designed & dimensioned in millimeters[inches] this product manufactured with lead-free processing pb do not scale from this print 16.00 .630 (hex) ref 17.50 (hex) ref .689 18.70 ref .736 13.00 ref .512 12.50 ref .492 10.29 ref .405 to mating reference plane 1 2 3 4 5 6 7 8 13.00 .512 12.10 .476 5.60 .220 recommended mounting hole 4.00[.157] max panel thickness BNC7T-J-C-XX-ST-BH3 -st: straight orientation -bh3: bulkhead 3 (rg179 cable) termination plating specification -c: cable type -j: jack gender -hn: 30" gold center contact, 100" nickel outer contact -gn: 10" gold center contact, 100" nickel outer contact (see table 1) c sheet of unless otherwise specified, dimensions are in millimeters [inches]. tolerances are: decimals angles .x: 0.3 [.01] 5 .xx: 0.13 [.005] .xxx: 0.051 [.0020] material: true 75 ohm, bnc st cable plug, rg 179 by: BNC7T-J-C-XX-ST-BH3 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing g herman 06/25/2008 2 1 sheet scale: 2:1 f:\dwg\misc\mktg\BNC7T-J-C-XX-ST-BH3-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 notes: 1. represents a critical dimension. 2. note deleted. 3. note deleted. 4. note deleted. 5. product to be packaged per packaging standard co-hd-wi-3040m. 6. note deleted. 7. note deleted. 8. note deleted. shell, ferrules, nut, washer: brass contact: copper alloy dielectric: ptfe gasket: silicone revision n
4.60 0.30 .181 .012 8.20 0.30 .323 .012 17.90 0.30 .705 .012 rg179 cable c c in process 1 strip and tin inner conductor c 20.0 2.5 .79 .10 hst-0.187-02-blk 8 in process 2 add heat shrink tube and ferrule 'b' in process 3 flare shield, add inner ferrule and insulator 0.10 gap max allowable .004 c 5 in process 4 solder signal socket 'a' 4 in process 5 add sub assembly 0.6 [0.03] gap max allowable 22.20 ref .874 1 2 3 in process 7 apply heat shrink tube & add gasket 3.16 ref .124 detail 'a' scale 2.5 : 1 0.25 gap max allowable .010 4.52 hex crimp .178 (across 2 faces) c c in process 6 crimp ferrule (use rf crimp hand tool #cat-ht-126667-21 or equivalent) detail 'b' scale 2.5 : 1 (assemble with tapered end under braid) insulator washer and inner ferrule to be flush with cable dielectric 6 7 sheet of true 75 ohm, bnc st cable plug, rg 179 by: BNC7T-J-C-XX-ST-BH3 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing g herman 06/25/2008 2 2 sheet scale: 5:4 revision n f:\dwg\misc\mktg\BNC7T-J-C-XX-ST-BH3-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
