12345678 on .020 .002 (0,51 0,05) typ. .052 .002 (1,32 0,13) typ. .085 .005 (2,16 0,13) typ. .100 .005 (2,54 0,13) typ. c l c l length .010 (0,25) see chart .160 .005 (4,19 0,13) .220 (5,59) max. .085 .005 (2,16 0,13) typ. .020 .002 (0,51 0,05) typ. .100 .010 (2,54 0,25) typ. c l c l .320 (8,13) max. .290 (7,37) max. .012 .001 (0,30 0,03) typ. .250 .010 (6,35 0,25) .290 (7,37) max. .012 .002 (0,30 0,05) .395 .010 (10,03 0,25) length .010 (0,25) see chart .160 .005 (4,19 0,13) .190 (4,83) max. .004 (0,10) .004 (0,10) switch is packaged as shown here with all positions on .350 (8,90) typ. .150 (3,81) typ. .100 (2,54) typ. .100 (2,54) typ. .070 (1,78) typ. c l c l .500 (12,7) typ. .250 (6,35) typ. .125 (3,18) typ. .100 (2,54) typ. .070 (1,78) typ. c l c l series 90hb spst, low profle fe atures ? compatible with smt assembly, including infrared refow and vapor-phase ? reliable spring and ball contact dimensions in inches (and millimeters) top viewCgull wing circuitr y as viewed from the top of the switch in the positions shown in the drawing. recommended pc pad dimensionsCgull wing recommended pc pad dimensionsCj-bend gull wing j-bend dip 5 surface mount dip switches grayhill, inc. ? 561 hillgrove avenue ? lagrange, illinois 60525-5997 ? usa ? phone: 708-354-1040 ? fax: 708-354-2820 ? www.grayhill.com dip switches
series terminal style: w = gull wing, j = j-bend rohs compliant 90hbw02prt packaging: r = tape and reel packaging (750 switches/reel) blank = tube packaging (each tube is 19.5" long) seal: p = polyimide seal blank = no seal number of positions: 02 through 10 surface mount dip switches meets requirements of eia 481-2 or eia 481-3 each reel has a 15.750 inch (390 mm) minimum leader and a 6.30 inch (160 mm) minimum trailer. t ape and reel p ac k aging 13 inch diameter reel direction of feed 24mm tape 16mm 32 & 44mm tape 16mm pin one location conductive plastic embossed tape specification s electrical ratings make-and-break c urrent rating: 2,000 operations per switch position at these resistive loads:10 ma, 30 vdc; or 10 ma, 50 mvdc; 10 ma, 50 mvdc; or 25 ma, 24 vdc; or 100 ma,6 vdc. c ontact resistance: (measured at 10 ma, 50 mvdc). initial: 20 mohms maximum, after life: 100 mohms maximum insulation resistance: minimum, at 100 vdc between adjacent closed contacts and also across open switch contacts. initial (mohms): 5,000, after life (mohms): 1,000 dielectric strength: minimum voltage (ac rms) measured between adjacent closed contacts and also across open switch contacts. lnitial: 500 volts, after life: 500 volts current c arry rating: 3a maximum rise of 20c switch capacitance: 2 pf at 1 megahertz mechanical ratings where grayhill performance is superior, the mil spec is listed in parentheses. mechanical life: 2,000 operations per switch position vibration resistance: per method 204, test condition b , 1ms opening (10 ms allowed) mechanical shock: per method 213, test condition a. 1ms opening (10 ms allowed) t hermal shock resistance: per specifcation; no failures; passes contact resistance. t erminal strength: per specifcation thermal aging: 1,000 hours at 85c; no failures. e nvironmental ratings meets all requirements of mil- s-83504**. operating t emperature range: -40c to + 85c storage t emperature range: -40c to + 85c moisture resistance: per mil-std-202, method 106. soldering i nformation solderability: per mil-std-202, method 208 soldering heat resistance: per mil-s-83504, six second test. recommended p rocessing t emperature: 220cC230c (1 pass260c maximum) p rocessing p osition: switch is to be processed with all actuators in the closed (on) position as shipped. fluxing: per eia rs-448-2 with fux touching switch body. cleaning: passes immersion test using water/ detergent. acceptable solutions include 1-1-1 trichlorethane, freon, (tf, te, or tms), isopropyl alcohol, detergent (140f maximum). terpene acceptable for series 90 only. solutions which are not recommended include acetone, methylene chloride, freon tmc. high pressure aqueous cleaning is not recommended. materials and finishes shorting member (ball): brass, gold-plate over nickel barrier. base contacts: copper alloy, gold-plate over nickel barrier. t erminals: copper alloy, matte tin plated over nickel barrier. non-conductive p arts: ther moplastic (u l94v-o) t ape and reel p ackaging t ape seal integrity: passes gross leak test using 125c fourinert for 20 seconds minimum. reference mil-std-202, method 112 t ape seal: polyimide flm ordering inform ation available from your local grayhill distributor. for prices and discounts, contact a local sales offce, an authorized local distributor or grayhill. ** note: 100% matte tin terminal plating does not meet mil-s-83504 for lead content. no. of length length number positions inches metric per tube 2 .270" 6,9 mm 60 3 .370" 9,4 mm 47 4 .470" 11,9 mm 37 5 .570" 14,5 mm 31 6 .670" 17,0 mm 26 7 .770" 19,6 mm 23 8 .870" 22,1 mm 20 9 .970" 24,6 mm 18 10 1.070" 27,2 mm 16 dip 6 dip switches grayhill, inc. ? 561 hillgrove avenue ? lagrange, illinois 60525-5997 ? usa ? phone: 708-354-1040 ? fax: 708-354-2820 ? www.grayhill.com
|
