View UPC29M07T-E2-AY_6630037.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

data sheet bipolar analog integrated circuit pc29mxx series three terminal low dropout voltage regulator the pc29mxx series of low dropout voltage three terminal positive regulators is constructed with pnp output transistor. the pc29mxx series feature the ability to source 0.5 a of output current with a low dropout voltage of typically 0.5 v. the power dissipation of the pc29mxx series can be drastically reduced compared with the conventional three terminal positive voltage regulators that is constructed with npn output transistor. also, this series corresponds to the low voltage output (3.0 v, 3.3 v) which is not in the conventional low dropout regulators ( pc24mxxa series). features output current in excess of 0.5 a low dropout voltage v dif = 0.5 v typ. (i o = 0.5 a) on-chip over-current and thermal protection circuit on-chip output transistor safe operating area protection circuit pin configurations (marking side) 3 2 1 1: input 2: gnd 3: output pc29mxxhf series: isolated to-220 (mp-45g) pc29mxxhb series: sc-64 (mp-3) pc29mxxt series: sc-63 (mp-3z) 4 3 2 1 1: input 2: gnd 3: output 4: gnd (fin) note1 4 3 2 1 1: input 2: gnd 3: output 4: gnd (fin) note2 notes 1. no.2 pin and no.4 fin are common gnd. 2. no.2 pin is cut. no.2 pin and no.4 fin are common gnd. document no. g10027ej4v0ds00 (4th edition) date published september 2007 n printed in japan the information in this document is subject to change without notice. before using this document, please confirm that this is the latest version. not all products and/or types are available in every country. please check with an nec electronics sales representative for availability and additional information. the mark shows major revised points. the revised points can be easily searched by copying an "" in the pdf file and specifying it in the "find what." field.
pc29mxx series 2 data sheet g10027ej4v0ds block diagram start-up circuit reference voltage thermal shut down error amp. drive circuit saturation protection safe operating area protection output gnd input over-current protection
pc29mxx series 3 data sheet g10027ej4v0ds ordering information part number package output voltage marking pc29m03hf isolated to-220 (mp-45g) 3.0 v 29m03 pc29m03hb sc-64 (mp-3) 3.0 v 29m03 pc29m03t sc-63 (mp-3z) 3.0 v 29m03 pc29m33hf isolated to-220 (mp-45g) 3.3 v 29m33 pc29m33hb sc-64 (mp-3) 3.3 v 29m33 pc29m33t sc-63 (mp-3z) 3.3 v 29m33 pc29m05hf isolated to-220 (mp-45g) 5.0 v 29m05 pc29m05hb sc-64 (mp-3) 5.0 v 29m05 pc29m05t sc-63 (mp-3z) 5.0 v 29m05 pc29m06hf isolated to-220 (mp-45g) 6.0 v 29m06 pc29m06hb sc-64 (mp-3) 6.0 v 29m06 pc29m06t sc-63 (mp-3z) 6.0 v 29m06 pc29m07hf isolated to-220 (mp-45g) 7.0 v 29m07 pc29m07hb sc-64 (mp-3) 7.0 v 29m07 pc29m07t sc-63 (mp-3z) 7.0 v 29m07 pc29m08hf isolated to-220 (mp-45g) 8.0 v 29m08 pc29m08hb sc-64 (mp-3) 8.0 v 29m08 pc29m08t sc-63 (mp-3z) 8.0 v 29m08 pc29m09hf isolated to-220 (mp-45g) 9.0 v 29m09 pc29m09hb sc-64 (mp-3) 9.0 v 29m09 pc29m09t sc-63 (mp-3z) 9.0 v 29m09 pc29m10hf isolated to-220 (mp-45g) 10.0 v 29m10 pc29m10hb sc-64 (mp-3) 10.0 v 29m10 pc29m10t sc-63 (mp-3z) 10.0 v 29m10 pc29m12hf isolated to-220 (mp-45g) 12.0 v 29m12 pc29m12hb sc-64 (mp-3) 12.0 v 29m12 pc29m12t sc-63 (mp-3z) 12.0 v 29m12 remark tape-packaged products have the symbol -e1, or -e2 suffixed to the part number. pb-free products have the symbol -az, or -ay suffixed to the part number. refer to the following table for details.
pc29mxx series 4 data sheet g10027ej4v0ds part number note1 package packege type pc29mxxhf isolated to-220 (mp-45g) ?packed in envelop pc29mxxhf-az note2 isolated to-220 (mp-45g) ?packed in envelop pc29mxxhb sc-64 (mp-3) ?packed in envelop pc29mxxhb-az note2 sc-64 (mp-3) ?packed in envelop pc29mxxhb-ay note3 sc-64 (mp-3) ?packed in envelop pc29mxxt-e1 sc-63 (mp-3z) ?16 mm wide embossed taping ?pin 1 on draw-out side ?2000 pcs/reel pc29mxxt-e1-az note2 sc-63 (mp-3z) ?16 mm wide embossed taping ?pin 1 on draw-out side ?2000 pcs/reel pc29mxxt-e1-ay note3 sc-63 (mp-3z) ?16 mm wide embossed taping ?pin 1 on draw-out side ?2000 pcs/reel pc29mxxt-e2 sc-63 (mp-3z) ?16 mm wide embossed taping ?pin 1 at take-up side ?2000 pcs/reel pc29mxxt-e2-az note2 sc-63 (mp-3z) ?16 mm wide embossed taping ?pin 1 at take-up side ?2000 pcs/reel pc29mxxt-e2-ay note3 sc-63 (mp-3z) ?16 mm wide embossed taping ?pin 1 at take-up side ?2000 pcs/reel notes 1. xx stands for symbols that indicate the output voltage. 2. pb-free (this product does not contain pb in the external electrode.) 3. pb-free (this product does not contain pb in the external electrode, sn100% plating.)
pc29mxx series 5 data sheet g10027ej4v0ds absolute maximum ratings (t a = 25 c, unless otherwise specified.) parameter symbol rating unit pc29mxxhf pc29mxxhb, pc29mxxt input voltage v in 20 v internal power dissipation (t c = 25 c) note p t 15 10 w operating ambient temperature t a ?0 to +85 c operating junction temperature t j ?0 to +150 c storage temperature t stg ?5 to +150 c thermal resistance (junction to case) r th (j-c) 7 12.5 c/w thermal resistance (junction to ambient) r th (j-a) 65 125 c/w note internally limited. when the operating junction temperature rises above 150 c, the internal circuit shuts down the output voltage. caution product quality may suffer if the absolute maximum rating is exceeded even momentarily for any parameter. that is, the absolute maximum ratings are rated values at which the product is on the verge of suffering physical damage, and therefore the product must be used under conditions that ensure that the absolute maximum ratings are not exceeded. typical connection d 1 pc29mxx input c out c in d 2 + output c in : 0.1 f or higher. be sure to connect c in to prevent parasitic oscillation. set this value according to the length of the line between the regulator and the input pin. use of a film capacitor or other capacitor with first-rate voltage and temperature characteristics is recommended. if using a laminated ceramic capacitor, it is necessary to ensure that c in is 0.1 f or higher for the voltage and temperature range to be used. c out : 47 f or higher. be sure to connect c out to prevent oscillation and improve excessive load regulation. place c in and c out as close as possible to the ic pins (within 1 to 2 cm). also, use an electrolytic capacitor with low impedance characteristics if considering use at sub-zero temperatures. d 1 : if the output pin has a higher voltage than the input pin, connect a diode. d 2 : if the output pin has a lower voltage than the gnd pin, connect a schottky barrier diode. caution make sure that no voltage is applied to the output pin from external.
pc29mxx series 6 data sheet g10027ej4v0ds recommended operating conditions parameter symbol type number min. typ. max. unit input voltage v in pc29m03 4 16 pc29m33 4.3 16 pc29m05 6 16 pc29m06 7 16 pc29m07 8 16 v pc29m08 9 18 pc29m09 10 18 pc29m10 11 18 pc29m12 13 18 output current i o all 0 0.5 a operating ambient temperature t a all ?0 +85 c operating junction temperature t j all ?0 +125 c electrical characteristics pc29m03 (t j = 25 c, v in = 5 v, i o = 350 ma, c in = 0.22 f, c out = 47 f, unless otherwise specified.) parameters symbol conditions min. typ. max. unit output voltage v o 2.88 3.0 3.12 0 c t j 125 c, 4.0 v v in 16 v, v 0 a i o 350 ma 2.85 3.15 0 c t j 125 c, 0 a i o 0.5 a line regulation reg in 4.0 v v in 16 v 7 30 mv load regulation reg l 0 a i o 0.5 a 8 30 mv quiescent current i bias i o = 0 a 1.8 4.0 ma i o = 0.5 a 17 30 startup quiescent current i bias (s) v in = 2.95 v, i o = 0 a 7 30 ma v in = 2.95 v, i o = 0.5 a 80 quiescent current change ? i bias 0 c t j 125 c, 4.0 v v in 16 v 3.2 20 ma output noise voltage v n 10 hz f 100 khz 51 v r.m.s. ripple rejection r? f = 120 hz, 4.0 v v in 16 v 48 64 db dropout voltage v dif 0 c t j 125 c, i o = 0.5 a 0.5 1.0 v short circuit current i o short v in = 4.5 v 0.65 1.0 1.5 a v in = 16 v 0.6 peak output current i o peak v in = 4.5 v 0.7 1.0 1.5 a v in = 16 v 0.6 0.9 1.5 temperature coefficient of ? v o / ? t0 c t j 125 c, i o = 5 ma ?.3 mv/ c output voltage
pc29mxx series 7 data sheet g10027ej4v0ds pc29m33 (t j = 25 c, v in = 5 v, i o = 350 ma, c in = 0.22 f, c out = 47 f, unless otherwise specified.) parameters symbol conditions min. typ. max. unit output voltage v o 3.17 3.3 3.43 0 c t j 125 c, 4.3 v v in 16 v, v 0 a i o 350 ma 3.14 3.46 0 c t j 125 c, 0 a i o 0.5 a line regulation reg in 4.3 v v in 16 v 8 33 mv load regulation reg l 0 a i o 0.5 a 10 33 mv quiescent current i bias i o = 0 a 1.8 4.0 ma i o = 0.5 a 15 30 startup quiescent current i bias (s) v in = 3.1 v, i o = 0 a 9 30 ma v in = 3.1 v, i o = 0.5 a 80 quiescent current change ? i bias 0 c t j 125 c, 4.3 v v in 16 v 2.9 20 ma output noise voltage v n 10 hz f 100 khz 56 v r.m.s. ripple rejection r? f = 120 hz, 4.3 v v in 16 v 48 64 db dropout voltage v dif 0 c t j 125 c, i o = 0.5 a 0.5 1.0 v short circuit current i o short v in = 4.5 v 0.7 1.1 1.5 a v in = 16 v 0.6 peak output current i o peak v in = 4.5 v 0.7 1.2 1.5 a v in = 16 v 0.6 1.0 1.5 temperature coefficient of ? v o / ? t0 c t j 125 c, i o = 5 ma ?.4 mv/ c output voltage
pc29mxx series 8 data sheet g10027ej4v0ds pc29m05 (t j = 25 c, v in = 8 v, i o = 350 ma, c in = 0.22 f, c out = 47 f, unless otherwise specified.) parameters symbol conditions min. typ. max. unit output voltage v o 4.8 5.0 5.2 0 c t j 125 c, 6 v v in 16 v, v 0 a i o 350 ma 4.75 5.25 0 c t j 125 c, 0 a i o 0.5 a line regulation reg in 6 v v in 16 v 26 50 mv load regulation reg l 0 a i o 0.5 a 17 50 mv quiescent current i bias i o = 0 a 1.9 4.0 ma i o = 0.5 a 16 30 startup quiescent current i bias (s) v in = 4.5 v, i o = 0 a 10 30 ma v in = 4.5 v, i o = 0.5 a 80 quiescent current change ? i bias 0 c t j 125 c, 6 v v in 16 v 2.4 20 ma output noise voltage v n 10 hz f 100 khz 87 v r.m.s. ripple rejection r? f = 120 hz, 6 v v in 16 v 46 60 db dropout voltage v dif 0 c t j 125 c, i o = 0.5 a 0.5 1.0 v short circuit current i o short v in = 6.5 v 0.65 1.1 1.5 a v in = 16 v 0.6 peak output current i o peak v in = 6.5 v 0.7 1.2 1.5 a v in = 16 v 0.6 1.1 1.5 temperature coefficient of ? v o / ? t0 c t j 125 c, i o = 5 ma 0.7 mv/ c output voltage
pc29mxx series 9 data sheet g10027ej4v0ds pc29m06 (t j = 25 c, v in = 9 v, i o = 350 ma, c in = 0.22 f, c out = 47 f, unless otherwise specified.) parameters symbol conditions min. typ. max. unit output voltage v o 5.76 6.0 6.24 0 c t j 125 c, 7 v v in 16 v, v 0 a i o 350 ma 5.70 6.30 0 c t j 125 c, 0 a i o 0.5 a line regulation reg in 7 v v in 16 v 30 60 mv load regulation reg l 0 a i o 0.5 a 30 60 mv quiescent current i bias i o = 0 a 2.0 4.0 ma i o = 0.5 a 16 30 startup quiescent current i bias (s) v in = 5.5 v, i o = 0 a 10 30 ma v in = 5.5 v, i o = 0.5 a 80 quiescent current change ? i bias 0 c t j 125 c, 7 v v in 16 v 2.5 20 ma output noise voltage v n 10 hz f 100 khz 126 v r.m.s. ripple rejection r? f = 120 hz, 7 v v in 16 v 42 58 db dropout voltage v dif 0 c t j 125 c, i o = 0.5 a 0.5 1.0 v short circuit current i o short v in = 7.5 v 0.7 1.1 1.5 a v in = 16 v 0.6 peak output current i o peak v in = 7.5 v 0.7 1.1 1.5 a v in = 16 v 0.6 1.1 1.5 temperature coefficient of ? v o / ? t0 c t j 125 c, i o = 5 ma 0.44 mv/ c output voltage
pc29mxx series 10 data sheet g10027ej4v0ds pc29m07 (t j = 25 c, v in = 10 v, i o = 350 ma, c in = 0.22 f, c out = 47 f, unless otherwise specified.) parameters symbol conditions min. typ. max. unit output voltage v o 6.72 7.0 7.28 0 c t j 125 c, 8 v v in 16 v, v 0 a i o 350 ma 6.65 7.35 0 c t j 125 c, 0 a i o 0.5 a line regulation reg in 8 v v in 16 v 35 70 mv load regulation reg l 0 a i o 0.5 a 35 70 mv quiescent current i bias i o = 0 a 2.0 4.0 ma i o = 0.5 a 16 30 startup quiescent current i bias (s) v in = 6.5 v, i o = 0 a 10 30 ma v in = 6.5 v, i o = 0.5 a 80 quiescent current change ? i bias 0 c t j 125 c, 8 v v in 16 v 2.6 20 ma output noise voltage v n 10 hz f 100 khz 147 v r.m.s. ripple rejection r? f = 120 hz, 8 v v in 16 v 40 56 db dropout voltage v dif 0 c t j 125 c, i o = 0.5 a 0.5 1.0 v short circuit current i o short v in = 8.5 v 0.7 1.1 1.5 a v in = 16 v 0.6 peak output current i o peak v in = 8.5 v 0.7 1.2 1.5 a v in = 16 v 0.6 1.1 1.5 temperature coefficient of ? v o / ? t0 c t j 125 c, i o = 5 ma 0.7 mv/ c output voltage
pc29mxx series 11 data sheet g10027ej4v0ds pc29m08 (t j = 25 c, v in = 11 v, i o = 350 ma, c in = 0.22 f, c out = 47 f, unless otherwise specified.) parameters symbol conditions min. typ. max. unit output voltage v o 7.68 8.0 8.32 0 c t j 125 c, 9 v v in 18 v, v 0 a i o 350 ma 7.6 8.4 0 c t j 125 c, 0 a i o 0.5 a line regulation reg in 9 v v in 18 v 40 80 mv load regulation reg l 0 a i o 0.5 a 40 80 mv quiescent current i bias i o = 0 a 2.0 4.0 ma i o = 0.5 a 15 30 startup quiescent current i bias (s) v in = 7.5 v, i o = 0 a 10 30 ma v in = 7.5 v, i o = 0.5 a 80 quiescent current change ? i bias 0 c t j 125 c, 9 v v in 18 v 3.0 20 ma output noise voltage v n 10 hz f 100 khz 150 v r.m.s. ripple rejection r? f = 120 hz, 9 v v in 18 v 42 58 db dropout voltage v dif 0 c t j 125 c, i o = 0.5 a 0.5 1.0 v short circuit current i o short v in = 9.5 v 1.0 a v in = 18 v 0.55 peak output current i o peak v in = 9.5 v 0.7 1.2 1.5 a v in = 18 v 0.6 1.1 1.5 temperature coefficient of ? v o / ? t0 c t j 125 c, i o = 5 ma 0.7 mv/ c output voltage
pc29mxx series 12 data sheet g10027ej4v0ds pc29m09 (t j = 25 c, v in = 12 v, i o = 350 ma, c in = 0.22 f, c out = 47 f, unless otherwise specified.) parameters symbol conditions min. typ. max. unit output voltage v o 8.64 9.0 9.36 0 c t j 125 c, 10 v v in 18 v, v 0 a i o 350 ma 8.55 9.45 0 c t j 125 c, 0 a i o 0.5 a line regulation reg in 10 v v in 18 v 45 90 mv load regulation reg l 0 a i o 0.5 a 45 90 mv quiescent current i bias i o = 0 a 2.0 4.0 ma i o = 0.5 a 15 30 startup quiescent current i bias (s) v in = 8.5 v, i o = 0 a 10 30 ma v in = 8.5 v, i o = 0.5 a 80 quiescent current change ? i bias 0 c t j 125 c, 10 v v in 18 v 20 ma output noise voltage v n 10 hz f 100 khz 170 v r.m.s. ripple rejection r? f = 120 hz, 10 v v in 18 v 41 57 db dropout voltage v dif 0 c t j 125 c, i o = 0.5 a 0.5 1.0 v short circuit current i o short v in = 10.5 v 1.0 a v in = 18 v 0.55 peak output current i o peak v in = 10.5 v 0.7 1.2 1.5 a v in = 18 v 0.6 1.1 1.5 temperature coefficient of ? v o / ? t0 c t j 125 c, i o = 5 ma 0.8 mv/ c output voltage
pc29mxx series 13 data sheet g10027ej4v0ds pc29m10 (t j = 25 c, v in = 13 v, i o = 350 ma, c in = 0.22 f, c out = 47 f, unless otherwise specified.) parameters symbol conditions min. typ. max. unit output voltage v o 9.6 10.0 10.4 0 c t j 125 c, 11 v v in 18 v, v 0 a i o 350 ma 9.5 10.5 0 c t j 125 c, 0 a i o 0.5 a line regulation reg in 11 v v in 18 v 34 100 mv load regulation reg l 0 a i o 0.5 a 10 100 mv quiescent current i bias i o = 0 a 2.1 4.0 ma i o = 0.5 a 16 30 startup quiescent current i bias (s) v in = 9.5 v, i o = 0 a 10 30 ma v in = 9.5 v, i o = 0.5 a 80 quiescent current change ? i bias 0 c t j 125 c, 11 v v in 18 v 1.9 20 ma output noise voltage v n 10 hz f 100 khz 180 v r.m.s. ripple rejection r? f = 120 hz, 11 v v in 18 v 40 53 db dropout voltage v dif 0 c t j 125 c, i o = 0.5 a 0.5 1.0 v short circuit current i o short v in = 11.5 v 0.9 a v in = 18 v 0.5 peak output current i o peak v in = 11.5 v 0.7 1.2 1.5 a v in = 18 v 0.6 1.2 1.5 temperature coefficient of ? v o / ? t0 c t j 125 c, i o = 5 ma 0.9 mv/ c output voltage
pc29mxx series 14 data sheet g10027ej4v0ds pc29m12 (t j = 25 c, v in = 15 v, i o = 350 ma, c in = 0.22 f, c out = 47 f, unless otherwise specified.) parameters symbol conditions min. typ. max. unit output voltage v o 11.52 12 12.48 0 c t j 125 c, 13 v v in 18 v, v 0 a i o 350 ma 11.4 12.6 0 c t j 125 c, 0 a i o 0.5 a line regulation reg in 13 v v in 18 v 25 120 mv load regulation reg l 0 a i o 0.5 a 13 120 mv quiescent current i bias i o = 0 a 2.1 4.0 ma i o = 0.5 a 14 30 startup quiescent current i bias (s) v in = 11.5 v, i o = 0 a 10 30 ma v in = 11.5 v, i o = 0.5 a 80 quiescent current change ? i bias 0 c t j 125 c, 13 v v in 18 v 1.7 20 ma output noise voltage v n 10 hz f 100 khz 210 v r.m.s. ripple rejection r? f = 120 hz, 13 v v in 18 v 40 53 db dropout voltage v dif 0 c t j 125 c, i o = 0.5 a 0.5 1.0 v short circuit current i o short v in = 14 v 0.7 a v in = 18 v 0.5 peak output current i o peak v in = 14 v 0.7 1.2 1.5 a v in = 18 v 0.6 1.1 1.5 temperature coefficient of ? v o / ? t0 c t j 125 c, i o = 5 ma 1.2 mv/ c output voltage
pc29mxx series 15 data sheet g10027ej4v0ds typical characteristics 20 150 100 50 50 40 30 20 10 0 0.5 1.0 1.5 0510 15 20 24 6 810 12 14 16 18 20 0 ?0 ?00 ?50 ?00 15 10 5 1.92 1.0 0 05085 100 150 ?0 0 50 100 150 without heatsink with infinite heatsink solid line: pc29mxxhf series broken line: pc29mxxhb series pc29mxxt series p d - total power dissipation - w v o - output voltage - v v dif - dropout voltage - v p d vs t a ? v o vs t j v o vs v in ( pc29m33) v dif vs t j t a - operating ambient temperature - ?c ? v o - output voltage change - mv t j - operating junction temperature - ?c v in - input voltage - v t j - operating junction temperature - ?c 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.2 0 0.6 0.4 1.0 0.8 456 1 0 ?5 0 +25 +50 +75 +100 +125 +150 23 78 t j = 25?c t j = 25?c i o = 0.5 a i o = 0.5 a i o = 0.35 a i o = 0.35 a i o = 5 ma t j = 25?c t j = 125?c t j = 0?c i bias - quiescent current - ma i bias (i bias (s) ) vs v in ( pc29m33) v in - input voltage - v i o peak - peak output current - a i o peak vs v dif ( pc29m03) v dif - dropout voltage - v pc29m03 pc29m33 pc29m12 pc29m03 pc29m12 pc29m05 i o = 0.5 a i o = 5 ma i o = 0 a
pc29mxx series 16 data sheet g10027ej4v0ds 6 5 4 3 2 1 0 0.2 0.4 0.6 0.8 1.0 1.2 80 70 60 80 70 60 50 40 30 0 0.5 1.0 1.5 0510 15 20 0.1 0.2 0.3 0.4 0.5 50 40 30 20 0 10 100 1 k 10 k 100 k v o - output voltage - v v o vs i o ( pc29m03) r? vs f i o - output current - a r? - ripple rejection - db r? - ripple rejection - db f - frequency - hz t j = 25?c 4.3 v v in 16 v f = 120 hz t j = 25?c v in = 16 v v in = 4 v t j = 25?c t j = 125?c t j = 0?c r? vs i o i o - output current - a 1.0 0.8 0.6 0.4 0.2 0 0 0.1 0.2 0.3 0.4 0.5 t j = 25?c t j = 25?c v dif - dropout voltage - v v dif vs i o ( pc29m03) i o - output current - a i o peak - peak output current - a i o peak vs v dif ( pc29m05) v dif - dropout voltage - v pc29m03 pc29m12 pc29m03 pc29m12 i o = 0.5 a
pc29mxx series 17 data sheet g10027ej4v0ds package drawings pc29mxxhf series d 17.0 0.3 3pin plastic sip (mp-45g) note each lead centerline is located within 0.25 mm of its true position (t.p.) at maximum material condition. item millimeters p3hf-254b-4 g 0.25 h 2.54 (t.p.) a 10.0 0.2 i 5.0 0.3 u 2.4 0.5 v y 8.9 0.7 z 1.30 0.2 j k l 8.5 0.2 b 7.0 0.2 c 1.50 0.2 e f 0.75 0.10 m 8.5 0.2 n p 2.8 0.2 3.3 0.2 2.46 0.2 5.0 0.2 4.5 0.2 0.65 0.10 13 2 m a b e i d l m k y j h c fg z n p u v
pc29mxx series 18 data sheet g10027ej4v0ds pc29mxxhb series sc-64 (mp-3) (unit: mm) pc29mxxt series sc-63 (mp-3z) (unit: mm) 2.3 2.3 1.1 0.1 5.0 0.2 5.5 0.2 7.0 min. 13.7 min. 6.5 0.2 2.3 0.2 0.5 0.1 1.6 0.2 0.5 +0.2 ?.1 0.5 +0.2 ?.1 1.5 +0.2 ?.1 0.75 123 4 1 23 4 6.5 0.2 4.4 0.2 5.0 0.2 0.5 0.1 0.5 0.1 2.3 0.3 2.3 0.3 5.6 0.3 9.5 0.5 2.5 0.5 1.0 0.5 5.5 0.2 1.5 +0.2 2.3 0.2 0.5 0.1 note note 0.4 min. 0.5 typ. 0.15 0.15 ? 0.1 note the depth of notch at the top of the fin is from 0 to 0.2 mm.
pc29mxx series 19 data sheet g10027ej4v0ds recommended soldering conditions when soldering this product, it is highly recommended to observe the conditions as shown below. if other soldering processes are used, or if the soldering is perfomed under different condition, please make sure to consult with our sales offices. for more details, refer to the semiconductor device mount manual (http://www.necel.com/pkg/en/mount/index.html) surface mount devices pc29mxxt series: sc-63 (mp-3z) process conditions symbol infrared ray reflow peak temperature: 235 c or below (package surface temperature), ir35-00-3 reflow time: 30 seconds or less (at 210 c or higher), maximum number of reflow processes: 3 times or less. vps peak temperature: 215 c or below (package surface temperature), vp15-00-3 reflow time: 40 seconds or less (at 200 c or higher), maximum number of reflow processes: 3 times or less. partial heating method pin temperature: 350 c or below, p350 heat time: 3 seconds or less (per each side of the device). caution apply only one kind of soldering condition to a device, except for ?artial heating method? or the device will be damaged by heat stress. remark flux: rosin-based flux sith low chlorine content (chlorine 0.2 wt% or below) is recommended. pc29mxxt-az series note1 , pc29mxxt-ay series note2 : sc-63 (mp-3z) process conditions symbol infrared ray reflow peak temperature: 260 c or below (package surface temperature), ir60-00-3 reflow time: 60 seconds or less (at 220 c or higher), maximum number of reflow processes: 3 times or less. partial heating method pin temperature: 350 c or below, p350 heat time: 3 seconds or less (per each side of the device). notes 1. pb-free (this product does not contain pb in the external electrode.) 2. pb-free (this product does not contain pb in the external electrode, sn100% plating.) caution apply only one kind of soldering condition to a device, except for ?artial heating method? or the device will be damaged by heat stress. remark flux: rosin-based flux sith low chlorine content (chlorine 0.2 wt% or below) is recommended.
pc29mxx series 20 data sheet g10027ej4v0ds through-hole devices pc29mxxhf series, pc29mxxhf-az series note1 : isolated to-220 (mp-45g) pc29mxxhb series, pc29mxxhb-az series note1 , pc29mxxhb-ay series note2 : sc-64 (mp-3) process conditions symbol wave soldering solder temperature: 260 c or below, ws60-00-1 (only to leads) flow time: 10 seconds or less. partial heating method pin temperature: 350 c or below, p350 heat time: 3 seconds or less (per each pin). notes 1. pb-free (this product does not contain pb in the external electrode.) 2. pb-free (this product does not contain pb in the external electrode, sn100% plating.) caution for through-hole device, the wave soldering process must be applied only to leads, and make sure that the package body does not get jet soldered. caution on use when using the pc29mxx series at the input voltage which is lower than in the recommended operating condition, the high quiescent current flows through devices because the transistor of the output paragraph is saturated (refer to i bias ( i bias (s) ) vs v in curves in typical characteristics ?. the pc29mxx series have saturation protection circuits, but they sometimes need about 80 ma current. therefore the power supply on the input needs the enough current capacity to pass this quiescent current when the devices startup. reference documents user's manual usage of three terminal regulators document no.g12702e review of quality and reliability handbook document no.c12769e information voltage regulator of smd document no.g11872e semiconductor device mount manual http://www.necel.com/pkg/en/mount/index.html
pc29mxx series the information in this document is current as of september, 2007. the information is subject to change without notice. for actual design-in, refer to the latest publications of nec electronics data sheets or data books, etc., for the most up-to-date specifications of nec electronics products. not all products and/or types are available in every country. please check with an nec electronics sales representative for availability and additional information. no part of this document may be copied or reproduced in any form or by any means without the prior written consent of nec electronics. nec electronics assumes no responsibility for any errors that may appear in this document. nec electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of nec electronics products listed in this document or any other liability arising from the use of such products. no license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of nec electronics or others. descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. the incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. nec electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. while nec electronics endeavors to enhance the quality, reliability and safety of nec electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. to minimize risks of damage to property or injury (including death) to persons arising from defects in nec electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. nec electronics products are classified into the following three quality grades: "standard", "special" and "specific". the "specific" quality grade applies only to nec electronics products developed based on a customer- designated "quality assurance program" for a specific application. the recommended applications of an nec electronics product depend on its quality grade, as indicated below. customers must check the quality grade of each nec electronics product before using it in a particular application. the quality grade of nec e lectronics products is "standard" unless otherwise expressly specified in nec electronics data sheets or data books, etc. if customers wish to use nec electronics products in applications not intended by nec electronics, they must contact an nec electronics sales representative in advance to determine nec electronics' willingness to support a given application. (note) ? ? ? ? ? ? m8e 02. 11-1 (1) (2) "nec electronics" as used in this statement means nec electronics corporation and also includes its majority-owned subsidiaries. "nec electronics products" means any product developed or manufactured by or for nec electronics (as defined above). computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. " standard": " special": " specific":

▲Up To Search▲

Price & Availability of UPC29M07T-E2-AY

	To Download UPC29M07T-E2-AY Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .