rev. 8.31.09_89 mp series 1 of 8 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 embedded power for business-critical continuity electrical specifications input input r ange: 85 - 264 vac 120 - 350 vdc frequency: 47 - 440 hz inrush current: 40 a peak max. (soft start) efficiency: 70 - 80% typ. @ full case load power factor: 0.99 typ. meets en61000-3-2 turn-on time: ac on 1.5 sec typ. inhibit/enable 150 ms typ. emi filter standard: cispr 22/en55022 level b emi filter (low leakage option): cispr 22/en55022 level a leakage current standard: 2.0 ma max. @240 vac leakage current (low leak - age option): 300a max. @ 240 vac radiated emi: cispr 22/en55022 level b holdover storage: 20 ms minimum (independent of input vac) ac ok: >5 ms early warning min. before outputs lose regulation full cycle ride thru (50 hz) harmonic distortion: meets en61000-3-2 isolation: meets en60950 global inhibit/enable: ttl, logic 1 and logic 0 input fuse (internal): mp4: 10 a; mp6: 15 a; MP8: 20 a; mp1: 20 a warranty: 2 years mp series 400 - 1200 watts special features ? current share on all outputs with ratings of 10 a or greater ? remote sense on all outputs with ratings greater than 2 a ? overload protection on all outputs ? voltage adjustment on all outputs ? margining on all single output modules ? input ok signal and status indicator led ? global dc ok signal and status indicator led ? global and individual module inhibits/ enable ? 2 year warranty ? forced air cooling, field replaceable fan ? isolated 5 v bias voltage ? power factor correction ? en61000-3-2 harmonic distortion compliance ? cispr 22, en55022 curve b conducted / radiated emi ? european ce mark requirements ? optional vme timing and system dc ok module ? customer-provided air option ? additional 200 w output @ high line (180-264 vac) ? low leakage option for medical applications ? en61000 immunity standards ? standard modification flexibility (consult factory) low noise fan fan fail signal module enable outputs down to 0.5v total power: 400 - 1200 watts input voltage: 85 - 264 vac 120 - 350 vdc # of outputs: up to 21 safety ul ul1950 csa csa22.2 no. 234 level 5 iec iec950, class 1 vde en60950, babt compliance to en 60950, bs 7002 cb certificate and report ce mark ? ? ? ? ? ? ?
rev. 8.31.09_89 mp series of 8 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 module type single single single dual triple output 1 1 2 3 max output power 210 w 360 w 600 w 144 w 36 w max output current 35 a 60 a 120 a 10 a 2 a volts 2-60 v 2-60 v 2-60 v 2-28 v 2-28v standard voltage increments 25 25 25 19 18 remote sense on outputs yes yes yes yes, both no remote margin/v-program yes yes yes no no module inhibit (isolated) yes yes yes -- -- single wire active current share yes yes yes yes, main only -- over voltage / over current protection yes yes yes yes over current minimum load required no no no yes (10%) main only no slots occupied in any mp case 1 2 3 1 1 output module line-up operating temperature: -20 c to 50 c (start @ 0 c) (derate each output linearly to 50% at 70 c) (-20 c to 40 c max. with rear air option) shock/vibration: mil-hdbk 810e humidity: 95% non-condensing storage temperature: -40 c to 85 c temperature coefficient: 0.02% per c cooling: internal dc fan or customer provided air (option) environmental specifications output adjustment range: 10% minimum all outputs margining: 4 - 6% nominal 1 overall regulation: 0.4% or 20mv max. (36 w modules 4% maximum) ripple: rms: 0.1% or 10mv, whichever is greater pk-pk: 1.0% or 50mv, whichever is greater bandwidth limited to 20 mhz dynamic response: < 2% or 100 mv, with 25% load step recovery time: to within 1% in < 300 sec overcurrent protection:** single output module & main output of dual output module 105-120% of rated output current. aux output of dual output module 105- 140% of rated output current short-circuit protection: protected for continuous short-circuit recovery auto upon removal of short overvoltage protection: (measured at sense connection) single output module: 2-5.5 v 122-134% ; 6-60 v 100-120% dual output module: 2-6 v 122-134% ; 8-28 v 110-120% triple output module: no overvoltage protection provided. recycle ac input voltage to reset ovp circuit reverse voltage protection: 100% of rated output current output (cont.) thermal protection: all outputs disabled when internal temp exceeds safe operating range. > 5ms warning (ac ok signal) before shutdown remote sense: up to 0.5 v total drop (not avbl on triple output module) single wire parallel: current share to within 2% of total rated current 2 dc ok: -2% to -8% of nominal for any monitored output 2 minimum load: not required on single or triple output. 10% required on main of dual output 3 housekeeping bias voltage: 5 vdc @ 1.0 a max. present whenever ac input is applied module inhibit: ttl, isolated, singles and dual (both outputs) only switching frequency: 250k hz output/output isolation: >1 megohm vme signal option board: por signal & quad external dc ok hold-up module (hup): 1-slot module providing additional 34msec (60msec total); hold-up @ 600 w loading. 1. single output modules only. 2. single and main of dual output modules only 3. contact factory for optional preload if required field demonstrated mtbf: > 550,000 hours at full load, 220 vac and 25 c ambient conditions
rev. 8.31.09_89 mp series 3 of 8 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 voltage voltage code single output module code dual output** triple output 1 2 3 v1 v2 v1 v2 v3 2 v a 35 a 60 a 120 a 10 a 2 a 2.2 v b 35 a 60 a 120 a 10 a 2 a 3 v c 35 a 60 a 120 a 10 a 2 a 3.3 v d 35 a 60 a 120 a 10 a 2 a 5 v e 35 a 60 a 120 a 10 a 10 a 2 a 5.2 v f 35 a 60 a 115 a 10 a 2 a 5.5 v g 34 a 58 a 109 a 10 a 2 a 6.0 v h 23 a 42 a 78 a 10 a 2 a 8.0 v i 20 a 36 a 68 a 1 a 1 a 1 a 10 v j 18 a 32 a 60 a 1 a 1 a 1 a 11 v k 17 a 31 a 54.5 a 1 a 1 a 1 a 12 v l 17 a 30 a 50 a 10 a 4 a 1 a 1 a 1 a 14 v m 14 a 21 a 40.5 a 9 a 4 a 1 a 1 a 1 a 15 v n 14 a 20 a 39 a 8 a 4 a 1 a 1 a 1 a 18 v o 11 a 19 a 33.3 a 0.5 a 0.5 a 20 v p 10.5 a 18 a 30 a 0.5 a 0.5 a 24 v q 8.5 a 15 a 23.5 a 4 a 2 a 0.5 a 0.5 a 28 v r 6.7 a 12.8 a 21.4 a 3 a 2 a 0.5 a 0.5 a 30 v s 6.5 a 12 a 20 a 33 v t 6.2 a 10.9 a 18.2 a 36 v u 5.8 a 10 a 16.6 a 42 v v 4.2 a 7.5 a 12.5 a 48 v w 4.0 a 7.5 a 12.5 a 54 v x 3.7 a 6.0 a 11 a 60 v y 3.5 a 6.0 a 10 a non-std* z special voltage - consult factory for specifications 2.4 v -2.7 v 35 a 60 a 120 a 10 a 2 a 3.6 v - 4.5 v 35 a 60 a 120 a 10 a 2 a 6.6 v -9.2 v 20 a 36 a 68 a 10 a 4 a 1 a 8.8 v - 9.0 v 18 a 32 a 60 a 10 a 4 a 1 a output module voltage/current mp 1 - 3l - 2e - 1q - 4ll - hup - 00 - ### case size (mm) 4 = 2.5 x 5 x 10; 400 w-600 w, 5 slots (63.5 x 127 x 254) 6 = 2.5 x 5 x 11; 600 w-800 w, 5 slots (63.5 x 127 x 279.4) 8 = 2.5 x 7 x 10; 800 w-1000 w, 6 slots (63.5 x 177.8 x 254) 1 = 2.5 x 8 x 11; 1000 w-1200 w, 7 slots* (63.5 x 203.2 x 279.4) module codes module/voltage/option codes module codes: (none) = 36 w triple o/p (1 slot) 1 = 210 w single o/p (1 slot) 2 = 360 w single o/p (2 slot) 3 = 750 w single o/p (3 slot) 4 = 144 w dual o/p (1 slot) 5 - 9 = future case option codes first digit 0 - 9 = parallel code (see parallel codes table above) second digit standard options 0 = no options 1 = rear air exhaust 3 = global enable 5 = opt 1 + opt 3 m = low leakage n = low leakage + opt 1 p = low leakage + opt 3 r = low leakage + opt 5 add-on modules voltage codes: see output module voltage/ current table above module/voltage/option codes first - module code second - voltage code case option codes hup = hold up module vme = vme por signal and isolated dc case size factory assigned for modifications hardware code ordering information 7 6 5 4 3 2 1 mp4 & mp6 available slots MP8 available slots slot 1 slot 2 slot 3 slot 4 slot 5 slot 1 slot 2 slot 3 slot 4 slot 5 slot 6 slot 1 slot 2 slot 3 slot 4 slot 6 slot 7 slot 5 mp1 available slots parallel codes 0 = no parallel 1 = 1 & 2 2 = 2 & 3 3 = 3 & 4 4 = 4 & 5 5 = 3 & 4 & 5 6 = 5 & 6 7 = 4 & 5 & 6 8 = 6 & 7 9 = 3 & 4, 6 & 7 notes: 1. omit digits that do not apply. 2. specify modules from lowest number of outputs to highest. (single/dual/triple) 3. if number of outputs are equal, specify modules from highest to lowest power increments. if power increments are equal, specify in descending alphabetical order (1a, b, c . . .). 4. always start with slot 1. 5. all mp model configurations created using this selection guide are standard mp products with standard availability and lead times. 6. optional vme/dcok module must always be located in the last slot. module designator is vme.
rev. 8.31.09_89 mp series of 8 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 input 85-264 vac 180-264 vac mp 8 = 2.5 x 7 x 10 6 available slots 800 w max. 1000 w max. (63.5 x 177.8 x 254mm) output module area ac input s l o t 6 s l o t 5 s l o t 4 s l o t 3 s l o t 2 s l o t 1 177.8 7.0 -a - (4 pl) + + - + - + - non -cumula tive 4.3 .8 .17 .03 23.9 .5 .94 .02 s ? l ? o ? t s ? l ? o ? t s ? l ? o ? t s ? l ? o ? t s ? l ? o ? t 5 4 3 2 1 mp4 & mp6 MP8 single pfc input connector j1 control connector standard for all cases pin no. function j1-1 input ac ok - emitter j1-2 input ac ok - collector j1-3 global dc ok - emitter j1-4 global dc ok - collector j1-5 spare j1-6 global inhibit/optional enable logic 0 j1-7 global inhibit/optional enable logic 1 j1-8 global inhibit/optional enable return j1-9 selv 5 v housekeeping j1-10 se:v 5 v housekeeping return mates with molex 90142-0010 housing 90119-2110 pin figure 1. connector j1 input 85-264 vac 180-264 vac mp 4 = 2.5 x 5 x 10 5 available slots 400 w max. 600 w max. (63.5 x 127 x 254mm) mp 6 = 2.5 x 8 x 11 5 available slots 600 w max. 800 w max. (63.5 x 127 x 279.4mm) 210 w 360 w 600 w 144 w pin connectors triple dual 36 w input 85-264 vac 180-264 vac mp 1 = 2.5 x 8 x 11 7 available slots 1000 w max. 1200 w max. (63.5 x 203.2 x 279.4mm) mp1
rev. 8.31.09_89 mp series of 8 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 dc-dc converter output modules pin 1 v+ m4x8 screws (4x) v- v adj .32 (8.1) .44 (11.3) (2x) (2x) .33 (8.5) .63 (16.0) .48 (12.1) 1.38 (35.1) pin 1 v2 ad j .32 (8.1) .42 (10.7) v1 + v1 - v2 - v2 + m3x8 scre ws (4x) .46 (11.7) (4x) .30 (7.5) (3x) v1 ad j 1.17 (29.7) single 210 watt dual 144 watt single 360 watt single 600 watt mp modules mechanical drawings triple 36 watt v2 adj v1 adj pin 1 v3 adj dc output connection .48 (12.1) .84 (21.3) m4x8 screws (4x) v- pin 1 v adj v+ .44 ? (11.3) .32 ? (8.1) 1.24 (31.6) (2x) .61 (15.6) (2x) .63 ? (16.0) .59 ? (15.0) v1 + v1 - v2 + v2 - v3 + v3 - figure 1. ac inpu t 1 2 3 ~ n 6 1 10 5 fi gu re 2. connector j 1 mates with molex 90142-0010 housing 90119-2110 pin figure 4. connector j1 pfc input connector pin no. function 1 + remote sense single or dual o/p main 2 remote margin / v. program single o/p 3 margin high single o/p 4 - remote sense/margin low single or dual o/p main 5 spare 6 module, isolated inhibit single or dual o/p 7 module inhibit return single or dual o/p 8 current share (swp) single or dual o/p main 9 + remote sense v2 dual o/p, single is spare 10 - remote sense v2 dual o/p, single is spare pin 1 .32 ? (8.1) .44 (11.2 ) (2x) v+ m4x8 screws (2x) v- v adj .48 (12.1) .44 (11.3) 1.38 ? (35.1)
rev. 8.31.09_89 mp series of 8 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 notes 1. input: barrier type. three no. 6-32 b.h. screws (0.375 centers). max torque: 6 in-lbs. (0.67 n-m). 2. control connectors: (j1 and j2) 10 position housing, gold plated contacts. mates with molex 90142-0010 housing with 90119-2110 crimp contacts (molex c - grid iii series). connector kit includes mating connector and 10 pins, astec part #70-841-004. 3. chassis material: aluminum with chemical film coating (conductive). 4. all dimensions are in millimeters and inches, and are typical. 5. customer mounting -3 sides m4, bottom also includes 8-32 mounting holes. max. penetration is 0.150 (3.8 mm). max. torque: 5 in-lbs. 6. output module connections: all single o/p modules are m4 x 8mm screws. max. torque: 10 in-lbs. dual o/p module is m3 x 8mm screws. max. torque: 5 in-lbs. triple o/p module is .045 square pins on .156 centers. mates with moelx 09-50-8063 or equivalent. mp series mp4 (400/600 watts max) mp6 (600/800 watts max) 5-inch case size: mp4: 2.5 x 5 x 10 (63.5mm x 127mm x 254mm) 5-inch case size: mp6: 2.5 x 5 x 11 (63.5mm x 127mm x 279.4mm) weight: mp4 case: 2.6 lbs. ? mp6 case: 3.2 lbs. ? 36 w triple: 0.5 lb. ? 210 w single: 0.6 lb. ? 360 w single: 1.0 lb. ?600 w single: 2.0 lbs ?144 w dual: 0.6 lb 19.05 .750 171.45 6.750 29.05 1.144 171.45 6.750 a a a b b b b m4 mtg holes 4 pl marked "b" #8-32 mtg holes 4 pl marked "a" 101.60 4.000 12.70 .500 standard airflow +.0 -.5 127.0 +.00 -.02 5.00 2 19.0 .75 49.2 1.94 1 + - + - +. 0 -. 5 254.0 +.00 -.02 10.00 3. 7 .1 5 typ 19.05 .750 +.0 -. 5 63.5 +.00 -.02 2.50 3. 5 .1 4 (typ ) m4 mtg holes 4 pl mounting holes dimensions identica l on both sides 17.3 1. 0 .68 .04 171.4 5 6.750 38.1 0 1.50 0 12.7 0 .500 mp4 +.0 -. 5 279. 4 +.00 -.02 11 .00 mp6
rev. 8.31.09_89 mp series of 8 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 mp series MP8 (800/1000 watts max) 7-inch case size: MP8: 2.5 x 7 x 10 (63.5mm x 177.8mm x 254mm) weight: MP8 case: 4.1 lbs. ? 36 w triple: 0.5 lb. ? 210 w single: 0.6 lb. ? 360 w single: 1.0 lb. ? 600 w single: 2.6 lbs. ? 144 w dual: 0.6 lb. notes 1. input: barrier type. three no. 6-32 b.h. screws (0.375 centers). max torque: 6 in-lbs. (0.67 n-m). 2. control connectors: (j1 and j2) 10 position housing, gold plated contacts. mates with molex 90142-0010 housing with 90119-2110 crimp contacts (molex c - grid iii series). connector kit includes mating connector and 10 pins, astec part #70-841-004. 3. chassis material: aluminum with chemical film coating (conductive). 4. all dimensions are in millimeters and inches, and are typical. 5. customer mounting -3 sides m4, bottom also includes 8-32 mounting holes. max. penetration is 0.150 (3.8 mm). max. torque: 5 in-lbs. 6. output module connections: all single o/p modules are m4 x 8mm screws. max. torque: 10 in-lbs. dual o/p module is m3 x 8mm screws. max. torque: 5 in-lbs. triple o/p module is .045 square pins on .156 centers. mates with moelx 09-50-8063 or equivalent. 19.05 0.75 171.45 6.75 29.05 1.1 171.45 6.75 12.70 0.5 m4 moun ting ho l es #8-32 mount ing ho l es mar ked "a" (4x) "a" "a" "a" "a" "b" "b" mar ked "b" (4x) "b" "b" 152.40 6.0 254 10.0 standard airflow 59.5 2.34 60.5 2.38 14.0 0.55 14.7 0.58 31.8 1.25 177.8 7.0 63.5 2.5 2 m4 mount ing holes (4x) 171.45 6.75 19.05 0.7 38.10 1.5 35.0 1.38 12.70 0.5 254 10.0 63.5 2.5
rev. 8.31.09 series 8 of 8 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 americas 5810 van allen way carlsbad, ca 92008 usa telephone: +1 760 930 4600 facsimile: +1 760 930 0698 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom telephone: +44 (0) 1384 842 211 facsimile: +44 (0) 1384 843 355 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong telephone: +852 2176 3333 facsimile: +852 2176 3888 for global contact, visit: www.powerconversion.com techsupport.embeddedpower @emerson.com while every precaution has been taken to ensure accuracy and completeness in this literature, emerson network power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. emerson network power and the emerson network power logo are trademarks and service marks of emerson electric co. ?2009 emerson electric co. emersonnetworkpower.com embedded computing embedded power monitoring outside plant power switching & controls precision cooling racks & integrated cabinets services surge protection emerson network power. the global leader in enabling business-critical continuity. ac power connectivity dc power 8-inch case size: mp1: 2.5 x 8 x 11 (63.5mm x 203.2mm x 279.4mm) weight: mp1 case: 5.0 lbs. ?36 w triple: 0.5 lb. ? 210 w single: 0.6 lb. ? 360 w single: 1.0 lb. ? 600 w single: 2.0 lbs. ? 144 w dual: 0.6 lb. notes 1. input: barrier type. three no. 6-32 b.h. screws (0.375 centers). max torque: 6 in-lbs (0.67 n-m). 2. control connectors: (j1 and j2) 10 position housing, gold plated contacts. mates with molex 90142-0010 housing with 90119-2110 crimp contacts (molex c - grid iii series). connector kit includes mating connector and 10 pins, astec part #70- 841-004. 3. chassis material: aluminum with chemical film coating (conductive). 4. all dimensions are in millimeters and inches, and are typical. 5. customer mounting -3 sides m4, bottom also includes 8-32 mounting holes. max. penetration is 0.150 (3.8 mm). max. torque: 5 in-lbs. 6. output module connections: all single o/p modules are m4 x 8mm screws. max. torque: 10 in-lbs. dual o/p module is m3 x 8mm screws. max. torque: 5 in-lbs. triple o/p module is .045 square pins on .156 centers. mates with molex 09-50-8063 or equivalent. mp series mp1 (1000/1200 watts max) 171.45 6.750 171.45 6.750 19.05 .750 177.80 7.000 29.05 1.144 12.70 .500 bo tt om mounting sur fa ce m4 mt g holes 4 pl marked ?b ? std air fl ow #8-32 mt g holes 4 pl marked ?a? 203.2 8.00 2 31.8 1.25 76.2 3.00 69.9 2.75 14.0 .55 14.7 .58 171.45 6.750 38.10 1.500 12.70 .500 279.4 11.00 35.0 1.38 19.05 .750 16.50 6.50 63.5 2.50 m4 mt g holes 4 pl mounting holes - dimensions identical on bo th sides
|
