View HFDOM40MRXXX_2439995.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

hanbit HFDOM40MRXXX url:www.hbe.co.kr 1 / 1 hanbit electronics co., ltd. rev. 1.0 (november. 2003) 1. product overview general description the HFDOM40MRXXX series 40pin flash disk module is a flas h technology based with true ide interface flash memory card. it is constructed with flash disk controller chip and nand-type (samsung) flash me mory device. the hfdom40mr- xxx series operates in both 3.3-volt and 5.0-volt power supplies. it comes in capacity of 16, 32, 64, 128, 192, 256, 512 mb and up to 1gb mb formatted 40pin type . by optimizing flash memory management, the life of this HFDOM40MRXXX series can be extended to its maximum level. because the ecc function is included, the correctness of data transfer between the HFDOM40MRXXX series and a true ide compatible interfac e device can be guaranteed. the HFDOM40MRXXX series is fully compatible with applications such as cpu card / board, set top box, industry / military pc / notebook, security equipmen t, measuring instrument and embedded systems. features - ata / true ide compatible host interface - ata command set compatible - automatic sensing of pc card ata or true ide host interface. - very high performance, low power consumption - automatic error detection and error correction - auto standby to save power consumption. - supports automatic power down and wake up - support for 8 or 16 bit host transfers - 3.3v/5.0v operation voltage - host interface bus width : 8/16 bit access - flash interface bus width : 8 bit access - capacity : min. 16mb ~ max. 1gb product specifications capacities : 16, 32, 48, 64, 96, 128, 192, 256, 512 and up to 1gb (formatted) system compatibility : please refer to the compatibility list of index. performance : host data transfer rates : up to 16.6 mb/s ec, pio mode 4; 16.6mb/sec, multi-word dma mode 2; 33mb/sec 40pin flash disk module min.8mb ~ max.1gb, true ide interface mode, 3.3v / 5.0v operating part no . HFDOM40MRXXX
hanbit HFDOM40MRXXX url:www.hbe.co.kr 2 / 2 hanbit electronics co., ltd. rev. 1.0 (november. 2003) reliability : mtbf : xxx,xxx hours ecc : embedded ecc function data retention : 10 years operating voltage : 3.3v / 5.0v 10% power consumption : 3.3v 5% read mode <40 ma write mode <60 ma stop mode <2 ma environment conditions : operating temperature 0c to + 65c storage temperature - c to + c relative humidity 8% to 95%, non-condensing electrical specifications table 1.1 absolute maximum ratings symbol parameter rating units v dd power supply -0.3 to 6.0 v v in input voltage -0.3 to v dd +0.3 v v out output voltage -0.3 to v dd +0.3 v t stg storage temperature -25 to 125 o c table 1.2 recommended operating conditions symbol parameter min. max. units v dd power supply 3.0 5.5 v v in input voltage 0 v dd v t opr operating temperature 0 65 o c table 1.3 dc characteristics sym. parameter min typ max units v il input low voltage 0.6 v v ih input high voltage 2.4 v v il schmitt input low voltage 1.0 v v ih schmitt input high voltage 1.8 v v ol output low voltage 0.4 v v oh output high voltage 2.5 v r i input pull up/down resistance 50 k ?
hanbit HFDOM40MRXXX url:www.hbe.co.kr 3 / 3 hanbit electronics co., ltd. rev. 1.0 (november. 2003) capacity specifications table 1.4 capacity specifications part number capacity ( formatted ) cylinders heads sectors note hfdom40mr032 32,24.3712 mbytes 492 8 16 installtion guide 1) setting method ? make sure your computer is turned off before you open the case. plug the carefully into the 40pin ide slot on your computer. caution: make sure to align pin1 on host adapter interface c onnector with pin 1 on your flash disk module. pin 1 is indicated by a triangle on the flash disk module connector. the flash disk module is used power connector cable of the computer. caution: if you need to remove your flash disk module, use both hands to pull it out carefully. check all cable connections and then replace your computer cover. 2) bios setting method before you format or partition your new drive, you must c onfigure your computer's bios so that the computer can recognize your new drive. ? turn your computer on. as your computer start up, watch the screen for a message describing how to run the system setup program on the screen (som etimes called bios or cmos setup). this is usually done by pressing a special key, such as delete , esc or f1 during startup. see your computer m anual for details. press the appropriate key to run the system setup program. if your bios provides automatic drive detecti on (an "auto" drive type), select this option. ( we recommend to use normal / chs mode to partition your flash disk module to get the maximum formatted capacity. ) this allows your computer to configure itself automatically for your new drive. if your bios dose not provide ?aut o? drive detection, select "user-d efined" drive setting and enter the chs values from the table. bios settings (see specification) capac ity cylinders heads sectors(unformatted) save the settings and exit the syst em setup program. ( your computer will automatically reboot ) after you configure your computer, you can us e the standard dos commands to partiti on and format your flash disk module, as described below. 3) formatting method to partition your new flash disk module with microsoft dos program : ? insert a bootable dos diskette into your diskette drive and restart your computer. insert a dos program diske tte that contains the fdisk.exe and format.com programs into your diskette drive. use the same do s version that is on your bootable diskette. at the a:\ > prompt, type ?fdisk? and press enter . select ?create dos partition or logical dos drive? by pressing 1 . then press enter . select ?create primary dos partition? by pressing 1 again. then press enter . create your first drive partition. if you are creating a parti tion that will be used to boot your computer (drive c), make sure that the partition is marked active. ? create an extended partition and additional l ogical drives as necessary, until a ll the space on your new hard drive has been partitioned. when the partitioning is complete, fdisk reboots your computer. caution: make sure to use the correct driv e letters so that you do not format a drive that already contains data. at the a:\ > prompt, type ?format c:/s? , where c is the letter of your first new partition, repeat the format process
hanbit HFDOM40MRXXX url:www.hbe.co.kr 4 / 4 hanbit electronics co., ltd. rev. 1.0 (november. 2003) for all the new partitions you have created. ? after you format your drive, it is ready to use. 2. pin information pin assignments and pin type table 2.1 pin assignment and pin type pin signal pin type pin signal pin type 1 /reset i 2 gnd ground 3 d07 i/o 4 d08 i/o 5 d06 i/o 6 d09 i/o 7 d05 i/o 8 d10 i/o 9 d04 i/o 10 d11 i/o 11 d03 i/o 12 d12 i/o 13 d02 i/o 14 d13 i/o 15 d01 i/o 16 d14 i/o 17 d00 i/o 18 d15 i/o 19 gnd dc 20 key pin -- 21 inpack -- 22 gnd ground 23 /iow i 24 gnd ground 25 /ior i 26 gnd ground 27 iordy o 28 reserved -- 29 reg -- 30 gnd ground 31 irq o 32 /iois16 o 33 a01 i 34 /pdiag i/o 35 a00 i 36 a02 i 37 /cs0 i 38 /cs1 i 39 /dasp i/o 40 gnd ground
hanbit HFDOM40MRXXX url:www.hbe.co.kr 5 / 5 hanbit electronics co., ltd. rev. 1.0 (november. 2003) signal descriptions table 2.2 signal descriptions signal name dir. pin description a[2:0] i 33,35,36 in true ide mode only a[2:0] are used to select the one of ei ght registers in the task file, the remaining address lines should be grounded by the host. -pdiag i/o 34 this input / output is the pass diagnos tic signal in the master / slave handshake protocol. -dasp i/o 39 in the true ide mode, this input/ output is the disk active/slave present signal in the mast er/slave handshake protocol. -cs0, -cs1 i 37,38 cs0 is the chip select for the task file registers while cs2 is used to select the alternate status register and the device control register. d[15:00] i/o 3,4,5,6, 7,8,9,10, 11,12,13, 14,15,16, 17,18 all task file operations occur in by te mode on the low order bus d00-d07 while all data transfers are 16 bit using d00-d15. gnd -- 2,19,22, 24,26, 30,40, ground. -ior i 25 this is an i/o read strobe generated by the host. -iow i 23 the i/o write strobe pulse is used to clock i/o data on the card data bus into the storage card controller r egisters when the storage card is configured to use the i/o interface. t he clocking will occur on the negative to positive edge of the signal (trailing edge). irq o 31 in true ide mode signal is the active high interrupt request to the host. -reset i 1 this input pin is the active low hardware reset from the host. iordy o 27 this output signal may be used as iordy. -iois16 o 32 this output signal is asserted low when this device is expecting a word data transfer cycle.
hanbit HFDOM40MRXXX url:www.hbe.co.kr 6 / 6 hanbit electronics co., ltd. rev. 1.0 (november. 2003) block diagram pcmcia ata interface 8051 controller address decoder ecc flash host nand flash device nand flash device nand flash device nand flash device host interface ecc flash host nand flash device nand flash device nand flash device nand flash device mux program ram data ram buffer program rom a channel b channel figure 2.1 block diagram
hanbit HFDOM40MRXXX url:www.hbe.co.kr 7 / 7 hanbit electronics co., ltd. rev. 1.0 (november. 2003) registers overview ata register set definitions (1) . error register (2) . device/head register (3) . status & alternate status register (4) . device control register (5) . card address register (6) . data register (7) . feature register (8) . sector count register (9) . sector number register (10) . cylinder low register (11) . cylinder high register pcmcia register set definitions (1) . pcmcia configuration option register (2) . pcmcia configuration and status register (3) . pcmcia pin replacement register (4) . pcmcia socket and copy register ata register set definitions: error register this register contains additional information about the s ource of an error when an error is indicated in bit 0 of the status register. the bits are defined as follows: d7 d6 d5 d4 d3 d2 d1 d0 bbk unc 0 idnf 0 abrt 0 amnf this register is also accessed on data bits d15-d8 during a write operation to offset 0 with -ce2 low and -ce1 high. bit 7 (bbk) : this bit is set when a bad block is detected. bit 6 (unc) : this bit is set when an uncorrectable error is encountered. bit 5 : this bit is 0. bit 4 (idnf) : the requested sector id is in error or cannot be found. bit 3 : this bit is 0. bit 2 (abort) : this bit is set if the command has been abor ted because of a compactflash storage card status condition: (not ready, write fault, et c.) or when an invalid command has been issued.
hanbit HFDOM40MRXXX url:www.hbe.co.kr 8 / 8 hanbit electronics co., ltd. rev. 1.0 (november. 2003) bit 1 this bit is 0. bit 0 (amnf) this bit is set in case of a general error. device/head register the drive/head register is used to select the drive and head. it is also used to select lba addressing instead of cylinder/head/sect or addressing. the bits are defined as follows: d7 d6 d5 d4 d3 d2 d1 d0 1 lba 1 drv hs3 hs2 hs1 hs0 bit 7 : this bit is set to 1. bit 6 : lba is a flag to select either cylinder/head/se ctor (chs) or logical block address mode (lba). when lba=0, cylinder/head/sector mode is sele cted. when lba=1, logical block address is selected. in logical block mode, the logical block address is interpreted as follows: lba7-lba0: sector number register d7-d0. lba15-lba8: cylinder low register d7-d0. lba23-lba16: cylinder high register d7-d0. lba27-lba24: drive/head r egister bits hs3-hs0. bit 5 : this bit is set to 1. bit 4 (drv): drv is the drive number. when drv=0, drive (car d) 0 is selected. when drv=1, drive (card) 1 is selected. the compactflash storage card is set to be card 0 or 1 using the copy field (drive #) of the pcmcia socket & copy configuration register. bit 3 (hs3) : when operating in the cylinder , head, sector m ode, this is bit 3 of the head number. it is bit 27 in the logical block address mode. bit 2 (hs2) : when operating in the cylinder, head, sector m ode, this is bit 2 of the head number. it is bit 26 in the logical block address mode. bit 1 (hs1) : when operating in the cylinder, head, sector m ode, this is bit 1 of the head number. it is bit 25 in the logical block address mode. bit 0 (hs0) : when operating in the cylinder, head, sector m ode, this is bit 0 of the head number. it is bit 24 in the logical block address mode. status & alternate status register these registers return the compactflash storage ca rd status when read by t he host. reading the status register does clear a pending interrupt while reading the auxiliary status r egister does not. the status bits are described as follows: d7 d6 d5 d4 d3 d2 d1 d0 busy rdy dwf dsc drq corr 0 err bit 7 (busy) : the busy bit is set when the compactflash storage card has access to the command buffer
hanbit HFDOM40MRXXX url:www.hbe.co.kr 9 / 9 hanbit electronics co., ltd. rev. 1.0 (november. 2003) and registers and the host is locked out from accessing the command register and buffer. no other bits in this register are valid when this bit is set to a 1. bit 6 (rdy) : rdy indicates whether the device is capabl e of performing compactflash storage card operations. this bit is cleared at power up and remains cleared until the compactflash storage card is ready to accept a command. bit 5 (dwf) : this bit, if set, indicates a write fault has occurred. bit 4 (dsc) : this bit is set when the compactflash storage card is ready. bit 3 (drq) : the data request is set when the compactfla sh storage card requires that information be transferred either to or from t he host through the data register. bit 2 (corr) : this bit is set when a correctable dat a error has been encountered and the data has been corrected. this condition does not termi nate a multi-sector read operation. bit 1 (idx) : this bit is always set to 0. bit 0 (err) : this bit is set when the previous command has te rminated with some type of error. the bits in the error register contain additional informati on describing the error. it is recommended that media access commands (such as read sectors and write sectors) that end with an error condition should have the address of the first sect or in error in the command block registers. device control register this register is used to control the compactflash storage card interrupt request and to issue an ata soft reset to the card. this register can be written even if the device is busy. the bits are defined as follows: d7 d6 d5 d4 d3 d2 d1 d0 x x x x 1 sw rst -ien 0 bit 7 : this bit is an x (don?t care). bit 6 : this bit is an x (don?t care). bit 5 : this bit is an x (don?t care). bit 4 : this bit is an x (don?t care). bit 3 : this bit is ignored by the compactflash storage card. bit 2 (sw rst) : this bit is set to 1 in order to force t he compactflash storage card to perform an at disk controller soft reset operation. this does not change the pcmcia card configuration registers (4.3.2 to 4.3.5) as a hardware re set does. the card remains reset until this bit is reset to ?0.? bit 1 (-ien) : the interrupt enable bit enables interrupts when the bit is 0. when the bit is 1, interrupts from the compactflash storage card are disabled. th is bit also controls the int bit in the configuration and status r egister. this bit is set to 0 at power on and reset. bit 0 : this bit is ignored by the compactflash storage card.
hanbit HFDOM40MRXXX url:www.hbe.co.kr 10 / 10 hanbit electronics co., ltd. rev. 1.0 (november. 2003) card address register this register is provided for compatibility with the at disk drive interface. it is recommended that this register not be mapped into the host? s i/o space because of potential conflic ts on bit 7. the bits are defined as follows: d7 d6 d5 d4 d3 d2 d1 d0 x -wtg -hs3 -hs2 -hs1 -hs0 -nds1 -nds0 bit 7 : this bit is reserved. implementation note: conflicts may occur on the host data bus when this bit is provided by a floppy disk controller operating at the same addresses as the compactf lash storage card. following are some possible solutions to this problem for the pcmcia implementation: 1) locate the compactflash storage card at a non- conflicting address, i.e. secondary address (377) or in an independently decoded address space when a floppy disk controller is located at the primary addresses. 2) do not install a floppy and a compactflash stor age card in the system at the same time. 3) implement a socket adapter which can be programmed to (conditionally) tri-state d7 of i/0 address 3f7h/377h when a compactflash storage card is installed and conversely to tri-state d6-d0 of i/o addresses 3f7h/377h when a floppy controller is installed. 4) do not use the compactflash storage card?s dr ive address register. this may be accomplished by either a) if possible, program the host adapt er to enable only i/o addresses 1f0h-1f7h, 3f6h (or 170h-177h, 176h) to the compactflash storage card or b) if provided use an additional primary / secondary configuration in the compactflash st orage card which does not respond to accesses to i/o locations 3f7h and 377h. with either of thes e implementations, the host software must not attempt to use information in the drive address register. bit 6 (-wtg) : this bit is 0 when a write operation is in progress, otherwise, it is 1. bit 5 (-hs3) : this bit is the negation of bi t 3 in the drive/head register. bit 4 (-hs2) : this bit is the negation of bi t 2 in the drive/head register. bit 3 (-hs1) : this bit is the negation of bi t 1 in the drive/head register. bit 2 (-hs0) : this bit is the negation of bi t 0 in the drive/head register. bit 1 (-nds1) : this bit is 0 when drive 1 is active and selected. bit 0 (-nds0) : this bit is 0 when the drive 0 is active and selected.
hanbit HFDOM40MRXXX url:www.hbe.co.kr 11 / 11 hanbit electronics co., ltd. rev. 1.0 (november. 2003) data register the data register is a 16-bit register, and it is used to transfer data blocks between the compactflash storage card data buffer and the host. th is register overlaps the error r egister. the table below describes the combinations of data register access and is provided to assist in understanding the overlapped data register and error/feature register rather than to attempt to def ine general pcmcia word and byte access modes and operations. see the pcmcia pc card standard release 2.0 for def initions of the card accessing modes for i/o and memory cycles. 15 14 13 12 11 10 9 8 data (15:8) 7 6 5 4 3 2 1 0 data (7:0) feature register this register provides informati on regarding features of the compactflash storage card that the host can utilize. this register is also access ed on data bits d15-d8 during a write operation to offset 0 with -ce2 low and -ce1 high. 7 6 5 4 3 2 1 0 command specific sector count register this register contains the number s of sectors of data requested to be transferred on a read or write operation between the host and t he compactflash storage card. if the va lue in this register is zero, a count of 256 sectors is specified. if the command was successful, this register is zero at command completion. if not successfully comp leted, the register contains t he number of sectors that need to be transferred in order to complete the request. 7 6 5 4 3 2 1 0 sector count
hanbit HFDOM40MRXXX url:www.hbe.co.kr 12 / 12 hanbit electronics co., ltd. rev. 1.0 (november. 2003) sector number register this register contains the starti ng sector number or bits 7-0 of t he logical block address (lba) for any compactflash storage card data access for the subsequent command. bit description ----- chs 7 6 5 4 3 2 1 0 sector (7:0) lba 7 6 5 4 3 2 1 0 lba (15:8) cylinder low register this register contains the low order 8 bits of the starting cylinder addre ss or bits 15-8 of the logical block address. bit description----- chs 7 6 5 4 3 2 1 0 cylinder (7:0) lba 7 6 5 4 3 2 1 0 lba (15:8) cylinder high register this register contains the high order bits of the starting cylinder addre ss or bits 23-16 of the logical block address. bit description - chs 7 6 5 4 3 2 1 0 cylinder (7:0) lba 7 6 5 4 3 2 1 0 lba (15:8)
hanbit HFDOM40MRXXX url:www.hbe.co.kr 13 / 13 hanbit electronics co., ltd. rev. 1.0 (november. 2003) 3. interface bus timing access spcifications true ide mode i/o read timing table 3.1 true ide read timing
hanbit HFDOM40MRXXX url:www.hbe.co.kr 14 / 14 hanbit electronics co., ltd. rev. 1.0 (november. 2003) true ide mode i/o write timing table 3.2 true ide write timing
hanbit HFDOM40MRXXX url:www.hbe.co.kr 15 / 15 hanbit electronics co., ltd. rev. 1.0 (november. 2003) ordering infomation no parts capacity media transfer mode chip number operation mode 1 dom40mr016 16mbyte byte 1 true ide 2 dom40mr032 32mbyte byte 1 true ide 3 dom40mr064 64mbyte byte 1 true ide 4 dom40mr128 128mbyte byte 1 true ide 5 dom40mr256 256mbyte byte 1 true ide 6 dom40mr512 512mbyte byte 4 true ide 7 dom40mr16 1gbyte byte 4 true ide 8 dom40mr16 1gbyte byte 4 true ide
hanbit HFDOM40MRXXX url:www.hbe.co.kr 16 / 16 hanbit electronics co., ltd. rev. 1.0 (november. 2003) packaging < view from front side > figure 1.1 40 pin type flash disk module dimensions top-connector attach top side bottom side 1 2 39 40 123 top side bottom-connector attach 1 2 39 40 top side bottom side bottom side jumper master slave 1,2 close 2,3 close 55.50??0.1mm 30.50??0.2mm 1 23 1 2 39 40 7.50mm 8.90mm??0.1mm 1.4mm??0.1mm

▲Up To Search▲

Price & Availability of HFDOM40MRXXX

	To Download HFDOM40MRXXX Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .