View S6D0114_3250454.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

preliminary 132 rgb x 176 dot 1-chip driver ic with internal gram for 262,144 colors tft-lcd july 3, 2002 ver. 0 . 0 prepared by: minseok song tempest0@samsung.com contents in this document are subject to change without notice. no part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of lcd driver ic team. s6d 0 114
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 2 S6D0114 specification revision history version content author date 0 .0 original m. s. song july 3 , 2002
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 3 introduction the S6D0114 is 1-chip solution for tft-lcd panel: source driver with built-in memory, gate driver, power ic are integrated on one chip. this ic can display to a maximum of 132-rgb x 176-dot graphics on 2 6 0 k-color tft panel. the S6D0114 also supports bit-operation functions, 18-/16-/9-/8-bit high-speed bus interface and high-speed ram-write functions enable efficient data transfer and high-speed rewriting of data to the internal gram. the moving picture area can be specified in internal gram by window function. the specified window area can be updated selectively, so that moving picture is able to be displayed simultaneously independent of still picture area. the S6D0114 has various functions for reducing the power consumption of a lcd system: operating at low voltage (minimum 1.8v), register-controlled power-save mode, partial display mode and so on. the ic has internal gram to store 132- rgb x 176 -dot 260k-color image and internal booster that generates the lcd driving voltage, b r eeder resistance and the voltage follower circuit for lcd driver. this lsi is suitable for any medium-sized or small portable mobile solution requiring long-term driving capabilities, such as digital cellular phones supporting a web browser, bi - directional pagers, and small pdas.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 4 features 132 - rgb x 176 -dot tft- lcd display controller/driver ic for 2 6 2,144 colors ( 396ch-source driver/176ch-gate driver) 18-/16-/9-/8-bit high-speed parallel bus interface (80- and 68- system) and serial peripheral interface ( spi) high-speed ram write function (transfer 4-word at a time) writing to a window-ram address area by using a window-address function bit-operation function for graphic processing - write-data mask functions in bit unit s - logical operation in pixel unit and conditional write function various color-display control function s - 262,144 colors can be displayed at the same time (including gamma adjust) - vertical scroll display function in raster-row units internal ram capacity: 132 x 18 x 176 = 418,176 b it s low -power operati on su pports : - power-save mode: standby mode , sleep mode - partial display of two screens in any position - maximum 12-time step-up circuit for generating driving voltage - voltage followers to decrease direct current flow in the lcd drive breeder-resistors - equalizing function for the switching performance of step-up circuits and operational amplifiers n -raster row inversion drive ( r everse the polar ity of driving voltage in every selected raster row ) internal oscillation circuit and external hardware reset structure for tft-display retention volume (cst/cadd structure) alternating functions for tft-lcd counter-electrode power - n-line alternating drive of vcom (vgoff is also available for n-line alternating drive for cadd) internal p ower supply ci rcuit - step-up circuit: five to nine times, positive-polarity inversion - adjustment of vcom(vgoff) amplitude: internal 22-level digital potentiometer o perati ng voltage apply voltage - vdd to vss = 1. 8 to 2.5 v (non-regulating) (logic voltage ra nge ? non-regulated ) vdd3 to vss = 2.3 to 3.3 v (regulating) (logic voltage range ? regulated) - v ci to vss = 2.5 to 3.3 v ( internal reference power-supply volt age) - vci1 to vss = 1.7 to 2.75 v (2.5 x 0.68 ~ 2.75) (power supply for step-u p circuits) generate voltage - for the source driver: avdd to vss = 3.5 to 5.5v (power supply for driving circuits) gvdd to vss = 3.0 to 5.0v (reference power supply for grayscale voltages) - for the gate driver: vgh to vgl = 14 to 30 v, vgh to vss = +7.0 to +20 v, vgoffl = (vgl+0.5)v to ? 7.5v, vgoffh = ~ to -1.5v - for the tft-lcd counter electrode: vcom amplitude(max) = 6v, vcomh to vss(max) = gvdd vcoml to vss (max) = 1.0 v to -vci + 0. 5 v
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 5 block diagram 396 ch. source driver built-in gram 132x18x176 = 418,176 bit osc system interface 18/16/9/8-bit parallel, 3-pin spi 178 ch. gate driver vdd3 vss timing generator write data latch control register m/ac circuit latch circuit grayscale voltage generator gamma adjusting circuit built-in power supply circuit address counter read data latch bit operation index register gate control / 72 / 72 / 18 / 18 / 18 /72 vci cl1 m flm eq disptmg osc1 osc2 power regulator gvdd avdd vci1/2/3/4 vbs vgs cvss avss vcl vreg1 vreg1out vreg2 vreg2out regp/regn vcomh/l/r vcomout vgoffh/l vgoffout pregb rdvdd vdd3 vdd / 2 / 3 / 2 vgh vgl vgoff db0/sdi db1/sdo db[17:2] r/w e rs csb im[3:0] resetb /16 / 4 / 4 g177 g176 g175 .. .. .. .. .. .. .. g2 g1 g0 s396 s395 s394 s3 s2 s1 external display interface vsync hsync dotclk enable pd17-0 / 18 pdsb / 18 / 18 figure 1 . S6D0114 block diagram
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 6 pad configuration g109 s1 g107 g0 g1 g99 g121 g161 dummy c31+ c31- vgl g97 dummy dummy 2530 um 20640 um cvss vcl vss im0/id vdd3o im1 vsso im2 vdd3o pregb vdd3o resetb2 im3 vsso db15 db14 db13 db12 db11 db17 db16 dotclk vsso vsync hsync vdd3o enable pd17 pd16 pd15 vsso vdd3o pdsb c31+ c31- vgl vgl vgl vcl cvss cvss vss db10 db9 db8 vsso db7 db6 db5 db4 db3 db2 db1/sdo db0/sdi vsso rd wr/scl rs cs vld vsso pd14 pd13 pd12 pd11 pd10 pd9 pd8 pd7 pd6 pd5 pd4 pd3 pd2 pd1 pd0 g3 g5 g7 g9 g101 dummy dummy g105 g103 g163 g165 g167 g169 g171 g173 g175 dummy dummy dummy dummy dummy dummy dummy s2 s3 s4 s5 s6 s7 s8 ndt_out dummy dummy g119 g117 g115 g113 g111 (with no s/l) (with no s/l) dummy vcomout resetb1 vgh vgh vci3 c23+ c23- c23- c22+ c22- c21+ c21- c41+ c41+ c41- vcomout dummy dummy dummy dummy vci3 c23+ c22+ c22- c21+ c21- c41- figure 2 . pad configuration
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 7 dummy dummy dummy avss vsso S6D0114 x y (0,0) vsso vcomout resetb3 dummy avss avss avss vdd3o vsso o_vss vdd3o rvdd rvdd o_vdd m_vdd vdd vdd vci vci4 osc1 vdd vdd vbs vci vci vci vci osc2 vdd3 vdd3 vdd3 cl1 m flm eq disptmg vgs vgs vss vss vcoml vss vss m_vdd m_vdd vsso cvss cvss m_vss m_vss m_vss vcomh vci1 vci1 vci1 vcomr vreg1out vreg1 gvdd gvdd vci1 regp regn vci2 avdd avdd vci3 c11- c11- c11- c11- c11+ c11+ c11+ c11+ c12- c12- c12- c12- c12+ c12+ c12+ c12+ vgoff vcoml vci3 gvdd avdd avdd vgoffout vgoffh vgoffl vreg2out vreg2 vgoff vgoffout vgoffh vgoffl vreg2 vreg2out dummy dummy dummy dummy vcomout g2 g4 g6 g8 g10 g104 g106 g102 g100 g98 s396 g164 g108 dummy dummy dummy g110 g112 g114 g116 g118 g120 g122 g124 g166 g168 g170 g172 g174 g176 g177 dummy dummy dummy dummy dummy dummy dummy dummy s395 s394 s393 s392 s391 s390 s389 figure 3 . pad configuration (continued)
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 8 table 1 . s6 d0114 pad dimensions size items pad name . x y unit chip size 1) - 20640 2530 input pad 54 100 pad size output pad 36 70 u m notes: scribe line is not included in this chip size (scribe line: 120um)
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 9 align k ey configuration and c oordinate t.b.d figure 4 . cog and ilb align key
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 10 t.b.d figure 5 . bump align key and align key configuration
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 11 pad center coordinates table 2 . p ad center coordinates [unit: um ] (t.b.d)
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 12 pin description power supply pin table 3 . power supply pin description symbol i/o description vdd i / power system power supply. as S6D0114 has internal regulator, vdd range varies with each mode. non-regulated mode (pregb = 1) : +1.8 ~ + 2 . 5 v regulated mode (pregb = 0) : +1.9v vdd3 i / power system power supply for regulator as external power. ( v dd3 : + 2 . 5 ~ + 3.3 v ) avdd o / power a power output pin for source driver block that is generated from power block. connect a capacitor for stabilization. (avdd: +3.5 ~ +5.5 v) interconnect this pin to vci2 pin. gvdd i / power a s tandard level for grayscale voltage generator . connect a capacitor for stabilization. when internal gvdd generator is not used, connect an external power supply, avdd ? 0.5 v vci i / power an internal reference power supply for v reg 1out/v reg 2out . connect vdd when vdd = 2.5 to 3.3 v. connect a 2.5 to 3.3 v external-voltage power supply when v dd = 1.8 to 2.5 v. vss i / power system ground (0v) cvss i / power system ground level for step up circuit block. avss i / power system ground level for analog circuit block. vgs i / power reference voltage for gamma voltage generator. vci1 power a reference voltage in step-up circuit 1. connect a capacitor for stabilization. vci2 power a reference voltage in step-up circuit 2. vci3 power a reference voltage in step-up circuit 3. vci4 power a reference voltage in step-up circuit 4. connect v ci , v dd , or external power supply lower than 3.3 v. vcl power a power supply pin for generating vcoml. when vcoml is higher than vss, outputs vss level.
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 13 table 4 . power supply pin description ( continued) symbol i/o description vbs i reference voltage for step-up circuit3. regn, regp i/o input pins for reference voltages of vreg1out, and vreg2out when the internal reference-voltage generation circuit is not used. leave these pins open when the internal reference-voltage generation circuit is used. vreg1out o this pin outputs a reference voltage for vreg1 between avdd and vss . when the internal reference voltage is not used, the reference voltage can be generated from the voltage of regp. connect this pin to vreg1 and a capacitor for stabilization. when this pin is not used, leave it open. vreg2 out o this pin outputs a reference voltage for vreg2 between vss and vgl when the internal reference voltage is not used, the reference voltage can be generated from the voltage of regn. connect this pin to vreg2 and a capacitor for stabilizatio 0 n. when this pin is not used, leave it open. vcomout o a power supply for the tft-display counter electrode. the alternating cycle can be set by the m pin. connect this pin to the tft-display counter electrode. this pin is also used as equalizing function: when eq = ? high ? period, a ll source driver ? s outputs (s1 to s396) are short to vcom level (hi- z ). in case of vcoml < 0v , equalizing function must not be used. (set eq bit (r07h) to be ? 00 ? for preventing the abnormal function.) vcomr i a reference voltage of vcomh. when vcomh is externally adjusted, halt the internal adjuster of vcomh by setting the register and insert a variable resistor between gvdd and vss . when this pin is not externally adjusted, leave it open and adjust vcomh by setting the internal register. vcomh o this pin indicates a high level of vcom generated in driving the vcom alternation. connect this pin to the capacitor for stabilization. vcoml o when the vcom alternation is driven, this pin indicates a low level of vcom. an internal register can be used to adjust the voltage. connect this pin to a capacitor for stabilization. when the v com g bit is low, the vcoml output stops and a capacitor for stabilization is not needed. vgh o/ power a positive power output pin for gate driver, internal step-up circuits, bias circuits, and operational amplifiers. connect a capacitor for stabilization. interconnect this pin to vci3 pin. vgl o/ power a negative power output pin for gate driver , bias circuits, and operational amplifiers. connect a capacitor for stabilization. when internal vgl generator is not used, connect an external-voltage power supply higher than - 1 5 . 0 v.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 14 table 5 . power supply pin description ( continued) symbol i/o description vgoff i power supply pin for off level for gate of tft. connect v goffout and a capacitor for stabilization. when v goffout is not used, connect an external-voltage power supply higher than - tbd v. vgoffout o an power output pin for gate driver. this pin is a negative voltage for the gate off level. alternation can be synchronized by m pin . set the internal register according to the structure of the tft-display retention volume. for the amplitude at the alternation driving, this pin outputs a voltage between vcomh and vcoml with the vgoffl reference voltage.. vgoffh o when the vgoff alternation is driven, this pin indicates a high level of vgoff. connect a capacitor for stabilization. when the cad bit is low, the vgoffh output stops and a capacitor for stabilization is not needed. vgoffl o when the vgoff alternation is driven, this pin indicates a low level of vgoff. connect a capacitor for stabilization. an internal register can be used to adjust the voltage. c11+ , c11- ~ c23+ , c23- - connect the step-up capacitor according to the step-up factor. c31+ , c31- - connect a step-up capacitor for generating the vgl level . c41+ , c41- - connect a step-up capacitor for generating the - v cl level .
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 15 system interface pin table 6 . system interface pin description symbol i/o description selects the mpu interface mode: im3 im2 im1 im0/id mpu interface mode db pin assign vss vss vss vss 68-system 16-bit bus interface db17-10, db8-1 vss vss vss vdd 68-system 8bit bus interface db17-10 vss vss vdd vss 80-system 16bit bus interface db17-10, db8-1 vss vss vdd vdd 80-system 8bit bus interface db17-10 vss vdd vss id serial peripheral interface (spi) db1-0 vss vdd vdd * non-selecting - vdd vss vss vss 68-system 18-bit bus interface db17-0 vdd vss vss vdd 68-system 9bit bus interface db17-9 vdd vss vdd vss 80-system 18bit bus interface db17-0 vdd vss vdd vdd 80-system 9bit bus interface db17-9 vdd vdd * * non-selecting - im 3 -1, im0/id i when a spi mode is selected, the im0 pin is used as id setting bit for a device code. cs b i chip s elect signal input pin. low: S6D0114 is selected and can be accessed high: S6D0114 is not selected and cannot be accessed must be fixed at vss level when not use d . rs i register select pin. low: index/status, high: control im2 im1 pin func. mpu type pin description vss vss e 68-system read/write operation enable pin. vss vdd /wr 80-system write strobe signal input pin. data is fetched at the low level. e ( /wr ,scl) i vdd vss scl serial peripheral interface (spi) the synchronous clock signal input pin im2 im1 pin func. mpu type pin description vss vss r/w 68-system read/write operation selection pin. low: write , high: read vss vdd /rd 80-system r ead strobe signal input pin. r ead out data at the low level. r / w ( /rd ) i when spi mode is selected, fix this pin at vss level. db0/sdi i/o bi-directional data bus. 18-bit interface : db 17-0 16-bit interface : db 17-10, db 8-1 9-bit interface : db 17-9 8-bit interface : db 17-10 f ix db0 to the vdd 3 or vss level if the pin is not in use. for a serial peripheral interface ( spi) , input data is fetched at the rising edge of the scl signal.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 16 table 7 . system interface pin description (continued) db1/sdo i/o bi-directional data bus. 18-bit interface : db 17-0 16-bit interface : db 17-10, db 8-1 9-bit interface : db 17-9 8-bit interface : db 17-10 f ix db 1 to the vdd 3 or vss level if the pin is not in use. for a serial peripheral interface ( spi) , serves as the serial data output pin (sdo). successive bit s are output at the falling edge of the scl signal. db 17 -db 2 i/o bi-directional data bus. 18-bit interface : db 17-0 16-bit interface : db 17-10, db 8-1 9-bit interface : db 17-9 8-bit interface : db 17-10 f ix unused pin to the vdd 3 or v ss level. data input valid signal when gram is written: csb vld gram write gram address 0 0 valid update 0 1 invalid update 1 * invalid storage vld i f ix vld pin at vss level if the pin is not used. data enable signal pin for rgb interface. high: the ic can be access via rgb interface. low: the ic cannot be access via rgb interface enable vld gram write gram address 1 0 valid update 1 1 invalid update 0 * invalid storage enable i fix enable pin at vdd3 level if the pin is not used. vsync i synchronous signal of frame. low: active fix vsync pin at vdd3 level if the pin is not used. hsync i synchronous signal of line. low: active fix hsync pin at vdd3 level if the pin is not used. dotclk i input pin for dot clock. pd17-pd0 i rgb data input bus. 18-bit interface : pd 17-0 16-bit interface : pd 17-13, pd 11-1 6-bit interface : pd 17-12 f ix unused pin to the vdd 3 or v ss level. pdsb i rgb and system interface hold db17-0 pin in common as a data input pin when pdsb pin is ? low ? . resetb1/ resetb2/ resetb3 i reset pin. initializes the lsi when low. must be reset after power-on.
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 17 display pin table 8 . display pin description symbol i/o description s1 - s396 o source driver output pins. the ss bit can change the shift direction of the source signal. for example, if ss = 0, gray data of s1 is read from ram address 0000 h . if ss = 1, contents of is ram address 0000h is out from s396. s1, s4, s7, ... s(3n-1) : display r ed (r) (ss = 0) s2, s5, s8, ... s(3n-2) : display g reen (g) (ss = 0) s3, s6, s9, ... s(3n) : display b lue (b) (ss = 0) g1 - g176 o gate driver output pins. the output of driving circuit is whether vgh or vgoff. vgh : gate-on level vgoff : gate-off level g0, g177 o gate driver output pins for ic maker ? s testing. please, leave it disconnected. cl1 o output pin for raster-row clock pulse . m o output pin for ac-cycle signa l . flm o output pin for frame-start pulse. eq o output pin for timing for equalizing. low : normal display, high : equalizing disptmg o output pin for gate off signal . high : normal output low : non-display miscellaneous control pin table 9 . oscillator and internal power regulator pin description symbol i/o description osc1/ osc2 i/o connect an external resistor for r-c oscillation. when input the clock from outside, input to osc1, and open osc2. pregb i internal power regulator control input pin. when the internal regulated power (rdvdd) is used as vdd, pregb is fixed to ? low ? level. when the external logic power(vdd3) is used as vdd, pregb is fixed to ? high ? level. rdvdd o internal power regulated-vdd output (typ. 1.8v). when pregb is ? low ? , rdvdd is connected to vdd pin. when pregb is ? high ? , leave this pin open.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 18 functional description system interface the S6D0114 has five high-speed system interfaces: an 80-system 18-/ 16-/ 9-/ 8-bit bus, a 68-system 18-/ 16- /9- /8- bit bus, and a serial interface (spi: serial peripheral interface). the im 3 -0 pins select the interface mode. the S6D0114 has three 1 8 -bit registers: an index register (ir), a write data register (wdr), and a read data register (rdr). the ir stores index information for control register and gram. the wdr temporarily stores data to be written into control register and gram . the rdr temporarily stores data read from gram. data written into the gram from mpu is initially written to the wdr and then written to the gram automatically. data is read through the rdr when reading from the gram, and the first read data is invalid and the second and the following data are valid . when a logic operation is performed inside of the S6D0114 by using the display data stored in the gram and the data written from the mpu, the data read through the rdr is used. accordingly, the mpu does not need to read data twice or to fetch the read data into the mpu. this enables high-speed processing. execution time for instruction , ex cept oscillation start , is 0 - clock cycle so that instructions can be written in succession. table 10 . register selection (18-/16- /9-/8- parallel interface) system r/w /wr e /rd rs operations 0 1 0 write index to ir 1 1 0 read internal status 0 1 1 write to control register and gram through wdr 68 1 1 1 read from gram through rdr 0 1 0 write index to ir 1 0 0 read internal status 0 1 1 write to control register and gram through wdr 80 1 0 1 read from gram through rdr table 11 . csb/vld signal (gram update control) csb vld operation 0 0 data is written to gram, gram address is updated 1 0 data is not written to gram, gram address is not updated 0 1 data is not written to gram, gram address is updated 1 1 data is not written to gram, gram address is not updated table 12 . register selection (serial peripheral interface) r/w bit rs bit operation 0 0 write index to ir 1 0 read internal status 0 1 write data to control register and gram through wdr 1 1 read data from gram through rdr
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 19 external interface (rgb-i/f, vsync-i/f) the S6D0114 incorporates rgb and vsync interface as external interface for motion picture display. when the rgb interface is selected , the synchronization signals ( vsync, hsync, and dotclk) are available for display. the rgb data for display (pd17-0) are written according to enable signal (enable) and data valid signal (vld) in synchronization with vsync, hsync, and dotclk signal. this allows flicker-free updating of the screen. when the vsync interface is selected, internal operation is normally synchronized with internal clock except operation related to frame synchronization : it is synchronized with the vsync signal. the data for display are written to gram via conventional system interface. there are some limitations on the timing and methods for writing to gram in vsync interface. see the section on the external display interface. bit operation the S6D0114 supports the following functions: a write data mask function that selects and writes data to gram in bit unit, a logic operation function that performs logic operations or conditional determination on the display data set in gram and writes to gram. t hese functions can greatly reduce the processing loads of the mpu graphics software and can rewrite the display data in the gram at high speed. for details, see the graphics operation function section. address counter (ac) the address counter (ac) assign address to gram. when an address - set - instruction is written to the ir, the address information is sent from ir to ac. after writing to the gram, the address value of ac is automatically increased /decreased by 1 according to id1-0 bit of control register. after reading data from gram , the ac is not updated. a window address function allows data to be written only to a window area specified by gram. graphics ram (gram) the graphics ram (gram) has 18- bits/pixel and stores the bit-pattern data for 132 -rgb x 176 -dot display. grayscale voltage generator the grayscale voltage circuit generates a certain voltage level that is specified by the grayscale ? -adjusting resistor for lcd driver circuit. by use of the generator, 262,144 colors can be displayed at the same time. for details, see the ? -adjusting resistor section . timing generator the timing generator generates timing signals for the operation of internal circuits such as gram. the g ram read timing for display and the internal operation timing for mpu access is generated separately to avoid interference with one another. several important timing signals can be monitored via signal monitoring pin (m, flm, cl1, eq, disptmg) . oscillation circuit (osc) the S6D0114 can provide r-c oscillation simply through the addition of an external oscillation-resistor between the osc1 and osc2 pin. the appropriate oscillation frequency for operating voltage, display size, and frame frequency
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 20 can be obtained by adjusting the external-resistor value. clock pulse can also be supplied externally. since r-c oscillation stops during the standby mode, current consumption can be reduced. for details, see the oscillation circuit section. source driver circuit th e liquid crystal display source driver circuit consists of 396 drivers (s1 to s396). display pattern data is latched when 396-bit data has arrived. the latched data then enables the source drivers to generate drive waveform outputs. the ss bit can change the shift direction of 396-bit data by selecting an appropriate direction for the device-mounted configuration. gate driver circuit th e liquid crystal display gate driver circuit consists of 178 gate drivers ( g0 to g177 ). the vgh or vgoff level is output by the signal from the gate control circuit. g0 and g177 are ic maker ? s test pins.
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 21 system/rgb interface and gram address setting gram address setting (ss= ? 0 ? ) when ss bit is 0 (source output shift direction: right) and bgr bit is 0 (rgb sequence: right) that can be set in r01h register, gram address is set as follows: table 13 . gram address (ss= ? 0 ? ) s1 s2 s3 s4 s5 s6 s7 s8 s9 s10 s11 s12 ??? s385 s386 s387 s388 s389 s390 s391 s392 s393 s394 s395 s396 db db db db db db db db db db db db db db db db 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 g1 g176 ??? g2 g175 ??? g3 g174 ??? g4 g173 ??? g5 g172 ??? g6 g171 ??? g7 g170 ??? g8 g169 ??? g9 g168 ??? g10 g167 ??? g11 g166 ??? g12 g165 ??? g13 g164 ??? g14 g163 ??? g15 g162 ??? g16 g161 ??? g17 g160 ??? g18 g159 ??? g19 g158 ??? g20 g157 ??? g169 g168 ??? g170 g167 ??? g171 g166 ??? g172 g165 ??? g173 g164 ??? g174 g163 ??? g175 g162 ??? g176 g161 ??? s/g output gs=0 gs=1 ?? ?? "0000"h "0001"h "0002"h "0003"h "0100"h "0101"h "0102"h "0103"h "0200"h "0201"h "0202"h "0203"h "0300"h "0301"h "0302"h "0303"h "0400"h "0401"h "0402"h "0403"h "0500"h "0501"h "0502"h "0503"h "0600"h "0601"h "0602"h "0603"h "0700"h "0701"h "0702"h "0703"h "0800"h "0801"h "0802"h "0803"h "0900"h "0901"h "0902"h "0903"h "0a00"h "0a01"h "0a02"h "0a03"h "0b00"h "0b01"h "0b02"h "0b03"h "0c00"h "0c01"h "0c02"h "0c03"h "0d00"h "0d01"h "0d02"h "0d03"h "0e00"h "0e01"h "0e02"h "0e03"h "0f00"h "0f01"h "0f02"h "0f03"h "1000"h "1001"h "1002"h "1003"h "1100"h "1101"h "1102"h "1103"h "1200"h "1201"h "1202"h "1203"h ?? ?? ?? "1300"h ?? ?? ?? "1301"h "1302"h "1303"h ?? ?? "a800"h "a801"h "a802"h "a803"h "a900"h "a901"h "a902"h "a903"h "aa00"h "aa01"h "aa02"h "aa03"h "ab00"h "ab01"h "ab02"h "ab03"h "ac00"h "ac01"h "ac02"h "ac03"h "ad00"h "ad01"h "ad02"h "ad03"h "ae00"h "ae01"h "ae02"h "ae03"h "af00"h "af01"h "af02"h "af03"h ?? ?? ?? ?? "0080"h "0081"h "0082"h "0083"h "0180"h "0181"h "0182"h "0183"h "0280"h "0281"h "0282"h "0283"h "0380"h "0381"h "0382"h "0383"h "0480"h "0481"h "0482"h "0483"h "0580"h "0581"h "0582"h "0583"h "0680"h "0681"h "0682"h "0683"h "0780"h "0781"h "0782"h "0783"h "0880"h "0881h "0882"h "0883"h "0980"h "0981"h "0982"h "0983"h "0a80"h "0a81"h "0a82"h "0a83"h "0b80"h "0b81"h "0b82"h "0b83"h "0c80"h "0c81"h "0c82"h "0c83"h "0d80"h "0d81"h "0d82"h "0d83"h "0e80"h "0e81"h "0e82"h "0e83"h "0f80"h "0f81"h "0f82"h "0f83"h "1080"h "1081"h "1082"h "1083"h "1180"h "1181"h "1182"h "1183"h "1280"h "1281"h "1282"h "1283"h "1380"h "1381"h "1382"h "1383"h ?? ?? ?? ?? "a880"h "a881"h "a880"h "a883"h "a980"h "a981"h "a980"h "a983"h "aa80"h "aa81"h "aa80"h "aa83"h "ab80"h "ab81"h "ab80"h "ab83"h "ac80"h "ac81"h "ac80"h "ac83"h "ad80"h "ad81"h "ad80"h "ad83"h "ae80"h "ae81"h "ae80"h "ae83"h "af80"h "af81"h "af80"h "af83"h
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 22 data fetch from gram for display when ss=0 is shown in the following figure. system interface 80-system 18-bit interface db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 db 0 gram data r5 r4 r3 r2 r1 r0 s (3n + 1) g5 g4 g3 g2 g1 g0 s (3n + 2) b5 b4 b3 b2 b1 b0 s (3n + 3) rgb arrangement output note: n= lower 8 byte of address (0 to 175) 80-system 16-bit interface db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 gram data r5 r4 r3 r2 r1 r0 s (3n + 1) g5 g4 g3 g2 g1 g0 s (3n + 2) b5 b4 b3 b2 b1 b0 s (3n + 3) rgb arrangement output note: n= lower 8 byte of address (0 to 175) 80-system 9-bit interface db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 gram data r5 r4 r3 r2 r1 r0 s (3n + 1) g5 g4 g3 g2 g1 g0 s (3n + 2) b5 b4 b3 b2 b1 b0 s (3n + 3) rgb arrangement output note: n= lower 8 byte of address (0 to 175) 1st transmission db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 2nd transmission
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 23 80-system 8-bit interface/spi db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 gram data r5 r4 r3 r2 r1 r0 s (3n + 1) g5 g4 g3 g2 g1 g0 s (3n + 2) b5 b4 b3 b2 b1 b0 s (3n + 3) rgb arrangement output note: n= lower 8 byte of address (0 to 175) 1st transmission 2nd transmission rgb interface 18-bit rgb interface pd 17 pd 16 pd 15 pd 14 pd 13 pd 12 pd 11 pd 10 pd 9 pd 8 pd 7 pd 6 pd 5 pd 4 pd 3 pd 2 pd 1 pd 0 gram data r5 r4 r3 r2 r1 r0 s (3n + 1) g5 g4 g3 g2 g1 g0 s (3n + 2) b5 b4 b3 b2 b1 b0 s (3n + 3) rgb arrangement output note: n= lower 8 byte of address (0 to 175) 16-bit rgb interface pd 17 pd 16 pd 15 pd 14 pd 13 pd 9 pd 11 pd 10 pd 8 pd 7 pd 6 pd 5 pd 4 pd 3 pd 2 pd 1 gram data r5 r4 r3 r2 r1 r0 s (3n + 1) g5 g4 g3 g2 g1 g0 s (3n + 2) b5 b4 b3 b2 b1 b0 s (3n + 3) rgb arrangement output note: n= lower 8 byte of address (0 to 175) 6-bit rgb interface db 17 db 16 db 15 db 14 db 13 db 12 gram data r5 r4 r3 r2 r1 r0 s (3n + 1) g5 g4 g3 g2 g1 g0 s (3n + 2) b5 b4 b3 b2 b1 b0 s (3n + 3) rgb arrangement output note: n= lower 8 byte of address (0 to 175) 1st transmission 2nd transmission 3rd transmission db 17 db 16 db 15 db 14 db 13 db 12 db 17 db 16 db 15 db 14 db 13 db 12
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 24 gram address setting (ss= ? 1 ? ) when ss bit is 1 (source output shift direction: reversed) and bgr bit is 1 (rgb sequence: reversed) that can be set in r01h register, gram address is set as follows: table 14 . gram address (ss= ? 1 ? ) s1 s2 s3 s4 s5 s6 s7 s8 s9 s10 s11 s12 ??? s385 s386 s387 s388 s389 s390 s391 s392 s393 s394 s395 s396 db db db db db db db db db db db db db db db db 18 0 18 0 18 0 18 0 18 0 18 0 18 0 18 0 g1 g176 ??? g2 g175 ??? g3 g174 ??? g4 g173 ??? g5 g172 ??? g6 g171 ??? g7 g170 ??? g8 g169 ??? g9 g168 ??? g10 g167 ??? g11 g166 ??? g12 g165 ??? g13 g164 ??? g14 g163 ??? g15 g162 ??? g16 g161 ??? g17 g160 ??? g18 g159 ??? g19 g158 ??? g20 g157 ??? g169 g168 ??? g170 g167 ??? g171 g166 ??? g172 g165 ??? g173 g164 ??? g174 g163 ??? g175 g162 ??? g176 g161 ??? s/g output gs=0 gs=1 ?? ?? ?? ?? ?? ?? ?? ?? "0083"h "0082"h "0081"h "0080"h "0003"h "0002"h "0001"h "0000"h "0183"h "0182"h "0181"h "0180"h "0103"h "0102"h "0101"h "0100"h "0283"h "0282"h "0281"h "0280"h "0203"h "0202"h "0201"h "0200"h "0383"h "0382"h "0381"h "0380"h "0303"h "0302"h "0301"h "0300"h "0483"h "0482"h "0481"h "0480"h "0403"h "0402"h "0401"h "0400"h "0583"h "0582"h "0581"h "0580"h "0503"h "0502"h "0501"h "0500"h "0683"h "0682"h "0681"h "0680"h "0603"h "0602"h "0601"h "0600"h "0783"h "0782"h "0781"h "0780"h "0703"h "0702"h "0701"h "0700"h "0883"h "0882"h "0881h "0880"h "0803"h "0802"h "0801"h "0800"h "0983"h "0982"h "0981"h "0980"h "0903"h "0902"h "0901"h "0900"h "0a83"h "0a82"h "0a81"h "0a80"h "0a03"h "0a02"h "0a01"h "0a00"h "0b83"h "0b82"h "0b81"h "0b80"h "0b03"h "0b02"h "0b01"h "0b00"h "0c83"h "0c82"h "0c81"h "0c80"h "0c03"h "0c02"h "0c01"h "0c00"h "0d83"h "0d82"h "0d81"h "0d80"h "0d03"h "0d02"h "0d01"h "0d00"h "0e83"h "0e82"h "0e81"h "0e80"h "0e03"h "0e02"h "0e01"h "0e00"h "0f83"h "0f82"h "0f81"h "0f80"h "0f03"h "0f02"h "0f01"h "0f00"h "1083"h "1082"h "1081"h "1080"h "1003"h "1002"h "1001"h "1000"h "1183"h "1182"h "1181"h "1180"h "1103"h "1102"h "1101"h "1100"h "1283"h "1282"h "1281"h "1280"h "1203"h "1202"h "1201"h "1200"h "1302"h "1301"h "1300"h "1383"h "1382"h "1381"h "1380"h ?? ?? ?? "1303"h ?? ?? ?? ?? ?? ?? "a880"h "a881"h "a880"h "a803"h "a802"h "a801"h ?? "a800"h "a983"h "a980"h "a981"h "a980"h "a903"h "a902"h "a901"h "a900"h "a883"h "aa83"h "aa80"h "aa81"h "aa80"h "aa03"h "aa02"h "aa01"h "aa00"h "ab83"h "ab80"h "ab81"h "ab80"h "ab03"h "ab02"h "ab01"h "ab00"h "ac83"h "ac80"h "ac81"h "ac80"h "ac03"h "ac02"h "ac01"h "ac00"h "ad83"h "ad80"h "ad81"h "ad80"h "ad03"h "ad02"h "ad01"h "ad00"h "ae83"h "ae80"h "ae81"h "ae80"h "ae03"h "ae02"h "ae01"h "ae00"h "af83"h "af80"h "af81"h "af80"h "af03"h "af02"h "af01"h "af00"h
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 25 data fetch from gram for display when ss=1 is shown in the following figure. system interface 80-system 18-bit interface db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 db 0 gram data r5 r4 r3 r2 r1 r0 s (396-3n) g5 g4 g3 g2 g1 g0 s (395-3n) b5 b4 b3 b2 b1 b0 s (394-3n) rgb arrangement output note: n= lower 8 byte of address (0 to 175) 80-system 16-bit interface db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 gram data r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 rgb arrangement output note: n= lower 8 byte of address (0 to 175) s (396-3n) s (395-3n) s (394-3n) 80-system 9-bit interface db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 gram data r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 rgb arrangement output note: n= lower 8 byte of address (0 to 175) 1st transmission db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 2nd transmission s (396-3n) s (395-3n) s (394-3n)
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 26 80-system 8-bit interface db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 gram data r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 rgb arrangement output note: n= lower 8 byte of address (0 to 175) 1st transmission 2nd transmission s (396-3n) s (395-3n) s (394-3n) rgb interface 18-bit interface pd 17 pd 16 pd 15 pd 14 pd 13 pd 12 pd 11 pd 10 pd 9 pd 8 pd 7 pd 6 pd 5 pd 4 pd 3 pd 2 pd 1 pd 0 gram data r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 rgb arrangement output note: n= lower 8 byte of address (0 to 175) s (396-3n) s (395-3n) s (394-3n) 16-bit interface pd 17 pd 16 pd 15 pd 14 pd 13 pd 9 pd 11 pd 10 pd 8 pd 7 pd 6 pd 5 pd 4 pd 3 pd 2 pd 1 gram data r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 rgb arrangement output note: n= lower 8 byte of address (0 to 175) s (396-3n) s (395-3n) s (394-3n) 6-bit interface db 17 db 16 db 15 db 14 db 13 db 12 gram data r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 rgb arrangement output note: n= lower 8 byte of address (0 to 175) 1st transmission 2nd transmission 3rd transmission db 17 db 16 db 15 db 14 db 13 db 12 db 17 db 16 db 15 db 14 db 13 db 12 s (396-3n) s (395-3n) s (394-3n)
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 27 instructions the S6D0114 uses the 1 8 -bit bus architecture. before the internal operation of the S6D0114 starts, control information is temporarily stored in the registers described below to allow high-speed interfacing with a high- performance microcomputer. the internal operation of the S6D0114 is determined by signals sent from the microcomputer. these signals, which include the register selection signal (rs), the read/write signal (r/w), and the data bus signals (db1 7 to db0), make up the S6D0114 instructions. there are nine categories of instructions that: - specify the index - read the status - control the display - control power management - process the graphics data - set internal gram addresses - transfer data to and from the internal gram - set grayscale level for the internal grayscale palette table - interface with the gate driver and power supply ic normally, instructions that write data are used the most. however, an auto-update of internal gram addresses after each data write can lighten the microcomputer program load. as instructions are executed in 0 cycles, they can be written in succession. the 16-bit instruction assignment differ from interface-setup (18-/16-/9-/8-/spi), so instructions should be fetched according to the data format shown below: 80-system 18-bit interface db 17 input data instruction bit (ib) db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 db 0 ib 15 ib 14 ib 13 ib 12 ib 11 ib 10 ib 9 ib 8 ib 7 ib 6 ib 5 ib 4 ib 3 ib 2 ib 1 ib 0 80-system 16-bit interface db 17 input data instruction bit (ib) db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 ib 15 ib 14 ib 13 ib 12 ib 11 ib 10 ib 9 ib 8 ib 7 ib 6 ib 5 ib 4 ib 3 ib 2 ib 1 ib 0
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 28 80-system 9-bit interface 1st transmission 2nd transmission db 17 input data instruction bit (ib) db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 db 0 ib 15 ib 14 ib 13 ib 12 ib 11 ib 10 ib 9 ib 8 ib 7 ib 6 ib 5 ib 4 ib 3 ib 2 ib 1 ib 0 80-system 8-bit interface/spi (2-transfer per pixel) db 17 input data instruction bit (ib) db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 ib 15 ib 14 ib 13 ib 12 ib 11 ib 10 ib 9 ib 8 ib 7 ib 6 ib 5 ib 4 ib 3 ib 2 ib 1 ib 0 1st transmission 2nd transmission
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 29 instruction table table 15 . instruction table 1 reg. no r/w rs db 15 db 1 4 db 1 3 db 1 2 db 1 1 db 1 0 db 9 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 db 0 register n ame / description ir 0 0 * * * * * * * * * id6 id5 id4 id3 id2 id1 id0 index / sets the index register value sr 1 0 l7 l6 l5 l4 l3 l2 l1 l0 0 0 0 0 0 0 0 0 status read / reads the internal status of the S6D0114 0 1 * * * * * * * * * * * * * * * 1 start oscillation(r00h) / starts the oscillation circuit r00h 1 1 0 0 0 0 0 0 0 1 0 0 0 1 0 1 0 0 device code read / read 0114h r01h 0 1 0 0 0 0 epl sm gs ss 0 0 0 nl4 nl3 nl2 nl1 nl0 driver output control(r01h) / epl: set polarity of enable pin while using rgb interface. sm: gate driver division drive control gs: gate driver shift direction ss: source driver shift direction nl4-0: number of driving lines r02h 0 1 0 0 0 0 fld1 fdl0 b/c eor 0 0 nw5 nw4 nw3 nw2 nw1 nw0 lcd-driving-waveform control (r02h)/ fld1-0: number of interlaced field b/c: lcd drive ac waveform eor: exclusive or-ing the ac waveform nw5-0: number of n-raster-row of c- pattern r03h 0 1 0 0 0 bgr 0 0 hwm 0 0 0 i/d1 i/d0 am lg2 lg1 lg0 entry mode(r03h) / bgr: rgb swap control hwm: high-speed ram write i/d1-0: address counter increment / decrement control am: horizontal / vertical ram update lg2-0: logic operation control r04h 0 1 0 0 cp11 cp10 cp9 cp8 cp7 cp6 0 0 cp5 cp4 cp3 cp2 cp1 cp0 compare register 1(r04h)/ r05h 0 1 0 0 0 0 0 0 0 0 0 0 cp17 cp16 cp15 cp14 cp13 cp12 compare register 2(r05h)/ r07h 0 1 0 0 0 pt1 pt0 vle2 vle1 spt 0 0 gon dte cl rev d1 d0 display control (r07h) / pt1-0: non-display area source output control vle2-1: 1 st /2 nd partial vertical scroll spt: 1 st /2 nd partial display enable gon: gate-off to be vss level dte:disptmg to be vss level cl: 8-color display mode enable rev: display area inversion drive d1-0: source output control r08h 0 1 0 0 0 0 fp3 fp2 fp1 fp0 0 0 0 0 bp3 bp2 bp1 bp0 blank period control 1 (r08h)/ bp3-0: back porch setting fp3-0: front porch setting r09h 0 1 0 0 0 0 blp1 3 blp1 2 blp1 1 blp1 0 blp2 3 blp2 2 blp2 1 blp2 0 0 0 0 0 blank period control 2 (r09h)/ blp1: blanking period setting blp2: blanking period setting r0bh 0 1 no1 no0 sdt1 sdt0 eq1 eq0 div1 div0 0 0 0 0 rtn3 rtn2 rtn1 rtn0 frame cycle control (r0bh)/ no1-0: specify the amount of non-overlap sdt1-0: set amount of source delay eq1-0: equalizing period setting dvi1-0: division ratio of internal clock setting rtn3-0: set the 1-h period r0ch 0 1 0 0 0 0 0 0 0 rm 0 0 dm1 dm2 0 0 rim0 rim1 external interface control(r0ch) / rm: specify the interface for ram access dm2-1: specify display operation mode rim1-0 : specify rgb-i/f mode r10h 0 1 0 0 sap2 sap1 sap0 bt2 bt1 bt0 dc2 dc1 dc0 ap2 ap1 ap0 slp stb power control 1 (r10h) / sap2-0: bt2-0: dc2-0: ap2-0: slp : stb: r11h 0 1 cad 0 0 vrn4 vrn3 vrn2 vrn1 vrn0 0 0 0 vrp4 vrp3 vrp2 vrp1 vrp0 power control 2 (r11h)/ cad : vrn4-0: vrp4-0:
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 30 table 16 . instruction table 2 reg. no r/w rs db 15 db 1 4 db 1 3 db 1 2 db 1 1 db 1 0 db 9 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 db 0 register n ame / description r12h 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 vc2 vc1 vc0 power control 3 (r12h)/ vc2-0: r13h 0 1 0 0 0 0 vrl3 vrl2 vrl1 vrl0 0 0 0 pon vrh3 vrh2 vrh1 vrh0 power control 4 (r13h)/ pon: vrl3-0: vrh3-0: r14h 0 1 0 0 vco mg vdv4 vdv3 vdv2 vdv1 vdv0 0 0 0 vcm4 vcm3 vcm2 vcm1 vcm0 power control 5 (r14h)/ vcomg : vdv4-0: vcm4-0: r16h 0 1 hea7 hea6 hea5 hea4 hea3 hea2 hea1 hea0 hsa7 hsa6 hsa5 hsa4 hsa3 hsa2 hsa1 hsa0 horizontal ram address position (r16h)/ hea7-0: hsa7-0 r17h 0 1 vea7 vea6 vea5 vea4 vea3 vea2 vea1 vea0 vsa7 vsa6 vsa5 vsa4 vsa3 vsa2 vsa1 vsa0 vertical ram address position (r17h)/ hea7-0: hsa7-0 r21h 0 1 ad15 ad14 ad13 ad12 ad11 ad10 ad9 ad8 ad7 ad6 ad5 ad4 ad3 ad2 ad1 ad0 ram address set (r21h)/ ad15-0: 0 1 wd15 wd14 wd13 wd12 wd11 wd10 wd9 wd8 wd7 wd6 wd5 wd4 wd3 wd2 wd1 wd0 write data to gram (r22h)/ wd15-0: r22h 1 1 rd15 rd14 rd13 rd12 rd11 rd10 rd9 rd8 rd7 rd6 rd5 rd4 rd3 rd2 rd1 rd0 read data from gram (r22h)/ rd15-0: r23h 0 1 0 0 wm11 wm10 wm9 wm8 wm7 wm6 0 0 wm5 wm4 wm3 wm2 wm1 wm0 ram write data mask 1 (r23h)/ wm11-0: r24h 0 1 0 0 0 0 0 0 0 0 0 0 wm17 wm16 wm15 wm14 wm13 wm12 ram write data mask 2 (r24h)/ wm17-12: r30h 0 1 0 0 0 0 0 pkp 12 pkp 11 pkp 10 0 0 0 0 0 pkp 02 pkp 01 pkp 00 gamma control 1 (r30h)/ adjust gamma voltage r31h 0 1 0 0 0 0 0 pkp 32 pkp 31 pkp 30 0 0 0 0 0 pkp 22 pkp 21 pkp 20 gamma control 2 (r31h)/ adjust gamma voltage r32h 0 1 0 0 0 0 0 pkp 52 pkp 51 pkp 50 0 0 0 0 0 pkp 42 pkp 41 pkp 40 gamma control 3 (r32h)/ adjust gamma voltage r33h 0 1 0 0 0 0 0 prp 12 prp 11 prp 10 0 0 0 0 0 prp 02 prp 01 prp 00 gamma control 4 (r33h)/ adjust gamma voltage r34h 0 1 0 0 0 0 0 pkn 12 pkn 11 pkn 10 0 0 0 0 0 pkn 02 pkn 01 pkn 00 gamma control 5 (r34h)/ adjust gamma voltage r35h 0 1 0 0 0 0 0 pkn 32 pkn 31 pkn 30 0 0 0 0 0 pkn 22 pkn 21 pkn 20 gamma control 6 (r35h)/ adjust gamma voltage r36h 0 1 0 0 0 0 0 pkn 52 pkn 51 pkn 50 0 0 0 0 0 pkn 42 pkn 41 pkn 40 gamma control 7 (r36h)/ adjust gamma voltage r37h 0 1 0 0 0 0 0 prn 12 prn 11 prn 10 0 0 0 0 0 prn 02 prn 01 prn 00 gamma control 8 (r37h)/ adjust gamma voltage r40h 0 1 0 0 0 0 0 0 0 0 0 0 0 scn4 scn3 scn2 scn1 scn0 gate scan position (r40h)/ scn4-0: scan starting position of gate r41h 0 1 0 0 0 0 0 0 0 0 vl7 vl6 vl5 vl4 vl3 vl2 vl1 vl0 vertical scroll control (r41h)/ vl7-0: r42h 0 1 se17 se16 se15 se14 se13 se12 se11 se10 ss17 ss16 ss15 ss14 ss13 ss12 ss11 ss10 1 st screen driving position (r42h)/ se17-10: ss17-10 r43h 0 1 se27 se26 se25 se24 se23 se22 se21 se20 ss27 ss26 ss25 ss24 ss23 ss22 ss21 ss20 2 nd screen driving position (r43h)/ se27-20: ss27-20
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 31 instruction descriptions index the index instruction specifies the ram control indexes (r00h to r3fh). it sets the register number in the range of 00000 to 111111 in binary form. however, r40 to r44 are disabled since they are test registers. r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 0 * * * * * * * * * id6 id5 id4 id3 id2 id1 id0 status read the status read instruction read out the internal status of the ic . r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 r 0 l7 l6 l5 l4 l3 l2 l1 l0 0 0 0 0 0 0 0 0 l7 ? 0: indicate the driving raster-row position where the liquid crystal display is being driven. start oscillation (r00h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 * * * * * * * * * * * * * * * 1 r 1 0 0 0 0 0 0 0 1 0 0 0 1 0 1 0 0 the start oscillation instruction restarts the oscillator from the halt state in the standby mode. after this instruction, wait at least 10 ms for oscillation to stabilize before giving the next instruction. (see the standby mode section) if this register is read forcibly, *0114h is read.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 32 driver output control (r01h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 0 0 0 0 epl sm gs ss 0 0 0 nl4 nl3 nl2 nl1 nl0 gs: selects the output shift direction of the gate driver. when gs = 0, g1 shifts to g 176 . when gs = 1, g176 shifts to g1. sm : select the division drive method of the gate driver. when sm = 0, even/odd division is selected; sm = 1, upper/lower division drive is selected. various connections between tft panel and the ic can be supported with the combination of sm and gs bit. ss: selects the output shift direction of the source driver. when ss = 0, s1 shifts to s396. when ss = 1, s396 shifts to s1. in addition, ss and bgr bits should be specified in case of the rgb order is changed. when ss = 0 and bgr = 0 , are assigned in order from s1 pin . when ss = 1 and bgr = 1 , are assigned in order from s396. re-write data to g ram when ever ss and bgr bit are changed . epl: set the polarity of enable pin while using rgb interface. epl = ? 0 ? : enable = ? low ? / write data of pd17-0 enable = ? high ? / don ? t write data of pd17-0 epl = ? 1 ? : enable = ? high ? / write data of pd17-0 enable = ? low ? / don ? t write data of pd17-0 table 17 . relationship between epl, enable, vld and ram access epl enable vld ram write ram address 0 0 0 valid updated 0 0 1 invalid updated 0 1 * invalid held 1 1 0 valid updated 1 1 1 invalid updated 1 0 * invalid held
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 33 nl4 ? 0: specify the number of raster-rows to be drive n . the n umber of raster-row can be adjusted in units of eight. gram address mapping is independent of this setting . the set value should be higher than the panel size. table 18 . nl bit and drive duty (scn4-0=00000) nl4 nl3 nl2 nl1 nl0 display size number of lcd driver lines gate driver used 0 0 0 0 0 setting disabled setting disabled setting disabled 0 0 0 0 1 396 x 16 dots 16 g1 to g16 0 0 0 1 0 396 x 24 dots 24 g1 to g24 0 0 0 1 1 396 x 32 dots 32 g1 to g32 0 0 1 0 0 396 x 40 dots 40 g1 to g40 0 0 1 0 1 396 x 48 dots 48 g1 to g48 0 0 1 1 0 396 x 56 dots 56 g1 to g56 0 0 1 1 1 396 x 64 dots 64 g1 to g64 0 1 0 0 0 396 x 72 dots 72 g1 to g72 0 1 0 0 1 396 x 80 dots 80 g1 to g80 0 1 0 1 0 396 x 88 dots 88 g1 to g88 0 1 0 1 1 396 x 96 dots 96 g1 to g96 0 1 1 0 0 396 x 104 dots 104 g1 to g104 0 1 1 0 1 396 x 112 dots 112 g1 to g112 0 1 1 1 0 396 x 120 dots 120 g1 to g120 0 1 1 1 1 396 x 128 dots 128 g1 to g128 1 0 0 0 0 396 x 136 dots 136 g1 to g136 1 0 0 0 1 396 x 144 dots 144 g1 to g144 1 0 0 1 0 396 x 152 dots 152 g1 to g152 1 0 0 1 1 396 x 160 dots 160 g1 to g160 1 0 1 0 0 396 x 168 dots 168 g1 to g168 1 0 1 0 1 396 x 176 dots 176 g1 to g176 n ote : a fp ( front porch) and bp ( back porch) period will be inserted as b lank ing period ( a ll gates output vgoff level) before / after the driver scan through all of the scans.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 34 lcd-driving-waveform control (r02h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 0 0 0 0 fld 1 fld 0 b/c eor 0 0 nw5 nw4 nw3 nw2 nw1 nw0 fld1-0: these bits are for the set up of the interlaced driver ? s n raster-row. see the following table and figure for the set up value and field raster-row and scanning method. table 19 . association chart for scanning fld1-0 and n raster-row fld1 fld0 scanning method 0 0 set up disabled 0 1 1 field 1 0 set up disabled 1 1 3 field (interlaced) g1 4 g2 4 g3 4 ..... g174 4 g175 4 g176 tft panel (a) when fld1-0= 01(normal scanning) g1 4 g4 4 g7 4 ..... 4 g174 tft panel g2 4 g5 4 g8 4 ..... 4 g175 g3 4 g6 4 g9 4 ..... 4 g176 tft panel tft panel 1 frame frame 1/3 frame 2/3 frame 3/3 (b) when fld1-0= 11(interlaced scanning) figure 6 . n raster-row interlaced scanning method b/c: when b/c = 0, a b-pattern waveform is generated and alternates at every frame. when b/c = 1, a n n raster- row ac waveform is generated and alternates in each raster-row specified by bits eor and nw4 ? nw0 in the lcd-driving-waveform control register (r02h) . for details, see the n-raster-row reversed ac drive section.
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 35 eor: when the c-pattern waveform is set (b/c = 1) and eor = 1, the odd/even frame-select signals and the n- raster-row reversed signals are eored (exclusive-or) for alternating drive. eor is used when the lcd is not alternated by combining the set values of the number of the lcd drive raster-row and the n raster-row. for details, see the n-raster-row reversed ac drive section. nw5 ? 0: specify the number of raster-rows that will alternate in the c-pattern waveform setting (b/c = 1). nw4 ? nw0 alternate for every set value + 1 raster-row, and the first to the 64th raster-rows can be selected.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 36 entry mode (r03h) compare register 1 (r04h) compare register 2 (r05h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 0 0 0 bgr 0 0 hwm 0 0 0 i/d1 i/d0 am lg2 lg1 lg0 w 1 0 0 cp11 cp10 cp9 cp8 cp7 cp6 0 0 cp5 cp4 cp3 cp2 cp1 cp0 w 1 0 0 0 0 0 0 0 0 0 0 cp17 cp16 cp15 cp14 cp13 cp12 the write date sent from mpu is modified in the S6D0114 and written to the gram. the display data in the gram can be quickly rewritten to reduce the load of the microcomputer software processing. for details, see the graphics operation function section. hwm: when hwm=1, data can be written to the gram at high speed. in high-speed write mode, four words of data are written to the gram in a single operation a f t er writing to g ram four times. write to ram four times, otherwise the four words cannot be written to the gram. thus, set the lower 2 bits to 0 when setting the ram address. for details, see the high speed ram write mode section. i/d1-0: when i/d1-0 = 1, the address counter (ac) is automatically increas ed by 1 after the data is written to the gram. when i/d1-0 = 0, the ac is automatically decreased by 1 after the data is written to the gram. automatic address counter updating is not performed when reading data from gram . the increment/decrement setting of the address counter by i/d1-0 bits is performed independently for the upper (ad15-8) and lower (ad7-0) addresses. the am bit sets the direction of moving through the addresses when the gram is written. am: set the automatic update method of the ac after the data is written to the gram. when am = 0, the data is continuously written in parallel. when am = 1, the data is continuously written vertically. w h en window address range is specified, the gram in the window address range can be written to according to the i/d1-0 and am settings. table 20 . address direction setting i/d1-0= ? 00 ? h: decrement v: decrement i/d1-0= ? 01 ? h: increment v: increment i/d1-0= ? 10 ? h: decrement v: increment i/d1-0= ? 11 ? h: increment v: increment am=0 horizontal 0000 h af83h 0000 h af83h 0000 h af83h 0000 h af83h am=1 vertical 0000 h af83h af83h 0000 h af83h 0000 h af83h 0000 h
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 37 lg2 ? 0: compare the data read from the gram by the microcomputer with the compare registers (cp 1 7 ? 0) by a compare/logical operation and write the results to gram. for details, see the logical/compare operation function. cp1 7 ? 0: set the compare register for the compare operation with the data read from the gram or written by the microcomputer. note: this function is not available when the external display interface (i.e. rgb interface or vsync interface) is in use. therefore, lg2-0 bits should be set to be ? 000 ? , respectively. db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 db 0 write data to gram *1 write data to gram logical/ compare operation 18 bits conversion of rgb to bgr (vice versa) logic operation(write data) compare operation (with compare register) lg2-0 = 000 : replacement lg2-0 = 110 : replacement of matched write data write data mask (wm17-0) gram figure 7 . rgb swapping and logical/compare operation note: 1) data is written to gram in 18-bit units. logical and compare operations are also performed in 18-bit units. 2) the write data mask(wm17-0) is set by the register in the ram write data mask section
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 38 display control (r07h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 0 0 0 pt1 pt0 vle2 vle1 spt 0 0 gon dte cl rev d1 d0 pt1-0: normalize the source outputs when non-displayed area of the partial display is driven. for details, see the screen-division driving function section. source output for non-display area gate output for non-display area pt1 pt0 positive polarity negative polarity gate driver used 0 0 v63 v0 normal drive 0 1 v0 v63 vgoff 1 0 gnd gnd vgoff 1 1 hi-z hi-z vgoff vle2 ? 1: when vle1 = 1, a vertical scroll is performed in the 1st screen. when vle2 = 1, a vertical scroll is performed in the 2nd screen. vertical scrolling on the two screens cannot be controlled at the same time. vle2 vle1 2 nd screen 1 st screen 0 0 fixed display fixed display 0 1 fixed display scroll 1 0 scroll fixed display 1 1 setting disabled setting disabled spt: when spt = 1, the 2-division lcd drive is performed. for details, see the screen-division driving function section. note: this function is not available when the external display interface (i.e. rgb interface or vsync interface) is in use. gon: gate off level is set to be vss when gon = 0. when gon= 0 and disptmg= 0, g1 to g176 output is fixed to vss level . when gon= 1, g1 to g176 output is fixed to vgh or vgoff level. see the instruction set up flow for further description on the display on/off flow. dte: disptmg output is fixed to vss when dte = 0. gon gate output dte disptmg output 0 vgh/vss 0 halt (vss) 1 vgh/vgoff 1 operation (vdd/vss) cl: cl = 1 selects 8-color display mode. for details, see the section on 8-color d isplay m ode. cl number of display colors 0 262,144 colors 1 8 colors
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 39 rev: displays all character and graphics display sections with reversal when rev = 1. for details, see the reversed display function section. since the grayscale level can be reversed, display of the same data is enabled on normally white and normally black panels. 1) combination with the pt1-0 bit source output level non-display area display area pt1-0=(0,0) pt1-0=(0,1) pt1-0=(1,0) pt1-0=(1,1) rev gram data positive negative positive negative positive negative positive negative positive negative 0 18 ? h00000 : 18 ? h3ffff v63 : v0 v0 : v63 v63 v0 v63 v0 vss vss hi-z hi-z 1 18 ? h0000 : 18 ? h3ffff v0 : v63 v63 : v0 v63 v0 v63 v0 vss vss hi-z hi-z d1 ? 0: display is on when d1 = 1 and off when d1 = 0. when off, the display data remains in the gram, and can be re- displayed instantly by setting d1 = 1. when d1 is 0, the display is off with the entire source outputs set to the vss level. because of this, the S6D0114 can control the charging current for the lcd with ac driving. control the display on/off while control gon and dte. for details, see the instruction set up flow. when d1 ? 0 = 01, the internal display of the S6D0114 is performed although the display is off. when d1-0 = 00, the internal display operation halts and the display is off. d1 d0 source output S6D0114 internal display operation master/slave signal (cl1, flm, m, disptmg) 0 0 vss halt halt 0 1 vss operate operate 1 0 unlit display operate operate 1 1 display operate operate notes: 1. writing from mcu to gram is independent from d1 ? 0. 2. in sleep and standby mode, d1 ? 0 = 00. however, the register contents of d1 ? 0 are not modified .
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 40 blanking period control 1 (r08h) blanking period control 2 (r09h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 0 0 0 0 fp3 fp2 fp1 fp0 0 0 0 0 bp3 bp2 bp1 bp0 w 1 0 0 0 0 blp1 3 blp1 2 blp1 1 blp1 0 blp2 3 blp2 2 blp2 1 blp2 0 0 0 0 0 the blanking period in the front and end of the display area can be defined using this register. when n -raster-row is driving, a blank period is inserted after all screens are drawn. front and back porch can be adjusted using fp3-0 and bp3-0 bits (r08h). in interlace drive mode, blank period can be adjusted using blp13-0 and blp23-0 bit (r09h). for details, see the graphics operation function section. fp3-0/bp3-0 : set the periods of blanking (the front and back porch), which are placed at the beginning and end of the display. fp3-0 are for a front porch and bp3-0 are for a back porch. when front and back porches are set, the settings should meet the following conditions. bp + fp = 16 raster-rows fp 3 2 raster-rows bp 3 2 raster-rows when the external display interface is in use, the front porch (fp) will start on the falling edge of the vsync signal and display operation commences at the end of the front-porch period. the back porch (bp) will start when data for the number of raster-rows specified by the nl bits has been displayed. during the period between the completion of the back-porch period and the next vsync signal, the display will remain blank. note: in the internal clock mode, the blanking periods described above should be bp=0011 (3 raster-rows) and fp=0101 (5 raster-rows) table 21 . front/back porch fp3 bp3 fp2 bp2 fp1 bp1 fp0 bp0 # of raster periods in the front porch # of raster periods in the back porch 0 0 0 0 setting disabled 0 0 0 1 setting disabled 0 0 1 0 2 0 0 1 1 3 0 1 0 0 4 . . . . . . . . . . . . . . . 1 1 0 0 12 1 1 0 1 13 1 1 1 0 14 1 1 1 1 setting disabled blp13-0/blp23-0 : in interlaced drive (3-field) mode, blanking period inserted every 1/3 frame. blp13-0 and blp23-0 bit can / adjust that blanking period.
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 41 frame cycle control (r0bh) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 no1 no0 sdt1 sdt0 eq1 eq0 div1 div0 0 0 0 0 rtn3 rtn2 rtn1 rtn0 rtn3-0: set the 1h period (1 raster-row). rtn3 rtn2 rtn1 rtn0 clock cycles per raster row 0 0 0 0 16 0 0 0 1 17 0 0 1 0 18 . . . . . . . . . . . . . . . 1 1 1 0 30 1 1 1 1 31 div1-0: set the division ratio of clocks for internal operation (div1-0). internal operations are driven by clocks, which are frequency divided according to the div1-0 setting. frame frequency can be adjusted along with the 1h period (rtn3-0). when changing number of the drive cycle, adjust the frame frequency. for details, see the frame frequency adjustment function section. div1 div0 division ratio internal operation clock frequency 0 0 1 fosc/1 0 1 2 fosc/2 1 0 4 fosc/4 1 1 8 fosc/8 *fosc = r-c oscillation frequency frame frequency = f osc clock cycles per raster-row x division ratio x (line+b) [ hz] f osc : r-c oscillation frequency line: number of raster-rows (nl bit) clock cycles per raster-row: rtn bit division ratio: div bit b: blank period(back porch + front porch) figure 8 . formula for the frame frequency
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 42 eq1-0: eq period is sustained for the number of clock cycle which is set on eq1-0. when vcoml<0, set these bits as ? 00 ? for preventing the abnormal function. eq1 eq0 eq period internal operation (synchronized with internal clock) rgb i/f operation (synchronized with dotclk) 0 0 no eq no eq 0 1 1 clock cycle 8 clock cycle 1 0 2 clock cycle 16 clock cycle 1 1 3 clock cycle 24 clock cycle sd t 1-0: set delay amount from gate edge (end) to source output. sdt1 sdt0 delay amount of the source output 0 0 1 clock cycle 0 1 2 clock cycle 1 0 3 clock cycle 1 1 4 clock cycle cl1 m gn sn eq 1h period 1h period delay time for source output period of equalizing figure 9 . set delay from gate output to source output and eq signal
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 43 no1-0: set amount of non-overlay for the gate output. no1 no0 amount of non-overlap 0 0 0 clock cycle 0 1 4 clock cycle 1 0 6 clock cycle 1 1 8 clock cycle note: the amount of non-overlap time is defined from the falling edge of the cl1 gn gn +1 1 h period 1 h period non - overlap period cl1 gn gn +1 1 h period 1 h period non - overlap period cl1 figure 10 . non-overlap period note: the values specified by the bits of eq, sdt1-0 and no1-0 vary in a reference clock for each interface mode. internal operation mode : internal r-c oscillation clock rgb-i/f mode : dotclk vsync-i/f : internal r-c oscillation clock
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 44 external display control (r0ch) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 0 0 0 0 0 0 0 rm 0 0 dm1 dm2 0 0 rim1 rim0 rim1 -0: specify the rgb interface mode when the rgb interface is used. specifically, this setting specifies the mode when the bits of dm and rm are set to rgb interface. these bits should be set before display operation through the rgb interface and should not be set during operation. rim1 rim0 rgb interface mode 0 0 18-bit rgb interface (one transfer/pixel) 0 1 16-bit rgb interface (one transfer /pixel) 1 0 6-bit rgb interface (three transfers /pixel) 1 1 setting disabled dm1-0: specify the display operation mode. the interface can be set based on the bits of dm1-0. this setting enables switching interface between internal operation and the external display interface. switching between two external display interfaces (rgb interface and vsync interface) should not be done. dm1 dm0 rgb interface mode 0 0 internal clock operation 0 1 rgb interface 1 0 vsync interface 1 1 setting disabled rm: specifies the interface for ram accesses. ram accesses can be performed through the interface specified by the bits of rm1-0. when the display data is written via the rgb interface, 1 should be set. this bit and the dm bits can be set independently. the display data can be written via the system interface by clearing this bit while the rgb interface is used. rm interface for ram access 0 system interface / vsync interface 1 rgb interface
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 45 depending on the external display interface setting, differnet interfaces for use can be specified to match the display state. while displaying moving pictures (rgb interface/vsync interface), the data for display can be written in high-speed write mode, which achieves both low power consumption and high-speed access. table 22 . display state and interface display state operation mode ram access (rm) display operation mode (dm1-0) still pictures internal clock system interface (rm=0) internal clock (dm1-0=00) motion pictures rgb interface (1) rgb interface (rm=1) rgb interface (dm1-0=01) rewrite still picture area while displaying motion pictures rgb interface (2) system interface (rm=0) rgb interface (dm1-0=01) motion picture display vsync interface system interface (rm=0) vsync interface (dm1-0=10) note: 1) the instruction register can only be set through the system interface. 2) switching between rgb interface and vsync interface cannot be done. 3) the rgb interface mode should not be set during operation. 4) for the transition flow for each operation mode, see the external display interface section. 5) rgb interface and vsync interface should be used in high-speed write mode (hwm=1). internal clock mode all display operation is controlled by signals generated by the internal clock in internal clock mode. all inputs through the external display interface are invalid. the internal ram can be accessed only via the system interface. rgb interface mode (1) the display operations are controlled by the frame synchronization clock (vsync), raster-row synchronization signal (vsync), and dot clock (dclk) in rgb interface mode. these signals should be supplied during display operation in this mode. the display data is transferred to the internal ram via pd17-0 for each pixel. combining the function of the high- speed write mode and the window address enables display of both the motion picture area and the internal ram area simultaneously. in this method, data is only transferred when the screen is updated, which reduces the amount of data transferred. the periods of the front (fp ), back (bp) porch, and the display are automatically generated in the S6D0114 by counting the raster-row synchronization signal (hsync) based on the frame synchronization signal (vsync). rgb interface mode (2) when rgb interface is in use, data can be written to ram via the system interface. this write operation should be performed while data for display is not being transferred via rgb interface (enable = low). before the next data transfer for display via rgb interface, the setting above should be changed, and then the address and index (r22h) should be set.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 46 vsync interface mode the internal display operation is synchronized with the frame synchronization signal (vsync) in vsync interface mode. when data is written to the internal ram with the required speed after the falling edge of vsync, motion pictures can be displayed via the conventional interface. there are some limitations on the timing and methods of writing to ram. see the section on the external display interface. in vsync interface mode. only the vsync input is valid. the other input signals for the external display interface are invalid. the periods of the front and back porch and display period are automatically generated by the frame synchronization signal (vsync) according to the setting of the S6D0114 registers.
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 47 power control 1 (r10h) power control 2 (r11h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 0 0 sap 2 sap 1 sap 0 bt2 bt1 bt0 dc2 dc1 dc0 ap2 ap1 ap0 slp stb w 1 cad 0 0 vrn 4 vrn 3 vrn 2 vrn 1 vrn 0 0 0 0 vrp 4 vrp 3 vrp 2 vrp 1 vrp 0 sap2-0: adjust the amount of fixed current from the fixed current source in the operational amplifier for the source driver. when the amount of fixed current is large, lcd driving ability and the display quality become high, but the current consumption is increased. adjust the fixed current considering the display quality and the current consumption. during no n- display, when sap2-0 = ? 000 ? , the current consumption can be reduced by ending the operational amplifier and step-up circuit operation. sap2 sap1 sap0 amount of current in operational amplifier 0 0 0 operation of the operational amplifier and step-up circuit stops. 0 0 1 small 0 1 0 small or medium 0 1 1 medium 1 0 0 medium or large 1 0 1 large 1 1 0 setting disabled 1 1 1 setting disabled bt2 ? 0: the output factor of step-up is switched. adjust scale factor of the step-up circuit by the voltage used. when the step-up operating frequency is high, the driving ability of the step-up circuit and the display quality become high, but the current consumption is increased. adjust the frequency considering the display quality and the current consumption. bt2 bt1 bt0 vlout1 output vlout2 output notes* 0 0 0 2 x vci1 3 x vci2 vlout2 = vci1 x six times 0 0 1 2 x vci1 4 x vci2 vlout2 = vci1 x eight times 0 1 0 3 x vci1 3 x vci2 vlout2 = vci1 x nine times 0 1 1 3 x vci1 2 x vci2 vlout2 = vci1 x six times 1 0 0 2 x vci1 vci1 + 2 x vci2 vlout2 = vci1 x five times 1 0 1 2 x vci1 vci1 + 3 x vci2 vlout2 = vci1 x seven times 1 1 0 step-up stopped 3 x vci2 vlout2 = vci2 x three times 1 1 1 step-up stopped 4 x vci2 vlout2 = vci2 x four times note: the step-up factors of vlout2 are derived from vci1 when vlout1 and vci2 are shorted. the conditions of vlout1 5.5v and vlout2 15.0v must be satisfied.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 48 dc2-0: the operating frequency in the step-up circuit is selected. when the step-up operating frequency is high, the driving ability of the step-up circuit and the display quality become high, but the current consumption is increased. adjust the frequency considering the display quality and the current consumption. dc2 dc1 dc0 step-up cycle in step-up circuit1 step-up cycle in step-up circuit 2/3/4 0 0 0 dcclk / 1 dcclk / 4 0 0 1 dcclk / 2 dcclk / 4 0 1 0 dcclk / 4 dcclk / 4 0 1 1 dcclk / 2 dcclk / 16 1 0 0 dcclk dcclk / 8 1 0 1 dcclk / 2 dcclk / 8 1 1 0 dcclk / 4 dcclk / 8 1 1 1 dcclk / 4 dcclk / 16 ap2 ? 0: the amount of fixed current in the operational amplifier for the power supply can be adjusted. when the amount of fixed current is large, the lcd driving ability and the display quality become high, but the current consumption is increased. adjust the fixed current considering the display quality and the current consumption. during no display, when ap2-0 = ? 000 ? , the current consumption can be reduced by ending the operational amplifier and step-up circuit operation. ap2 ap1 ap0 amount of current in operational amplifier 0 0 0 operation of the operational amplifier and step-up circuit stops. 0 0 1 small 0 1 0 small or medium 0 1 1 medium 1 0 0 medium or large 1 0 1 large 1 1 0 setting inhibited 1 1 1 setting inhibited slp: when slp = 1, the S6D0114 enters the sleep mode, where the internal display operations are halted except for the r-c oscillator, thus reducing current consumption. only the following instructions can be executed during the sleep mode. - power control (bt2 ? 0, dc3 ? 0, ap2 ? 0, slp, stb, vc2-0, cad, vr3-0, vrl3-0, vrh4-0, vcomg, vdv4- 0, and vcm4-0 bits) during the sleep mode, the other gram data and instructions cannot be updated although they are retained and g1 to g176 output is fixed to vss level, and register set-up is protected (maintained).
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 49 stb: when stb = 1, the S6D0114 enters the standby mode, where display operation completely stops, halting all the internal operations including the internal r-c oscillator. further, no external clock pulses are supplied. for details, see the standby mode section. only the following instructions can be executed during the standby mode. - standby mode cancel(stb = ? 0 ? ) - start oscillation cad: set this bit according to the structure for the tft-display retention volume. cad = 0: set this bit when the cst retention volume is structured. in this case, vgoff level is fixed to vgoffl level regardless of the vcom alternating drive. cad = 1: set this bit when the cadd retention volume is structured. at the vcom alternating drive, the vgoff voltage is output in the vgoffl voltage reference by the amount of vcom alternating amplitude. vrp4-0: control oscillation (positive polarity) of 64-grayscale. for details, see the oscillation adjusting circuit section. vrn4-0: control oscillation (negative polarity) of 64-grayscale. for details, see the oscillation adjusting circuit section.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 50 power control 3 (r12h) power control 4 (r13h) power control 5 (r14h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 0 0 0 0 0 0 0 0 0 0 0 0 0 vc2 vc1 vc0 w 1 0 0 0 0 vrl 3 vrl 2 vrl 1 vrl 0 0 0 0 pon vrh 3 vrh 2 vrh 1 vrh 0 w 1 0 0 vco mg vdv 4 vdv 3 vdv 2 vdv 1 vdv 0 0 0 0 vcm 4 vcm 3 vcm 2 vcm 1 vcm 0 vc2-0: adjust reference voltage of vreg1, vreg2out and vci out to optional rate of v ci . also, when vc2 = ? 1 ? , it is possible to stop the internal reference voltage generator. this leads to optional power on for vreg1out/vci out with regp and vreg2out with regn externally. vc2 vc1 vc0 internal reference voltage (regp) of vreg1out and vciout internal reference voltage (regn) of vreg2out 0 0 0 0.92 x vci 0.08 x vci 0 0 1 0.83 x vci 0.17 x vci 0 1 0 0.73 x vci 0.27 x vci 0 1 1 0.68 x vci 0.32 x vci 1 * * stops generation of the internal reference voltages of vreg1out and vciout (regp can be input externally) stops generation of the internal reference voltage of vreg2out (regn can be input externally). note: leave these settings open because the voltage other than that for halting the internal circuit is output for regp and regn . v rl3- 0: set magnification of amplification for vreg2out voltage (voltage for the reference voltage, vreg2 while generating vgoffout.) it allows magnifying the amplification of regn from 2 to 8.5 times. vrl 3 vrl 2 vrl 1 vrl 0 vreg2out voltage vrl 3 vrl 2 vrl 1 vrl 0 vreg2out voltage 0 0 0 0 -(vci ? regn) x 3.0 1 0 0 0 -(vci ? regn) x 6.5 0 0 0 1 -(vci ? regn) x 3.5 1 0 0 1 -(vci ? regn) x 7.0 0 0 1 0 -(vci ? regn) x 4.0 1 0 1 1 -(vci ? regn) x 7.5 0 0 1 1 -(vci ? regn) x 4.5 1 0 1 0 -(vci ? regn) x 8.0 0 1 0 0 -(vci ? regn) x 5.0 1 1 0 1 -(vci ? regn) x 8.5 0 1 0 1 -(vci ? regn) x 5.5 1 1 0 0 -(vci ? regn) x 9.0 0 1 1 0 -(vci ? regn) x 6.0 1 1 1 0 -(vci ? regn) x 9.5 0 1 1 1 stopped 1 1 1 1 stopped note: 1 ) these settings apply when the internal reference-voltage generation circuit is stopped and the vreg2out voltage is generated specifying regn as the reference voltage. 2 ) adjust the settings between the voltage set by (vci ? vc2-0) or the (vci ? regn) voltage and vrl0 to vrl3 so that the vreg2out voltage is higher than ? 16.0 v. 3 ) the vreg2out voltage is the factor when vci is the reference voltage.
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 51 pon: this is an operation-starting bit for the booster circuit 4. pon = 0 is to stop and pon = 1 to start operation. for further information about timing for adjusting to the pon = 1, please refer to the set up flow of p ower supply circuit . vrh 3 -0: set the amplified factor of the vreg1out voltage (the voltage for the reference voltage , vreg2 while generating vgoffout) . it allows to amplify from 1.45 to 2.85 times of regn input voltage. vrh 3 vrh 2 vrh 1 vrh 0 vreg1out voltage vrh 3 vrh 2 vrh 1 vrh 0 vreg1out voltage 0 0 0 0 regp x 1.45 times 1 0 0 0 regp x 2.175 times 0 0 0 1 regp x 1.55 times 1 0 0 1 regp x 2.325 times 0 0 1 0 regp x 1.65 times 1 0 1 1 regp x 2.475 times 0 0 1 1 regp x 1.75 times 1 0 1 0 regp x 2.625 times 0 1 0 0 regp x 1.80 times 1 1 0 1 regp x 2.700 times 0 1 0 1 regp x 1.85 times 1 1 0 0 regp x 2.775 times 0 1 1 0 regp x 1.90 times 1 1 1 0 regp x 2.850 times 0 1 1 1 stopped 1 1 1 1 stopped note: 1 ) these settings apply when the internal reference-voltage generation circuit is stopped and the vreg1out voltage is generated specifying regp as the reference voltage. 2 ) adjust the settings between the voltage set by vc2-0 or the regp voltage and vrh0 to vrh3 so that the vreg1out voltage is lower than 5.0 v. vcomg: when vcomg = 1, vcoml voltage can output to negative voltage (-5v). when vcomg = 0, vcoml voltage becomes vss and stops the amplifier of the negative voltage. therefore, low power consumption is accomplished. also, when vcomg = 0 and when vcom is driven in a/c, set up of the vdv4-0 is invalid. in this case, adjustment of vcom/vgoff a/c oscillation must be adjusted vcomh with vcm4-0. vdv4-0: set the alternating amplitudes of vcom and vgoff at the vcom alternating drive. these bits amplify vcom and vgoff 0.6 to 1.23 times the vreg1 voltage. when the vcom alternation is not driven, the settings become invalid. vdv 4 vdv 3 vdv 2 vdv 1 vdv 0 vcom amplitude vdv 4 vdv 3 vdv 2 vdv 1 vdv 0 vcom amplitude 0 0 0 0 0 vreg1 x 0.60 1 0 0 0 1 vreg1 x 1.08 0 0 0 0 1 vreg1 x 0.63 1 0 0 1 0 vreg1 x 1.11 0 0 0 1 0 vreg1 x 0.66 1 0 0 1 1 vreg1 x 1.14 : : : : : : 1 0 1 0 0 vreg1 x 1.17 0 1 1 0 0 vreg1 x 0.96 1 0 1 0 1 vreg1 x 1.20 0 1 1 0 1 vreg1 x 0.99 1 0 1 1 0 vreg1 x 1.23 0 1 1 1 0 vreg1 x 1.02 1 0 1 1 1 setting disabled 0 1 1 1 1 setting disabled 1 1 * * * setting disabled 1 0 0 0 0 vreg1 x 1.05 note: adjust the settings between vreg1 and vdv0 to vdv4 so that the vcom and vgoff amplitudes are lower than 6.0 v.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 52 vcm4-0: set the vcomh voltage (a high-level voltage at the vcom alternating drive). these bits amplify the vcomh voltage 0.4 to 0.98 times the vreg1 voltage. when vcom4-0 = 1, the adjustment of the internal volume stops, and vcomh can be adjusted from vcomr by an external resistor. vcm4 vcm3 vcm2 vcm1 vcm0 vcomh voltage 0 0 0 0 0 vreg1 x 0.40 times 0 0 0 0 1 vreg1 x 0.42 times 0 0 0 1 0 vreg1 x 0.44 times : : : : : : 0 1 1 0 0 vreg1 x 0.64 times 0 1 1 0 1 vreg1 x 0.66 times 0 1 1 1 0 vreg1 x 0.68 times 0 1 1 1 1 the internal volume stops and vcomh can be adjusted from vcomr by an external variable resistor. 1 0 0 0 0 vreg1 x 0.70 times 1 0 0 0 1 vreg1 x 0.72 times 1 0 0 1 0 vreg1 x 0.74 times : : : : : : 1 1 1 0 0 vreg1 x 0.94 times 1 1 1 0 1 vreg1 x 0.96 times 1 1 1 1 0 vreg1 x 0.98 times 1 1 1 1 1 the internal volume stops, and vcomh can be adjusted from vcomr by an external variable resistor. note: adjust the settings between vreg1 and vcm0 to vcm4 so that the vcomh voltage is lower than gvdd .
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 53 ram address set (r21h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 ad15 ad14 ad13 ad12 ad11 ad10 ad9 ad8 ad7 ad6 ad5 ad4 ad3 ad2 ad1 ad0 ad15 ? 0: initially set gram addresses to the address counter (ac). once the gram data is written, the ac is automatically updated according to the am and i/d bit settings. this allows consecutive accesses without resetting address. once the gram data is read, the ac is not automatically updated. gram address setting is not allowed in the standby mode. ensure that the address is set within the specified window address when rgb interface is in use ( rm=1), ad15-0 will be set at the falling edge of the vsync signal. when the internal clock operation and vsync interface (rm=1) are in use, ad15-0 will be set upon execution of an instruction. ad15 to ad0 gram setting ? 0000h ? to ? 0083 ? h bitmap data for g1 ? 0100h ? to ? 0183 ? h bitmap data for g2 ? 0200h ? to ? 0283 ? h bitmap data for g3 ? 0300h ? to ? 0383 ? h bitmap data for g4 : : : : : : ? ac00h ? to ? ac83 ? h bitmap data for g173 ? ad00h ? to ? ad83 ? h bitmap data for g174 ? ae00h ? to ? ae83 ? h bitmap data for g175 ? af00h ? to ? af83 ? h bitmap data for g176
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 54 write data to gram (r22h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 ram write data (wd17-0): pin assignment varies according to the interface method. (see the following figure for more information) wd15 wd14 wd13 wd12 wd11 wd10 wd9 wd8 wd7 wd6 wd5 wd4 wd3 wd2 wd1 wd0 w 1 when rgb-interface wd17-0: input data for gram can be expanded to 18 bits. the expansion format varies according to the interface method. the input data selects the grayscale level. after a write, the address is automatically updated according to am and i/d bit settings. the gram cannot be accessed in standby mode. when 16- or 8-bit interface is in use, the write data is expanded to 18 bits by writing the msb of the data to its lsb. when data is written to ram used by rgb interface via the system interface, please make sure that write data conflicts do not occur. when the 18-bit rgb interface is in use, 18-bit data is written to ram via pd17-0 and 262,144-colors are available. when the 16-bit rgb interface is in use, the msb is written to its lsb and 65,536-colors are available input data r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 rgb arrangement wd 17 wd 16 wd 15 wd 14 wd 13 wd 12 wd 11 wd 10 wd 9 wd 8 wd 7 wd 6 wd 5 wd 4 wd 3 wd 2 wd 1 wd 0 write to gram db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 db 0 figure 11 . 18-bit system interface (260k-color) input data r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 rgb arrangement wd 17 wd 16 wd 15 wd 14 wd 13 wd 12 wd 11 wd 10 wd 9 wd 8 wd 7 wd 6 wd 5 wd 4 wd 3 wd 2 wd 1 wd 0 write to gram db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 figure 12 . 16-bit system interface (65k-color)
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 55 input data r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 rgb arrangement wd 17 wd 16 wd 15 wd 14 wd 13 wd 12 wd 11 wd 10 wd 9 wd 8 wd 7 wd 6 wd 5 wd 4 wd 3 wd 2 wd 1 wd 0 write to gram db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 1st transmission db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 db 0 2nd transmission figure 13 . 9-bit system interface (260k-color) input data r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 rgb arrangement wd 17 wd 16 wd 15 wd 14 wd 13 wd 12 wd 11 wd 10 wd 9 wd 8 wd 7 wd 6 wd 5 wd 4 wd 3 wd 2 wd 1 wd 0 write to gram db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 1st transmission 2nd transmission figure 14 . 8-bit system interface (65k-color) input data rgb arrangement wd 17 wd 16 wd 15 wd 14 wd 13 wd 12 wd 11 wd 10 wd 9 wd 8 wd 7 wd 6 wd 5 wd 4 wd 3 wd 2 wd 1 wd 0 write to gram r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 pd 17 pd 16 pd 15 pd 14 pd 13 pd 12 pd 11 pd 10 pd 9 pd 8 pd 7 pd 6 pd 5 pd 4 pd 3 pd 2 pd 1 pd 0 figure 15 . 18-bit rgb interface (260k-color)
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 56 input data rgb arrangement wd 17 wd 16 wd 15 wd 14 wd 13 wd 11 wd 10 wd 9 wd 8 wd 7 wd 6 wd 5 wd 4 wd 3 wd 2 wd 1 write to gram r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 pd 17 pd 16 pd 15 pd 14 pd 13 pd 11 pd 10 pd 9 pd 8 pd 7 pd 6 pd 5 pd 4 pd 3 pd 2 pd 1 figure 16 . 16-bit rgb interface (65k-color) input data rgb arrangement wd 17 wd 16 wd 15 wd 14 wd 13 wd 12 wd 11 wd 10 wd 9 wd 8 wd 7 wd 6 wd 5 wd 4 wd 3 wd 2 wd 1 wd 0 write to gram r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 pd 17 pd 16 pd 15 pd 14 pd 13 pd 12 pd 11 pd 10 pd 9 pd 8 pd 7 pd 6 pd 5 pd 4 pd 3 pd 2 pd 1 pd 0 1st transmission 2nd transmission 3rd transmission figure 17 . 6-bit rgb interface (260k-color) table 23 . gram data and grayscale level gram data grayscale polarity gram data grayscale polarity gram data grayscale polarity gram data grayscale polarity rgb n p rgb n p rgb n p rgb n p 000000 v0 v63 010000 v16 v47 100000 v32 v31 110000 v48 v15 000001 v1 v62 010001 v17 v46 100001 v33 v30 110001 v49 v14 000010 v2 v61 010010 v18 v45 100010 v34 v29 110010 v50 v13 000011 v3 v60 010011 v19 v44 100011 v35 v28 110011 v51 v12 000100 v4 v59 010100 v20 v43 100100 v36 v27 110100 v52 v11 000101 v5 v58 010101 v21 v42 100101 v37 v26 110101 v53 v10 000110 v6 v57 010110 v22 v41 100110 v38 v25 110110 v54 v9 000110 v7 v56 010110 v23 v40 100110 v39 v24 110110 v55 v8 001000 v8 v55 011000 v24 v39 101000 v40 v23 111000 v56 v7 001001 v9 v54 011001 v25 v38 101001 v41 v22 111001 v57 v6 001010 v10 v53 011010 v26 v37 101010 v42 v21 111010 v58 v5 001011 v11 v52 011011 v27 v36 101011 v43 v20 111011 v59 v4 001100 v12 v51 011000 v28 v35 101100 v44 v19 111100 v60 v3 001101 v13 v50 011001 v29 v34 101101 v45 v18 111101 v61 v2 001100 v14 v49 011010 v30 v33 101100 v46 v17 111110 v62 v1 001101 v15 v48 011011 v31 v32 101101 v47 v16 111111 v63 v0
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 57 ram access via rgb interface & system interface all the data for display is written to the internal ram in the S6D0114 when rgb interface is in use. in this method, data, including that in both the motion picture area and the screen update frame, can only be transferred via rgb interface. in addition to using the high-speed write mode (hwm = 1) and the window address function , the power consumption can be reduced and high-speed access can be achieved while motion pictures are being displayed. data for display that is not in the motion picture area or the screen update frame can be written via the system interface. ram can be accessed via the system interface when rgb interface is in use. when data is written to ram during rgb interface mode, the enable bit should be low to stop data writing via rgb interface, because ram writing is always performed in synchronization with the dotclk input when enable is high. after this ram access via the system interface, a waiting time is needed for a write/read bus cycle before the next ram access starts via rgb interface. when a ram write conflict occurs, data writing is not guaranteed. vsync enable dotclk pd17-0 serial interface rm=0 index r22 address set index r22 writing display data except moving picture display area rm=0 address set index r22 moving picture display area 2001/01/01 00:00 still picture display area writing moving picture display area writing moving picture display area index set writing picture writing picture writing still picture display area figure 18 . ram access via rgb interface & system interface
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 58 read data from gram (r22h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 r 1 ram read data (rd17-0): pin assignment varies according to the interface method. (see the following figure for more information) rd1 7 ? 0: read 1 8 -bit data from the gram. when the data is read to the mcu , the first-word read immediately after the gram address setting is latched from the gram to the internal read-data latch. the data on the data bus (db15 ? 0) becomes invalid and the second-word read is normal. when bit processing, such as a logical operation, is performed within the S6D0114, only one read can be processed since the latched data in the first word is used. in case of 16-/8-bit interface, the lsb of color data will not be read. this function is not available in rgb interface mode. ouput data r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 gram data read data db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 db 0 rd 17 rd 16 rd 15 rd 14 rd 13 rd 12 rd 11 rd 10 rd 9 rd 8 rd 7 rd 6 rd 5 rd 4 rd 3 rd 2 rd 1 rd 0 figure 19 . 18-bit system interface for gram read r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 rd 17 rd 16 rd 15 rd 14 rd 13 rd 12 rd 11 rd 10 rd 9 rd 8 rd 7 rd 6 rd 5 rd 4 rd 3 rd 2 rd 1 rd 0 ouput data gram data read data figure 20 . 16-bit system interface for gram read
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 59 r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 1st transmission 2nd transmission ouput data gram data read data rd 17 rd 16 rd 15 rd 14 rd 13 rd 12 rd 11 rd 10 rd 9 rd 8 rd 7 rd 6 rd 5 rd 4 rd 3 rd 2 rd 1 rd 0 db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 figure 21 . 9-bit system interface for gram read r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 1st transmission 2nd transmission ouput data gram data read data rd 17 rd 16 rd 15 rd 14 rd 13 rd 12 rd 11 rd 10 rd 9 rd 8 rd 7 rd 6 rd 5 rd 4 rd 3 rd 2 rd 1 rd 0 db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 figure 22 . 8-bit system interface for gram read
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 60 sets the i/d, am, has/hse, and vsa/vea bits address: n set dummy read (invalid data) gram - > read data latch read (data of address n) read - data latch - > db17 - 0 address: m set dummy read (invalid data) gram - > read data latch read (data of address m) read - data latch - > db17 - 0 sets the i/d, am, has/hse, and vsa/vea bits address: n set dummy read (invalid data) gram - > read data latch write (data of address n) db17 - 0 - > gram automatic address update: n+ a dummy read (invalid data) gram - > read data latch write (data of address n+ a ) db17 - 0 - > gram first word second word first word second word first word second word first word second word i) data read to the microcomputer ii) logical operation processing sets the i/d, am, has/hse, and vsa/vea bits address: n set dummy read (invalid data) gram - > read data latch read (data of address n) read - data latch - > db17 - 0 address: m set dummy read (invalid data) gram - > read data latch read (data of address m) read - data latch - > db17 - 0 sets the i/d, am, has/hse, and vsa/vea bits address: n set dummy read (invalid data) gram - > read data latch write (data of address n) db17 - 0 - > gram automatic address update: n+ a dummy read (invalid data) gram - > read data latch write (data of address n+ a ) db17 - 0 - > gram first word second word first word second word first word second word first word second word i) data read to the microcomputer ii) logical operation processing in the S6D0114 figure 23 . gram read sequence
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 61 ram write data mask 1 (r23h) ram write data mask 2 (r24h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 0 0 wm11 wm10 wm9 wm8 wm7 wm6 0 0 wm5 wm4 wm3 wm2 wm1 wm0 w 1 0 0 0 0 0 0 0 0 0 0 wm 17 wm 16 wm 15 wm 14 wm 13 wm 12 wm1 7 ? 0: in writing to the gram, these bits mask writing in a bit unit. when wm1 7 = 1, this bit masks the write data of db1 5 and does not write to the gram. similarly, the wm1 4 to 0 bits mask the write data of db1 4 to 0 in a bit unit. for details, see the graphics operation function section. please make sure the write data to gram (18-bit) is masked. when 8-/16- bit interface is in use, the lsb of write data will not be read. when rgb interface is in use, this function is not available . wm 17 wm 16 wm 15 wm 14 wm 13 wm 12 wm 11 wm 10 wm 9 wm 8 wm 7 wm 6 wm 5 wm 4 wm 3 wm 2 wm 1 wm 0 r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 1 - pixel wm 17 wm 16 wm 15 wm 14 wm 13 wm 12 wm 11 wm 10 wm 9 wm 8 wm 7 wm 6 wm 5 wm 4 wm 3 wm 2 wm 1 wm 0 r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 1 - pixel figure 24 . write mask and ram write data
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 62 gamma control (r30h to r37h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 0 0 0 0 0 pkp 12 pkp 11 pkp 10 0 0 0 0 0 pkp 02 pkp 01 pkp 00 w 1 0 0 0 0 0 pkp 32 pkp 31 pkp 30 0 0 0 0 0 pkp 22 pkp 21 pkp 20 w 1 0 0 0 0 0 pkp 52 pkp 51 pkp 50 0 0 0 0 0 pkp 42 pkp 41 pkp 40 w 1 0 0 0 0 0 prp 12 prp 11 prp 10 0 0 0 0 0 prp 02 prp 01 prp 00 w 1 0 0 0 0 0 pkn 12 pkn 11 pkn 10 0 0 0 0 0 pkn 02 pkn 01 pkn 00 w 1 0 0 0 0 0 pkn 32 pkn 31 pkn 30 0 0 0 0 0 pkn 22 pkn 21 pkn 20 w 1 0 0 0 0 0 pkn 52 pkn 51 pkn 50 0 0 0 0 0 pkn 42 pkn 41 pkn 40 w 1 0 0 0 0 0 prn 12 prn 11 prn 10 0 0 0 0 0 prn 02 prn 01 prn 00 pkp52 ? 00: the g amma fine adjustment register for the positive polarity output prp12-00: the g radient adjustment register for the positive polarity output pkn52-00: the g amma fine adjustment register for the negative polarity output prn12-00: the g radient adjustment register for the negative polarity output for details, see the gamma adjustment function.
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 63 gate scan position (r40h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 0 0 0 0 0 0 0 0 0 0 0 scn4 scn3 scn2 scn1 scn0 scn 4-0: set the scanning starting position of the gate driver. scanning start position scn4 scn3 scn2 scn1 scn0 gs=0 gs=1 0 0 0 0 0 g1 g176 0 0 0 0 1 g9 g168 0 0 0 1 0 g17 g160 : : : : : : : : : : : : : : 1 0 0 1 1 g153 g24 1 0 1 0 0 g161 g16 1 0 1 0 1 g169 g8 g1 g160 g161 g176 g1 g160 g161 g176 g16 g17 gs = 0 nl = 10010 scn4-0 = 00000 gs = 1 nl = 10010 scn4-0 = 00010 note: set nl4-0 on the gate scan end that does not exceed value 176 figure 25 . relationship between nl and scn set up value
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 64 vertical scroll control (r41h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 0 0 0 0 0 0 0 0 vl7 vl6 vl5 vl4 vl3 vl2 vl1 vl0 vl7-0: specify scroll length at the scroll display for vertical smooth scrolling. any raster-row from the first to 176 th can be scrolled for the number of the raster-row. after 176 th raster-row is displayed, the display restarts from the first raster-row. the display-start raster-row (vl7-0) is valid when vle1 = 1 or vle2 = 1. the raster-row display is fixed when vle2-1 = 00. vl7 vl6 vl5 vl4 vl3 vl2 vl1 vl0 scroll length 0 0 0 0 0 0 0 0 0 raster-row 0 0 0 0 0 0 0 1 1 raster-row 0 0 0 0 0 0 1 0 2 raster-row . . . . . . . . 1 0 1 0 1 1 1 0 174 raster-row 1 0 1 0 1 1 1 1 175 raster-row note: don ? t set any higher raster-row than 175 ( ? af ? h) 1 st screen driving position (r42h) 2 nd screen driving position (r43h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 se17 se16 se15 se14 se13 se12 se11 se10 ss17 ss16 ss15 ss14 ss13 ss12 ss11 ss10 w 1 se27 se26 se25 se24 se23 se22 se21 se20 ss27 ss26 ss25 ss24 ss23 ss22 ss21 ss20 ss17 ? 1 0: specify the driving start position for the first screen in a line unit. the lcd driving starts from the ? set value +1 ? gate driver. se17 ? 1 0: specify the driving end position for the first screen in a line unit. the lcd driving is performed to the 'set value + 1' gate driver. for instance, when ss17 ? 10 = 07 h and se17 ? 10 = 10 h are set, the lcd driving is performed from g8 to g17, and non- display driving is performed for g1 to g7, g18, and others. ensure that ss17 ? 10 se17 ? 10 af h . for details, see the screen-division driving function section. ss27 ? 1 0: specify the driving start position for the second screen in a line unit. the lcd driving starts from the 'set value + 1' gate driver. the second screen is driven when spt = 1. se27 ? 2 0: specify the driving end position for the second screen in a line unit. the lcd driving is performed to the 'set value + 1' gate driver. for instance, when spt = 1, ss27 ? 20 = 20 h , and se27 ? 20 = af h are set, the lcd driving is performed from g33 to g80. ensure that ss17 ? 10 se17 ? 10 ss27 ? 20 se27 ? 20 afh . for details, see the screen-division driving function section.
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 65 horizontal ram address position (r16h) vertical ram address position (r17h) r/w rs db15 db14 db13 db12 db11 db10 db9 db8 db7 db6 db5 db4 db3 db2 db1 db0 w 1 hea 7 hea 6 hea 5 hea 4 hea 3 hea 2 hea 1 hea 0 hsa 7 hsa 6 hsa 5 hsa 4 hsa 3 hsa 2 hsa 1 hsa 0 w 1 vea 7 vea 6 vea 5 vea 4 vea 3 vea 2 vea 1 vea 0 vsa 7 vsa 6 vsa 5 vsa 4 vsa 3 vsa 2 vsa 1 vsa 0 hsa7-0/hea7-0: specify the horizontal start/end positions of a window for access in memory. data can be written to the gram from the address specified by hea 7-0 from the address specified by hsa7-0. note that an address must be set before ram is written. ensure 00 h hsa7-0 hea7-0 83 h . vsa7-0/vea7-0: specify the vertical start/end positions of a window for access in memory. data can be written to the gram from the address specified by vea7-0 from the address specified by vsa7-0. note that an address must be set before ram is written. ensure 00 h vsa7-0 vea7-0 afh. window address 0000 h af83h hsa hea vsa vea gram address space window address setting range ? 00 ? h hsa7-0 hea7-0 ? 83 ? h ? 00 ? h vsa7-0 vea7-0 ? af ? h note: 1. ensure that the window address area is within the gram address space 2. in high-speed write mode, data are written to gram in four-words. thus, dummy write operations should be inserted depending on the window address area. for details, see the high-speed burst ram write function section figure 26 . window address setting range
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 66 reset function the S6D0114 is internally initialized by reset input. the reset input must be held for at least 1 ms. do not access the gram or initially set the instructions until the r-c oscillation frequency is stable after power has been supplied (10 ms). instruction set initialization 1. start oscillation executed 2. driver output control (nl4 ? 0 = 10101, ss = 0, cs = 0 , epl=0 ) 3. lcd driving ac control (fld1-0 = 01, b/c = 0, eor = 0, nw5 ? 0 = 00000) 4 . power control 1 (sap2-0 = 000, bt2-0 = 000, dc2 ? 0 = 000, ap2 ? 0 = 000: lcd power off, slp = 0, stb = 0: standby mode off) 5. power control 2 (cad = 0, vrn4-0 = 0000 0 , vrp4-0 = 0000 0) 6. entry mode set (hwm = 0, i/d1-0 = 11: increment by 1, am = 0: horizontal move, lg2 ? 0 = 000: replace mode , bgr=0 ) 7. compare register (cp1 7 ? 0: 00/ 0000 / 0000 / 0000 / 0000) 8. display control 1 (pt1-0 = 00, vle2 ? 1 = 00: no vertical scroll, spt = 0, gon = 0, dte = 0, cl = 0: 260k- color mode, rev = 0, d1 ? 0 = 00: display off) 9. display control 2 (fp3-0=0101, bp3-0=0011, blp13-0=0010, blp23-0=0010 ) 10 . frame cycle control (no1-0 = 00, sdt1-0 = 00, eq1-0 = 00: no equaliz ation , div1-0 = 00: 1-divided clock, rtn3-0 = 0000: 16 clock cycle in 1h period) 11. external display interface (rim1-0=00:18-bit rgb interface, dm1-0=00: operated by internal clock, rm=0: system interface) 1 2 . power control 3 (vc2-0 = 000) 1 3 . power control 4 (vrl3-0 = 0000, pon=0, vrh 3 -0 = 0000 ) 1 4 . power control 5 (vcomg = 0, vdv4-0 = 00000, vcm4-0 = 00000 ) 15 . ram address set (ad15 ? 0 = 0000 h ) 16 . ram write data mask (wm15 ? 0 = 0000 h : no mask) 17 . gamma control (pkp02 ? 00 = 000, pkp12 ? 10 = 000, pkp22 ? 20 = 000, pkp32 ? 30 = 000, pk42 ? 40 = 000, pkp52 ? 50 = 000, prp02 ? 00 = 000, prp12 ? 10 = 000) (pkn02 ? 00 = 000, pkn12 ? 10 = 000, pkn22 ? 20 = 000, pkn32 ? 30 = 000, pkn42 ? 40 = 000, pkn52 ? 50 = 000, prn02 ? 00 = 000, prn12 ? 10 = 000) 1 8 . gate scanning starting position (scn4-0 = 00000) 1 9 . vertical scroll (vl7 ? 0 = 0000000) 20. 1st screen division (se17-10 = 11111111, ss17-10 = 00000000) 21 . 2nd screen division (se27-20 = 11111111, ss27-20 = 00000000) 22 . horizontal ram address position (hea7-0 = 10000011, hsa7-0 = 00000000) 23 . vertical ram address position (vea7-0 = 101011 1 1, vsa7-0 = 00000000) gram data initialization gram is not automatically initialized by reset input but must be initialized by software while display is off (d1 - 0 = 00). output pin initialization 1. lcd driver output pins (source output ) : output vss level (gate output) : output vgoff level 2. oscillator output pin (osc2): outputs oscillation sign
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 67 power supply circuit the following f igure shows a configuration of the voltage generation circuit for S6D0114 . the step-up circuits consist of step-up circuits 1 to 4. step-up circuit1 doubles or triples the voltage supplied to vci1, and that voltage is doubled, tripled, or quadrupled in step-up circuit2. step-up circuit3 reverses the vgh level with reference to vss or vbs and generates the vgl level. step-up circuit 4 reverses the vci level with reference to vss and generates the vcl level. these step-up circuits generate power supplies av dd, gvdd, vgh, vgl, vgoff, and vcom. reference voltages gvdd, vcom, and vgoff for the grayscale voltage are amplified in amplification circuits 1 and 2 from the internal- voltage adjustment circuit or the regp or regn voltage, and generate each level depending on that voltage. connect vcom to the tft panel. amplfiication circuit2 (vgoff adjustment) amplification circuit1 (gvdd adjustment) vcomh adjustment circuit vcom amplitude adjustment circuit gvdd voltage adjustment circuit regulator vciout vci vci vcomr gvdd output amplifier gvdd step-up circuit 1 step-up circuit 2 step-up circuit 3 vreg2 out vreg1 out vreg2 vreg1 regp regn adjust vcomh voltage (when using an external variable resistor) vci when using vciout vci1 c11- c11+ c12- c12+ vlout1 ddvdh vci2 c21- c21+ c22- c22+ c23- c23+ vlout2 vgh vci3 c31- c31+ vlout3 vgl vci4 c41- c41+ vlout4 vcl vgl vgh avdd vcomh output amplifier vcoml output amplifier vcomh vcom vcoml vgoffh output amplifier vgoffl output amplifier vgoffh vgoffout vgoffl vgoffh amplitude adjustment circuit vss vss vdd vci step-up circuit 4 figure 27 . configuration of the internal power-supply circuit notes: use the 1uf capacitor.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 68 pattern diagrams for voltage setting the following f igure shows a pattern diagram for the voltage setting and an example of waveforms . vgh(+7 ~ +20v) avdd(+3.5 ~ +5.5v) ddvdh vreg1out gvdd(+3.0 ~ +5.0v) vdh vcomh(+3.0 ~ vdh) vcom4-0 vdv4-0 bt2-0 vrh3-0 vci1 (-1 times) bt2-0 vrl3-0 (-1 times) vcoml(vcl+0.5 to 1.0v) vcl vgoffh(to -5.0v) vgoffl (vgl+0.5 to -16.0v) vgl(-9 to -16.5v) vreg2out vci(2.5v ~ 3.3v) vdd(1.8v ~ 3.3v) vss(0v) vc2-0 note: adjust the conditions of avdd-gvdd>0.5v, vcoml-vcl>0.5v, and vgoff-vgl>0.5v with loads because they differ depending on the display load to be driven. in addition, vci can be directly input to vci1. vgh gvdd(vdh) vcomh vcoml vgoffh vgoffl vcom sn(source output) gn(gate output) figure 28 . pattern diagram and an example of waveforms
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 69 set up flow of power supply apply the power in a sequence as shown in the following figure . the stable time of the oscillation circuit, step-up circuit, and operational amplifier depend on the external resistor or capacitance. 10ms or more (stable time of the oscillation circuit) power supply (vdd on) power-on reset and display off 1ms issues instructions for power supply setting (1) bits for display off. dte=0 d1-0=00 gon=0 pon=0 normal display bits for display on: dte =1, d1- 0=11, gon=1 bits for power-supply initial setting: vcom, vc2- 0, vrh3- 0, cad, vrl3- 0, vcm4-0, vdv4- 0, vrn4-0, vrp4-0 (setting of the source- driver grayscale voltage) issues instruction for power supply setting (2) bits for power-supply operation start setting: bt2-0, dc2- 0, ap2-0 bits for source-driver operational amplifier operaton-start setting: sap2-0 bits for step-up circuit3 operation start pon=1 issues instruction for power supply setting (3) display off bits for display off: dte =0, d1- 0=00, gon=0 instruction for power supply setting(1) bits for source-driver operational amplifier operation-stop setting: sap2-0 instruction for power supply setting(2) bits for power supply stop setting: ap2-0 for operational amplifier, dc2-0 for step-up circuit display off sequence* power supply (vdd off) issues instruction for other mode setting display-on sequence* diplay on bits for display on: dte =1, d1- 0=11, gon=1 50ms or more (stable times of step-up circuit 1 and 2) 200ms or more (stable time of the step- up operational amplifier) power-on sequence power-off sequence figure 29 . set up flow of power supply
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 70 voltage regulation function the S6D0114 have internal voltage regulator. voltage regulation function is controlled by pregb pin. if pregb= ? h ? , voltage regulation is stopped. pregb= ? l ? enables internal voltage regulation function. by use of this function, internal logic circuit damage can be prohibited. furthermore , power consumption also be obtained. detailed function description and application setup is described in the following diagram. voltage regulator internal vdd (1.9v) vdd3 (external power) range: 2.5~3.3v rvdd pregb pregb= 'l' : regulator on vdd input level shifter internal vdd internal logic gnd (a) voltage regulation function enabled voltage regulator internal vdd input pregb level shifter internal vdd internal logic vdd (external power) 1.8~2.5v vdd3 rvdd pregb= 'h' : regulator off (b) voltage regulation function disabled figure 30 . voltage regulation function
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 71 interface specification the S6D0114 incorporates a system interface, which is used to set instructions, and an external display interface, which is used to display motion pictures. selecting these interfaces to match the screen data (motion picture or still picture) enables efficient transfer of data for display. the external display interface includes rgb interface and vsync interface. this allows flicker-free screen update. when rgb interface is selected, the synchronization signals (vsync, hsync, and dotclk) are available for use in operating the display. the data for display (pd17-0) is written according to the values of the data enable signal (enable) and data valid signal (vld), in synchronization with the vsync, hsync, and dotclk signals. in addition, using the window address function enables rewriting only to the internal ram area to display motion pictures. using this function also enables simultaneously display of the motion picture area and the ram data that was written. while displaying motion pictures, the data for display should be written in high-speed write mode, which achieves both low power consumption and high-speed access via rgb interface or vsync interface. the internal display operation is synchronized with the frame synchronization signal (vsync) in vsync interface mode. when writing to the internal ram is done within the required time after the falling edge of vsync, motion pictures can be displayed via the conventional interface. there are some limitations on the timing and methods of writing to ram. see the section on the external display interface. the S6D0114 has four operation modes for each display state. these settings are specified by control instructions for external display interface. transitions between modes should follow the transition flow. table 24 . display operation mode and ram access selection operation mode ram access selection (rm) display operation mode (dm1-0) internal clock operation (displaying still picture) system interface (rm=0) internal clock operation (dm1-0=00) rgb interface (1) (displaying motion picture) rgb interface (rm=1) rgb interface (dm1-0=01) rgb interface (2) (rewriting still picture while displaying motion pictures) system interface (rm=0) rgb interface (dm1-0=01) vsync interface (displaying motion pictures) system interface (rm=0) vsync interface (dm1-0=10) notes: 1) instruction registers can only be set via system interface. 2) rgb interface and vsync interfa ce cannot be used at the same time. 3) rgb interface mode cannot be set during operations. 4) for mode transitions, see the section on the external display interface. 5) rgb interface vsync interface modes should be used in high-speed write mode (hwm = 1).
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 72 system interface S6D0114 is enabling to set instruction and access to ram by selecting im3/2/1/0 pin in the system interface mode. table 25 . im bits and system interface im3 im2 im1 im0 system interface db pin 0 0 0 0 68-system 16-bit interface db17 to10, 8 to1 0 0 0 1 68-system 8-bit interface db17 to10 0 0 1 0 80-system 16-bit interface db17 to10, 8 to1 0 0 1 1 80-system 8-bit interface db17 to10 0 1 0 * serial peripheral interface (spi) db1 to 0 0 1 1 * setting disabled - 1 0 0 0 68-system 18-bit interface db17 to 0 1 0 0 1 68-system 9-bit interface db17 to 9 1 0 1 0 80-system 18-bit interface db17 to 0 1 0 1 1 80-system 9-bit interface db17 to 9 1 1 * * setting disabled - 68/80-system 18-bit bus interface setting the im 3/ 2/1/0 (interface mode) to the vdd3/vss / vss / vss level allows 68-system 18 -bit parallel data transfer. setting the im 3/ 2/1/0 to the vdd 3/gnd /vdd 3 /gnd level allows 80-system 18-bit parallel data transfer. mpu csn a1 / wr / rd d17-d0 S6D0114 csb rs / wr / rd db17-db0 18 figure 31 . interface with the 18-bit microcomputer 68/80-system 18-bit interface data format db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 db 0 input ib 15 ib 14 ib 13 ib 12 ib 11 ib 10 ib 9 ib 8 ib 7 ib 6 ib 5 ib 4 ib 3 ib 2 ib 1 ib 0 instruction figure 32 . instruction format for 18-bit interface
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 73 db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 db 0 input r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 gram data 1- pixel *262,144 - color display is available in 18-bit system interface. figure 33 . ram data write format for 18-bit interface 68/80-system 16-bit bus interface setting the im 3/ 2/1/0 (interface mode) to the vss/vss / vss / vss level allows 68-system 16 -bit parallel data transfer. setting the im 3/ 2/1/0 to the vss/vss / vdd3 / vss level allows 80-system 1 6 -bit parallel data transfer. mpu csn * a1 hwr* ( rd*) d15-d0 S6D0114 csb /wr / rd db17-10, db8-1 16 figure 34 . interface with the 16-bit microcomputer 68/80-system 16-bit interface data format input db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 ib 15 ib 14 ib 13 ib 12 ib 11 ib 10 ib 9 ib 8 ib 7 ib 6 ib 5 ib 4 ib 3 ib 2 ib 1 ib 0 instruction instruction code input db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 ib 15 ib 14 ib 13 ib 12 ib 11 ib 10 ib 9 ib 8 ib 7 ib 6 ib 5 ib 4 ib 3 ib 2 ib 1 ib 0 instruction instruction code figure 35 . instruction format for 16-bit interface input db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 8 db 7 db 6 db 5 db 4 db 3 db 2 db 1 r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 gram data 1- pixel *65,536- color display is available in the 16-bit system interface. figure 36 . ram data write format for 16-bit interface
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 74 68/80-system 9-bit bus interface setting the im 3/ 2/1/0 (interface mode) to the vdd3/vss / vss /vdd 3 level allows 68-system 9 -bit parallel data transfer using pins db1 7 ? db 9 . setting the im 3/2/ 1/0 to be vdd3/vss/ vdd 3 /vdd 3 level allows 80-system 9 -bit parallel data transfer. the 16-bit instructions and ram data are divided into nine upper/lower bits and the transfer starts from the upper nine bits. fix unused pins db 8 ? db0 to the vdd 3 or vss level. note that the upper bytes must also be written when the index register is written. mpu csn * a1 hwr* ( rd*) d15 - d0 s6d0101 cs* rs wr* ( rd*) db17 - db9 9 db8 - db0 9 mpu csn * a1 hwr* ( rd*) d15 - d0 s6d0101 cs* rs wr* ( rd*) db17 - db9 9 db8 - db0 9 figure 37 . interface to 9-bit microcomputer 68/80-system 9-bit interface data format input ib 15 ib 14 ib 13 ib 12 ib 11 ib 10 ib 9 ib 8 ib 7 ib 6 ib 5 ib 4 ib 3 ib 2 ib 1 ib 0 instruction instruction code 1 st transfer(upper) 2 nd transfer(lower) db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 input ib 15 ib 14 ib 13 ib 12 ib 11 ib 10 ib 9 ib 8 ib 7 ib 6 ib 5 ib 4 ib 3 ib 2 ib 1 ib 0 instruction instruction code 1 st transfer(upper) 2 nd transfer(lower) db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 figure 38 . instruction format for 9-bit interface input r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 gram data 1- pixel *262,144- color display is available in the 9-bit system interface 1 st transfer(upper) 2 nd transfer(lower) db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 db 9 figure 39 . ram data write format for 9-bit interface
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 75 note: transfer synchronization function for a 9-bit bus interface the s6d01 14 supports the transfer synchronization function, which resets the upper/lower counter to count upper/lower 9 -bit data transfer in the 9 -bit bus interface. noise causing transfer mismatch between the nine upper and lower bits can be corrected by a reset triggered by consecutively writing a ? 00 ? h instruction four times. the next transfer starts from the upper nine bits. executing synchronization function periodically can recover any runaway in the display system. ? 00 ? h ? 00 ? h ? 00 ? h ? 00 ? h upper or lower upper lower rs rd wr db17 ~db9 (1) (2) (3) (4) 9 - bit transfer sync. ? 00 ? h ? 00 ? h ? 00 ? h ? 00 ? h upper or lower upper lower rs rd wr db17 ~db9 (1) (2) (3) (4) 9 - bit transfer sync. figure 40 . 9-bit transfer synchronization 68/80-system 8-bit bus interface setting the im 3/ 2/1/0 (interface mode) to the vss/vss / vss /vdd 3 level allows 68-system 8 -bit parallel data transfer. setting the im 3/2/ 1/0 to the vss/vss/ vdd 3 /vdd 3 level allows 80-system 8 -bit parallel data transfer. the 16-bit instructions and ram data are divided into eight upper/lower bits and the transfer starts from the upper eight bits. fix unused pins db 9 ? db0 to the vdd 3 or vss level. note that the upper bytes must also be written when the index register is written. mpu csn a1 / wr / rd d7-d0 S6D0114 csb rs / wr / rd db15-db8 8 db7-db0 8 figure 41 . interface with the 8-bit microcomputer
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 76 68/80-system 8-bit interface data format input db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 ib 15 ib 14 ib 13 ib 12 ib 11 ib 10 ib 9 ib 8 ib 7 ib 6 ib 5 ib 4 ib 3 ib 2 ib 1 ib 0 instruction instruction code 1 st transfer(upper) 2 nd transfer(lower) db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 input db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 ib 15 ib 14 ib 13 ib 12 ib 11 ib 10 ib 9 ib 8 ib 7 ib 6 ib 5 ib 4 ib 3 ib 2 ib 1 ib 0 instruction instruction code 1 st transfer(upper) 2 nd transfer(lower) db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 figure 42 . instruction format for 8-bit interface input db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 gram data 1- pixel 1 st transfer(upper) 2 nd transfer(lower) db 17 db 16 db 15 db 14 db 13 db 12 db 11 db 10 figure 43 . ram data write format for 8-bit interface note: transfer synchronization function for an 8-bit bus interface the s6d01 14 supports the transfer synchronization function, which resets the upper/lower counter to count upper/lower 8-bit data transfer in the 8-bit bus interface. noise causing transfer mismatch between the eight upper and lower bits can be corrected by a reset triggered by consecutively writing a ? 00 ? h instruction four times. the next transfer starts from the upper eight bits. executing synchronization function periodically can recover any runaway in the display system ? 00 ? h ? 00 ? h ? 00 ? h ? 00 ? h upper or lower upper lower rs rd wr db17 ~db10 (1) (2) (3) (4) 8 - bit transfer sync. ? 00 ? h ? 00 ? h ? 00 ? h ? 00 ? h upper or lower upper lower rs rd wr db17 ~db10 (1) (2) (3) (4) 8 - bit transfer sync. figure 44 . 8-bit transfer synchronization
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 77 serial data transfer setting the im 3 pin to the vss level allows serial peripheral interface (spi) transfer, using the chip select line (cs*), serial transfer clock line (scl), serial input data (sdi), and serial output data (sdo). for a serial interface, the im0/id pin function uses an id pin. if the chip is set up for serial interface, the db1 7 -2 pins that are not used must be fixed at vdd 3 or vss . the S6D0114 initiates serial data transfer by transferring the start byte at the falling edge of cs b input. it ends serial data transfer at the rising edge of cs b input. the S6D0114 is selected when the 6-bit chip address in the start byte matches the 6-bit device identification code that is assigned to the S6D0114 . w hen selected, the S6D0114 receives the subsequent data string. the lsb of the identification code can be determined by the id pin. the five upper bits must be 011 1 0. two different chip addresses must be assigned to a single S6D0114 because the seventh bit of the start byte is used as a register select bit (rs): that is, when rs = 0, data can be written to the index register or status can be read, and when rs = 1, an instruction can be issued or data can be written to or read from ram. read or write is selected according to the eighth bit of the start byte (r/w bit). the data is received when the r/w bit is 0, and is transmitted when the r/w bit is 1. after receiving the start byte, the S6D0114 receives or transmits the subsequent data byte-by-byte. the data is transferred with the msb first. all S6D0114 instructions are 16 bits. two bytes are received with the msb first (db1 7 to 0), then the instructions are internally executed. after the start byte has been received, the first byte is fetched as the upper eight bits of the instruction and the second byte is fetched as the lower eight bits of the instruction. four bytes of ram read data after the start byte are invalid. the S6D0114 starts to read correct ram data from the fifth byte. table 26 . start byte format transfer bit s 1 2 3 4 5 6 7 8 device id code rs r/w start byte format transfer start 0 1 1 1 0 id note : id bit is selected by the im0/id pin. table 27 . rs and r/w bit function rs rw function 0 0 set index register 0 1 read status 1 0 writes instruction or ram data 1 1 reads instruction or ram data ib 15 ib 14 ib 13 ib 12 ib 11 ib 10 ib 9 ib 8 ib 7 ib 6 ib 5 ib 4 ib 3 ib 2 ib 1 ib 0 instruction instruction code d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 input 1 st transfer(upper) 2 nd transfer(lower) ib 15 ib 14 ib 13 ib 12 ib 11 ib 10 ib 9 ib 8 ib 7 ib 6 ib 5 ib 4 ib 3 ib 2 ib 1 ib 0 instruction instruction code d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 input 1 st transfer(upper) 2 nd transfer(lower) figure 45 . instruction format for serial data transfer
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 78 input r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 gram data 1 - pixel *65,536 - color display is possible using the serial interface. 1 st transfer(upper) 2 nd transfer(lower) d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 input r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 gram data 1 - pixel *65,536 - color display is possible using the serial interface. 1 st transfer(upper) 2 nd transfer(lower) d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 figure 46 . ram data write format for serial data transfer
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 79 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 0 1 1 1 0 id r rw db db db db db db db db db db db db db db db db 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 device id rs r/w start byte index register setting instruction ram data write db db db db db db db db db db db db db db db db 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 status read instruction read ram data read a) timing basic data transfer through clock synchronized serial bus interface transfer start transfer end b) timing of consecutive data-transfer through clock-synchronized serial bus interface start byte instruction 1: upper instruction 2: lower instruction 2: upper 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 instruction 1: execution time end start note: the first byte after the start byte is always the upper eight bits. scl (input) sdi (input) sdo (output) scl (input) sdi (input) cs* (input) cs* (input) c) ram-data read-transfer timing start byte rs=1 r/w=1 dummy read 1 dummy read 2 dummy read 3 dummy read 4 dummy read 5 ram read: upper 8-bits ram read: lower 8-bits start end note: 5-byte of ram read data after the start byte are invalid. the S6D0114 starts to read the correct ram data from sixth byte scl (input) sdi (input) sdo (output) cs* (input) figure 47 . procedure for transfer on clock synchronized serial bus interface
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 80 cs* (input) start byte rs=1 r/w=1 sdi (input) dummy read 1 status read upper 8-bit status read lower 8-bit start end note: 2-byte of the ram read after the start byte is invalid. the S6D0114 starts to read the correct ram data from the third data. d) status read/instruction read sdo (output) figure 48 . procedure for transfer on clock synchronized serial bus interface (continued)
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 81 vsync interface the S6D0114 incorporates vsync interface, which enables motion pictures to be displayed with only the conventional system interface and the frame synchronization signal (vsync). this interface requires minimal changes from the conventional system to display motion pictures. lcdc /mpu S6D0114 vsync csb rs /wr db17-10, 8-1 16 figure 49 . vsync interface when dm1-0= ? 10 ? and rm= ? 0 ? , vsync interface is available. in this interface the internal display operation is synchronized with vsync. data for display is written to ram via the system interface with higher speed than for internal display operation. this method enables flicker-free display of motion pictures with the conventional interface. display operation can be achieved by using the internal clock generated by the internal oscillator and the vsync input. because all the data for display is written to ram, only the data to be rewritten is transferred. this method reduces the amount of data transferred during motion picture display operation. the higher-speed write mode (hwm= ? 1 ? ) achieves both low power consumption and high-speed access. writing to screen writing to screen vsync gram data write via system interface displaying operation in synchronization with the internal clock figure 50 . moving picture data transfer via vsync interface vsync interface requires taking the minimum speed for ram writing via the system interface and the frequency of the internal clock into consideration. ram writing should be performed with higher speed than the result obtained from the calculation shown below.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 82 ------------------------------------------------------------------------------------------------------------------------------------------------------- internal clock frequency (fosc) [hz] = frame freq. (d isplay raster-row (nl) + front porch (fp) + back porch (bp)) 16- c lock fluctuation m inimum speed for ram writing [hz] > 176 display raster-row (nl) / {(( back porch (bp) + d isplay raster-row (nl) ? margin) 16 clock) / fosc} note : when ram writing does not start immediately after the falling edge of vsync, the time between the falling edge of vsync and the ram writing start timing must also be considered. ------------------------------------------------------------------------------------------------------------------------------------------------------- an example is shown below. example display size 132rgb 176 raster-rows display line number 176 rast er-row (nl=10101) back/front porch 3/5 raster-rows (bp=0011/fp=0101) frame frequency 60hz internal clock frequency (fosc) [hz]= 60 hz (176 + 2 + 14) 16 clock 1.1 / 0.9 = 216 khz notes : 1. calculating the internal clock frequency requires conside ring the fluctuation. in the above case a 10% fluctuation within the vsync period is assumed. 2. the fluctuation includes lsi production variation and air temperature fluctuation. other fluctuations, including those for the external resistors and the supplied power, are not included in this example. please keep in mind that a margin for these factors is also needed. minimum speed for ram writing [hz] > 132 176 / {((3 + 176 ? 5) raster-rows 16 clock) / 216khz} = 1.8 mhz notes : 3. in this case ram wri ting starts immediately after the falling edge of vsync. 4. the margin for display raster -row should be two raster-rows or more at the completion of ram writing for one frame. therefore, when ram writing starting immediately after the falling edge of vsync is performed at 1.8 mhz or more, the data for display can be rewritten before display operation starts. this means that flicker-free display operation is achieved. display (176-line) blanking period back porch (5-line) front porch (3-line) ram write displaying operation vsync [ line] 176 0 executed line 2.32 12.90 13.04 16.74 (60 hz) back porch 14h vsync ram write(10mhz) 23232 times ram write 1.8mhz displaying operation rc oscillation 10% displaying operation figure 51 . operation for vsync interface
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 83 usage on vsync interface 1. the example above is a calculated value. please keep in mind that a margin for these factors is also needed. because production variation of the internal oscillator requires consideration. 2. the example above is a calculated value of rewriting the whole screen. a limitation of the motion picture area generates a margin for the ram write speed. (20- line) (20- line) moving picture display (200-line) example: moving picture display area(20~156-line) back porch (3-line) front porch (5-line) ram write [ line] 176 0 executed line 16.74 (60 hz) [ ms] back porch 14h vsync ram write 1.8mhz displaying operation rc oscillation 10% displaying operation 156 9.97 13.04 20 figure 52 . limitation of motion picture area 3. during the period between the completion of displaying one frame data and the next vsync signal, the display will remain front porch period. 4. transition between the internal operating clock mode (dm1-0= ? 00 ? ) and vsync interface mode will be valid after the completion of the screen, which is displayed when the instruction is set.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 84 hwm=1, am=0 address setting vsync interface mode setting (dm1-0=10, rm=0) index register setting(r22h) wait more than 1 frame vsync interface ram data writing vsync interface operation internal clock mode setting (dm1-0=00, rm=0) wait more than 1 frame internal clock operation internal clock operation display operation in synchronization with the internal clock the value set in dm1- 0 and rm will be valid after completion of 1- frame display. display operation in synchronization with vsync note: when the interface mode is switched, vsync should be input before setting dm1-0 and rm bit. internal clock operation =>vsync interface wait more than 1 frame internal clock mode setting (dm1-0=00, rm=0) internal clock operation vsync interface operation display operation in synchronization with vsync the value set in dm1- 0 and rm will be valid after completion of 1- frame display. display operation in synchronization with the internal clock note: when switching to internal clock mode, please keep supplying vsync signal for more than 1 frame. vsync interface => internal clock operation figure 53 . transition between the internal operating clock mode and vsync interface mode 5. partial display, vertical scroll, and interlaced driving functions are not available on vsync interface mode. 6. the vsync interface is performed by the method above, therefore , am bit should be 0.
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 85 external display interface the following interfaces are available as external display interface. it is determined by bit setting of rim1-0. ram accesses can be performed via the rgb interface. table 28 . rim bits rim1 rim0 rgb interface pd pin 0 0 18-bit rgb interface pd17 to 0 0 1 16-bit rgb interface pd17 to13, 11 to 1 1 0 6-bit rgb interface pd17 to12 1 1 setting disabled rgb interface the rgb interface is performed in synchronization with vsync, hsync, and dotclk. combining the function of the high-speed write mode and the window address enables transfer only the screen to be updated and reduce the power consumption. moving picture display area moving picture display area ram data display area vsync back porch period front porch period display period (nl4-0) hsync dotclk enable vld pd17-0 vsync : frame synchronized signal hsync : line synchronized signal dotclk : dot clock enable : data enable signal vld : valid data signal pd17-0 : rgb(6:6:6) display data back porch period(bpp) : 14h 3 bp3-0 3 2h front porch period(fpp) : 14h 3 fp3-0 3 2h fpp+bpp=16h display period(dp) : nl4-0 176h a number of line of 1-frame : fpp+dp+bpp figure 54 . rgb interface
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 86 vld and enable signals the relationship between vld and enable signals is shown below. when enable is active, the address is not updates. when vld is active and enable is active, the address is updated. table 29 . relationship between vld and enable epl enable vld ram write ram address 0 0 0 valid updated 0 0 1 invalid updated 0 1 * invalid hold 1 0 * invalid hold 1 1 0 valid update 1 1 1 invalid updated
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 87 rgb interface timing time chart for rgb interface is shown below. vsync hsync dotclk enable pd17-0 1- frame back porch period front porch period 3 1 h hlw 3 1clk 1 clk dtst 3 hlw vsync hsync dotclk enable vld pd17-0 valid data 1 h vld figure 55 . 16-/18-bit rgb interface timing vlw: the period in which vsync is ? low ? level hlw: the period in which hsync is ? low ? level dtst: set up time of data transfer note : data for display should be written in the high-speed write mode (hwm= ? 1 ? ) in vsync is in use.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 88 3 1 h hlw 3 3clk 1 clk dtst 3 hlw vsync hsync dotclk enable vld pd17-0 valid data 1 h r g b r g b r g b r g b r g b vsync hsync dotclk enable pd17-0 1- frame back porch period front porch period vld figure 56 . 6-bit rgb interface timing vlw: the period in which vsync is ? low ? level hlw: the period in which hsync is ? low ? level dtst: set up time of data transfer notes : 1. three clocks are regarded as one clock for transfer when data is transferred in 6-bit interface. 2. vsync, hsync, enable, dotclk, vld, and pd17-2 should be transferred in units of three clocks. 3. data for display should be written in the high-speed wri te mode (hwm= ? 1 ? ) in vsync interface is in use.
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 89 moving picture display the S6D0114 incorporates rgb interface to display motion pictures and ram to store data for display. for displaying motion pictures, the S6D0114 has the following features. - motion picture area can only be transferred by the window address function. - the high-speed write mode achieves both low power consumption and high-speed access. - motion picture area to be rewritten can only be transferred. - reducing the amount of data transferred enables reduce the power consumption to the whole system. - still picture area, such as an icon, can be updated while displaying motion pictures combining with the system interface. ram access via rgb interface and system interface ram can be accessed via the system interface when rgb interface is in use. when data is written to ram during rgb interface mode, the enable bit should be low to stop data writing via rgb interface, because ram writing is always performed in synchronization with the dotclk input when enable is high. after this ram access via the system interface, a waiting time is needed for a write/read bus cycle before the next ram access starts via rgb interface. when a ram write conflict occurs, data writing is not guaranteed. example of display motion picture via rgb-i/f and updating still picture via the system interface are shown below. vsync enable dotclk pd17-0 system interface rm=0 index r22 address set index r22 writing display data except moving picture display area rm=1 address set index r22 moving picture display area 2002/01/14 00:00 still picture display area writing moving picture display area writing moving picture display area index set writing picture writing picture writing still picture display area figure 57 . example of updating still picture area during displaying motion picture
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 90 6-bit rgb interface 6-bit rgb interface can be used by setting rim1-0 pins to ? 00 ? . display operation is synchronized with vsync, hsync, and dotclk signals. data for display is transferred to the internal ram via 6-bit rgb data bus (pd17 to 12), the data valid signal (vld), and the data enable signal (enable). unused pins must be fixed to the vdd3 or gnd level. lcdc S6D0114 vsync hsync dotclk vld enable pd17-12 6 12 figure 58 . 6-bit rgb interface r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 1- pixel pd 17 pd 16 pd 15 pd 14 pd 13 pd 12 pd 17 pd 16 pd 15 pd 14 pd 13 pd 12 pd 17 pd 16 pd 15 pd 14 pd 13 pd 12 1 st transfer 2 nd transfer 3 rd transfer *262,144- color display is available in the 6-bit rgb interface input gram write data figure 59 . gram write data format for 6-bit rgb interface mode note: transfer synchronization function for an 6-bit bus interface. the S6D0114 has the transfer counter to count 1st, 2nd and 3rd data transfer in the 6-bit bus interface. the transfer counter is reset on the falling edge of vsync and enters the 1st data transmission state. transfer mismatch can be corrected transfer restarts correctly. in this method, when data is consecutively transferred such as displaying motion pictures, the effect of transfer mismatch will be reduced and recover normal operation. note: the internal display is operated in units of three dotclk. when the dotclk is not input in units of pixels, click mismatch occurs and the frame, which is operated, and the next frame are not display correctly.
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 91 transfer sync. 2 nd transfer 2 nd transfer 1 st transfer 3 rd transfer 1 st transfer 2 nd transfer 3 rd transfer vsync enable dotclk pd17 - 0 transfer sync. 2 nd transfer 2 nd transfer 1 st transfer 3 rd transfer 1 st transfer 2 nd transfer 3 rd transfer vsync enable dotclk pd17 - 0 figure 60 . transfer synchronization function when 6-bit rgb interface 16-bit rgb interface 16-bit rgb interface can be used by setting rim1-0 pins to 01. display operation is synchronized with vsync, hsync, and dotclk signals. data for display is transferred to the internal ram via 6-bit rgb data bus (pd17-13 and 11-1), the data valid signal (vld). instruction should be set via the system interface. lcdc S6D0114 vsync hsync dotclk vld enable pd17-13, 11-1 16 2 figure 61 . 16-bit rgb interface to system r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 input gram write data pd 17 pd 16 pd 15 pd 14 pd 13 pd 11 pd 10 pd 9 pd 8 pd 7 pd 6 pd 5 pd 4 pd 3 pd 2 pd 1 1 - pixel r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 input gram write data pd 17 pd 16 pd 15 pd 14 pd 13 pd 11 pd 10 pd 9 pd 8 pd 7 pd 6 pd 5 pd 4 pd 3 pd 2 pd 1 1 - pixel figure 62 . gram write data in the 16-bit rgb interface mode
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 92 18-bit rgb interface 18-bit rgb interface can be used by setting mif1-0 pins to 01. display operation is synchronized with vsync, hsync, and dotclk signals. data for display is transferred to the internal ram via 6-bit rgb data bus (pd17-0), the data valid signal (vld). lcdc S6D0114 vsync hsync dotclk vld enable pd17-13, 11-1 18 figure 63 . 18-bit rgb interface to system input pd 17 pd 16 pd 15 pd 14 pd 13 pd 12 pd 11 pd 10 pd 9 pd 8 pd 7 pd 6 pd 5 pd 4 pd 3 pd 2 pd 1 pd 0 r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 gram write data *262,144- color display is available in the 18-bit rgb interface 1- pixel figure 64 . gram write data format for 18-bit rgb interface mode usage on external display interface 1. when external display interface is in use, the following functions are not available. table 30 . external display interface and internal display operation function external display interface internal display operation partial display cannot be used can be used scroll function cannot be used can be used interlaced driving cannot be used can be used graphics operation function cannot be used can be used 2. vsync, hsync, and dotclk signals should be supplied during display operation via rgb interface. 3. please make sure that when setting bits of no1-0, sdt1-0, and eq1-0 in rgb interface, the clock on which operations are based changes from the internal operating clock to dclk. 4. rgb data are transferred for three clock cycles in 6-bit rgb interface. data transferred, therefore, should be transferred in units of rgb.
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 93 5. interface signals, vsync, hsync, dotcl, enable, vld, and pd17-0 should be set in units of rgb (pixels) to match rgb transfer. 6. transitions between internal operation mode and external display interface should follow the mode transition sequence shown below. 7. during the period between the completion of displaying one frame data and the next vsync signal, the display will remain front porch period. 8. rgb interface should be used in high-speed write mode (hwm= ? 1 ? ). 9. an address set is done on the falling edge of vsync every frame in rgb interface. hwm=1, am=0 address setting rgb interface mode setting (dm1-0=01, rm=1) index register setting(r22h) wait more than 1 frame rgb interface ram data writing vsync interface operation internal clock operation display operation in synchronization with the internal clock the value set in dm1- 0 and rm will be valid after completion of 1- frame display. display operation in synchronization with rgb signal note: when the interface mode is switched, vsync, hsync, dotclk and enable should be input before setting dm1-0 and rm bit. internal clock operation =>rgb interface(1) wait more than 1 frame internal clock mode setting (dm1-0=00, rm=0) internal clock operation rgb interface operation display operation in synchronization with the rgb signal the value set in dm1- 0 and rm will be valid after completion of 1- frame display. display operation in synchronization with the internal clock note: when switching to rgb interface, please input rgb interface signal(vsync, hsync, dotclk, enable) before dm1-0, rm bit setting. rgb interface (1) => internal clock operation figure 65 . transition between the internal operating clock mode and rgb interface mode
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 94 high-speed burst ram write function the S6D0114 has a high-speed burst ram-write function that can be used to write data to ram in one-fourth the access time required for an equivalent standard ram-write operation. this function is especially suitable for applications that require the high-speed rewriting of the display data, for example, display of color animations, etc. when the high-speed ram-write mode (hwm) is selected, data for writing to ram is once stored to the S6D0114 internal register. when data is selected four times per word, all data is written to the on-chip ram. while this is taking place, the next data can be written to an internal register so that high-speed and consecutive ram writing can be executed for animated displays, etc. microcomputer register 1 register 2 register 3 register 4 18 72 ? 0000 ? h ? 0001 ? h ? 0002 ? h ? 0003 ? h gram address counter (ac) 16 a) high-speed burst ram write operation flow csb (input) b) example of the operation of high-speed consecutive writing to ram 1 2 3 4 1 2 3 4 1 2 3 4 index (r22) ram data 1 ram data 2 ram data 3 ram data 4 ram data 5 ram data 6 ram data 7 ram data 8 ram data 9 ram data 10 ram data 11 ram data 12 index ram write execution time ram write execution time ram write execution time* ram data 1 to 4 ram data 5 to 8 ram data 9 to 12 e (input) db17-0 (input/output) ram write data (72 bit) ram address (ac 15-0) ? 0000 ? h ? 0004 ? h ? 0008 ? h ? 000 a ? h note: the lower two bits of the address must be set in the following way in high-speed write mode. id0=0: the lower 2 bits of the address must be set to 11. id0=1: the lower 2 bits of the address must be set to 00. when a high speed ram write is canceled, the next instruction must only be executed after the ram write execution time has elapsed. figure 66 . example of the operation of high-speed consecutive writing to ram
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 95 csb (input) c) example of the operation of high-speed consecutive writing to ram (when 8-bit interface is used) 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 e (input) index (r22) ram data 1 upper ram data 1 lower ram data 2 upper ram data 2 lower ram data 3 upper ram data 3 lower ram data 4 upper ram data 4 lower ram data 1 upper ram data 1 lower ram data 2 upper ram data 2 lower db15-0 (input/output) ram data 3 upper ram data 3 lower ram data 4 upper ram data 4 lower ram write execution time ram write execution time ram write data (64 bits) ram data 1 to 4 ram data 5 to 8 ram address (ac 15-0) ? 0000 ? h ? 0004 ? h note: the lower two bits of the address must be set in the following way in high-speed write mode. id0=0: the lower 2 bits of the address must be set to 11. id0=1: the lower 2 bits of the address must be set to 00. writing is executed every 4 words in the high speed ram write mode. therefore, mm writing is executed every 8 writing operations when 8-bit interface is used. figure 67 . example of the operation of high-speed consecutive writing to ram (8-bit interface)
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 96 when high-speed write mode is used, note the following. 1. the logical and compare operations cannot be used. 2. data is written to ram each four words. when an address is set, the lower two bits in the address must be set to the following values. *when id0=0, the lower two bits in the address must be set to 11 and be written to ram. *when id0=1, the lower two bits in the address must be set to 00 and be written to ram. 3. data is written to ram each four words. if less than four words of data is written to ram, the last data will not be written to ram. 4. when the index register and ram data write (r22h) have been selected, the data is always written first. ram cannot be written to and read from at the same time. hwm must be set to 0 while ram is being read. 5. high-speed and normal ram write operations cannot be executed at the same time. the mode must be switched and the address must then be set. 6. when high-speed ram write is used with a window address-range specified, dummy write operation may be required to suit the window address range-specification. refer to the high-speed ram write in the window address section. table 31 . comparison between normal and high-speed ram write operations normal ram write (hwm=0) high-speed ram write (hwm=1) logical operation function can be used cannot be used compare operation function can be used cannot be used bgr function (rgb swap) can be used can be used write mask function can be used can be used ram address set can be specified by word id0 bit=0: set the lower two bits to 11 id0 bit=1: set the lower two bits to 00 ram read can be read by word cannot be used ram write can be written by word dummy write operations may have to be inserted according to a window address-range specification window address can be set by word the horizontal range( has/ hse): more than four words the number of horizontal writing: 4n(n 2) external display interface can be used can be used am setting am=1/0 am=0 note: 1 word = 2 byte.
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 97 high-speed ram write in the window address when a window address range is specified, gram data that is in an optional window area can be updated quickly and continuously by use of dummy write operation . so that the number of ram access become 4n as shown in the table below. dummy write operation must be inserted a t the first or last of a row of data, depending on the horizontal window- address range specification bits (hsa1 to 0, hea1 to 0). numbers of dummy write operations of a row must be 4n. table 32 . number of dummy write operations in high-speed ram write ( hs a bits) hsa1 hsa0 number of dummy write operations to be inserted at the start of a row 0 0 0 0 1 1 1 0 2 1 1 3 table 33 . table 34 . number of dummy write operations in high-speed ram write ( he a bits) hea1 hea0 number of dummy write operations to be inserted at the end of a row 0 0 3 0 1 2 1 0 1 1 1 0 note : each row of access must consist of 4 x n operations, including the dummy writes. horizontal access count = first dummy write count + write data count + last dummy write count = 4 x n
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 98 an example of high-speed ram write with a window address-range specified is shown below. the window address-range can be accessed consecutively and quickly by inserting two dummy writes at the start of a row and three dummy writes at the end of a row, as determined by using the window address-range specification bits (hsa1 to 0 =10, hea1 to 0 =00). writing in the horizontal direction am=0, id0=1 window address-range setting hsa=h12, hea=h30 vsa=h08, vea=ha0 high-speed ram write mode setting hwm=1 address set ad=h0810* dummy ram write x 2 ram write x 31 dummy ram write x 3 x 153 h0000 haf83 window address range specification ( rewritable area) h0812 ha030 window address-range setting hsa=h12, hea=h30 vsa=h08, vea=ha0 note: the address set for the high-speed ram write must be 00 or 11 according to the value of the id0 bit. only pre-specified window address-range will be overwritten. gram address map figure 68 . example of high-speed ram write with a window address-range specification
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 99 window address function when data is written to the on-chip gram, a window address-range which is specified by the horizontal address register (start: hsa7-0, end: hea 7-0) and vertical address register (start: vsa7-0, end: vea7-0) can be updated consecutively . data is written to addresses in the direction specified by the am and id1-0 bit. when image data, etc. is being written, data can be written consecutively without thinking a data wrap by doing this. the window must be specified to be within the gram address area described as following example. addresses must be set within the window address. [restriction on window address-range settings] (horizontal direction) 00h hsa7-0 hea7-0 83 h (vertical direction) 00h vsa7-0 vea7-0 af h [restriction on address settings during the window address] (ram address) hsa7-0 ad7-0 hea7-0 vsa7-0 ad15-8 vea7-0 note: in high-speed ram-write mode, the lower two bits of the address must be set as shown below according to the value of the id0 bit. id 0 =0: the lower two bits of the address must be set to 11. id 0 =1: the lower two bits of the address must be set to 00. gram address map ? 0000 ? h ? 0083 ? h ? af00 ? h ? af83 ? h ? 2010 ? h ? 2110 ? h ? 5f10 ? h ? 202 f ? h ? 212f ? h ? 5f2f ? h window address-range specification area hsa7-0 = ? 10 ? h, hse7-0 = ? 2f ? h i/d = 1 (increment) vsa7-0 = ? 20 ? h, vea7-0 = ? 5f ? h am = 0 (horizontal writing) figure 69 . example of address operation in the window address specification
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 100 graphics operation function the S6D0114 can greatly reduce the load of the microcomputer graphics software processing through the 16-bit bus architecture and internal graphics-bit operation function. this function supports the following: 1. a write data mask function that selectively rewrites some of the bits in the 1 8 -bit write data. 2. a logical operation write function that writes the data sent from the microcomputer and the original ram data by a logical operation. 3. a conditional write function that compares the original ram data or write data and the compare-bit data and writes the data sent from the microcomputer only when the conditions match. even if the display size is large, the display data in the graphics ram (gram) can be quickly rewritten. the graphics bit operation can be controlled by combining the entry mode register, the bit set value of the ram- write-data mask register, and the read/write from the microcomputer. table 35 . graphics operation bit setting operation mode i/d am lg2-0 operation and usage write mode 1 0/1 0 000 horizontal data replacement write mode 2 0/1 1 000 vertical data replacement write mode 3 0/1 0 110 111 conditional horizontal data replacement write mode 4 0/1 1 110 111 conditional vertical data replacement microcomputer write-data latch logical/compare operation (lg2- 0): 000:replacement,001:or,010:and,011:eor, 110:replacement with matched write, 111:replacement with unmatched write logical operation bit (lg2=0) compare bit (cp17-0) write-mask register (wm17-0) write bit mask graphic ram (gram) address counter (ac) +1/-1 +256 16 16 18 18 18 18 3 figure 70 . data processing flow of graphic operation
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 101 write-data mask function the S6D0114 has a bit-wise write-data mask function that controls writing the two-byte data from the microcomputer to the gram. bits that are 0 in the write-data mask register (wm1 7 ? 0) cause the corresponding db bit to be written to the gram. bits that are 1 prevent writing to the corresponding gram bit to the gram; the data in the gram is maint ained. this function can be used when only one-pixel data is rewritten or the particular display color is selectively rewritten. gram data r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 data written by the microcomputer write data mask * * * * * * g5 g4 g3 g2 g1 g0 * * * * b1 b0 1 r5 db17 db0 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 0 0 0 17 figure 71 . example of write-data mask function operation note : data is expanded to 18 bits when 16-/8-bit system and 16-bit rgb interface is in use.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 102 graphics operation processing 1. write mode 1: am = 0, lg2 ? 0 = 000 this mode is used when the data is horizontally written at high speed. it can also be used to initialize the graphics ram (gram) or to draw borders. the write-data mask function (wm1 7 ? 0) is also enabled in these operations. after writing, the address counter (ac) automatically increments by 1 (i/d = 1) or decrements by 1 (i/d = 0), and automatically jumps to the counter edge one-raster-row below after it has reached the left or right edge of the gram. wm17 wm0 db17 db0 operation examples: 1) i/d = ? 1 ? , am = ? 0 ? , lg2-0 = ? 000 ? 2) wm17-0 = ? 007ff ? h 3) ac = ? 0000 ? h write data mask: write data (1): write data (2): ? 0000 ? h ? 0001 ? h ? 0002 ? h write data (1) write data (2) gram note: the bits in the gram, * ? s, are not changed 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 1 1 1 1 1 1 1 0 0 1 0 1 0 0 0 1 1 0 0 0 1 0 0 0 0 0 1 1 0 0 0 0 0 1 0 0 1 1 1 * * * * * * * * * * * * 1 1 0 0 0 1 * * * * * * * * * * * * note: when 8/16-bit system interface or 16-bit rgb interface is used, the data is expanded to internal 18-bit. note: frame write mask figure 72 . writing operation of write mode 1
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 103 2. write mode 2: am = 1, lg2-0 = 000 this mode is used when the data is vertically written at high speed. it can also be used to initialize the gram, develop the font pattern in the vertical direction, or draw borders. the write-data mask function (wm1 7 ? 0) is also enabled in these operations. after writing, the address counter (ac) automatically increments by 256, and automatically jumps to the upper-right edge (i/d = 1) or upper-left edge (i/d = 0) following the i/d bit after it has reached the lower edge of the gram. operation examples: 1) i/d = ? 1 ? , am = ? 1 ? , lg2-0 = ? 000 ? 2) wm17-0 = ? 007ff ? h 3) ac = ? 0000 ? h write data mask: write data (1): write data (2): ? 0000 ? h ? 0100 ? h ? 0200 ? h write data (1) write data (2) gram write data (3) write data (3): note: 1. the bits in the gram, * ? s, are not changed. 2. after writing to address ? af00 ? h, the ac jumps to ? 0001 ? h wm17 wm0 db17 db0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 1 1 1 1 1 1 1 0 0 1 0 1 0 0 0 1 1 0 0 0 1 0 0 0 0 0 1 1 0 0 0 0 0 0 1 1 1 1 0 1 0 0 0 1 0 0 0 0 0 1 1 1 0 0 1 1 1 * * * * * * * * * * * * 1 1 0 0 0 1 * * * * * * * * * * * * 0 1 1 1 1 0 * * * * * * * * * * * * note: when 8/16-bit system interface or 16- bit rgb interface is used, the data is expanded to internal 18-bit. figure 73 . writing operation of write mode 2
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 104 3. write mode 3: am = 0, lg2-0 = 110/111 this mode is used when the data is horizontally written by comparing the write data and the set value of the compare register (cp15 ? 0). when the result of the comparison in a byte unit satisfies the condition, the write data sent from the microcomputer is written to the gram. in this operation, the write-data mask function (wm15 ? 0) is also enabled. after writing, the address counter (ac) automatically increments by 1 (i/d = 1) or decrements by 1 (i/d = 0), and automatically jumps to the counter edge one-raster-row below after it has reached the left or right edge of the gram. operation examples: 1) i/d = ? 1 ? , am = ? 0 ? , lg2-0 = ? 110 ? 2) cp15-0 = ? 02860 ? h 3) wm15-0 = ? 00000 ? h 4) ac = ? 0000 ? h write data mask: wm17 wm0 compare register: cp17 cp0 write data (1): write data (2): db17 db0 db17 db0 ( matched) ( unmatched) c r c r compare operation compare operation conditional replacement conditional replacement replacement ? 0000 ? h ? 0001 ? h gram matched replacement of write data (1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 * * * * * * * * * * * * * * * * * * 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 * * * * * * * * * * * * * * * * * * 0 0 1 0 1 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0 1 1 0 0 0 0 0 0 figure 74 . writing operation write mode 3
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 105 4. write mode 4: am =1, lg2-0 = 110/111 this mode is used when a vertical comparison is performed between the write data and the set value of the compare register (cp15 ? 0) to write the data. when the result by the comparison in a byte unit satisfies the condition, the write data sent from the microcomputer is written to the gram. in this operation, the write-data mask function (wm15 ? 0) are also enabled. after writing, the address counter (ac) automatically increments by 256, and automatically jumps to the upper-right edge (i/d = 1) or upper-left edge (i/d = 0 ) after it has reached the lower edge of the gram. 0 0 1 0 1 0 0 0 0 0 1 1 0 0 0 0 0 0 operation examples: 1) i/d = ? 1 ? , am = ? 1 ? , lg2-0 = ? 111 ? 2) cp17-0 = ? 02860 ? h 3) wm17-0 = ? 00000 ? h 4) ac = ? 0000 ? h write data mask: wm17 wm0 compare register: cp17 cp0 write data (1): write data (2): db17 db0 db17 db0 ( unmatched) ( matched) c r c r compare operation compare operation conditional replacement conditional replacement replacement ? 0000 ? h ? 0100 ? h ? af00 ? h write data (1) write data (2) gram note: 1. the bits in the gram, * ? s, are not changed. 2. after writing to address ? af00 ? h, the ac jumps to ? 0001 ? h ? 0000 ? h ? 0001 ? h 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0 1 1 0 0 0 0 0 0 1 0 0 1 1 1 0 0 1 1 0 0 1 1 1 1 1 1 1 0 0 1 1 1 0 0 1 1 0 0 1 1 1 1 1 1 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * 1 0 0 1 1 1 0 0 1 1 0 0 1 1 1 1 1 1 figure 75 . writing operation of write mode 4
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 106 gate driver scan mode setting gate scan mode of S6D0114 is set by sm and gs bit. gs bit determines the scan direction whether the gate driver scans forward or reverse direction. sm bit determines the method of display division ( even/odd or upper/lower division drive). using this function, various connections between S6D0114 and the liquid crystal panels can be accomplished figure 76 . scan mode setting sm gs scan mode 0 0 g1 g175 g2 g176 odd even tft panel g1 g175 g176 g2 s6d0110 g1 g2 g3 g4 g173 g174 g175 g176 0 1 s6d0110 g1 g175 g176 g2 g1 g175 g2 g176 odd even tft panel g174 g175 g176 g173 g4 g1 g2 g3 1 0 g1 g175 g2 g176 tft panel g1 g175 g176 g2 s6d0110 g1 g3 g5 g173 g175 g2 g4 g6 g174 g176 1 1 g1 g175 g2 g176 tft panel g1 g175 g176 g2 s6d0110 g176 g174 g172 g4 g2 g175 g173 g171 g3 g1
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 107 gamma adjustment function the S6D0114 provides the gamma adjustment function to display 262,144 colors simultaneous ly. the gamma adjustment executed by the gradient adjustment register and the micro-adjustment register that determines 8 grayscale levels. furthermore, since the gradient adjustment register and the micro-adjustment register have the positive polarities and negative polarities, adjust them to match lcd panel respectively. g05 g04 g03 g02 g01 g00 graphics ram (gram) msb lsb 64- grayscale control 64- grayscale control 64- grayscale control lcd driver lcd driver lcd driver r g b lcd grayscale amplifier 64 v0 v63 pkp02 pkp01 pkp00 pkp12 pkp11 pkp10 pkp22 pkp21 pkp20 pkp32 pkp31 pkp30 pkp42 pkp41 pkp40 pkp52 pkp51 pkp50 prp02 prp01 prp00 prp12 prp11 prp10 pkn02 pkn01 pkn00 pkn12 pkn11 pkn10 pkn22 pkn21 pkn20 pkn32 pkn31 pkn30 pkn42 pkn41 pkn40 pkn52 pkn51 pkn50 prn02 prn01 prn00 prn12 prn11 prn10 positive polarity register negative polarity register 8 6 6 6 v1 r05 r04 r03 r02 r01 r00 b05 b04 b03 b02 b01 b00 figure 77 . grayscale control
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 108 structure of grayscale amplifier the structure of the grayscale amplifier is shown as below. determine 8 - level (vin0-vin7) by the gradient adjuster and the micro adjustment register. e ach level is split by the internal ladder resistance and l evel between v0 to v 63 is generate d. gradient adjustment register micro adjustment register (6 x 3 bits) prp/n0 prp/n1 pkp/n0 pkp/n1 pkp/n2 pkp/n3 pkp/n4 pkp/n5 oscillation adjustment register vrp/vrn 8 to 1 selector vdh 8 to 1 selector 8 to 1 selector 8 to 1 selector 8 to 1 selector vgs ladder resistance grayscale amplifier 8 to 1 selector 3 3 3 3 3 3 3 3 5 vinp0/vinn0 vinp1/vinn1 vinp2/vinn2 vinp3/vinn3 vinp4/vinn4 vinp5/vinn5 vinp6/vinn6 vinp7/vinn7 v0 v1 v2 v3 v8 v9 v20 v21 v43 v44 v55 v56 v57 v62 v63 figure 78 . structure of grayscale amplifier
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 109 8 to1 sel 8 to1 sel 8 to1 sel 8 to1 sel 8 to1 sel 8 to1 sel kvp1 kvp2 kvp3 kvp4 kvp5 kvp6 kvp7 kvp8 kvp9 kvp10 kvp11 kvp12 kvp13 kvp14 kvp15 kvp16 kvp17 kvp18 kvp19 kvp20 kvp21 kvp22 kvp23 kvp24 kvp25 kvp26 kvp27 kvp28 kvp29 kvp30 kvp31 kvp32 kvp33 kvp34 kvp35 kvp36 kvp37 kvp38 kvp39 kvp40 kvp41 kvp42 kvp43 kvp44 kvp45 kvp46 kvp47 kvp48 v v v v v v vinp0 vinp1 vinp2 vinp3 vinp4 vinp5 vinp6 vinp7 kvp49 kvp0 pkp0[2:0] pkp1[2:0] pkp2[2:0] pkp3[2:0] pkp4[2:0] pkp5[2:0] prp0[2:0] prp1[2:0] vrp[2:0] 5 r 4 r 1 r 1 r 1 r 1 r 4 r 5 r 8 r vrp 0 to 31r vrlp 0 to 28r 5 r 16 r 5 r vrhp 0 to 28r rp0 rp1 rp2 rp3 rp4 rp5 rp6 rp7 rp8 rp9 rp10 rp11 rp12 rp13 rp14 rp15 rp16 rp17 rp18 rp19 rp20 rp21 rp22 rp23 rp24 rp25 rp26 rp27 rp28 rp29 rp30 rp31 rp32 rp33 rp34 rp35 rp36 rp37 rp38 rp39 rp40 rp41 rp42 rp43 rp44 rp45 rp46 rp47 8 to1 sel 8 to1 sel 8 to1 sel 8 to1 sel 8 to1 sel 8 to1 sel kvn1 kvn2 kvn3 kvn4 kvn5 kvn6 kvn7 kvn8 kvn9 kvn10 kvn11 kvn12 kvn13 kvn14 kvn15 kvn16 kvn17 kvn18 kvn19 kvn20 kvn21 kvn22 kvn23 kvn24 kvn25 kvn26 kvn27 kvn28 kvn29 kvn30 kvn31 kvn32 kvn33 kvn34 kvn35 kvn36 kvn37 kvn38 kvn39 kvn40 kvn41 kvn42 kvn43 kvn44 kvn45 kvn46 kvn47 kvn48 v v v v v v vinn0 vinn1 vinn2 vinn3 vinn4 vinn5 vinn6 vinn7 kvn49 kvn0 pkn0[2:0] pkn1[2:0] pkn2[2:0] pkn3[2:0] pkn4[2:0] pkn5[2:0] prn0[2:0] prn1[2:0] vrn[2:0] 5 r 4 r 1 r 1 r 1 r 1 r 4 r 5 r 8 r vrn 0 to 31r vrln 0 to 28r 5 r 16 r 5 r vrhn 0 to 28r rn0 rn1 rn2 rn3 rn4 rn5 rn6 rn7 rn8 rn9 rn10 rn11 rn12 rn13 rn14 rn15 rn16 rn17 rn18 rn19 rn20 rn21 rn22 rn23 rn24 rn25 rn26 rn27 rn28 rn29 rn30 rn31 rn32 rn33 rn34 rn35 rn36 rn37 rn38 rn39 rn40 rn41 rn42 rn43 rn44 rn45 rn46 rn47 exvr ( ) vdh figure 79 . structure of ladder / 8 to 1 selector
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 110 gamma adjustment register this block ha s the register to set up the grayscale voltage adjusting to the gamma specification of the lcd panel. th ese register s can independent ly set up to positive/negative polarities and there are 3 types of register groups to adjust gradient and oscillation on number of the grayscale, characteristics of the grayscale voltage. (average < r >< g >< b > are common.) the f ollowing fi g ure indicates the operation of each adjusting register. grayscale number grayscale voltage a) gradient adjustment grayscale number grayscale voltage grayscale number grayscale voltage b) oscillation adjustment c) micro-adjustment figure 80 . the operation of adjusting register a) gradient adjustment resistor the gradient adjust ment resistors are used to adjust the gradient in the middle of the grayscale characteristics for the voltage without changing the dynamic range. to accomplish the adjustment, it controls the variable resistor (vrhp (n) / vrl (n)) of the ladder resistor for the grayscale voltage generator. also, there is an independent resistor on the positive/negative polarities in order for corresponding to asymmetry drive. b) oscillation adjustment resistor the oscillation-adjusting resistor is to adjust oscillation of the grayscale voltage. to accomplish the adjustment, it controls the variable resistor (vrp (n)) of the ladder resistor for the grayscale voltage generator located at lower side of the ladder resistor. (adjust upper side by input gvdd level.) also, there is an independent resistor on the positive/negative polarities as well as the gradient adjusting resistor. c) micro adjustment resistor the micro adjust ment resistor is to make subtle adjustment of the grayscale voltage level. to accomplish the adjustment, it controls the each reference voltage level by the 8 to 1 selector towards the 8-leveled reference voltage generated from the ladder resistor. also, there is an independent resistor on the positive/negative polarities as well as other adjusting resistors.
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 111 table 36 . gamma correction registers register positive polarity negative polarity set-up contents prp0[2:0] prn0[2:0] variable resistor vrhp(n) gradient adjustment prp1[2:0] prn1[2:0] variable resistor vrlp(n) oscillation adjustment vrp[4:0] vrn[4:0] variable resistor vrp(n) pkp0[2:0] pkn0[2:0] the voltage of grayscale number 1 is selected by the 8 to 1 selector pkp1[2:0] pkn1[2:0] the voltage of grayscale number 8 is selected by the 8 to 1 selector pkp3[2:0] pkn3[2:0] the voltage of grayscale number 20 is selected by the 8 to 1 selector pkp4[2:0] pkn4[2:0] the voltage of grayscale number 43 is selected by the 8 to 1 selector pkp5[2:0] pkn5[2:0] the voltage of grayscale number 55 is selected by the 8 to 1 selector micro-adjustment pkp6[2:0] pkn6[2:0] the voltage of grayscale number 62 is selected by the 8 to 1 selector
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 112 ladder resistor/8 to 1 selector this block outputs the reference voltage of the grayscale voltage. there are two ladder resistors including the variable resistor and the 8 to 1 selector selecting voltage generated by the ladder resistance voltage. the variable and 8 to 1 resistors are controlled by the gamma resistor. also, there are pins that connect to the external volume resistor. and it allows to compensate the dispersion of length between one panel to another. variable resistor there are 2 types of the variable resistors that is for the gradient adjustment (vrhp (n) / vrlp (n)) and for the oscillation adjustment (vrp (n)). the resistance value is set by the gradient adjusting resistor and the oscillation adjusti ment resistor as below. table 37 . gradient adjustment register value prp(n) [2:0 ] resistance value prp(n) 000 0r 001 4r 010 8r 011 12r 100 16r 101 20r 110 24r 111 28r table 38 . oscillation adjustment register value vrp(n) [2:0 ] resistance value vrp(n) 00000 0r 00001 1r 00010 2r . . . . . . 11101 29r 11110 30r 11111 31r
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 113 the 8 to 1 selector in the 8 to 1 selector, the voltage level must be selected given by the ladder resistance and the micro-adjusting register. and output the voltage the six types of the reference voltage, the vin1- to vin6. following figure explains the relationship between the micro-adjusting register and the selecting voltage. table 39 . relationship between micro-adjustment register and selected voltage selected voltage register value pkp(n) [2 : 0] vinp(n)1 vinp(n)2 vinp(n)3 vinp(n)4 vinp(n)5 vinp(n)6 000 kvp(n)1 kvp(n)9 kvp(n)17 kvp(n)25 kvp(n)33 kvp(n)41 001 kvp(n)2 kvp(n)10 kvp(n)18 kvp(n)26 kvp(n)34 kvp(n)42 010 kvp(n)3 kvp(n)11 kvp(n)19 kvp(n)27 kvp(n)35 kvp(n)43 011 kvp(n)4 kvp(n)12 kvp(n)20 kvp(n)28 kvp(n)36 kvp(n)44 100 kvp(n)5 kvp(n)13 kvp(n)21 kvp(n)29 kvp(n)37 kvp(n)45 101 kvp(n)6 kvp(n)14 kvp(n)22 kvp(n)30 kvp(n)38 kvp(n)46 110 kvp(n)7 kvp(n)15 kvp(n)23 kvp(n)31 kvp(n)39 kvp(n)47 111 kvp(n)8 kvp(n)16 kvp(n)24 kvp(n)32 kvp(n)40 kvp(n)48
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 114 table 40 . gamma adjusting voltage formula (positive polarity) 1 pins formula micro-adjusting register value reference voltage kvp0 gvdd - vinp0 kvp1 gvdd- d v *5r/sumrp pkp02-00 = ? 000 ? kvp2 gvdd- d v *9r/sumrp pkp02-00 = ? 001 ? kvp3 gvdd- d v *13r/sumrp pkp02-00 = ? 010 ? kvp4 gvdd- d v *17r/sumrp pkp02-00 = ? 011 ? kvp5 gvdd- d v *21r/sumrp pkp02-00 = ? 100 ? kvp6 gvdd- d v *25r/sumrp pkp02-00 = ? 101 ? kvp7 gvdd- d v *29r/sumrp pkp02-00 = ? 110 ? kvp8 gvdd- d v *33r/sumrp pkp02-00 = ? 111 ? vinp1 kvp9 gvdd- d v * ( 33r +vrhp) /sumrp pkp12-10 = ? 000 ? kvp10 gvdd- d v * ( 34r +vrhp) /sumrp pkp12-10 = ? 001 ? kvp11 gvdd- d v * ( 35r +vrhp) /sumrp pkp12-10 = ? 010 ? kvp12 gvdd- d v * ( 36r +vrhp) /sumrp pkp12-10 = ? 011 ? kvp13 gvdd- d v * ( 37r +vrhp) /sumrp pkp12-10 = ? 100 ? kvp14 gvdd- d v * ( 38r +vrhp) /sumrp pkp12-10 = ? 101 ? kvp15 gvdd- d v * ( 39r +vrhp) /sumrp pkp12-10 = ? 110 ? kvp16 gvdd- d v * ( 40r +vrhp) /sumrp pkp12-10 = ? 111 ? vinp2 kvp17 gvdd- d v * ( 45r +vrhp) /sumrp pkp22-20 = ? 000 ? kvp18 gvdd- d v * ( 46r +vrhp) /sumrp pkp22-20 = ? 001 ? kvp19 gvdd- d v * ( 47r +vrhp) /sumrp pkp22-20 = ? 010 ? kvp20 gvdd- d v * ( 48r +vrhp) /sumrp pkp22-20 = ? 011 ? kvp21 gvdd- d v * ( 49r +vrhp) /sumrp pkp22-20 = ? 100 ? kvp22 gvdd- d v * ( 50r +vrhp) /sumrp pkp22-20 = ? 101 ? kvp23 gvdd- d v * ( 5 1 r +vrhp) /sumrp pkp22-20 = ? 110 ? kvp24 gvdd- d v * ( 5 2 r +vrhp) /sumrp pkp22-20 = ? 111 ? vinp3 kvp25 gvdd- d v * ( 68r +vrhp) /sumrp pkp32-30 = ? 000 ? kvp26 gvdd- d v * ( 69r +vrhp) /sumrp pkp32-30 = ? 001 ? kvp27 gvdd- d v * ( 70r +vrhp) /sumrp pkp32-30 = ? 010 ? kvp28 gvdd- d v * ( 71r +vrhp) /sumrp pkp32-30 = ? 011 ? kvp29 gvdd- d v * ( 72r +vrhp) /sumrp pkp32-30 = ? 100 ? kvp30 gvdd- d v * ( 73r +vrhp) /sumrp pkp32-30 = ? 101 ? kvp31 gvdd- d v * ( 74r +vrhp) /sumrp pkp32-30 = ? 110 ? kvp32 gvdd- d v * ( 75r +vrhp) /sumrp pkp32-30 = ? 111 ? vinp4 kvp33 gvdd- d v * ( 80r +vrhp) /sumrp pkp42-40 = ? 000 ? kvp34 gvdd- d v * ( 81r +vrhp) /sumrp pkp42-40 = ? 001 ? kvp35 gvdd- d v * ( 82r +vrhp) /sumrp pkp42-40 = ? 010 ? kvp36 gvdd- d v * ( 83r +vrhp) /sumrp pkp42-40 = ? 011 ? kvp37 gvdd- d v * ( 84r +vrhp) /sumrp pkp42-40 = ? 100 ? kvp38 gvdd- d v * ( 85r +vrhp) /sumrp pkp42-40 = ? 101 ? kvp39 gvdd- d v * ( 86r +vrhp) /sumrp pkp42-40 = ? 110 ? kvp40 gvdd- d v * ( 87r +vrhp) /sumrp pkp42-40 = ? 111 ? vinp5 kvp41 gvdd- d v * ( 87r +vrhp+vrlp) /sumrp pkp52-50 = ? 000 ? kvp42 gvdd- d v * ( 91r +vrhp+vrlp) /sumrp pkp52-50 = ? 001 ? kvp43 gvdd- d v * ( 95r +vrhp+vrlp) /sumrp pkp52-50 = ? 010 ? kvp44 gvdd- d v * ( 99r +vrhp+vrlp) /sumrp pkp52-50 = ? 011 ? kvp45 gvdd- d v * ( 103r +vrhp+vrlp) /sumrp pkp52-50 = ? 100 ? kvp46 gvdd- d v * ( 107r +vrhp+vrlp) /sumrp pkp52-50 = ? 101 ? kvp47 gvdd- d v * ( 111r +vrhp+vrlp) /sumrp pkp52-50 = ? 110 ? kvp48 gvdd- d v * ( 115r +vrhp+vrlp) /sumrp pkp52-50 = ? 111 ? vinp6 kvp49 gvdd- d v * ( 120r +vrhp+vrlp) /sumrp - vinp7 sumrp: total of the positive polarity ladder resistance = 128r + vrhp + vrlp + vrp sumrp: total of the negative polarity ladder resistance = 128r + vrhn + vrln + vrn d v: potential difference between kv0 and kv49 = gvdd*sumrp*sumrn / [sumrp*sumrn+exvr*(sumrp+sumrn)]
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 115 table 41 . gamma voltage formula (positive polarity) 2 grayscale voltage formula grayscale voltage formula v0 vinp0 v32 v43+(v20-v43)*(11/23) v1 vinp1 v33 v43+(v20-v43)*(10/23) v2 v3+(v1-v3)*(8/24) v34 v43+(v20-v43)*(9/23) v3 v8+(v1-v8)*(450/800) v35 v43+(v20-v43)*(8/23) v4 v8+(v3-v8)*(16/24) v36 v43+(v20-v43)*(7/23) v5 v8+(v3-v8)*(12/24) v37 v43+(v20-v43)*(6/23) v6 v8+(v3-v8)*(8/24) v38 v43+(v20-v43)*(5/23) v7 v8+(v3-v8)*(4/24) v39 v43+(v20-v43)*(4/23) v8 vinp2 v40 v43+(v20-v43)*(3/23) v9 v20+(v8-v20)*(22/24) v41 v43+(v20-v43)*(2/23) v10 v20+(v8-v20)*(20/24) v42 v43+(v20-v43)*(1/23) v11 v20+(v8-v20)*(18/24) v43 vinp4 v12 v20+(v8-v20)*(16/24) v44 v55+(v43-v55)*(22/24) v13 v20+(v8-v20)*(14/24) v45 v55+(v43-v55)*(20/24) v14 v20+(v8-v20)*(12/24) v46 v55+(v43-v55)*(18/24) v15 v20+(v8-v20)*(10/24) v47 v55+(v43-v55)*(16/24) v16 v20+(v8-v20)*(8/24) v48 v55+(v43-v55)*(14/24) v17 v20+(v8-v20)*(6/24) v49 v55+(v43-v55)*(12/24) v18 v20+(v8-v20)*(4/24) v50 v55+(v43-v55)*(10/24) v19 v20+(v8-v20)*(2/24) v51 v55+(v43-v55)*(8/24) v20 vinp3 v52 v55+(v43-v55)*(6/24) v21 v43+(v20-v43)*(22/23) v53 v55+(v43-v55)*(4/24) v22 v43+(v20-v43)*(21/23) v54 v55+(v43-v55)*(2/24) v23 v43+(v20-v43)*(20/23) v55 vinp5 v24 v43+(v20-v43)*(19/23) v56 v60+(v55-v60)*(20/24) v25 v43+(v20-v43)*(18/23) v57 v60+(v55-v60)*(16/24) v26 v43+(v20-v43)*(17/23) v58 v60+(v55-v60)*(12/24) v27 v43+(v20-v43)*(16/23) v59 v60+(v55-v60)*(8/24) v28 v43+(v20-v43)*(15/23) v60 v62+(v55-v62)*(350/800) v29 v43+(v20-v43)*(14/23) v61 v62+(v60-v62)*(16/24) v30 v43+(v20-v43)*(13/23) v62 vinp6 v31 v43+(v20-v43)*(12/23) v63 vinp7
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 116 table 42 . gamma adjusting voltage formula (negative polarity) 1 pins formula micro-adjusting register value reference voltage kvn0 gvdd - vinn0 kvn1 gvdd- d v *5r/sumrn pkn02-00 = ? 000 ? kvn2 gvdd- d v *9r/sumrn pkn02-00 = ? 001 ? kvn3 gvdd- d v *13r/sumrn pkn02-00 = ? 010 ? kvn4 gvdd- d v *17r/sumrn pkn02-00 = ? 011 ? kvn5 gvdd- d v *21r/sumrn pkn02-00 = ? 100 ? kvn6 gvdd- d v *25r/sumrn pkn02-00 = ? 101 ? kvn7 gvdd- d v *29r/sumrn pkn02-00 = ? 110 ? kvn8 gvdd- d v *33r/sumrn pkn02-00 = ? 111 ? vinn1 kvn9 gvdd- d v * ( 33r +vrhn) /sumrn pkn12-10 = ? 000 ? kvn10 gvdd- d v * ( 34r +vrhn) /sumrn pkn12-10 = ? 001 ? kvn11 gvdd- d v * ( 35r +vrhn) /sumrn pkn12-10 = ? 010 ? kvn12 gvdd- d v * ( 36r +vrhn) /sumrn pkn12-10 = ? 011 ? kvn13 gvdd- d v * ( 37r +vrhn) /sumrn pkn12-10 = ? 100 ? kvn14 gvdd- d v * ( 38r +vrhn) /sumrn pkn12-10 = ? 101 ? kvn15 gvdd- d v * ( 39r +vrhn) /sumrn pkn12-10 = ? 110 ? kvn16 gvdd- d v * ( 40r +vrhn) /sumrn pkn12-10 = ? 111 ? vinn2 kvn17 gvdd- d v * ( 45r +vrhn) /sumrn pkn22-20 = ? 000 ? kvn18 gvdd- d v * ( 46r +vrhn) /sumrn pkn22-20 = ? 001 ? kvn19 gvdd- d v * ( 47r +vrhn) /sumrn pkn22-20 = ? 010 ? kvn20 gvdd- d v * ( 48r +vrhn) /sumrn pkn22-20 = ? 011 ? kvn21 gvdd- d v * ( 49r +vrhn) /sumrn pkn22-20 = ? 100 ? kvn22 gvdd- d v * ( 50r +vrhn) /sumrn pkn22-20 = ? 101 ? kvn23 gvdd- d v * ( 5 1 r +vrhn) /sumrn pkn22-20 = ? 110 ? kvn24 gvdd- d v * ( 5 2 r +vrhn) /sumrn pkn22-20 = ? 111 ? vinn3 kvn25 gvdd- d v * ( 68r +vrhn) /sumrn pkn32-30 = ? 000 ? kvn26 gvdd- d v * ( 69r +vrhn) /sumrn pkn32-30 = ? 001 ? kvn27 gvdd- d v * ( 70r +vrhn) /sumrn pkn32-30 = ? 010 ? kvn28 gvdd- d v * ( 71r +vrhn) /sumrn pkn32-30 = ? 011 ? kvn29 gvdd- d v * ( 72r +vrhn) /sumrn pkn32-30 = ? 100 ? kvn30 gvdd- d v * ( 73r +vrhn) /sumrn pkn32-30 = ? 101 ? kvn31 gvdd- d v * ( 74r +vrhn) /sumrn pkn32-30 = ? 110 ? kvn32 gvdd- d v * ( 75r +vrhn) /sumrn pkn32-30 = ? 111 ? vinn4 kvn33 gvdd- d v * ( 80r +vrhn) /sumrn pkn42-40 = ? 000 ? kvn34 gvdd- d v * ( 81r +vrhn) /sumrn pkn42-40 = ? 001 ? kvn35 gvdd- d v * ( 82r +vrhn) /sumrn pkn42-40 = ? 010 ? kvn36 gvdd- d v * ( 83r +vrhn) /sumrn pkn42-40 = ? 011 ? kvn37 gvdd- d v * ( 84r +vrhn) /sumrn pkn42-40 = ? 100 ? kvn38 gvdd- d v * ( 85r +vrhn) /sumrn pkn42-40 = ? 101 ? kvn39 gvdd- d v * ( 86r +vrhn) /sumrn pkn42-40 = ? 110 ? kvn40 gvdd- d v * ( 87r +vrhn) /sumrn pkn42-40 = ? 111 ? vinn5 kvn41 gvdd- d v * ( 87r +vrhn+vrln) /sumrn pkn52-50 = ? 000 ? kvn42 gvdd- d v * ( 91r +vrhn+vrln) /sumrn pkn52-50 = ? 001 ? kvn43 gvdd- d v * ( 95r +vrhn+vrln) /sumrn pkn52-50 = ? 010 ? kvn44 gvdd- d v * ( 99r +vrhn+vrln) /sumrn pkn52-50 = ? 011 ? kvn45 gvdd- d v * ( 103r +vrhn+vrln) /sumrn pkn52-50 = ? 100 ? kvn46 gvdd- d v * ( 107r +vrhn+vrln) /sumrn pkn52-50 = ? 101 ? kvn47 gvdd- d v * ( 111r +vrhn+vrln) /sumrn pkn52-50 = ? 110 ? kvn48 gvdd- d v * ( 115r +vrhn+vrln) /sumrn pkn52-50 = ? 111 ? vinn6 kvn49 gvdd- d v * ( 120r +vrhn+vrln) /sumrn - vinn7 sumrp: total of the positive polarity ladder resistance = 128r + vrhp + vrlp + vrp sumrn: total of the negative polarity ladder resistance = 128r + vrhn + vrln + vrn d v: potential difference between kv0 and kv49 = gvdd*sumrp*sumrn / [sumrp*sumrn+exvr*(sumrp+sumrn)]
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 117 table 43 . gamma voltage formula (negative polarity) 2 grayscale voltage formula grayscale voltage formula v0 vinn0 v32 v43+(v20-v43)*(11/23) v1 vinn1 v33 v43+(v20-v43)*(10/23) v2 v3+(v1-v3)*(8/24) v34 v43+(v20-v43)*(9/23) v3 v8+(v1-v8)*(450/800) v35 v43+(v20-v43)*(8/23) v4 v8+(v3-v8)*(16/24) v36 v43+(v20-v43)*(7/23) v5 v8+(v3-v8)*(12/24) v37 v43+(v20-v43)*(6/23) v6 v8+(v3-v8)*(8/24) v38 v43+(v20-v43)*(5/23) v7 v8+(v3-v8)*(4/24) v39 v43+(v20-v43)*(4/23) v8 vinn2 v40 v43+(v20-v43)*(3/23) v9 v20+(v8-v20)*(22/24) v41 v43+(v20-v43)*(2/23) v10 v20+(v8-v20)*(20/24) v42 v43+(v20-v43)*(1/23) v11 v20+(v8-v20)*(18/24) v43 vinn4 v12 v20+(v8-v20)*(16/24) v44 v55+(v43-v55)*(22/24) v13 v20+(v8-v20)*(14/24) v45 v55+(v43-v55)*(20/24) v14 v20+(v8-v20)*(12/24) v46 v55+(v43-v55)*(18/24) v15 v20+(v8-v20)*(10/24) v47 v55+(v43-v55)*(16/24) v16 v20+(v8-v20)*(8/24) v48 v55+(v43-v55)*(14/24) v17 v20+(v8-v20)*(6/24) v49 v55+(v43-v55)*(12/24) v18 v20+(v8-v20)*(4/24) v50 v55+(v43-v55)*(10/24) v19 v20+(v8-v20)*(2/24) v51 v55+(v43-v55)*(8/24) v20 vinn3 v52 v55+(v43-v55)*(6/24) v21 v43+(v20-v43)*(22/23) v53 v55+(v43-v55)*(4/24) v22 v43+(v20-v43)*(21/23) v54 v55+(v43-v55)*(2/24) v23 v43+(v20-v43)*(20/23) v55 vinn5 v24 v43+(v20-v43)*(19/23) v56 v60+(v55-v60)*(20/24) v25 v43+(v20-v43)*(18/23) v57 v60+(v55-v60)*(16/24) v26 v43+(v20-v43)*(17/23) v58 v60+(v55-v60)*(12/24) v27 v43+(v20-v43)*(16/23) v59 v60+(v55-v60)*(8/24) v28 v43+(v20-v43)*(15/23) v60 v62+(v55-v62)*(350/800) v29 v43+(v20-v43)*(14/23) v61 v62+(v60-v62)*(16/24) v30 v43+(v20-v43)*(13/23) v62 vinn6 v31 v43+(v20-v43)*(12/23) v63 vinn7
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 118 000000 111111 v63 v0 output level negative polarity positive polarity ram data (common charactersics to rgb) figure 81 . relationship between ram data and output voltage positive polarity negative polarity sn vcom figure 82 . relationship between source output and vcom
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 119 the 8-color display mode the S6D0114 incorporates 8-color display mode. the grayscale levels to be used is v0 and v63 and all the other levels ( v1~v62) are halt. so that it attempts to lower power consumption. d uring the 8-color mode, the gamma micro adjustment register, pkp00-pkp52 and pkn00-pkn52 are invalid. since v1-v62 is stopped, the r g b data in the gram should be set to 000000 or 111111 before set the mode. the level power supply (v1-v62) is in off condition during the 8-color mode in order to select v0/v63. g05 g04 g03 g02 g01 g00 graphics ram (gram) msb lsb r g b lcd binary amplifier 2 vdh vgs pkp02 pkp01 pkp00 pkp12 pkp11 pkp10 pkp22 pkp21 pkp20 pkp32 pkp31 pkp30 pkp42 pkp41 pkp40 pkp52 pkp51 pkp50 prp02 prp01 prp00 prp12 prp11 prp10 pkn02 pkn01 pkn00 pkn12 pkn11 pkn10 pkn22 pkn21 pkn20 pkn32 pkn31 pkn30 pkn42 pkn41 pkn40 pkn52 pkn51 pkn50 prn02 prn01 prn00 prn12 prn11 prn10 positive polarity register negative polarity register 8 6 6 6 r05 r04 r03 r02 r01 r00 b05 b04 b03 b02 b01 b00 on/off control on/off control on/off control lcd driver lcd driver lcd driver figure 83 . 8-color display control
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 120 off gon= ? 1 ? dte= ? 1 ? d1-0= ? 10 ? wait (2 frame or higher) on gon= ? 1 ? dte= ? 0 ? d1-0= ? 10 ? off gon= ? 0 ? dte= ? 0 ? d1-0= ? 00 ? wait (2 frame or higher) ram setup cl= ? 1 ? wait (40ms or higher) on gon= ? 0 ? dte= ? 0 ? d1-0= ? 01 ? wait (2 frame or higher) on gon= ? 1 ? dte= ? 0 ? d1-0= ? 01 ? on gon= ? 1 ? dte= ? 0 ? d1-0= ? 11 ? on gon= ? 1 ? dte= ? 1 ? d1-0= ? 11 ? display by 8-color mode off gon= ? 1 ? dte= ? 1 ? d1-0= ? 10 ? wait (2 frame or higher) on gon= ? 1 ? dte= ? 0 ? d1-0= ? 10 ? off gon= ? 0 ? dte= ? 0 ? d1-0= ? 00 ? wait (2 frame or higher) ram setup cl= ? 0 ? wait (40ms or higher) on gon= ? 0 ? dte= ? 0 ? d1-0= ? 01 ? wait (2 frame or higher) on gon= ? 1 ? dte= ? 0 ? d1-0= ? 01 ? on gon= ? 1 ? dte= ? 0 ? d1-0= ? 11 ? on gon= ? 1 ? dte= ? 1 ? d1-0= ? 11 ? display by 262,144-color mode wait (2 frame or higher) wait (2 frame or higher) 262,144- color => 8-color 8- color => 262,144 -color figure 84 . set up procedure for the 8-color mode
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 121 system structure example following diagram indicates the system structure, which composes the 132 (width) x 176 (length) dots tft-lcd panel. t.b.d figure 85 . system structure
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 122 instruction set up flow display off gon= 1 dte= 1 d1-0= 10 wait (more than 2 frames) display off gon= 1 dte= 0 d1-0= 10 wait (more than 2 frames) display off gon= 0 dte= 0 d1-0= 00 display off power off sap2-0= 000 ap2-0= 000 continue to the display on flow power setting display on gon= 0 dte= 0 d1-0= 01 wait (more than 2 frames) display on gon= 1 dte= 0 d1-0= 01 display on gon= 1 dte= 0 d1-0= 11 display on gon= 1 dte= 1 d1-0= 11 display on continue to the display on flow < display off> < display on> eq=0 wait (more than 2 frames) figure 86 . instruction set up flow
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 123 < standby> < sleep> display off flow standby set (stb= 1 ) oscillation start wait 10ms standby cancel (stb= 0 ) power setting display on flow display off flow sleep set (slp= 1 ) sleep cancel (slp= 0 ) power setting display on flow standby set standby cancel sleep set sleep cancel figure 87 . instruction setup flow (continued)
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 124 oscillation circuit the S6D0114 can oscillate between the osc1 and osc2 pins using an internal r-c oscillator with an external oscillation resistor. note that in r-c oscillation, the oscillation frequency is changed according to the external resistance value, wiring length, or operating power-supply voltage. if rf is increased or power supply voltage is decrease, the oscillation frequency decreases. for the relationship between rf resistor value and oscillation frequency, see the electric characteristics notes section. osc1 osc2 S6D0114 clock (200 khz) damping resistance (2 k w ) 1) external clock mode 2) external resistance oscillation mode osc1 osc2 S6D0114 rf note: the rf resistance must be located near the osc1/osc2 pin on the chip figure 88 . oscillation circuit
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 125 n-raster-row reversed ac drive the S6D0114 supports not only the lcd reversed ac drive in a one-frame unit but also the n-raster-row reversed ac drive which alternates in an n-raster-row unit from one to 64 raster-rows. when a problem affecting display quality occurs, the n-raster-row reversed ac drive can improve the quality. determine the number of the raster-rows n (nw bit set value +1) for alternating after confirmation of the display quality with the actual lcd panel. however, if the number of ac raster-row is reduced, the lcd alternating frequency becomes high. because of this, the charge or discharge current is increased in the lcd cells. 1 2 3 4 175 176 184 1 2 3 4 175 176 184 1 2 1 frame 1 frame blank period blank period frame a/c waveform drive 176 raster-row n-raster-row a/c waveform drive 176 raster-row reverse 3 raster-row eor= ? 1 ? figure 89 . example of an ac signal under n-raster-row reversed ac drive
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 126 interlace drive S6D0114 supports the interlace drive to protect from the flicker. it splits one frame into n fields and drives. determine the n fields (fld bit stetting value) after confirming on the actual lcd display. following table indicates n fields: the gate selecting position when it is 1 or 3. a nd the diagram below indicates the output waveform when the field interlace drive is active. gs= ? 0 ? fld1-0 setting value 01 11 field gate - (1) (2) (3) g1 o o g2 o o g3 o o g4 o o g5 o o g6 o o g7 o o g8 o o g9 o o ? ? g173 o o g174 o o g175 o o g176 o o gs= ? 1 ? fld1-0 setting value 01 11 field gate - (1) (2) (3) g176 o o g175 o o g174 o o g173 o o g172 o o g171 o o g170 o o g169 o o g168 o o ? ? g4 o o g3 o o g2 o o g1 o o 1 frame blank period field (1) field (2) field (3) field (1) ac polarity g1 g2 g3 g4 g5 g6 g3n+1 g3n+2 g3n+3 figure 90 . interlace drive and output waveform
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 127 a/c timing following diagram indicates the a/c timing on the each a/c drive method. after every 1 drawing, the a/c timing is occurred on the reversed frame ac drive. after the a/c timing, the blank (all gate output : vgoff level ) period described below is inserted. w hen it is on the interlace drive , blank period is inserted every a/c timing. when the reversed n-raster-row is driving, a blank period is inserted after all screens are drawn. front and back porch can be adjusted using fp3-0 and bp3-0 bits (r08h). in interlace drive mode, blank period can be adjusted using blp13-0 and blp23-0 bit (r09h). blank period = back porch + blank period 1 + blank period 2 + front porch frame 1 frame reverse ac drive 1 frame period field 1 a/c a/c a/c blank period = back porch + front porch 3 field interlace drive n-raster-row reversed ac drive front porch back porch a/c timing 1 frame period front porch field 2 field 3 blank period 2 (blp2) blank period 1 (blp1) back porch a/c 1 frame period front porch back porch a/c a/c a/c a/c a/c a/c a/c a/c a/c a/c n-raster-row blank period = back porch + front porch n-raster-row n-raster-row n-raster-row n-raster-row n-raster-row n-raster-row n-raster-row n-raster-row n-raster-row figure 91 . a/c timing
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 128 frame frequency adjusting function the S6D0114 has an on-chip frame-frequency adjustment function. the frame frequency can be adjusted by the instruction setting (div, rtn) during the lcd driver as the oscillation frequency is always same. if the oscillation frequency is set to high, animation or a static image can be displayed in suitable ways by changing the frame frequency. when a static image is displayed, the frame frequency can be set low and the low-power consumption mode can be entered. when high-speed screen switching for an animated display, etc. is required, the frame frequency can be set high. relationship between lcd drive duty and frame frequency the relationships between the lcd drive duty and the frame frequency is calculated by the following expression. the frame frequency can be adjusted in the 1h period adjusting bit (rtn) and in the operation clock division bit (div) by the instruction. frame frequency = f osc clock cycles per raster-row x division ratio x (line+b) [ hz] f osc : r-c oscillation frequency line: number of raster-rows (nl bit) clock cycles per raster-row: rtn bit division ratio: div bit b: blank period(back porch + front porch) figure 92 . formula for the frame frequency example calculation driver raster-row : 176 1h period: 16 clock (rtn3 to 0 = 0000) operation clock division ratio: 1division b: blank period (bp + fp): 8 fosc = 60hz x (0+16) clock x 1 division x (176+ b ) lines = 177 [khz] in this case, the r c oscillation frequency becomes 177 khz. the external resistance value of the rc oscillator must be adjusted to be 177 khz. note: when fld1-0= ? 11 ? (interlace drive), b = bp + fp + blp1 + blp2
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 129 screen-division driving function the S6D0114 can select and drive two screens at any position with the screen-driving position registers (r14 and r15). any two screens required for display are selectively driven and reducing lcd-driving voltage and power consumption. for the 1 st division screen, start line (ss17 to 10) and end line (se17 to 10) are specified by the 1 st screen-driving position register (r14). for the 2 nd division screen, start line (ss27 to 20) and end line (se27 to 20) are specified by the 2 nd screen-driving position register (r15). the 2 nd screen control is effective when the spt bit is 1. the total count of selection-driving lines for the 1 st and 2 nd screens must correspond to the lcd-driving duty set value. rm * oct 14th 10:18am g1 g7 g26 g42 1 st screen: 7-raster-row driving non-display area 2nd screen: 17 raster-row driving non-display area driving raster-row: nl4-0 = 10101 (176 lines) 1st screen setting: ss17-10 = 00h, se17-10 = 06h 2nd screen setting: ss27-20 = 19h, se27-20 = 29h, spt = 1 figure 93 . driving on 2 screen
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 130 restriction on the 1 st /2 nd screen driving position register settings the following restrictions must be satisfied when setting the start line (ss17 to 10) and end line (se17 to 10) of the 1 st screen driving position register (r4 2h ) and the start line (ss27 to 20) and end line (se27 to 20) of the 2 nd screen driving position register (r 43h ) for the S6D0114. note that incorrect display may occur if the restrictions are not satisfied. table 44 . restrictions on the 1 st /2 nd screen driving position register setting 1 st screen driving (spt=0) register setting display operation (se17 to 10) ? (ss17 to 10) = nl full screen display normally displays (se17 to 10) to (ss17 to 10) (se17 to 10) ? (ss17 to 10) < nl partial display normally displays (se17 to 10) to (ss17 to 10) white display for all other times (ram data is not related at all) (se17 to 10) ? (ss17 to 10) > nl setting disabled note 1: ss17 to 10 se17 to 10 afh note 2: setting se27 to 20 and ss27 to 20 are invalid 2 nd screen driving (spt=1) register setting display operation ((se17 to 10) ? (ss17 to 10)) + ((se27 to 20) ? (ss27-20)) = nl full screen display normally displays (se27 to 10) to (ss17 to 10) ((se17 to 10) ? (ss17 to 10)) + ((se27 to 20) ? (ss27-20)) < nl partial display normally displays (se27 to 10) to (ss17 to 10) white display for all other times (ram data is not related at all) ((se17 to 10) ? (ss17 to 10)) + ((se27 to 20) ? (ss27-20)) > nl setting disabled note 1: ss17 to 10 se17 to 10 < ss27 to 20 se27 to 20 afh note 2: (se27 to 20) ? (ss17 to 10) nl the driver output can ? t be set for non-display area during the partial display. determine based on specification of the panels. source output in non-display area pt1 pt0 positive polarity negative polarity gate output in non-display area 0 0 v63 v0 normal drive 0 1 v63 v0 vgoff 1 0 vss vss vgoff 1 1 hi-z hi-z vgoff
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 131 refer to the following flow to set up the partial display. full screen display pt1-0 = 00 set ss/se bits wait (more than 2 frames) pt1-0 = 01 or pt1-0 = 10 or pt1-0 = 11 partial display on set ss/se bits full screen display set as need setting flow for full screen driver split screen drive set up flow figure 94 . partial display set up flow
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 132 application circuit the following figure indicates a schematic diagram of application circuit for S6D0114. t.b.d figure 95 . application circuit
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 133 specifications absolute maximum ratings table 45 . absolute maximum rating (vss = 0v) item symbol rating unit supply voltage vdd - 0.3 ~ + 5.0 v supply voltage for step-up circuit vci - 0.3 ~ + 5.0 v lcd supply voltage range |vgh ? vgl| 30 v input v oltage range v in - 0.3 to vdd +0. 5 v operating temperature t opr -40 ~ +85 c storage temperature t stg -55 ~ +110 c notes: 1. absolute maximum rating is the limit value beyond which the ic may be broken. they do not assure operations. 2. operat ing temperature is the range of device-operating temperature. they do not guarantee chip performance. 3. absolute maximum rating is guaranteed when our company ? s package used.
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 134 dc characteristics table 46 . dc characteristics ((vdd = 1.8v or vdd3 = 3.3v), gvdd = 4.5v, avdd = 5.0v, vss = 0v) characteristic symbol condition min typ max unit note operating voltage(1) vdd 1.8 - 2.5 v *1 operating voltage(2) vdd 3 2.3 - 3.3 v *1 driver positive power supply vgh +7 - 20.0 v driver negative power supply vgl -7 - -15.0 v gate off power supply vgoff -5 - -15 v *2 high v ih 0.7xvdd - vdd v *2 logic input voltage low v il 0 - 0.3xvdd v *3 high v oh i oh = -2.0ma vdd-0.5 vdd v *3 logic output voltage low v ol i ol = 2.0ma 0.0 - 0.5 v input leakage current i il vin = vss or vdd -1.0 - 1.0 m a *2 output leakage current i ol vin = vss or vdd -3.0 - 3.0 m a *3 operating frequency fosc - khz *5 1 st step-up input voltage vci1 - 2.5 - 3.3 v 1 st step-up output efficiency avdd % 2 nd step-up input voltage vci2 4.5 5.5 v 2 nd step-up output efficiency vgh % 3 rd step-up input voltage vci3 20 v 3 rd step-up output efficiency vgl 94 99 % 4 th step-up input voltage vci4 2.5 3.3 v 4 th step-up output efficiency vcl % - - tbd m a *6
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 135 table 47 . dc characteristics for lcd driver outputs ((vdd = 1.8v or vdd3 = 3.3v), gvdd = 4.5v, avdd = 5.0v, vss = 0v) characteristic symbol condition min typ max unit note high-level output current (gradation output) ioh1 vx = 4.5v, vout = 3.5v - - -0.05 ma *4 low-level output current (gradation output) iol1 vx = 0.1v, vout = 1.1v 0.05 - - ma *4 4.2v v x - 20 30 mv 0.8v < v x < 4.2v - 10 20 mv output voltage deviation (mean value) d vo v x 0.8v - 20 30 mv output voltage range v o - gvdd+0. 1 - gvdd- 0.1 v high-level output current (binary output) i oh2 v x = 5v, v out = 4v, - - -0.1 ma low-level output current (binary output) i ol2 v x = 0.0v, v out = 1.0v 0.1 - - ma gate driver on resistance r ong ta = 25 c vgh ? vgl = 26v i load = +/- 100 ua - - 1.0 k *4 notes : 1. vss = 0v. 2. csb, rs, db0 to db17, e, rw, resetb. 3. db0 to db17, cl. 4. resistance value when ? 0.1[ma] is applied during the on status of the output pin sn or gn. ron[k ] = ? v [v] / 0.1 [ma] ( ? v : voltage change when ? 0.1[ma] is applied in the on status) 5. fosc = fcl x cl division. f frame = f cl / 2 / display duty ratio. 6. dynamic current condition : vdd=vci=2.7v, vddi=1.8v, x3, 1/5 bias, fosc = 115.2 khz, f frame = 180 hz, v3 ? mv3 = 19.6v, v2 = 7.84v
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 136 ac characteristics parallel write interface (68 mode , hwm =1 ) table 48 . parallel write interface characteristic (68 mode , hwm =1 ) (vdd = 1.8 v to 2.7 v, t a = - 3 0 to +85 o c) characteristic symbol min. typ. max. unit e_rd cycle time t c 62 - - pulse rise / fall time t r ,t f - - 3 e_rd pulse width high t wh 30 - - e_rd pulse width low t wl 30 - - rs and csb setup time t su1 10 - - rs and csb hold time t h1 10 - - db setup time t su2 20 - - db hold time t h2 1 0 - - ns rs,csb rw_wr b e_rd b db 17~0 vld t su1 t h1 t wh t wl t r t su2 t c t h2 t f valid data figure 96 . burst write timing diagram (68-series)
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 137 parallel write interface (68 mode , hwm =0 ) table 49 . parallel write interface characteristic (68 mode , hwm =0 ) (v dd = 1.8 v to 2.7 v, t a = - 30 to +85 o c) characteristic symbol min. typ. max. unit e_rd cycle time t c 250 - - pulse rise / fall time t r ,t f - - 10 e_rd pulse width high t wh 100 - - e_rd pulse width low t wl 100 - - rs and csb setup time t su1 10 - - rs and csb hold time t h1 10 - - db setup time t su2 20 - - db hold time t h2 1 0 - - ns rs,csb rw_wr b e_rd b db 17~0 vld t su1 t h1 t wh t wl t r t su2 t c t h2 t f valid data figure 97 . single write timing diagram (68-series)
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 138 parallel read interface (68 mode) table 50 . parallel read interface characteristic (68 mode) (v dd = 1.8 v to 2.7 v, t a = - 3 0 to +85 o c) characteristic symbol min. typ. max. unit e_rd cycle time t c 450 - - pulse rise / fall time t r ,t f - - 10 e_rd pulse width high t wh 200 - - e_rd pulse width low t wl 200 - - rs and csb setup time t su 10 - - rs and csb hold time t h 10 - - db output delay time t d 20 - - db output hold time t dh 10 - - ns rs,csb rw_wr b e_rd b db 17~0 t su t h t wh t wl t r t c t d t dh valid data t f figure 98 . read timing diagram (68-series)
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 139 parallel write interface (80 mode , hwm =1 ) table 51 . parallel write interface characteristic (80 mode , hwm =1 ) (v dd = 1.7 v to 2.7 v, t a = - 4 0 to +85 o c) characteristic symbol min. typ. max. unit rw_wr cycle time t c 62 - - pulse rise / fall time t r ,t f - - 3 rw_wr pulse width high t wh 30 - - rw_wr pulse width low t wl 30 - - rs and csb setup time t su1 10 - - rs and csb hold time t h1 10 - - db setup time t su2 20 - - db hold time t h2 10 - - ns rs,csb rw_wr b e_rd b db 17~0 vld t su1 t h1 t wl t wh t f t su2 t c t h2 t r valid data figure 99 . burst write timing diagram (80-series)
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 140 parallel write interface (80 mode , hwm =0 ) table 52 . parallel write interface characteristic (80 mode , hwm =0 ) (v dd = 1.7 v to 2.7 v, t a = - 4 0 to +85 o c) characteristic symbol min. typ. max. unit rw_wr cycle time t c 250 - - pulse rise / fall time t r ,t f - - 10 rw_wr pulse width high t wh 100 - - rw_wr pulse width low t wl 100 - - rs and csb setup time t su1 10 - - rs and csb hold time t h1 10 - - db setup time t su2 20 - - db hold time t h2 10 - - ns rs,csb rw_wr b e_rd b db17~0 vld t su1 t h1 t wl t wh t f t su2 t c t h2 t r valid data figure 100 . single write timing diagram (80-series)
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 141 parallel read interface (80 mode) table 53 . parallel read interface characteristic (80 mode) (v dd = 1.7 v to 2.7 v, t a = -40 to +85 o c) characteristic symbol min. typ. max. unit e_rd cycle time t c 450 - - pulse rise / fall time t r ,t f - - 10 e_rd pulse width high t wh 200 - - e_rd pulse width low t wl 200 - - rs and csb setup time t su 10 - - rs and csb hold time t h 10 - - db output delay time t d 20 - - db output hold time t dh 10 - - ns rs,csb rw_wr e_rd db17~ 0 t su t h t wl t wh t f t c t d t dh valid data t r figure 101 . read timing diagram (80-series)
132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display S6D0114 preliminary 142 clock synchronized serial write mode table 54 . clock synchronized serial write mode characteristic (v dd = 1.7 v to 2.7 v, t a = - 4 0 to +85 o c) characteristic symbol min. typ. max. unit scl clock cycle time t c 20 - - pulse rise / fall time t r ,t f - - 3 scl clock width (high, low) t w 7 - - csb setup time t su1 10 - - csb hold time t h1 10 - - sdi data setup time t su2 5 - - sdi data hold time t h2 5 - - ns csb scl sdi tsu2 tsu1 th2 t h1 t c t r t w t w t f figure 102 . clock synchronized serial interface mode timing diagram
S6D0114 132-rgb x 176-dot 1-chip driver ic for 262,144-color tft-lcd display preliminary 143 clock synchronized serial read mode table 55 . clock synchronized serial read mode characteristic (v dd = 1.7 v to 2.7 v, t a = - 4 0 to +85 o c) characteristic symbol min. typ. max. unit scl clock cycle time t c 50 - - pulse rise / fall time t r ,t f - - 3 scl clock width (high, low) t w 20 - - csb setup time t su1 20 - - csb hold time t h1 10 - - s d o data delay time t d 10 - - s d o data delay time t dh 10 ns csb scl sdo t d tsu1 t dh t h1 t c t r t w t w t f figure 103 . clock synchronized serial interface mode timing diagram

▲Up To Search▲

Price & Availability of S6D0114

	To Download S6D0114 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .