1 www.protekdevices.com 05087.r1 1/03 emc3.3f-lc thru emc15f-lc tvs/low pass l/c fil ter arra ys applications ? high-speed networks ? graphics/video cards ? global positioning systems ? wireless networks iec compatibility (en61000-4) ? 61000-4-2 (esd): air - 15kv, contact - 8kv ? 61000-4-4 (eft): 40a - 5/50ns features ? 300 watts peak pulse power per line (tp=8/20s) ? emi/rfi low pass filtering ? very low insertion loss: < 0.5db up to 200 mhz ? excellent matching over the operating frequency ? protects 3.3 - 15 volt i/o ports ? 50 ohm network terminations ? l/c bessel filter ? ? ? ? ? low capacitance: 10pf mechanical characteristics ? molded jedec so-16wb (wide body) package ? weight 0.15 grams (approximate) ? flammability rating ul 94v-0 ? 16mm tape and reel per eia standard 481 ? marking: logo, part number & pin one defined by dot on top of package circuit diagram so-16wb (wide body) 05087 . . . engineered solutions for the transient environment? 1 16 15 14 13 12 11 10 9 2 3 4 5 6 7 8 gnd gnd gnd gnd gnd gnd gnd gnd out out out out in in in in
2 www.protekdevices.com emc3.3f-lc thru emc15f-lc 05087.r1 1/03 device characteristics maximum ratings @ 25c unless otherwise specified operating temperature symbol value -55 c to 150 c c c -55 c to 150 c units t j t stg parameter storage temperature peak pulse power (t p = 8/20s) - see figure 1 p pp 300 watts electrical characteristics per line @ 25c unless otherwise specified pa rt number maximum operating voltage v (op) volts minimum breakdown voltage (see note 1) @ 1ma v (br) volts maximum clamping voltage (see fig. 5) @ i pp = 5a v c volts cut-off frequency @ -3db f c mhz emc3.3f-lc emc5.0f-lc emc8.0f-lc emc12f-lc emc15f-lc 3.3 5.0 8.0 12.0 15.0 4.0 6.0 8.5 13.3 16.7 100 50 5 5 5 9.0 11.0 16.6 24.0 30.0 maximum leakage current (see note 1) @v wm i d a typical capacitance (see note 2) @ 0v, 1 mhz c pf 10 10 10 10 10 500 500 500 500 500 note 1: apply positive (negative) potential between input pins to ground pins, output open. note 2: measure capacitance between output pins to ground pins.
3 www.protekdevices.com 05087.r1 1/03 emc3.3f-lc thru emc15f-lc graphs 0 25 50 75 100 125 150 t l - lead temperature - c 20 40 60 80 100 % of rated power peak pulse power 8/20s average power figure 3 power derating curve 0 0 5 10 15 20 25 30 t - time - s 0 20 40 60 80 100 120 i pp - peak pulse current - % of i pp test waveform parameters t f = 8s t d = 20s t f peak value i pp e -t t d = t i pp /2 figure 2 pulse wave form 0.1 1 10 100 1,000 10,00 0 t d - pulse duration - s 300w 8/20s waveform 10 100 1,000 10,000 p pp - peak pulse power - watts figure 1 peak pulse power vs pulse time
4 www.protekdevices.com emc3.3f-lc thru emc15f-lc 05087.r1 1/03 copyright ? protek devices 2003 specifications: protek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except jedec). design changes: protek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer?s and that in furnishing engineering and technical assistance, protek assumes no responsibility with respect to the selection or specifications of such products. package outline & dimensions protek devices 2929 south fair lane, tempe, az 85282 tel: 602-431-8101 fax: 602-431-2288 e-mail: sales@protekdevices.com web site: www.protekdevices.com p ar t number suffixes used for t ape & reel/b ulk ordering: surface mount product is taped and reeled in accordance with eia-481. suffix-t13 = 13 inch reel - 2,500 pieces per reel i.e: emc5.0-lc-t13 no suffix = product shipped in tubes of 46 pcs per tube a b c d f g j k p r 10.45 7.60 2.65 0.49 0.90 1.27 bsc 0.32 0.25 10.55 0.75 0.400 0.292 0.093 0.014 0.020 0.05 bsc 0.010 0.004 0.395 0.010 0.411 0.299 0.104 0.019 0.035 0.05 bsc 0.012 0.009 0.415 0.029 10.15 7.40 2.35 0.35 0.50 1.27 bsc 0.25 0.10 10.05 0.25 dim min max min max millimeters inches package dimensions notes: 1. - t - = seating plane and datum surface. 2. dimensions ? a ? and ? b ? are datum. 3. dimensions ? a ? and ? b ? do not include mold protrusions. 4. maximum mold protrusion is 0.015 ? (0.380 mm) per side. 5. dimensioning and tolerances per ansi y14.5m, 1982. 6. dimensions are exclusive of mold flash and metal burrs. package outline so-16 (wide body) mounting pad m -a- -b- p d g -t- k c j r x 45 o f 0.010 ? (0.25 mm) m b m 8 pl 0.010 ? (0.25 mm) s b m 16 pl t a s 16 9 8 1 0.050 ? typ 0.030 ? 0.005 ? 0.420 ? min 0.325 ? 0.005 ? 0.045 ? 0.005 ? 0 o - 7 o 06008 rev 1 - 11/01
|
