www.keithley.com 1.888.keithley (u.s. only) a greater measure of confidence fast t ransient response power supplies power sources figure 1. comparison of the voltage outputs of a lithium-ion battery (with an internal resistance of 260m ? ) and the model 2306 s battery channel (programmed with an output resistance of 260m ? ) when powering a cellular telephone as it makes the transition from standby mode to transmit mode. the single-channel model 2302 battery simulator and model 2306 dual channel battery/charger simulator were designed specifically for develop- ment and test applications for portable, battery- operated products, such as cellular and cordless telephones, mobile radios, and pagers. these pre- cision power supplies have ultrafast transient response so they can have output characteristics identical to actual batteries. these supplies employ a unique variable output resistance so the voltage output can emulate a battery? response (u.s. patent no. 6,204,647). they provide stable voltage outputs, even when a device-under-test (dut) makes the rapid transition from the standby (low current) state to the rf transmission (high cur- rent) state. in addition, they can monitor dut power consumption by measuring both dc cur- rents and pulse load currents. the model 2302? and the model 2306? battery-simulator channel can be programmed to operate like a discharged rechargeable battery, sinking current from a sepa- rate charger or the model 2306? charger-simulator channel. maximize test throughput with accurate battery simulation the battery-output channels of the models 2302 and 2306 are designed to simulate the output response of a battery. this capability, combined with their fast transient response, makes it possible to power the device during testing in exactly the same way as a battery will power the device during actual use. the output resistance of the model 2302? and the model 2306? battery channel can be programmed (with 10m ? resolution) over the range from 0 ? to 1 ? so that the output resistance can be set to the same level as the output resistance of the battery that powers the device. portable wireless devices make great demands on their battery power sources. the battery must source load currents that can jump virtually instantaneously from a standby current level (100?00ma) to a full- power rf transmission current level (1?a). in other words, the load current on the battery can increase rapidly by a factor of 700?000%. as a result, the battery voltage drops by an amount equal to the value of the current change multiplied by the battery? internal resistance. the models 2302 and 2306 power sup- plies enable test systems to duplicate this voltage drop by programming their output resistance to be equiv- alent to that of the battery that will power the device. this allows wireless device manufacturers to test their products under the same power conditions that they will encounter in actual use. (see figure 1 .) in response to large load changes, the model 2302 and the battery channel of the model 2306 have tran- sient voltage droops of less than 100mv and transient recovery times of less than 60?, even when the ultrfast response to transient load currents choice of single- or dual- channel supplies optimized for development and testing of battery-powered devices variable output resistance for simulating battery response (u.s. patent no. 6,204,647) pulse peak, average, and baseline current measurements 100na dc current sensitivity current step measure function sink up to 3a open sense lead detection built-in digital voltmeter 2302 battery simulator 2306, 2306-pj battery charger/simulators
www.keithley.com 1.888.keithley (u.s. only) a greater measure of confidence fast t ransient response power supplies power sources test leads between the power supply and the dut are long. this fast transient response, combined with the supplies?variable output resistance, allows engineers to test their portable products under the most realistic operating conditions and eliminate false failures due to conventional power supplies with slow response times. (see the side- bar titled ?onventional power supplies and wireless device testing.? these supplies also eliminate the large stabilizing capacitors needed at the dut to compensate for the large droop that occurs when testing with conventional power sup- plies. by varying the output resistance, which can be done while the output is turned on, test engi- neers can simulate the operation of different bat- tery types, as well as batteries nearing the end of their useful lives. the models 2302 and 2306 ensure maximum pro- duction throughput when testing portable devices by minimizing false failures, minimizing the num- ber of test set-ups by performing multiple tests with the same power supply, and minimizing test fixture complexity by eliminating the need for voltage-stabilizing capacitors. measure load currents for power consumption verification or analysis as manufacturers of portable devices strive to extend their products?battery life, measuring load currents accurately has become increasingly essen- tial in both design and production test in order to ensure the product meets its demanding specifica- tions. comprehensive testing of these devices requires measuring peak currents, average cur- rents, and baseline currents in various operation modes. when testing these devices, these meas- urements are complicated by the pulsating nature of load currents, such as the transmit and receive load currents of digital cellular phones. the models 2302 and 2306 can measure the peak and average currents of pulses as short as 60? and as long as 833ms. (see figure 2 .) measure long-period waveform currents for pulse trains with periods longer than 850ms, the models 2302 and 2306 offer a unique, long integration current measurement mode. this mode can provide an average measurement of a current waveform from 850ms up to 60 seconds long. measure low currents accurately the models 2302 and 2306 are based on keithley? expertise in low current measurement technolo- gies, so they?e well-suited for making fast, accu- rate measurements of sleep and standby mode currents. with 100na resolution and 0.2% basic accuracy, they provide the precision needed to monitor the low sleep mode currents of both today? battery-operated products and tomorrow?. ordering information 2302 battery simulator 2306 dual-channel battery charger/simulator 2306-pj dual-channel battery charger/simulator with 500ma range these products are available with an extended warranty. accessories supplied user and service manuals, cs-846 output connectors mating terminal accessories available 2306-disp remote display cables 7007-1 shielded ieee-488 cable, 1m (3.3 ft) 7007-2 shielded ieee-488 cable, 2m (6.6 ft) rack mount kits 4288-1 single fixed rack mount kit 4288-2 dual fixed rack mount kit other 2304-ew 1 year warranty extension 2306-ew 1 year warranty extension kpci-488 ieee-488 interface/controller for the pci bus kpc-488.2at ieee-488 interface card for ibm pc/at (full slot) testpoint test development software 2302 battery simulator 2306, 2306-pj battery charger/simulators conventional power supplies and wireless device testing during production testing, supplying power to a device that undergoes large, instanta- neous load current changes can be extremely difficult. changes like this force a convention- al power supply? output voltage to fall instan- taneously. when the power supply? control circuitry senses the error condition (the dif- ference in voltage between the programmed level and the actual level), it attempts to cor- rect or restore the voltage to the pro- grammed level. during this time, the voltage will fall or droop substantially, with the amount of the droop depending on the size of the load current change. the recovery time depends on the transient response of the power supply? control loop. conventional power supplies have transient voltage drops of >1v when confronted with load current changes of up to 1000%, and take up to a mil- lisecond to recover to the programmed volt- age. for portable devices such as cellular phones that operate at full power for only short intervals, the full power event is over before the conventional power supply can recover. for example, a cellular phone designed to the gsm cellular phone standard transmits and receives information in 576? pulses. if the power supply used to test these types of phones cannot recover quickly enough, the performance of the phone dur- ing testing will be compromised by the power supply. if the power supply voltage drops below the threshold of the phone? low bat- tery detection circuitry for long enough, then the phone will turn off during testing, giving a false indication of a failed device. high current level trigger level average current level high time low current level low time average time (out to 60s with long integration) figure 2. built-in pulse current measurement functions allow test engineers to measure peak, aver- age, and baseline load currents.
www.keithley.com 1.888.keithley (u.s. only) a greater measure of confidence fast t ransient response power supplies power sources simulate a discharged battery for charger testing the models 2302 and 2306 can sink up to 3a continuously, just like an elec- tronic load. this allows these supplies to simulate a discharged rechargeable battery for use in testing the performance of battery chargers or battery charg- er control circuitry. the model 2306 battery/charger simulator combines the functionality of both the charging current source (the charger channel) and the current sinking to simulate the recharging of a discharged battery (the battery channel) in a sin- gle enclosure. (see figure 3 ). open-sense lead detection the model 2302 and 2306 have an automatic open?ense lead detection capability, which indicates if there is a broken remote sense lead or an open connection from a remote sense lead to the test fixture. to ensure the output voltage does not change from the programmed level, which could cause pro- duction devices to be improperly calibrated, the user can set high and low limits around the desired voltage level. independent digital voltmeter inputs many programmable power supplies offer output readback capabilities, but the model 2302 and 2306 also offer dvm inputs. both instruments allow meas- uring signals from ?v to +30v dc anywhere in the test system with the same rated accuracy as the voltage readback. the model 2306 has two sets of dvm inputs; the model 2302 has one. the dvms and the power sources can oper- ate simultaneously. for many applications, these built-in dvms eliminate the expense and space required to add a separate voltage measurement instrument. remote display option if the model 2302, 2306, or 2306-pj must be mounted in a location in which the display is not readily visible, an optional model 2306-disp display module can be mounted at a more convenient point, then plugged into the power supply unit. the display module also includes all instrument controls, so that the power supply can be operated remotely from the more accessible location. r + battery channel charger channel v battery v charger > v battery battery terminals charger terminals + ii figure 3. for charger control circuit testing applications, the model 2306 and 2306-pj can provide the functions of both a charger-simulating source and a discharged battery simulator. 2302 battery simulator 2306, 2306-pj battery charger/simulators general isolation (low?arth): 22v dc max. do not exceed 60v dc between any two terminals of either connector. programming: ieee-488.2 (scpi). user-definable power-up states: 5. rear panel connectors: two 8-position quick disconnect terminal block for output (4), sense (2), and dvm (2). temperature coefficient (outside 23? ??): derate accuracy specification by (0.1 speci- fication)/?. operating temperature: 0 to 50? (derate to 70%). 0 to 35? (full power). storage temperature: ?0 to 70?. humidity: <80% @ 35? non-condensing. display type: 2-line 16-character vfd. remote display/keypad option: disables standard front panel. dimensions: 89mm high 213mm wide 411mm deep (3 1 2 in 8 3 8 in 16 3 16 in). net weight: 3.2kg (7.1 lbs). shipping weight: 5.4kg (12 lbs). input power: 100?20v ac/220?40v ac, 50 or 60hz (auto detected at power-up). power consumption: 150va max. warranty: two years parts and labor on materials and workmanship. emc: conforms with european union directive directive 89/336/eec. safety: conforms with european union directive 73/23/eec (meets en61010-1/iec 1010). ac line leakage current: 450 a @ 110vac, typ.; 600 a @ 220v, typ. relay control port: 4-channel, each capable of 100ma sink, 24v max. total port sink capaci- ty (all 4 combined) is 250ma max. accepts db-9 male plug. model 2306 rear panel showing 8-position power output connectors, rj-45 remote display connector, db-9 relay output connector, ieee- 488 connector, and power input socket.
model 2302, 2306, 2306-pj specifications power sources www.keithley.com 1.888.keithley (u.s. only) a greater measure of confidence output #1 (battery) dc voltage output (2 years, 23? 5?) output voltage: 0 to +15v dc. output accuracy: ?0.05% + 3mv). programming resolution: 1mv. readback accuracy 1 : ?0.05% + 3mv). readback resolution: 1mv. output voltage settling time: 5ms to within stated accuracy. load regulation: 0.01% + 2mv. line regulation: 0.5mv. stability 2 : 0.01% + 0.5mv. measurement time choices: 0.01 to 10plc7, in 0.01plc steps. average readings: 1 to 10. reading time 1, 8, 9 : 31ms, typical. transient response: high bandwidth low bandwidth transient recovery time 13 <40? 3 or <60? 4 <80? 3 or <100? 4 transient voltage drop <75mv 3 or <100mv 4 <250mv 3 or <400mv 4 remote sense: 1v max. drop in each lead. add 2mv to the voltage load regulation specification for each 1v change in the negative output lead due to load current change. remote sense required. integrity of connection continually monitored. if compromised, output will turn off automatically once settable window (? to ?v) around normal voltage exceeded. variable output impedance range: 0 to 1.00 ? in 0.01 ? steps. value can be changed with output on. dc current (2 years, 23? 5?) continuous average output current (2302): 0?v: 5a max. >4v: i max = 60w/(v set +6) (not intended to be operated in parallel). continuous average output current (2306): channel #2 (charger) off: i = 50w/(v set channel 1 + 6v); 5a max. channel #2 (charger) on: i = (50w ?power consumed by channel #2)/(v set channel 1 + 6v); 5a max. the power consumed by channel #2 is calculated as: channel #2 sourcing current: power consumed = (v set channel 2 + 6v) (current supplied) channel #2 sinking current: power consumed = 5 (sink current) peak currents can be a maximum of 5a provided the average current is within the above limits. continuous average sink current: channel #2 (charger) off: 0?v: 3a max. 5?5v: derate 0.2a per volt above 5v. compliance setting controls sinking. channel #2 (charger) on: available current = (50w ?power consumed by channel #2)/5; 3a max. (0?v). derate 0.2a per volt above 5v. source compliance accuracy: ?0.16% + 5ma) 5 . programmed source compliance resolution: 1.25ma. readback accuracy 1 : 5a range: ?0.2% + 200 a). 5ma range: ?0.2% + 1 a). 500ma range: ?0.2% + 20 a) (2306-pj only). readback resolution: 5a range: 100 a. 5ma range: 0.1 a. 500ma range: 10 a (2306-pj only). load regulation: 0.01% + 1ma. line regulation: 0.5ma. stability 4 : 0.01% + 50 a. measurement time choices: 0.01 to 10plc 7 , in 0.01plc steps. average readings: 1 to 10. reading time 1, 8, 9 : 31ms, typical. pulse current measurement operation trigger level: 5a current range 5a range: 5ma to 5a, in 5ma steps. 1a range: 1ma to 1a, in 1ma steps. 100ma range: 0.1ma to 100ma, in 100 a steps. 500ma current range (2306-pj) 500ma range: 0.5ma to 500ma, in 0.5ma steps. 100ma range: 0.1ma to 100ma, in 100 a steps. 10ma range: 100 a to 10ma, in 100 a steps. trigger delay: 0 to 100ms, in 10? steps. internal trigger delay: 15?. high/low/average mode: measurement aperture settings: 33.3? to 833ms, in 33.3? steps. average readings: 1 to 100. pulse current measurement accuracy 11 (2 years, 23? ??): aperture accuracy ?% reading + offset + rms noise 10 ) <100 ? 0.2% + 900 a + 2 ma 100 ? ?200 ? 0.2% + 900 a + 1.5 ma 200 ? ?500 ? 0.2% + 900 a + 1 ma 500 ? ?<1 plc 0.2% + 600 a + 0.8 ma 1 plc 12 0.2% + 400 a + 0 ma >1 plc 0.2% + 400 a + 100 a burst mode current measurement measurement aperture: 33.3?. conversion rate: 3650/second, typical. internal trigger delay: 15?. number of samples: 1 to 5000. transfer samples across ieee bus in binary mode: 4800 bytes/s, typical. long integration mode current measurement 2302, 2306: available on 5a range. 2306-pj: available on 5a and 500ma ranges. measurement time 6 : 850ms (840ms) to 60 seconds in 1ms steps. digital voltmeter input (2 years, 23? 5?) input voltage range: ? to +30v dc. input impedance : 2m ? typical. maximum voltage (either input terminal) with respect to output low: ?v, +30v. reading accuracy 1 : ?0.05% + 3mv). reading resolution: 1mv. connector: hi and lo input pair part of output #1? terminal block. measurement time choices: 0.01 to 10plc 7 , in 0.01plc steps. average readings: 1 to 10. reading time 1, 8, 9 : 31ms, typical. 2302 battery simulator 2306, 2306-pj battery charger/simulators
www.keithley.com 1.888.keithley (u.s. only) a greater measure of confidence model 2302, 2306, 2306-pj specifications power sources output #2 (charger) dc voltage output (2 years, 23? 5?) output voltage: 0 to +15v dc. output accuracy: ?0.05% + 10mv). programming resolution: 10mv. readback accuracy 1 : ?0.05% + 3mv). readback resolution : 1mv. output voltage settling time: 5ms to within stated accuracy. load regulation: 0.01% + 2mv. line regulation: 0.5mv. stability 2 : 0.01% + 0.5mv. measurement time choices: 0.01 to 10plc 7 , in 0.01plc steps. average readings: 1 to 10. reading time 1, 8, 9 : 31ms, typical. transient response: high bandwidth low bandwidth transient recovery time 13 <50? 3 or <80? 4 <60? 3 or <100? 4 transient voltage drop <120mv 3 or <150mv 4 <160mv 3 or <200mv 4 remote sense: 1v max. drop in each lead. add 2mv to the voltage load regulation specification for each 1v change in the negative output lead due to load current change. remote sense required. integrity of connection continually monitored. if compromised, output will turn off automatically once settable window (? to ?v) around normal voltage exceeded. dc current (2 years, 23? 5?) continuous average output current: channel #1 (battery) off: i = 50w/(v set channel 2 + 6v); 5a max. channel #1 (battery) on: i = (50w ?power consumed by channel #1)/(v set channel 2 + 6v); 5a max. the power consumed by channel #1 is calculated as: channel #1 sourcing current: power consumed = (v set channel 1 + 6v) (current supplied) channel #1 sinking current: power consumed = 5 (sink current) peak currents can be a maximum of 5a provided the average current is within the above limits. continuous average sink current: channel #1 (battery) off: 0?v: 3a max. 5?5v: derate 0.2a per volt above 5v. compliance setting controls sinking. channel #1 (battery) on: available current = (50w ?power consumed by channel #1)/5; 3a max. (0?v). derate 0.2a per volt above 5v. source compliance accuracy: ?0.16% + 5ma) 5 . programmed source compliance resolution: 1.25ma. readback accuracy 1 : 5a range: ?0.2% + 200 a). 5ma range: ?0.2% + 1 a). readback resolution: 5a range: 100 a. 5ma range: 0.1 a. load regulation: 0.01% + 1ma. line regulation: 0.5ma. stability 4 : 0.01% + 50 a. measurement time choices: 0.01 to 10plc 7 , in 0.01plc steps. average readings: 1 to 10. reading time 1, 8, 9 : 31ms, typical. pulse current measurement operation trigger level: 5ma to 5a, in 5ma steps. trigger delay: 0 to 100ms, in 10? steps. internal trigger delay: 15?. high/low/average mode: measurement aperture settings: 33.3? to 833ms, in 33.3? steps. average readings: 1 to 100. pulse current measurement accuracy 11 (2 years, 23? ??): aperture accuracy ?% reading + offset + rms noise 10 ) <100 ? 0.2% + 900 a + 2 ma 100 ? ?200 ? 0.2% + 900 a + 1.5 ma 200 ? ?500 ? 0.2% + 900 a + 1 ma 500 ? ?<1 plc 0.2% + 600 a + 0.8 ma 1 plc 12 0.2% + 400 a + 0 ma >1 plc 0.2% + 400 a + 100 a burst mode current measurement measurement aperture: 33.3?. conversion rate: 2040/second, typical. internal trigger delay: 15?. number of samples: 1 to 5000. transfer samples across ieee bus in binary mode: 4800 bytes/s, typical. long integration mode current measurement measurement time 6 : 850ms (840ms) to 60 seconds in 1ms steps. digital voltmeter input (2 years, 23? 5?) input voltage range: ? to +30v dc. input impedance : 2m ? typical. maximum voltage (either input terminal) with respect to output low: ?v, +30v. reading accuracy 1 : ?0.05% + 3mv). reading resolution: 1mv. connector: hi and lo input pair part of output #2? terminal block. measurement time choices: 0.01 to 10plc 7 , in 0.01plc steps. average readings: 1 to 10. reading time 1, 8, 9 : 31ms, typical. 1 plc = 1.00. 2 following 15 minute warm-up, the change in output over 8 hours under ambient temperature, constant load, and line operating conditions. 3 remote sense, at output terminals, 0.5a to 5a typical. 4 remote sense, with 4.5m (15 ft) of 16 gauge (1.31mm2) wire and 1 ? resistance in each lead to simulate typical test environment, 1.5a load change (0.15a to 1.65a). 5 minimum current in constant current mode is 6ma. 6 60hz (50hz). 7 plc = power line cycle. 1plc = 16.7ms for 60hz operation, 20ms for 50hz operation. 8 display off. 9 speed includes measurement and binary data transfer out of gpib. 10 typical values, peak-to-peak noise equals 6 times rms noise. 11 based on settled signal: 100? pulse trigger delay. 12 also applies to other apertures that are integer multiples of 1plc. 13 recovery to within 20mv of previous level. 2302 battery simulator 2306, 2306-pj battery charger/simulators
|
