+ to v- peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50ma junction temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+175 o c storage temperature range . . . . . . . . . . . . . . . . . -65 o c to +150 o c esd rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .<2000v lead temperature (soldering 10s) . . . . . . . . . . . . . . . . . . . .+300 o c thermal resistance ja jc metal can package . . . . . . . . . . . . . . . . . 160 o c/w 75 o c/w package power dissipation limit at +75 o c for t j +175 o c metal can package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625mw package power dissipation derating factor above +75 o c metal can package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3mw/ o c caution: stresses above those listed in ?absolute maximum ratings? may cause permanent damage to the device. this is a stress o nly rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. note: 1. ja is measured with the component mounted on a low effective thermal conductivity test board in free air. see tech brief tb379 for details. operating conditions operating temperature range . . . . . . . . . . . . . . . -55 o c to +125 o c operating supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15v v incm 1/2 (v+ - v-) r l 2k ? table 1. dc electrical performance characteristics device tested at: v supply = 15v, r source = 100 ? , r load = 500k ? , v out = 0v, unless otherwise specified. parameters symbol conditions group a subgroups temperature ha-2520/883 units min max input offset voltage v io v cm = 0v 1 +25 o c-88mv 2, 3 +125 o c, -55 o c -10 10 mv input bias current +i b v cm = 0v, +r s = 100k ? , -r s = 100 ? 1+25 o c -200 200 na 2, 3 +125 o c, -55 o c -400 400 na -i b v cm = 0v, +r s = 100 ? , -r s = 100k ? 1+25 o c -200 200 na 2, 3 +125 o c, -55 o c -400 400 na input offset current i io v cm = 0v, +r s = 100k ? , -r s = 100k ? 1+25 o c -25 25 na 2, 3 +125 o c, -55 o c -50 50 na common mode range +cmr v+ = 5v, v- = -25v 1 +25 o c+10-v 2, 3 +125 o c, -55 o c+10 - v -cmr v+ = 25v, v- = -5v 1 +25 o c--10v 2, 3 +125 o c, -55 o c--10v large signal voltage gain +a vol v out = 0v and +10v, r l = 2k ? 4+25 o c10-kv/v 5, 6 +125 o c, -55 o c7.5 - kv/v -a vol v out = 0v and -10v, r l = 2k ? 4+25 o c10-kv/v 5, 6 +125 o c, -55 o c7.5 - kv/v common mode rejection ratio +cmrr ? v cm = +10v, v+ = +5v, v- = -25v, v out = -10v 1+25 o c80-db 2, 3 +125 o c, -55 o c80 - db -cmrr ? v cm = -10v, v+ = +25v, v- = -5v, v out = +10v 1+25 o c80-db 2, 3 +125 o c, -55 o c80 - db output voltage swing +v out r l = 2k ? 4+25 o c10-v 5, 6 +125 o c, -55 o c10 - v -v out r l = 2k ? 4+25 o c--10v 5, 6 +125 o c, -55 o c--10v ha-2520/883
3 output current +i out v out = -10v 4 +25 o c10-ma 5, 6 +125 o c, -55 o c7.5 - ma -i out v out = +10v 4 +25 o c--10ma 5, 6 +125 o c, -55 o c--7.5ma quiescent power supply current +i cc v out = 0v, i out = 0ma 1 +25 o c-6ma 2, 3 +125 o c, -55 o c-6.5ma -i cc v out = 0v, i out = 0ma 1 +25 o c-6-ma 2, 3 +125 o c, -55 o c-6.5 - ma power supply rejection ratio +psrr ? v sup = 10v, v+ = +20v, v- = -15v, v+ = +10v, v- = -15v 1+25 o c80-db 2, 3 +125 o c, -55 o c80 - db -psrr ? v sup = 10v, v+ = +15v, v- = -20v, v+ = +15v, v- = -10v 1+25 o c80-db 2, 3 +125 o c, -55 o c80 - db offset voltage adjustment +v io adj note 1 1 +25 o cv io -1 - mv 2, 3 +125 o c, -55 o cv io -1 - mv -v io adj note 1 1 +25 o cv io +1 - mv 2, 3 +125 o c, -55 o cv io +1 - mv note: 2. offset adjustment range is [v io (measured) 1mv] minimum referred to output. this test is for functionality only to assure adjustment through 0v. table 2. ac electrical performance characteristics device tested at: v supply = 15v, r source = 50 ? , r load = 2k ? , c load = 50pf, a vcl = +3v/v, unless otherwise specified. parameters symbol conditions group a subgroups temperature ha-2520/883 units min max slew rate +sr v out = -5v to +5v, 25% +sr 75% 7 +25 o c 100 - v/ s 8a, 8b +125 o c, -55 o c84 - v/ s -sr v out = +5v to -5v, 75% -sr 25% 7 +25 o c 100 - v/ s 8a, 8b +125 o c, -55 o c84 - v/ s rise and fall time t r v out = 0 to +200mv, 10% t r 90% 7 +25 o c-50ns 8a, 8b +125 o c, -55 o c-55ns t f v out = 0 to -200mv, 10% t f 90% 7 +25 o c-50ns 8a, 8b +125 o c, -55 o c-55ns overshoot +os v out = 0 to +200mv 7 +25 o c-40% 8a, 8b +125 o c, -55 o c-45% -os v out = 0 to -200mv 7 +25 o c-40% 8a, 8b +125 o c, -55 o c-45% table 1. dc electrical performance characteristics (continued) device tested at: v supply = 15v, r source = 100 ? , r load = 500k ? , v out = 0v, unless otherwise specified. parameters symbol conditions group a subgroups temperature ha-2520/883 units min max ha-2520/883
4 table 3. electrical performance characteristics device characterized at: v supply = 15v, r load = 2k ? , c load = 50pf, a v 3, c comp = 0pf, unless otherwise specified. parameters symbol conditions notes temperature ha-2520/883 units min max differential input resistance r in v cm = 0v 1 +25 o c50-m ? full power bandwidth gbwp v o = 200mv, f o = 10khz 1 +25 o c10-mhz v o = 200mv, f o = 1mhz 1 +25 o c10-mhz full power bandwidth fpbw v peak = 10v 1, 2 +25 o c1.6-mhz minimum closed loop stable gain clsg r l = 2k ? , c l = 50pf 1 -55 o c to +125 o c+3 - v/v quiescent power consumption pc v out = 0v, i out = 0ma 1, 3 -55 o c to +125 o c- 195mw notes: 3. parameters listed in table 3 are controlled via design or proc ess parameters and are not directly tested at final production. these parameters are lab characterized upon initial design release, or upon desig n changes. these param eters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation. 4. full power bandwidth guarantee based on slew rate measurement using fpbw = slew rate/(2 v peak ). 5. quiescent power consumption based upon quiescent supply current test maximum. (no load on outputs.) table 4. electrical test requirements mil-std-883 test requirements subgroups (see tables 1 and 2) interim electrical parameters (pre burn-in) 1 final electrical test parameters 1 (note 4), 2, 3, 4, 5, 6, 7, 8a, 8b group a test requirements 1, 2, 3, 4, 5, 6, 7, 8a, 8b groups c and d endpoints 1 note: 6. pda applies to subgroup 1 only. ha-2520/883
5 die characteristics die dimensions: 67 x 57 x 19 mils 1 mils 1700 x 1440 x 483 m 25.4 m metallization: type: al, 1% cu thickness: 16k ? 2k ? glassivation: type: nitride (si3n4) over silox (sio2, 5% phos.) silox thickness: 12k? 2k? nitride thickness: 3.5k? 1.5k? worst case current density: 0.26 x 10 5 a/cm 2 substrate potential (powered up): unbiased transistor count: ha-2520/883: 40 process: bipolar dielectric isolation metallization mask layout comp v+ out bal bal -in +in v- ha-2520/883
6 all intersil u.s. products are manufactured, assembled and tested utilizing iso9000 quality systems. intersil corporation?s quality certifications can be viewed at www.intersil.com/design/quality intersil products are sold by description only. intersil corporation reserves the right to make changes in circuit design, soft ware and/or specifications at any time without notice. accordingly, the reader is cautioned to verify that data sheets are current before placing orders. information furnishe d by intersil is believed to be accurate and reliable. however, no responsibility is assumed by intersil or its subsidiaries for its use; nor for any infringements of paten ts or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of intersil or its subsidiari es. for information regarding intersil corporation and its products, see www.intersil.com ha-2520/883 metal can packages (can) notes: 1. (all leads) ?b applies between l1 and l2. ?b1 applies between l2 and 0.500 from the reference plane. diameter is uncontrolled in l1 and beyond 0.500 from the reference plane. 2. measured from maximum diameter of the product. 3. is the basic spacing from the ce nterline of the tab to terminal 1 and is the basic spacing of each lead or lead position (n -1 places) from , looking at the bottom of the package. 4. n is the maximum number of terminal positions. 5. dimensioning and toleranci ng per ansi y14.5m - 1982. 6. controlling dimension: inch. ?b ?d2 ? e k1 k ?b1 base and seating plane f q ?d ?d1 l1 l2 reference plane l a ?b2 ?b1 base metal lead finish section a-a a a n e 1 c l 2 1 t8.c mil-std-1835 macy1-x8 (a1) 8 lead metal can package symbol inches millimeters notes min max min max a 0.165 0.185 4.19 4.70 - ?b 0.016 0.019 0.41 0.48 1 ?b1 0.016 0.021 0.41 0.53 1 ?b2 0.016 0.024 0.41 0.61 - ?d 0.335 0.375 8.51 9.40 - ?d1 0.305 0.335 7.75 8.51 - ?d2 0.110 0.160 2.79 4.06 - e 0.200 bsc 5.08 bsc - e1 0.100 bsc 2.54 bsc - f - 0.040 - 1.02 - k 0.027 0.034 0.69 0.86 - k1 0.027 0.045 0.69 1.14 2 l 0.500 0.750 12.70 19.05 1 l1 - 0.050 - 1.27 1 l2 0.250 - 6.35 - 1 q 0.010 0.045 0.25 1.14 - 45 o bsc 45 o bsc 3 45 o bsc 45 o bsc 3 n8 84 rev. 0 5/18/94
|
