micropac industries, inc. optoelectronic products division ? ?? ? 725 e.walnut str., garland, tx 75040 ? ?? ? (972)272-3571 ? ?? ? fax (972)487-6918 www.micropac.com e-mail: optosales @ micropac.com 66063 single-channel, very high speed, leadless chip carrier optocopler mii optoelectronic products division features: ? electrically similar to 6n134 ? hermetically sealed 24 pin lcc ? very high speed ? 5mhz bandwidth typical ? performance guaranteed over -55c to +125c ambient temperature range ? standard and high reliability screened parts available ? ttl compatible input and output ? high common mode rejection ? 1000 vdc isolation test voltage ? leadless chip carrier package ? faraday shield provides high common mode rejection description the 66063 single channel optocoupler consists of an led optically coupled to a high speed, high gain inverting detector gate. maximum isolation can be achieved while providing ttl output capable of switching with propagation delays of 55ns typical. the 66063 is a 24 pin hermetically sealed leadless chip carrier and is available in standard and screened versions or tested to customer specifications. absolute maximum ratings (no derating required up to 125c) storage temperature ........................................................................................................... ................................ -65c to +150c operating temperature .......................................................................................................... ............................... -55c to +125c lead solder temperature ....................................................................................................... .............................260c for 10 sec. peak forward input current ........................................................................................................................40 ma (<1ms duration) average forward input current ................................................................................................. ............................................. 20ma input power dissipation ....................................................................................................................................................... 35 mw reverse input voltage - v r ......................................................................................................................................................... 5v supply voltage - v cc ............................................................................................................................... .. 7v (1 minute maximum) output current - i o ................................................................................................................................................................. 25ma output power dissipation...................................................................................................................................................... 40mw output voltage - v o .................................................................................................................................................................... 7v total power dissipation ...................................................................................................................................................... 175mw package dimensions schematic diagram no. 1 lead mii 66063 xxxxx k 1 a 2 gnd vo vcc 16 14 15 identifier 0.400+.010,-.055 [10.160 +.254,-.127] ref. 0.020 (.508) all dimensions are in inches [millimeters] note: a .01 to 0.1 uf bypass capacitor must be connected between pins 15 and 10 typ 0.045 [1.13] 0.070 [1.78] 0.050 [1.27] 0.035 [0.89] r0.008 [r0.20] typ
micropac industries, inc. optoelectronic products division ? ?? ? 725 e.walnut str., garland, tx 75040 ? ?? ? (972)272-3571 ? ?? ? fax (972)487-6918 www.micropac.com e-mail: optosales @ micropac.com 66063 single?channel, very high speed, leadless chip carrier optocoupler, continued electrical characteristics over recommended temperature (t a = -55 c to +125 c) unless otherwise specified parameter symbol min typ** max units test conditions note high level output current i oh 5 250 av cc = 5.5v, v o = 5.5v, i f = 250 a low level output voltage v ol 0.5 0 .6 v v cc = 5.5v, i f = 10ma, i ol ( sinking ) = 10ma 6 high level supply current i cch 18 28 ma v cc = 5.5v, i f = 0 ( both channels ) low level supply current i ccl 26 36 ma v cc = 5.5v, i f = 20ma ( both channels ) input forward voltage v f 1.5 1 .75 v i f = 20ma, t a = 25c input reverse breakdown voltage bv r 5vi r = 10a, t a = 25c input-output insulation leakage current i i?o 1.0 a v i-0 = 1000vdc, relative humidity = 45% t a = 25c, t = 5s. 1 propagation delay time to high output level t plh 65 100 ns r l = 510 ? , c l = 15pf, i f = 13ma, t a = 25c 2, 6 propagation delay time to low output level t phl 55 100 ns r l = 510 ? , c l = 15pf, i f = 13ma, t a = 25c 3, 6 **all typical values are at v cc = 5v, t a = 25 c typical characteristics at t a = 25 c, v cc = 5v parameter symbol min typ max units test conditions note input capacitance c in 60 pf v f = 0, f = 1mhz input diode temperature coefficient ? v f ? t a -1.9 mv/ ci f = 20ma resistance (input-output) r i- o 10 12 ? v i-o = 500v 1 capacitance (input-output) c i-o 1.7 pf f = 1mhz 1 output rise-fall time (10-90%) t r , t f 35 ns r l = 510 ? , c l = 15pf, i f = 13ma 6 common mode transient immunity at high output cm h 1000 10000 v/ s v cm = 10v (peak) v o (min.) = 2v, r l = 510 ? , i f = 0ma 4 common mode transient immunity at low output cm l 1000 10000 v/ s v cm = 10v (peak) v o (max.) = 0.8v, r l = 510 ? , i f = 10ma 5 notes: 1. measured between pins 1 and 2 shorted together, and pins 10, 14 and 15 shorted together. 2. the t phl propagation delay is measured from the 6.5ma point on the trailing edge of the input pulse to the 1.5v point on the trailing e dge of the output pulse. 3. the t phl propagation delay is measured from the 6.5ma point on the leading edge of the input pulse to the 1.5v point on the leading edg e of the output pulse. 4. cm h is the max. tolerable common mode transient to assure that the output will remain in a high logic state (i.e. v o > 2.0v). 5. cm l is the max. tolerable common mode transient to assure that the output will remain in a low logic state (i.e. v o < 0.8v). 6. it is essential that a bypass capacitor (.01 to 0.1 f, ceramic) be connected from pin 10 to pin 15. recommended operating conditions parameter symbol min max units input current, low level each channel i fl 0 250 a input current, high level each channel i fh 12.5 2 0 ma supply voltage v cc 4.5 5 .5 v fan out (ttl load) each channel n 6 operating temperature t a -55 +125 c
|
