- 392 - F1T1 thru f1t7 1.0 amp. fast recovery rectifiers voltage range 50 to 1000 volts current 1.0 ampere f eatures low forward voltage drop high current capability high reliability high surge current capability m echanical data cases: molded plastic epoxy: ul 94v-0 rate flame retardant lead: axial leads, solderable per mil- std-202, method 208 guaranteed polarity: color band denotes cathode end high temperature soldering guaranteed: 260 /10 seconds/.375?,(9.5mm) lead lengths at 5 lbs.,(2.3kg) tension weight: 0.20 gram ts-1 dimensions in inches and (millimeters) m aximum ratings and electrical characteristics rating at 25 ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% type number symbol F1T1 f1t2 f1t3 f1t4 f1t5 f1t6 f1t7 unit s maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward rectified current .375?(9.5mm) lead length @t a = 55 i (av) 1.0 a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method ) i fsm 30 a maximum instantaneous forward voltage @ 1.0a v f 1.2 v maximum dc reverse current @ t a =25 at rated dc blocking voltage @ t a =100 i r 5.0 100 ua ua maximum reverse recovery time ( note 1 ) trr 150 250 500 ns typical junction capacitance ( note 2 ) cj 10 pf typical thermal resistance ( note 3 ) r ja 100 o c/w operating temperature range t j -65 to +150 storage temperature range t stg -65 to +150 notes: 1. reverse recovery test conditions: i f =0.5a, i r =1.0a, i rr =0.25a 2. measured at 1 mhz and applied reverse voltage of 4.0 volts d.c. 3. mount on cu - pad size 5mm x 5mm on p.c.b.
- 393 - ratings and characteristic curves (F1T1 thru f1t7) fig.5- reverse recovery time characteristic and test circuit diagram 50 noninductive non inductive oscilloscope (note 1) pulse generator (note 2) dut (+) 50vdc (approx) (-) notes: 1. rise time=7ns max. input impedance= 1 megohm 22pf 2. rise time=10ns max. sourse impedance= 50 ohms (-) (+) 10 noninductive -1.0a -0.25a 0 +0.5a trr 1cm set time base for 5/ 10ns/ cm fig.2- maximum non-repetitive forward surge current peak for ward surge current . (a) 1 2 4 6 8 10 20 100 40 60 80 20 10 0 40 50 30 number of cycles at 60hz 8.3ms single half sine wave jedec method fig.3- typical forward characteristics instantaneous for ward current . (a) 1.6 1.8 0.4 0.6 0.8 1.0 1.2 1.4 0.03 0.1 0.3 1 10 20 3 0.01 forward voltage. (v) tj=25 c pulse width=300 s 1% duty cycle o fig.4- typical junction capacitance junction cap acitance.(pf) 1 2 4 6 10 100 60 40 20 10 1 30 50 90 reverse voltage. (v) tj=25 c 0 fig.1- maximum typical forward current derating curve average for ward current . (a) 25 0 50 75 100 125 150 175 0.5 0 0.25 0.75 1.0 ambient temperature. ( c) o single phase half wave 60hz resistive or inductive load 0.375" (9.5mm) lead length 20
|