agilent t-1 3 / 4 (5 mm) alingap lamps data sheet features high intensity general purpose leads popular 5 mm diameter available in bulk, tape and reel, or ammopack ? or 25 viewing angles choice of colors: amber or red applications indoor/outdoor applications small store-front signs message panels road construction barrier lights center high mount stop lights spoiler, car decorative lighting motorcycle/bicycle warning lights hlmp-cx08 series, hlmp-cx25 series hlmp-cx27 series, hlmp-c610 description the hlmp-cx08, hlmp-cx25, hlmp-cx27, and hlmp-c610 series are 5 mm lamps specially designed for applications requir- ing very high on-axis intensity that is not achievable with a standard lamp. these devices are capable of producing light output over a wide range of drive currents. built using alingap technology, they are well suited for typical 5 mm ts-algaas lamp applica- tions, and have significantly superior reliability than most ts-algaas lamps in wet/ hot environments. these lamps come with clear non-diffused lens and are optically designed to yield superior light output. device selection typical viewing luminous intensity, angle [1] (degrees), iv (mcd) @ 20 ma dominant part number standoff 2 q 1 / 2 min. typ. color wavelength [2] hlmp-c008-u00xx no 8 2900.0 6000.0 red 626 hlmp-c208-s00xx 8 2600.0 3000.0 amber 590 hlmp-c608-r00xx 8 1000.0 2000.0 red 635 hlmp-c610-r00xx yes 8 1000.0 2000.0 red 635 hlmp-c025-p00xx no 25 500.0 1000.0 red 626 hlmp-c225-o00xx 25 450.0 800.0 amber 590 hlmp-c625-p00xx 25 500.0 700.0 red 635 hlmp-c027-p00xx yes 25 500.0 1000.0 red 626 hlmp-c627-p00xx 25 500.0 700.0 red 635 notes: 1. q 1 / 2 is the off-axis angle at which the luminous intensity is half of the axial luminous intensity. 2. the dominant wavelength, l d , is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device.
2 package dimensions hlmp-cx27 6.10 (0.240) 5.46 (0.215) 1.27 (0.050) nom. 2.54 (0.100) 0.45 (0.018) sq. nom. cathode lead 25.40 (1.00) min. nom. 5.08 (0.200) 4.57 (0.100) 13.55 (0.533) 13.35 (0.525) 0.89 (0.035) 0.64 (0.023) 9.19 (0.362) 8.43 (0.332) 1.32 (0.052) 1.02 (0.040) 6.10 (0.240) 5.46 (0.215) 1.27 (0.050) nom. 2.54 (0.100) 0.45 (0.018) sq. nom. cathode lead 25.40 (1.00) min. nom. 5.08 (0.200) 4.57 (0.100) 0.89 (0.035) 0.64 (0.023) 9.19 (0.362) 8.43 (0.332) 1.02 (0.004) max. typ. 1.00 (0.040) max. epoxy meniscus 1.00 (0.040) max. epoxy meniscus hlmp-cx25 hlmp-c610 hlmp-cx08 6.10 (0.240) 5.46 (0.215) 1.27 (0.050) nom. 2.54 (0.100) 0.45 (0.018) sq. nom. cathode lead 25.40 (1.000) min. nom. 5.21 (0.205) 4.70 (0.105) 13.50 (0.53) 13.30 (0.52) 1.07 (0.042) 0.56 (0.022) 9.14 (0.360) 8.36 (0.330) 1.32 (0.052) 1.02 (0.040) 6.10 (0.240) 5.46 (0.215) 1.27 (0.050) nom. 2.54 (0.100) 0.45 (0.018) sq. nom. cathode lead 25.40 (1.000) min. nom. 5.21 (0.205) 4.70 (0.105) 1.07 (0.042) 0.56 (0.022) 9.14 (0.360) 8.36 (0.330) 1.02 (0.004) max. typ. 1.00 (0.040) max. epoxy meniscus 1.00 (0.040) max. epoxy meniscus
3 absolute maximum ratings at t a =25 c parameter absolute maximum units peak forward current 70 ma average forward current [1] 30 ma dc current [2] 50 ma reverse voltage (i r = 100 a) 5 v led junction temperature 110 c operating temperature -40 to +100 c storage temperature -40 to +120 wave soldering temperature [1.59 mm (0.063 in.) from body] 250 c for 3 seconds solder dipping temperature [1.59 mm (0.063 in.) from body] 260 c for 5 seconds notes: 1. see figure 2 to establish pulsed operating conditions. 2. derate linearly from 50 c at 0.5 ma/ c. 3. the transient peak current is the maximum non-recurring peak current that can be applied to the device without damaging the led die and wirebond. it is not recommended that this device be operated at peak currents above the absolute maximum peak forward current. part numbering system hlmp - c x xx - x x x xx mechanical option 00: bulk 02: tape & reel, straight leads dd: ammo pack color bin options 0: full color bin distribution maximum iv bin options 0: open (no max. limit) minimum iv bin options please refer to the iv bin table viewing angle & standoff option 08: 8 degrees, without standoff 10: 8 degrees, with standoff 25: 25 degrees, without standoff 27: 25 degrees, with standoff color options 0: alingap red 626 nm 2: alingap amber 590 nm 6: alingap red 635 nm
4 optical/electrical characteristics at t a =25 c test symbol parameter device min. typ. [3] max. units conditions 2 q 1 / 2 included angle between half hlmp-c008 8 deg. i f = 20 ma luminous intensity points [1] hlmp-c208 8 see note 1 hlmp-c608 8 hlmp-c025 25 hlmp-c225 25 hlmp-c625 25 hlmp-c610 8 hlmp-c027 25 hlmp-c627 25 l d dominant wavelength [2] hlmp-c008 626 nm see note 2 hlmp-c208 590 hlmp-c608 635 hlmp-c025 626 hlmp-c225 590 hlmp-c625 635 hlmp-c610 635 hlmp-c027 626 hlmp-c627 635 l peak peak wavelength hlmp-c008 635 nm measurement at peak hlmp-c208 594 hlmp-c608 650 hlmp-c025 635 hlmp-c225 594 hlmp-c625 650 hlmp-c610 650 hlmp-c027 635 hlmp-c627 650 dl 1 / 2 spectral line halfwidth 17 nm t s speed of response 20 ns c capacitance 40 pf v f = 0; f = 1 mhz r q j-pin thermal resistance 260 c/w junction to cathode lead v f forward voltage hlmp-c008 1.9 2.4 v i f = 20 ma hlmp-c208 1.9 2.6 hlmp-c608 1.9 2.2 hlmp-c025 1.9 2.4 hlmp-c225 1.9 2.6 hlmp-c625 1.9 2.2 hlmp-c610 1.9 2.2 hlmp-c027 1.9 2.4 hlmp-c627 1.9 2.2 v r reverse breakdown voltage 5.0 v i r = 100 a notes: 1. q 1 / 2 is the off-axis angle at which the luminous intensity is half of the axial luminous intensity. 2. the dominant wavelength, l d , is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 3. typical specification for reference only. do not exceed absolute maximum ratings.
5 figure 1. relative intensity vs. wavelength. figure 2. maximum tolerable peak current vs. pulse duration. figure 3. forward current vs. forward voltage. figure 4. relative luminous intensity vs. forward current. ratio of maximum tolerable peak current to maximum tolerable dc current 1.0 10,000 6 1 t p ?pulse duration ?? 1000 5 3 100 10 4 2 i peak ?max. i dc ?max. 100 khz 30 khz 10 khz 3 khz 1 khz 300 hz 100 hz current ma 1.0 0 v f forward voltage v 50 40 30 10 2.0 3.0 60 1.5 2.5 20 red amber relative luminous intensity (normalized at 20 ma) 0 0 i f dc forward current ma 2.5 2.0 1.5 0.5 60 3.0 20 40 1.0 wavelength nm relative intensity 550 600 650 700 1.0 0.5 0 c208 c225 c008 c025 c027 c608 c625 c627 c610 figure 5. maximum forward dc current vs. ambient temperature. forward current (ma) 0 0 ambient temperature ( c) 40 120 60 20 40 20 60 80 100 r j-a = 780 c/w
6 soldering/cleaning cleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from the chlorinated hydrocarbon family (methylene chloride, trichloro- ethylene, carbon tetrachloride, etc.) are not recommended for cleaning led parts. all of these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic led parts. for information on soldering leds, please refer to applica- tion note 1027. figure 7. relative luminous intensity vs. angular displacement for hlmp-cx25 and hlmp-cx27. relative intensity 1.0 0 angular displacement degrees 0.8 0.6 0.5 0.7 0.2 -70 -60 0.1 0.3 0.4 -40 0 20 30 50 70 90 0.9 -90 -20 -80 -50 -30 -10 10 40 60 80 figure 6. relative luminous intensity vs. angular displacement for hlmp-cx08 and hlmp-cx10. relative intensity 1.0 0 angular displacement degrees 0.8 0.6 0.5 0.7 0.2 -20 -15 0.1 0.3 0.4 -10 0 5 10152025 0.9 -25 -5
7 intensity bin limits intensity range (mcd) color bin min. max. p 540.0 850.0 q 850.0 1200.0 r 1200.0 1700.0 s 1700.0 2400.0 red t 2400.0 3400.0 u 3400.0 4900.0 v 4900.0 7100.0 w 7100.0 10200.0 x 10200.0 14800.0 y 14800.0 21400.0 z 21400.0 30900.0 o 510.0 800.0 p 800.0 1250.0 q 1250.0 1800.0 yellow r 1800.0 2900.0 s 2900.0 4700.0 t 4700.0 7200.0 u 7200.0 11700.0 v 11700.0 18000.0 w 18000.0 27000.0 maximum tolerance for each bin limit is 18%. mechanical option matrix mechanical option code definition 00 bulk packaging, minimum increment 500 pcs/bag 02 tape & reel, straight leads, minimum increment 1300 pcs/bag dd ammo pack, straight leads with minimum increment 2k/pack note: all categories are established for classification of products. products may not be available in all categories. please contact your local agilent representative for further clarification/information. color categories lambda (nm) color category # min. max. 3 584.5 587.0 2 587.0 589.5 amber 4 589.5 592.0 6 592.0 594.5 7 594.5 597.0 tolerance for each bin limit is 0.5 nm.
www.agilent.com/semiconductors for product information and a complete list of distributors, please go to our web site. for technical assistance call: americas/canada: +1 (800) 235-0312 or (916) 788-6763 europe: +49 (0) 6441 92460 china: 10800 650 0017 hong kong: (+65) 6756 2394 india, australia, new zealand: (+65) 6755 1939 japan: (+81 3) 3335-8152(domestic/interna- tional), or 0120-61-1280(domestic only) korea: (+65) 6755 1989 singapore, malaysia, vietnam, thailand, philippines, indonesia: (+65) 6755 2044 taiwan: (+65) 6755 1843 data subject to change. copyright ? 2003-2005 agilent technologies, inc. obsoletes 5988-9482en june 6, 2005 5989-3262en
|
