patent no. 5600546 and 5652700 nlp150h series single, dual, triple and quad output [ 2 year warranty ] ?6.5 x 3.0 x 3.06 package (2u applications) ?smallest industry footprint ?en61000-3-2 compliant ?overvoltage and short circuit protection ?150w with 150lfm ?en55022, en55011 conducted emissions level b ?en61000-4-2, -3, -4, -5, -6 immunity compliant ?ul, vde and csa safety approvals the nlp150h series is a 150w universal input ac/dc power supply in a 6.5 x 3.0 x 3.06 inch package for use in 2u applications. the series has the smallest standard 125 to 150w footprint in the industry, has input harmonic current emission correction as standard and has 3.3v models to support the semiconductor industry's transition from 5v to lower operating voltages. the nlp150h provides 150w of output power with 150lfm of air. standard features include overvoltage and short circuit protection. the series has an enclosure with fan option that does not change the overall package size. the series, with full international safety approval and the ce mark, meets conducted emissions en55022 level b and complies to en61000-4-2,-3,-4, -5 and -6 immunity standards. the nlp150h series is designed for use in low power data networking, computer and telecom applications such as hubs, routers, file servers, graphic workstations, storage peripherals and pabx's. specification all specifications are typical at nominal input, full load at 25 c unless otherwise stated page 58 output specifications total regulation single outputs ?.0% (line and load) multiple outputs (5v, 3.3v) ?.0% auxiliary outputs ?.0% rise time at turn-on 250ms, max. transient response main output 5.0% or 250mv 25% step max. dev., 1ms max. at 0.1a/? recovery to 1% temperature coefficient ?.02%/? overvoltage protection single outputs and 125% of nominal multi outputs 1 and 2 ?0% tolerance short circuit protection continuous minimum output current yes, see table remote sense outputs 1 and 2 0.5v max. drop input specifications input voltage range universal input 90 to 264vac input frequency range 47hz to 63hz input surge current 120vac 19a max. (cold start) 230vac 38a max. safety ground 120vac, 60hz 0.7ma leakage current 230vac, 50hz 1.4ma input current 120vac 2.4a max. input fuse ul, iec approved 250vac 6.3a emc characteristics (7) conducted emissions en55022, fcc part 15 level b radiated emissions en55022, fcc part 15 level a esd air en61000-4-2, level 3 perf. criteria 1 esd contact en61000-4-2, level 4 perf. criteria 1 surge en61000-4-5, level 3 perf. criteria 1 fast transients en61000-4-4, level 3 perf. criteria 1 radiated immunity en61000-4-3, level 3 perf. criteria 1 conducted immunity en61000-4-6, level 3 perf. criteria 1 general specifications hold-up time 120vac, 60hz 16ms @ 150w efficiency 72% typical isolation voltage input/output 3000vac input/chassis 1500vac switching frequency fixed 100khz, ?0khz approvals and vde0805, en60950 standards iec950, ul1950 (see note 6) csa c22.2 no. 950 weight open-frame 680g (24 oz) with cover and fan 900g (31.77 oz) size open-frame 6.5 x 3.0 x 3.06 in. with cover and fan 7.5 x 3.0 x 3.10 in. mtbf mil-hdbk-217f > 200,000 hours environmental specifications thermal performance 0? to +50? ambient, 150w 150lfm forced air non-operating -40? to +85? +50? to +70?, derate to 150lfm forced air 50% load peak (0? to +50?, 60s) (see note 2) relative humidity non-condensing 5% to 95% rh altitude operating 10,000 feet max. non-operating 30,000 feet max. vibration (see note 4) 5hz to 500hz 2.4g rms peak shock per mil-std-810e 516.4 part iv
notes 1 150lfm forced air cooling (150w max.). 2 peak output current lasting less than 60 seconds with duty cycle less than 5%. during peak loading, output voltage may exceed total regulation limits. 3 figure is peak-to-peak. output noise measurements are made across a 20mhz bandwidth using a 12 inch twisted pair, terminated with a 47? capacitor. 4 three orthogonal axes, random vibration 10 minutes for each axes, 2.4g rms 5hz to 500hz. 5 caution: allow a minimum of 1 second after disconnecting line power when making thermal measurements. 6 this product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. 7 for system emi compliance, a ground choke may be required before connecting the ground wire to the chassis. 8 to order the nlp150h with an enclosure, add the suffix 'e' to the model number e.g. nlp150h-96xxe. see page 61 for details. 9 for single output models, j2 and j3 must be connected in parallel for proper operation. to maintain specified regulation on enclosed single output models and on v a and v b of enclosed multiple output models, the remote sense pins should be used. 10 for optimum reliability no part of the heatsink should exceed 120? and no semi-conductor case temperature should exceed 135?. international safety standard approvals vde0805/en60950/iec950 file no. 10401-3336-0108 licence no. 98724 ul1950 file no. e136005 csa c22.2 no. 950 file no. lr41062c 150w 75w 0 c 10 c 20 c 30 c 40 c 50 c 60 c 70 c derating curve output power (watts) 150 lfm forced air cooling output output current ripple (3) total model voltage min max (1) peak (2) regulation numbers (8,9) 5v 3a 30a 36a 50mv 2.0% nlp150h-9605 12v 1.25a 12.5a 15a 120mv 2.0% nlp150h-9612 13.8v 1.1a 11a 13a 120mv 2.0% nlp150h-9614 24v 0.63a 6.3a 7.5a 240mv 2.0% nlp150h-9624 48v 0.32a 3.2a 3.75a 480mv 2.0% nlp150h-9617 5v (v a ) 1.5a 15a 18a 50mv 2.0% nlp150h-9690 3.3v (v b ) 1.5a 15a 18a 50mv 2.0% 5v (v a ) 1.5a 15a 18a 50mv 2.0% nlp150h-9608 12v (v b ) 0.63a 6.3a 7.5a 120mv 2.0% 12v (v c ) 0a 0.8a 1.0a 120mv 5.0% 5v (v a ) 1.5a 15a 18a 50mv 2.0% nlp150h-9610 15v (v b ) 0.5a 5a 6a 150mv 2.0% 15v (v c ) 0a 0.8a 1.0a 150mv 5.0% 5v (v a ) 1.5a 15a 18a 50mv 2.0% nlp150h-9691 3.3v (v b ) 1.2a 12a 15a 50mv 2.0% 12v (v c ) 0a 1.25a 1.25a 120mv 5.0% -12v (v d ) 0a 0.8a 1.0a 120mv 5.0% 5v (v a ) 1.5a 15a 18a 50mv 2.0% nlp150h-9602 12v (v b ) 0.63a 6.3a 7.5a 120mv 2.0% 24v (v c ) 0a 0.8a 1.0a 240mv 5.0% -12v (v d ) 0a 0.8a 1.0a 120mv 5.0% 125 to 150 watt ac/dc universal input switch mode power supplies low to medium power ac/dc power supplies | 125- 150w ac/dc page 59 http://www.artesyn.com 1
3.000 (76.2) 6.085 (154.559) 6.50 (165.1) 2.300 (58.42) 1.750 (44.45) j1 ac input 0.35 (8.89) l n g va sense j12 power good j13 j2 va power j7 int fan power j6 vb sense j3 vb-d power 1.825 (46.355) 0.59 (14.99) pin # 1 typ. (? 0.19 (4.826) 0.94 (23.876) 5.625 (142.875) 0.35 (8.89) 0.138-32-unc-2b (10 places) (3 each side, 4 on bottom) 1/4" (6.35) max. thread penetration - typ. 5.175 (131.445) 5.500 (139.7) 1.775 (45.085) 0.45 (11.43) 6.085 (154.559) 0.37 ref. (9.398) 0.156 (4 places) (4.191) 2.275 (57.785) 0.19 (4.826) all dimensions in inches (mm) tolerances unless otherwise specified .xx = 0.02 .xxx = 0.010 third angle projection 3.00 (76.20) 3.06 (77.72) j1 ac input j7 j6 j3 j12 j13 j2 signal pin assignment (j6, j12, j13) three two-pin molex 6373 type connectors (p/n: 22-23-2021) with 0.100 inch spacing or equivalent are used for remote sensing and power good signal. the pin assignment is summarized in the following tables. pin numbering is from right to left facing the connector. input pin assignment (j1) (open-frame only) the input connector is a standard leoco 5-pin polarized header type connector with 0.156 inch spacing (3940p05v000) or equivalent. the recommended mating connector socket is the leoco 3940 series (3940s050000) or equivalent. the pin assignment is summarized below. pin numbering is from right to left facing the connector. output pin assignment (j2, j3) the output power connectors are two standard leoco 6-pin polarized header type connectors with 0.156 inch spacing (3940p06v000) or equivalent. the recommended mating connector sockets are the leoco 3940 series (3940s060000) or equivalents. the pin assignment is summarized below. pin numbering is from right to left facing the connector. for single output models, j2 and j3 must be connected in parallel for proper operation. input pin connections j1 pin 1 ground pin 2 no pin pin 3 neutral (ac low) pin 4 no pin pin 5 line (ac high) open-frame mechanical drawing page 60 125 to 150 watt ac/dc universal input switch mode power supplies 125-150w ac/dc | low to medium power ac/dc power supplies pin connections j2 (all models) pin 1 v a pin 2 v a pin 3 v a pin 4 return pin 5 return pin 6 return output pin connections j3 single (9) dual triple quad pin 1 v a v b v c v d pin 2 v a v b v b v b pin 3 v a v b v b v b pin 4 return return return return pin 5 return return return return pin 6 return return no pin v c pin connections j13 (all models) pin 1 v a return pin 2 power good pin connections j12 (all models) pin 1 - sense v a pin 2 + sense v a pin connections j6 (all models) pin 1 - sense v b pin 2 + sense v b
all dimensions in inches (mm) 5.175 (131.445) 5.500 (139.70) 2.275 (57.785) 2.300 (58.42) 2.80 (71.12) 0.35 (8.89) 7.50 (190.50) 6.05 (153.67) 5.625 (142.875) 0.22 (5.59) 0.41 (10.41) 0.138 (3.505) 32-unc-2b (10 places) (3 each side, 4 on bottom) 1/4" max. thread penetration -typ. 0.156 (3.96) (4 pls) 1.775 (45.09) 1.825 (46.36) 0.38 (9.65) 0.59 (14.99) 0.48 (12.19) 1.750 (44.45) output cable assembly p1 main output - 6 inches long p4-6 sig outputs - 8 inches long 3.10 (78.74) 2.57 (65.28) 3.00 (76.20) 0.63 (16.00) 6.50 (165.1) 1.50 (38.10) 60mm internal fan 2.09 (53.09) 2.000 (50.8) 0.50 (12.70) 0.691 (17.55) air flow third angle projection iec - 380 ac inlet 0.138 (3.505) 32-unc-2b (2 places) tolerances unless otherwise specified .xx = 0.02 .xxx = 0.010 0.94 (23.88) 0.14 (3.56) 14 7 8 1 p1 output power connector mating end of connector shown enclosed mechanical drawing signal pin assignment (p4, p5, p6) three two-pin molex mini-fit connectors (p/n: 39-01-4031) with 0.165 inch spacing or equivalent with molex crimp terminals (p/n: 39-00-0039) or equivalent. the pin assignment is summarized in the following tables. pin numbering is from right to left facing the connector. pin connections p4 (all models) pin 1 - sense v a pin 2 + sense v a pin 3 no connection pin connections p5 (all models) pin 1 v a return pin 2 no connection pin 3 power good pin connections p6 (all models) pin 1 no connection pin 2 - sense v b pin 3 + sense v b 1 3 p4 va sense 1 3 p5 power good 1 3 p6 vb sense output pin assignment (p1) molex mini-fit connector (p/n: 39-01-2145) or equivalent with molex crimp terminals (p/n: 39-00-0059) or equivalent. the pin assignment is summarized below. 125 to 150 watt ac/dc universal input switch mode power supplies low to medium power ac/dc power supplies | 125- 150w ac/dc page 61 http://www.artesyn.com output pin connections p1 single dual triple quad pin 1 return return return return pin 2 return return return return pin 3 return return return return pin 4 v a v b v b v b pin 5 v a v b v b v b pin 6 v a v b v b v b pin 7 v a v b v c v d pin 8 return return no connect. v c pin 9 return return return return pin 10 return return return return pin 11 return return return return pin 12 v a v a v a v a pin 13 v a v a v a v a pin 14 v a v a v a v a data sheet ?artesyn technologies 2000 the information and specifications contained in this data sheet are believed to be correct at time of publication. however, ar tesyn technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. specifications are subject to change without notice. no rights under any patent accompa ny the sale of any such product(s) or information contained herein. 1 ds_nlp150h_20000918pdf
|
