designed & dimensioned in millimeters[inches] this product manufactured with lead-free processing pb do not scale from this print mhxxx-mhxrp-xxxxxx-xxxx overall cable length millimeters of cable 0100 min. (see note 8 & 9) end 1 connector end 2 connector or preparation cable callout -mh1rp: mhf-p-c-ra-cax (see sheet 2) (081 cable type: mhf1-p-c-ra-ca3) (113 cable type: mhf1-p-c-ra-ca4) -mh3rp: mhf-p-c-ra-ca3 (see sheet 2) (081 cable type only) -01bj1: sma-j-c-x-st-bhx (see sheet 2) (081 cable type: sma-j-c-x-st-bh3) (113 cable type: sma-j-c-x-st-bh4) -01bj2: sma-j-c-x-st-brx (see sheet 2) (081 cable type: sma-j-c-x-st-br3) (113 cable type: sma-j-c-x-st-br4) -01sb1: sma-j-c-x-st-sbx (see sheet 2) (081 cable type: sma-j-c-x-st-sb3) (113 cable type: sma-j-c-x-st-sb4) -01sr1: sma-j-c-x-st-srx (see sheet 2) (081 cable type: sma-j-c-x-st-sr3) (113 cable type: sma-j-c-x-st-sr4) -sing: single ended (one end only, see note 11) -xxxxxx: stripped and tinned (this end only- see notes 11-15 & sheet 2, fig. 3) -mh1rp: mhf-p-c-ra-cax (see sheet 2) (081 cable type: mhf1-p-c-ra-ca3) (113 cable type: mhf1-p-c-ra-ca4) -mh3rp: mhf-p-c-ra-ca4 (see sheet 2) (081 cable type only) (see fig. 2) "c" format: x.xmm (see fig. 2) "b" format: x.xmm (see fig. 2) "a" format: x.xmm c 081: cca-081 (0.81 od miniature coax cable) 113: cca-113 (1.13 od miniature coax cable) "a" mm "b" mm "c" mm "d" mm "e" mm fig.2 cable stripping dimensions per configurations (see table 1)(see notes 12,13,14,15) c c c c c c fig. 1 hmxxx-mh1rp-01bj1-xxxx shown do not leave any space blank, each must contain a numeric character 0 thru 9. sheet of unless otherwise specified, dimensions are in millimeters [inches]. tolerances are: decimals angles .x: 0.3 [.01] 2 .xx: 0.13 [.005] .xxx: 0.051 [.0020] material: micro rf cable assembly by: mhxxx-mhxrp-xxxxxx-xxxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing cummings 07/26/2005 2 1 sheet scale: 2:1 see end 1 and end 2 assembly prints f:\dwg\misc\mktg\mhxxx-mhxrp-xxxxxx-xxxx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 notes: 1. represents a critical dimension. 2. cable cut length: = (length: xxxx) - (subtractor for end 1) - (subtractor for end 2). (see table 1 for subtractors) 3. assembly to be 100% tested for opens & shorts. 4. assembly to be 100% hi-pot tested per table 1. 5. after final electrical tests, label each cable assembly with 1 label -et 6. criticals on connector prints to be checked in process. 7. finished assemblies to be packaged per packaging standard co-hd-wi-3033-m. -lockwashers, nuts, and gaskets to be shipped unassembled. 8. cable stocked in inches, 1 inch = 25.4 millimeters. 9. cable lengths longer than 1000 millimeters are not supported by s.i. test data. 10. minimum bend radius for mh081 = 5.0 [.20] mh113 = 6.8 [.27] 11. for sing ended or stripped and tinned assemblies: make a double ended assembly at twice the cable length and test before cutting assembly in half. 12. dim "a", "b", and "c" have a minimum value of 0.0mm & a maximum value of 9.9mm. 13. production of strip and tin for center dielectic use: a. 14. production of strip and tin for shield use: d=a+b. 15. production of strip and tin for jacket use: e=a+b+c. 16. for -ra to -ra, connectors should both be oriented up. (see sheet 2, fig. 4) revision f
-mh1rp (right angle plug) (081 cable type use drawing no. mhf1-p-c-ra-ca3 for assembly instructions) (113 cable type use drawing no. mhf1-p-c-ra-ca4 for assembly instructions) -01bj1 (straight bulkhead jack) (081 cable type use drawing no. sma-j-c-x-st-bh3 for assembly instructions) (113 cable type use drawing no. sma-j-c-x-st-bh4 for assembly instructions) -mh3rp (right angle plug) (081 cable type use drawing no. mhf3-p-c-ra-ca3 for assembly instructions) plating 10" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: mhf1-p-c-ra-ca3) or (end connector p/n: mhf1-p-c-ra-ca4) plating 10" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: mhf3-p-c-ra-ca3) -01bj2 (reversed polarity ) (straight bulkhead jack) (081 cable type use drawing no. sma-j-c-x-st-br3 for assembly instructions) (113 cable type use drawing no. sma-j-c-x-st-br4 for assembly instructions) plating 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-j-c-h-st-br3) or (end connector p/n: sma-j-c-h-st-br4) note: all critical dimensions on mhf1-p-c-ra-cax that apply must be verified. note: all critical dimensions on mhf3-p-c-ra-ca3 that apply must be verified. note: all critical dimensions on sma-j-c-x-st-br3 or sma-j-c-x-br4 that apply must be verified. note: all critical dimensions on sma-j-c-x-st-bh3 or sma-j-c-x-st-bh4 that apply must be verified. plating 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-j-c-h-st-bh3) or (end connector p/n: sma-j-c-h-st-bh4) fig. 4 mh081-mh3rp-mh1rp-xxxx shown (see note 16) fig. 3 mhxxx-mh1rp-102148-xxxx shown plating 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-j-c-h-st-sr3) or (end connector p/n: sma-j-c-h-st-sr4) plating 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-j-c-h-st-sb3) or (end connector p/n: sma-j-c-h-st-sb4) note: all critical dimensions on sma-j-c-x-st-sb3 or sma-j-c-x-st-sb4 that apply must be verified. note: all critical dimensions on sma-j-c-x-st-sr3 or sma-j-c-x-sr4 that apply must be verified. -01sr1 (reversed polarity ) (sealed straight bulkhead jack) (081 cable type use drawing no. sma-j-c-x-st-sr3 for assembly instructions) (113 cable type use drawing no. sma-j-c-x-st-sr4 for assembly instructions) -01sb1 (sealed straight bulkhead jack) (081 cable type use drawing no. sma-j-c-x-st-sb3 for assembly instructions) (113 cable type use drawing no. sma-j-c-x-st-sb4 for assembly instructions) sheet of micro rf cable assembly by: mhxxx-mhxrp-xxxxxx-xxxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing cummings 07/26/2005 2 2 sheet scale: 1:1 revision f f:\dwg\misc\mktg\mhxxx-mhxrp-xxxxxx-xxxx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
