jul 05, 2006 revised to dec 05, 2006 page 1 of 6 www.power-one.com blp30 ac-dc series data sheet 30 watts description the blp30 series? economical and compact construction provides single or three-output ac to dc power conversion to meet the requirements of most commercial and industrial applications. single-output model selection model nominal output voltage (vdc) min-max output current (amps), convection min-max output current (amps), forced air 1 peak output current (amps) 2 total regulation (%) 3 ripple & noise pk-pk % 4 BLP30-1005G 5v 0 ? 5 0 ? 6 7.2 2 1 blp30-1012g 12v 0 ? 2.1 0 ? 2.5 3.0 2 1 blp30-1024g 24v 0 ? 1.0 0 ? 1.25 1.5 2 0.6 triple-output model selection model nominal output voltage (vdc) min-max output current (amps), convection min-max output current (amps), forced air 1 peak output current (amps) 2 total regulation (%) 3 ripple & noise pk-pk % 4 +5v 0.2 ? 2.5 0.2 ? 3.5 5 2 1% blp30-3000g +12v 0.1 ? 1.2 0.1 ? 2.0 3 5 1% -12v 0.0 ? 0.3 0.0 ? 0.5 1 5 1% 1 10 cfm or 260 lfm (average measurement of six equally-distribut ed points through a 3.5" x 1.6" (9 cm x 4 cm) cross-sectional area with power supply mounted on a 0.25" (6.35 mm) standoffs. recommended airflow direction is from the ac input to the dc output. 2 peak current duration for less than 30 seconds with a max duty cycle of 10%. 3 at 25 c ambient including voltage set point tolerance, line, and load regulation 4 maximum peak-to-peak noise expressed as a percentage of output voltage, 20 mhz bandwidth, measured with a twisted pair differen tially across a 10 f e-cap and a 0.1 f ceramic cap in parallel. the poi nt of measurement is within 1 cm of the output connection. applications ? datacom (hubs, routers) ? pos terminals ? industrial ? cable modems ? external disk storage ? medical instrumentation ? computers features ? rohs compliant for all six substances ? 2? x 4? footprint ? component height less than 1? ? 25 w rating with natural convection cooling ? 30 w rating with 10 cfm airflow ? compliance to emi class b ? universal ac input ? short-circuit protection ? overvoltage protection ? ce marked to low voltage directive (pending) ? compliance to en61000-4-2/-3/-4/-5/-6/-8/-11 ? two-year warranty
jul 05, 2006 revised to dec 05, 2006 page 2 of 6 www.power-one.com blp30 ac-dc series data sheet 30 watts electrical specifications input specifications parameter conditions/descripti on min. nom. max. units input voltage - ac single-phase cont inuous input range 90 100 - 250 264 vac input voltage - dc 127 160/325 375 vdc input frequency ac input 47 50 - 60 63 hz input current at 90 vac input., 30w 0.75 a rms inrush surge current internally limited. 115 vac, max power, 25 c internally limited. 230 vac, max power, 25 c 16 32 a pk a pk input fuse non-user serviceable internally located ac input line fuse is provided. efficiency at maximum output power. 70 75 % switching frequency 60 69 khz output specifications parameter conditions/descripti on min. nom. max. units output power with convection cooling. see model selection. with forced-air cooling. see model selection. 25 30 watts load transient vo1, vo2, or vo3 deviation due to a 50 to 100% load change at a rate of 1a/s. 5 % turn on delay time required for outputs to be within regulation after initial application of ac input. 1.5 sec rise time time required for output voltage to rise from 10% to 90%. 20 ms hold-up time at 30w, 115 vac, 60 hz. 20 ms overvoltage protection main output. 5v: 12v: 24v: 5.6 14.0 29.0 6.9 16.7 34.2 v short-circuit protection fully-protected against output short circuit. overshoot single-output models. 2 % overshoot triple-output models. 5 %
jul 05, 2006 revised to dec 05, 2006 page 3 of 6 www.power-one.com blp30 ac-dc series data sheet 30 watts regulatory & safety approvals parameter conditions/descripti on min. nom. max. units ul60950-1 all models are approved. csa-c22.2, no. 60950-1-03 all models are approved. en 60950-1 /iec 60950-1 all models are approved. ce mark for lvd all models are approved. cb approval completed. ground continuity at 12 vdc. 30 a dielectric withstand voltage input-to-ground (basic) . input-to-output (reinfor ced). the primary to secondary test is not performed on completed assemblies. output-to-ground (functional). 2121 4242 500 vdc vdc vdc electromagnetic interference fcc part 15. conducted: cispr 22 and cispr 11. conducted: b b class esd per en 61000-4-2, level 2. radiated susceptibility per en 610 00-4-3, level 3. 3 v/m eft/burst per en 61000-4-4, level 3. 1 kv input transient protection per en 61000-4-5, class 3. line-to-line: line-to-ground: 1 2 kv rf immunity per en 61000-4-6, level 3. 3 v/m magnetic fields per en 61000-4-8. 1 a/m voltage interruptions per en 61000-4-11 leakage current per en 60950 at 115 vac: at 230 vac: 0.2 0.4 ma
jul 05, 2006 revised to dec 05, 2006 page 4 of 6 www.power-one.com blp30 ac-dc series data sheet 30 watts environmental specifications parameter conditions/descripti on min. nom. max. units altitude operating. non-operating. 10k 50k asl ft asl ft operating temp 0 oc to 70 oc with linear derating to 50% above 50 oc. unit will start-up at -20 oc, but will not meet all published specifications. 0 50 70 oc storage temp -40 85 oc temperature coefficient 0 oc to 70 oc (after 15-minute warm-up). 0.02 %/ oc relative humidity 95% relative humidity @ 40 oc, non-condensing 95 %rh shock operating: half-sine, 11 3 ms, 3-axis. non-operating: half-sine, 11 3 ms, 3-axis. 15 40 g g vibration operating: random vibration; 5 to 500 hz (10 minutes, each axis). non-operating: random vibration; 5 to 500 hz (10 minutes, each axis). 2.4 6 grms grms
jul 05, 2006 revised to dec 05, 2006 page 5 of 6 www.power-one.com blp30 ac-dc series data sheet 30 watts mechanical drawing ? single output models all dimensions are in inches. recommended mating connectors * housing pin cn1 and cn2 molex 22-01-2051 molex 08-52-0123 molex 22-01-2057 molex 08-52-0101 molex 22-01-3057 leoco 2530s05000 leoco 2533tpb0000 * equivalent housings and pi ns can also be used. 4.00 +/- 02 2.07 +/-.02 1.07 +/-.02 0.91 0.1 0.06 3.750 1.750 ? 0.16 (4 places) printed circuit board fastener clearance area 0.25 dia (4 places) cn1 input connector cn2 - dc output connector (see pin-out table) pin 1 vout pin 2 dc com pin 3 vout pin 4 dc com pin 5 vout top view side view end view cn2 - dc con pin 1 ac neutral pin 3 ac line pin 5 ac ground cn1 - ac conn. pin #1 pin #1 pcb ac ground connection point - solder side
jul 05, 2006 revised to dec 05, 2006 page 6 of 6 www.power-one.com blp30 ac-dc series data sheet 30 watts mechanical drawing ? triple output model all dimensions are in inches. recommended mating connectors * housing pin cn1 and cn2 molex 22-01-2051 molex 08-52-0123 molex 22-01-2057 molex 08-52-0101 molex 22-01-3057 leoco 2530s05000 leoco 2533tpb0000 * equivalent housings and pi ns can also be used. nuclear and medical applications - power-one products are not des igned, intended for use in, or authorized for use as critical components in life support systems, equipment used in hazardous envir onments, or nuclear control systems without the express wr itten consent of the respective divisional pr esident of power-one, inc. technical revisions - the appearance of products, including safe ty agency certifications pictured on labels, may change dependi ng on the date manufactured. specifications ar e subject to change without notice. 4.00 +/- 02 2.00 +/-.02 1.07 +/-.02 0.91 0.1 0.06 3.750 1.750 ? 0.16 (4 places) printed circuit board fastener clearance area 0.25 dia (4 places) cn1 input connector cn2 - dc output connector (see pin-out table) pin 1 vo3 pin 2 dc com pin 3 vo1 pin 4 dc com pin 5 vo2 top view side view end view cn2 - dc con pin 1 ac neutral pin 3 ac line pin 5 ac ground cn1 - ac conn. pin #1 pin #1 pcb ac ground connection point - solder side
|
