GP1FJ100RP GP1FJ100RP outline dimensions (unit : mm) thin low voltage operation type optical mini-jack for digital audio equipment 1. md players 2. portable cd players (optic receiver part) features applications 1. thin type fiber optic receiver ( 2.5mm) 2. both optical and electrical signal can be received 3. built-in shutdown function (comsumption current at shutdown mode:max. 1 a) 4. low voltage operation (v cc 1.5 to 3.6v) 5. high speed data transmission (signal transmission speed : max, 8mb/s (nrz signal)) parameter symbol rating unit supply voltage v cc ma operating temperature storage temperature soldering temperature (reflow) t opr t stg t sol i oh 1 (source current) ma i ol 1 (sink current) c v c c ? 0.5 to + 5.5 ? 20 to + 70 ? 30 to + 80 240 output current (t a = 25 c) *1 for 10s *2 for 3.5s (2 times or less) *1 hand soldering temperature t osl c 355 *2 ? ?pic?optical ic) is a trademark of the sharp corporation. an opic consists of a light-detecting element and signal- processing circuit integrated onto a signal chip. 9 10 11 12 gnd v out sd v cc internal equivalent circuit (device) opic light detector 4-0.4 ? 1 1 ? 1 2 ? 1 2 ? 1 1 1 max. 0.4 max. 1 1 1 7-0.8 1.2 1.2 6.6 max. 3.6 max. 3.3 1.2 4.3 2.8 3.2 5.1 3.2 4.3 (0.9) (1.0) (0.9) (2.2) 1.5 0.1 5 0.1 2.5 0.1 3.5 0.1 11.1 + 0.2 ? 0.1 2- 1 0.1 2- 1.2 (hole) 5.2 0.1 2.6 0.05 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 9 10 11 12 9 10 11 12 jack terminal arrangement device terminal arrangement 1.4 0.15 ? 1 terminal root shutdown circuit 1 2 3 4 5 ? ? ? ? ? ? ? ? ? jack terminal 6 7 8 9 10 11 12 ? ? ? ? ? device terminal jack body 1 2 3 4 5 6 7 2.7 2.7 1.6 4-0.6 4-0.35 11 22 1 1 1.05 1.2 3.2 3.2 5 5.1 8.6 4-1.8 2.5 1.2 7-1.6 2.2 (land) example of pcb pattern drawing (top view) ? unspecified tolerance: 0.3mm ? ( ) : reference dimensions ? if portion contacts with patterns or circuits,there is possibility that each jack terminal will short parameter symbol rating unit total power dissipation ? operating temperature storage temperature soldering temperature (reflow) a.c. 500v rms c ? c c d.c. 12v, 1a ? 20 to + 70 ? 30 to + 80 240 isolation voltage *3 *1 t osl c 355 *2 hand soldering temperature p tot t opr t stg t sol v iso *2 *3 for 1minute absolute maximum ratings(jack) absolute maximum ratings (photoelectric conversion element) notice in the absence of confirmation by device specification sheets, sharp takes no responsibility for any defects that may occ ur in equipment using any sharp devices shown in catalogs, data books, etc. contact sharp in order to obtain the latest device specification sheets before usin g any sharp device. internet internet address for electronic components group http://sharp-world.com/ecg/
parameter symbol min. typ. max. unit peak sensitivity wavelength dissipation current high level output voltage ? ? ? low level output voltage conditions ??????????????????????? refer to fig.1 refer to fig.3 refer to fig.3 refer to fig.3 refer to fig.3 refer to fig.3 refer to fig.3 refer to fig.3 refer to fig.4, p c =? 14.5dbm refer to fig.4, p c =? 27dbm 3ma ? low high delay time fall time rise time high low delay time pulse width distortion jitter ? ? ? ? 20 v cc 0.8 ? 7 ? 660 2 consumption current at shutdown mode p t phl i cc t plh v oh v ol t r t f ? t w ? t j i sc (sd) refer to fig.2 1 a ?? ? ? 7 ? ? ? 30 30 130 130 + 20 v cc 0.2 30 30 ns ? ? ? ? ns nm v ns ns v ns ns ns (t a = 25 c, v cc = 2.4v) GP1FJ100RP mechanical and electrical characteristics(jack) electro-optical characteristics parameter symbol min. typ. max. unit insertion force, with drawal force contact resistance isolation resistance f p 35 r con r iso conditions *4 *5 d.c. 500v, 1minute 30 m ? ? 3 ? 100 ? ? ? n m ? note) this jack is designed for applicable to 2.5 compact single head plug (jis c6560) *4 measuring method of insertion force and withdrawal force insertion and withdrawal force shall be measured after inserting and withdrawing 3 times by using jis c6560 standard plug for t est *5 measuring method of contact resistance it measures at 100ma or less and 1 000hz at the condition of inserting jis c6560 standard plug for test in which movable contac t terminal and make contacts are described fig.1 dissipation current v cc v cc gnd v in v out sd gnd v cc a ammeter input measuring method v cc = 2.4v measured on an ammeter (dc average amperage) p c =? 14.5dbm 6mb/s nrz, duty 50% or 3mb/s biphase mark prbs signal input conditions optical output coupling with fiber standard transmitter input signal supply voltage standard transmitter GP1FJ100RP unit to be measured fiber optic cable parameter symbol unit operating supply voltage v cc operating transfer rate receiver input optical power level t p c mb/s v dbm max. 8 3.6 ? 14.5 typ. ? 2.4 ? min. 0.1 1.5 ? 27.0 recommended operating conditions
GP1FJ100RP fig.3 measuring method of output voltage and pulse response fig.2 measuring method of consumption current at shutdown mode sd standard transmitter fiber optic cable GP1FJ100RP unit to be measured v cc v cc gnd v in v out gnd v cc input 6mb/s nrz, duty 50% ch1 ch2 tektronix 7834 or 7934 type oscilloscope t r t plh t phl t f 50% 90% v oh v ol 50% 10% standard transmitter input signal (ch1) GP1FJ100RP output signal (ch2) test item symbol low high pulse delay time t plh high low pulse delay time t phl rise time t r fall time t f pulse width distortion ? t w = t phl ? t plh ? t w test item notes (1) v cc = 2.4v (state of operating) (2) the fiber coupling light output set at ? 14.5dbm/ ? 27dbm (3) the probe for the oscilloscope must be more than 1m ? and less than 10pf (4) the output (h/l level) of GP1FJ100RP are not fixed constantly when it receives the modulating light (including dc light, no input light) less than 0.1mb/s v cc v cc gnd v in v out sd gnd v cc a ammeter input standard transmitter GP1FJ100RP unit to be measured fiber optic cable when shutdown terminal (sd terminal) receives an high level signal, it becomes to shutdown mode v out output is low level at shutdown mode
GP1FJ100RP fig.4 measuring method of jitter input signal 50% GP1FJ100RP output 50% tektronix7834 or 7934 type trigger:ch1 storage mode sweep:auto/norm ch1 ch2 oscilloscope input signal 3mb/s biphase prbs signal ? t j ? t j standard transmitter fiber optic cable GP1FJ100RP unit to be measured v cc v cc gnd v in v out gnd v cc input test item test condition jitter set the trigger on the rise of input signal to measure the jitter of the rise of output jitter symbol ? t j ? t j set the trigger on the fall of input signal to measure the jitter of the fall of output test item notes (1) the fiber coupling light output set at ? 14.5dbm/ ? 27dbm (2) the waveform write time shall be 3 seconds. but do not allow the waveform to be distorted by increasing the brightness too much (3) v cc = 2.4v (state of operating) (4) the probe for the oscilloscope must be more than 1m ? and less than 10pf
notice the circuit application examples in this publication are provided to explain representative applications of sharp devices and are not intended to guarantee any circuit design or license any intellectual property rights. sharp takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of sharp's devices. contact sharp in order to obtain the latest device specification sheets before using any sharp device. sharp reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. manufacturing locations are also subject to change without notice. observe the following points when using any devices in this publication. sharp takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) the devices in this publication are designed for use in general electronic equipment designs such as: - - - personal computers - - - office automation equipment - - - telecommunication equipment [terminal] - - - test and measurement equipment - - - industrial control - - - audio visual equipment - - - consumer electronics (ii) measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when sharp devices are used for or in connection with equipment that requires higher reliability such as: - - - transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) - - - traffic signals - - - gas leakage sensor breakers - - - alarm equipment - - - various safety devices, etc. (iii)sharp devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: - - - space applications - - - telecommunication equipment [trunk lines] - - - nuclear power control equipment - - - medical and other life support equipment (e.g., scuba). if the sharp devices listed in this publication fall within the scope of strategic products described in the foreign exchange and foreign trade law of japan, it is necessary to obtain approval to export such sharp devices. this publication is the proprietary product of sharp and is copyrighted, with all rights reserved. under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of sharp. express written permission is also required before any use of this publication may be made by a third party. contact and consult with a sharp representative if there are any questions about the contents of this publication.
|
