gamewell-fci 12 clintonville road, northford, ct 06472-1610 usa ? tel: (203) 484-7161 ? fax: (203) 484-7118 specifications are for information only, are not intended for installation purposes, and are subject to change without notice. no responsibility is assumed by gamewell-fci for their use. ?2007 honeywell international inc. all rights reserved. www.gamewell-fci.com cs-2045 rev. a page 1 of 2 RCE-95 relay control elements description the gamewell-fci relay control element (RCE-95) is the interface between the gamewell-fci 600 series fire alarm control panel (facp) analog circuits and building functions such as door holders, elevators, dampers, motors and disconnects. the RCE-95 offers feedback input points for positive confirmation of the controlled device?s activity. the RCE-95 works with all 600 series analog addressable facps. for annunciation and feed- back at the panel, gamewell-fci offers a relay control display (rcd). the rcd is only available with the if632 and if650 facps. the RCE-95 is either surface or flush mounted and has an integral led which annunciates upon device activation. operation the devices connect to the slc circuit of the facp via a two-wire non- polarized circuit. in its quiescent mode, the RCE-95 monitors its internal circuitry for status of the device itself and supervises an external control circuit for status. when a status change is detected, the event can be pro- grammed to display on the optional rcd module. when an event is reported to the control panel that requires the activation of the RCE-95, the control panel communicates via the analog circuit to the RCE-95 for activation. the integral led is also lit for annunciation at the device. programming the RCE-95 is programmed by setting a single dip switch easily accessible on the RCE-95?s printed circuit board. the dip switch is used to set the address of the device. all other programming is accomplished at the fire alarm con- trol panel, either through a laptop computer or the control panel operator?s display. features ? compatible with the gamewell-fci 600 series analog addressable facps. ? form-c dry relay contacts. ? event or manual controllable relay functions. ? positive feedback of relay activation. ? led annunciates activation. ? fully supervised. ? surface or flush mounting. ? field programmable. ? style 4, 6 , or 7 wiring. ? screw terminals for field wiring connections. microsoft ? windows ? is a registered trademark of microsoft ? corporation. cs-2054ph1.wmf RCE-95 an iso 9000-2000 company approved fm signaling s521 7300-1288:147
gamewell-fci 12 clintonville road, northford, ct 06472-1610 usa ? tel: (203) 484-7161 ? fax: (203) 484-7118 cs-2045 rev. a page 2 of 2 www.gamewell-fci.com mounting the RCE-95 is designed to mount in a standard 4.688" (11.908 cm) electrical backbox. the RCE-95 should be mounted in an easily visible location so that the built-in led may be seen for quick indication of proper connection and activation. engineer?s specifications a programmable interface device shall be provided for the control and status reporting of programmed relay control functions. the RCE-95 shall communicate with the fire alarm control panel via an analog circuit (slc) over a sin- gle pair of wires. the device shall provide dry contacts and positive feed- back of the controlled equipment?s status annunciating upon activation. it shall be gamewell-fci RCE-95. specifications input power: 24 vdc from analog circuit standby current: 0.0005 a alarm current: 0.0015 a operating temperature: 0 c to 49c (32f to 120f) relative humidity: 85% non-condensing housing requirements: 4.688" (11.908 cm) backbox contact rating: 2.0 amp at 30 vdc 0.2 a at 120 vac ordering information model description RCE-95 relay control element device. xp95 protocol compatible. 70839 trim ring for flush mounting the RCE-95. rcd optional relay control display; provides annunciation of the RCE-95 control element devices at the facp. one needed for every eight rces. compatible only with the if632 and if650 facps
|