icte5.0 thru icte15c series t rans z orb transient voltage suppressor stand-off voltage - 5.0 to 15 volts peak pulse power - 1500 watts features plastic package has underwriters laboratory flammability classification 94v-0 glass passivated junction 1500w peak pulse power capability with a 10/1000 m s waveform, repetition rate (duty cycle): 0.05% excellent clamping capability low incremental surge resistance fast response time: typically less than 1.0ps from 0 volts to v (br) for uni-directional and 5.0ns for bi-directional ideal for data and bus line applications high temperature soldering guaranteed: 265?/10 seconds, 0.375" (9.5mm) lead length, 5lbs. (2.3 kg) tension includes 1n6373 thru 1n6385 mechanical data case: molded plastic over a passivated junction terminals: plated axial leads, solderable per mil-std-750, method 2026 polarity: for uni-directional types the color band denotes the cathode, which is posititive with respect to the anode under normal tvs operation mounting position: any weight: 0.045 ounce, 1.2 grams maximum ratings and characteristics ratings at 25? ambient temperature unless otherwise specified. symbol value units peak pulse power dissipation with a 10/1000 m s waveform (note 1, fig. 1) p ppm minimum 1500 watts steady state power dissipation, t l = 75? at lead lengths 0.375" (9.5mm) p m(av) 6.5 watts peak pulse current with a 10/1000 m s waveform (note 1, fig. 3) i ppm see table 1 & 2 amps peak forward surge current, 8.3ms single half sine-wave superimposed on rated load for uni-directional i fsm 200 amps only (jedec method) (note 2) maximum instantaneous forward voltage at 100a for uni-directional only v f 3.5 volts operating junction and storage temperature range t j , t stg -55 to +175 ? notes: (1) non-repetitive current pulse, per fig. 3 and derated above t a = 25? per fig. 2 (2) 8.3ms single half sine-wave, duty cycle=4 pulses per minute maximum 1/21/99 1.00 (25.4) min. 1.00 (25.4) min. 0.375 (9.527) 0.360 (9.146) 0.205 (5.207) 0.190 (4.826) dia. 0.042 (1.07) 0.038 (0.958) dia. case style 1.5ke dimensions in inches and (millimeters)
electrical characteristics at 25 c (jedec registered data) table 1 minimum (3) maximum maximum maximum maximum stand-off breakdown reverse clamping clamping peak general voltage voltage leakage voltage voltage pulse jedec semiconductor at 1.0ma. at v wm at l pp = 1.0a at l pp = 10a current type part v wm v (br) i d vc vc i pp number number (volts) (volts) ( m a) (volts) (volts) (amps) 1n6373 (2) icte-5 (2) 5.0 6.0 300 7.1 7.5 160 1n6374 icte-8 8.0 9.4 25.0 11.3 11.5 100 1n6375 icte-10 10.0 11.7 2.0 13.7 14.1 90 1n6376 icte-12 12.0 14.1 2.0 16.1 16.5 70 1n6377 icte-15 15.0 17.6 2.0 20.1 20.6 60 electrical characteristics at 25 c (jedec registered data) table 2 minimum (3) maximum maximum maximum maximum stand-off breakdown reverse clamping clamping peak general voltage voltage leakage voltage voltage pulse jedec semiconductor at 1.0ma. at v wm at l pp = 1a at l pp = 10a current type part v wm v (br) i d vc vc i pp number number (volts) (volts) ( m a) (volts) (volts) (amps) 1n6382 icte-8c 8.0 9.4 50.0 11.4 11.6 100 1n6383 icte-10c 10.0 11.7 2.0 14.1 14.5 90 1n6384 icte-12c 12.0 14.1 2.0 16.7 17.1 70 1n6385 icte-15c 15.0 17.6 2.0 20.8 21.4 60 notes: (1) ?c ?suffix indicates bi-directional (2) icte-5 and 1n6373 are not available as bi-directional (3) the minimum breakdown voltage as shown takes into consideration the 1 volt tolerance normally specified for power supply re gulation on most integrated circuit manufacturers data sheets. please consult factory for devices that require reduced clamping voltages where tighter regulated po wer supply voltages are employed. (4) clamping factor: 1.33 at full lo rated power; 1.20 at 50% rated power; clamping factor: the ratio of the actual vc (clamping voltage) to the v (br) (breakdown voltage) as measured on a specific device.
0.1 m s 1.0 m s 10 m s 100 m s 1.0ms 10ms 0.1 1.0 10 100 0 50 100 150 200 0 25 50 75 100 25 75 125 175 2 5 0 1.0 2.0 3.0 4.0 0 100 50 1 100,000 10,000 1,000 100 12 5 10 20 50 100 200 fig. 1 - peak pulse power rating curve p ppm , peak pulse power, kw td, pulse width, sec. t a , ambient temperature, ? v (br) , breakdown voltage, volts fig. 4 - typical junction capacitance uni-directional type fig. 3 - pulse waveform t, time, ms i pp, peak pulse current, %i pp peak pulse power (p pp ) or current (i pp ) derating in percentage, % c j , junction , capacitance, pf non-repetitive pulse waveform shown in fig. 3 t a =25? pulse width (td) is defined as that point where the peak current decays to 50% of i pp tr=10 m sec. measured at zero bias measured at stand-off voltage, v wm td half value - i pp 2 10 x 1000 m s waveform as defined by r.e.a. peak value i pp fig. 2 - pulse derating curve t a =25 c f=1.0 mhz vsig=50mvp-p ratings and characteristic curves icte5.0 thru icte15c series
1 10 100 10 100 200 1 100,000 10,000 1,000 100 10 100 200 1 50 10 6 8 10 12 14 16 18 20 22 24 ratings and characteristic curves icte5.0 thru icte15c series number of cycles at 60 hz vc, clamping voltage, volts fig. 7 - typical characteristic clamping voltage i fsm , peak forward surge current, amperes i pp , peak pulse current, amperes for uni-directional only 8.3ms single half sine-wave (jedec method) t a =25 c unidirectional only icte-5 i cte-8 icte-10 icte-12 icte-15 fig. 6 - maximum non-repetitive peak forward surge current fig. 5 - typical junction capacitance bidirectional type c j , junction capacitance, pf measured at stand-off voltage (v wm ) v (br), breakdown voltage, volts t j =25 c f=1.0 mhz vsig=50mvp-p measured at zero bias
|
