? semiconductor components industries, llc, 2006 october, 2006 ? rev. 8 1 publication order number: mc74ac05/d mc74ac05, mc74act05 hex inverter with open?drain outputs the mc74ac/act05 is identical in pinout to the ls05. the device inputs are compatible with standard cmos outputs; with pullup resistors, they are compatible with ttl outputs. features ? outputs source/sink 24 ma ? act05 has ttl compatible inputs ? pb ? free packages are available gnd figure 1. pinout: 14-lead packages 13 14 12 11 10 9 8 2 134 567 v cc a 6 y 6 a 5 y 5 a 4 y 4 a 1 y 1 a 2 y 2 a 3 y 3 top view figure 2. logic diagram y* 2, 4, 6, 8, 10, 12 1, 3, 5, 9, 11, 13 a pin 14 = vcc pin 7 = gnd * denotes open-drain outputs 1 see general marking information in the device marking section on page 6 of this data sheet. device marking information http://onsemi.com see detailed ordering and shipping information in the package dimensions sec tion on page 5 of this data sheet. ordering information tssop ? 14 dt suffix case 948g 1 soeiaj ? 14 m suffix case 965 soic ? 14 d suffix case 751a 1 1 pdip ? 14 n suffix case 646 function table input a l h output y z l note: z = high impedance
mc74ac05, mc74act05 http://onsemi.com 2 maximum ratings symbol parameter value unit v cc dc supply voltage (referenced to gnd) ? 0.5 to +7.0 v v in dc input voltage (referenced to gnd) ? 0.5 to v cc + 0.5 v v out dc output voltage (referenced to gnd) ? 0.5 to v cc + 0.5 v i in dc input current, per pin 20 ma i out dc output sink/source current, per pin 50 ma i cc dc v cc or gnd current per output pin 50 ma t stg storage temperature ? 65 to +150 c stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability. recommended operating conditions symbol parameter min typ min unit v cc supply voltage ac 2.0 5.0 6.0 v act 4.5 5.0 5.5 vreg dc regulated power voltage (ref. to gnd) 0 ? v cc v t r , t f input rise and fall time (note 1) ac devices except schmitt inputs v cc @ 3.0 v ? 150 ? v cc @ 4.5 v ? 40 ? ns/v v cc @ 5.5 v ? 25 ? t r , t f input rise and fall time (note 2) act devices except schmitt inputs v cc @ 4.5 v ? 10 ? ns/v v cc @ 5.5 v ? 8.0 ? t j junction temperature (pdip) ? ? 140 c t a operating ambient temperature range ? 40 25 85 c i oh output current ? high ? ? ? 24 ma i ol output current ? low ? ? 24 ma 1. v in from 30% to 70% v cc ; see individual data sheets for devices that differ from the typical input rise and fall times. 2. v in from 0.8 v to 2.0 v; see individual data sheets for devices that differ from the typical input rise and fall times.
mc74ac05, mc74act05 http://onsemi.com 3 dc characteristics symbol parameter v cc (v) 74ac 74ac unit conditions t a = +25 c t a = ? 40 c to +85 c typ guaranteed limits v ih minimum high level input voltage 3.0 1.5 2.1 2.1 v out = 0.1 v 4.5 2.25 3.15 3.15 v or v cc ? 0.1 v 5.5 2.75 3.85 3.85 v il maximum low level input voltage 3.0 1.5 0.9 0.9 v out = 0.1 v 4.5 2.25 1.35 1.35 v or v cc ? 0.1 v 5.5 2.75 1.65 1.65 v ol maximum low level output voltage 3.0 0.002 0.1 0.1 i out = 50 a 4.5 0.001 0.1 0.1 v 5.5 0.001 0.1 0.1 v *v in = v il or v ih 3.0 ? 0.36 0.44 12 ma 4.5 ? 0.36 0.44 i ol 24 ma 5.5 ? 0.36 0.44 24 ma i in maximum input leakage current 5.5 ? 0.1 1.0 a v i = v cc , gnd i old ?minimum dynamic output current 5.5 ? ? 75 ma v old = 1.65 v max i ohd 5.5 ? ? ? 75 ma v ohd = 3.85 v min i cc maximum quiescent supply current 5.5 ? 4.0 40 a v in = v cc or gnd *all outputs loaded; thresholds on input associated with output under test. ?maximum test duration 2.0 ms, one output loaded at a time. note: i in and i cc @ 3.0 v are guaranteed to be less than or equal to the respective limit @ 5.5 v. ac characteristics symbol parameter v cc * (v) 74ac 74ac unit t a = +25 c c l = 50 pf t a = ? 40 c to +85 c c l = 50 pf min typ max min max t pzl propagation delay output enable 3.3 1.5 ? 8.0 1.0 9.0 ns 5.0 1.5 ? 6.0 1.0 6.5 t plz propagation delay output enable 3.3 1.5 ? 8.0 1.0 9.0 ns 5.0 1.5 ? 6.0 1.0 6.5 *voltage range 3.3 v is 3.3 v 0.3 v. voltage range 5.0 v is 5.0 v 0.5 v.
mc74ac05, mc74act05 http://onsemi.com 4 dc characteristics symbol parameter v cc (v) 74act 74act unit conditions t a = +25 c t a = ? 40 c to +85 c typ guaranteed limits v ih minimum high level input voltage 4.5 5.5 1.5 1.5 2.0 2.0 2.0 2.0 v v out = 0.1 v or v cc ? 0.1 v v il maximum low level input voltage 4.5 5.5 1.5 1.5 0.8 0.8 0.8 0.8 v v out = 0.1 v or v cc ? 0.1 v v ol maximum low level output voltage 4.5 5.5 0.001 0.001 0.1 0.1 0.1 0.1 v i out = 50 a 4.5 5.5 ? ? 0.36 0.36 0.44 0.44 0.44 *v in = v il or v ih i oh 24 ma i in maximum input leakage current 5.5 ? 0.1 1.0 a v i = v cc , gnd i cct additional max. i cc /input 5.5 0.6 ? 1.5 ma v i = v cc ? 2.1 v i old i ohd ?minimum dynamic output current 5.5 5.5 ? ? ? ? 75 ? 75 ma ma v old = 1.65 v max v ohd = 3.85 v min i cc maximum quiescent supply current 5.5 ? 4.0 40 a v in = v cc or gnd *all outputs loaded; thresholds on input associated with output under test. ?maximum test duration 2.0 ms, one output loaded at a time. ac characteristics symbol parameter v cc * (v) 74act 74act unit t a = +25 c c l = 50 pf t a = ? 40 c to +85 c c l = 50 pf min typ max min max t pzl propagation delay output enable 5.0 1.5 ? 8.0 1.0 8.5 ns t plz propagation delay output enable 5.0 1.5 ? 8.5 1.0 9.0 ns *voltage range 5.0 v is 5.0 v 0.5 v. capacitance symbol parameter value typ unit test conditions c in input capacitance 4.5 pf v cc = 5.0 v c pd power dissipation capacitance 30 pf v cc = 5.0 v
mc74ac05, mc74act05 http://onsemi.com 5 ordering information device package shipping ? mc74ac05n pdip ? 14 25 units / rail mc74ac05ng pdip ? 14 (pb ? free) mc74ac05d soic ? 14 55 units / rail mc74ac05dg soic ? 14 (pb ? free) mc74ac05dr2 soic ? 14 2500 / tape & reel mc74ac05dr2g soic ? 14 (pb ? free) mc74ac05mel soeiaj ? 14 2000 / tape & reel mc74ac05melg soeiaj ? 14 (pb ? free) mc74act05n pdip ? 14 25 units / rail mc74act05ng pdip ? 14 (pb ? free) mc74act05d soic ? 14 55 units / rail mc74act05dg soic ? 14 (pb ? free) mc74act05dr2 soic ? 14 2500 / tape & reel MC74ACT05DR2G soic ? 14 (pb ? free) mc74act05dtr2 tssop ? 14* mc74act05dtr2g tssop ? 14* mc74act05mel soeiaj ? 14 2000 / tape & reel mc74act05melg soeiaj ? 14 (pb ? free) ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d. *these packages are inherently pb ? free.
mc74ac05, mc74act05 http://onsemi.com 6 marking diagrams pdip ? 14 soic ? 14 tssop ? 14 soeiaj ? 14 1 14 74act05 alywg ac05g awlyww 1 14 act 05 alyw 1 14 a = assembly location wl, l = wafer lot yy, y = year ww, w = work week g or = pb ? free package (note: microdot may be in either location) act05g awlyww 1 14 1 14 74ac05 alywg mc74ac05n awlyywwg 1 14 mc74act05n awlyywwg 1 14
mc74ac05, mc74act05 http://onsemi.com 7 package dimensions pdip ? 14 case 646 ? 06 issue p 17 14 8 b a dim min max min max millimeters inches a 0.715 0.770 18.16 19.56 b 0.240 0.260 6.10 6.60 c 0.145 0.185 3.69 4.69 d 0.015 0.021 0.38 0.53 f 0.040 0.070 1.02 1.78 g 0.100 bsc 2.54 bsc h 0.052 0.095 1.32 2.41 j 0.008 0.015 0.20 0.38 k 0.115 0.135 2.92 3.43 l m ??? 10 ??? 10 n 0.015 0.039 0.38 1.01 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. dimension l to center of leads when formed parallel. 4. dimension b does not include mold flash. 5. rounded corners optional. f hg d k c seating plane n ? t ? 14 pl m 0.13 (0.005) l m j 0.290 0.310 7.37 7.87
mc74ac05, mc74act05 http://onsemi.com 8 package dimensions soic ? 14 case 751a ? 03 issue h notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. ? a ? ? b ? g p 7 pl 14 8 7 1 m 0.25 (0.010) b m s b m 0.25 (0.010) a s t ? t ? f r x 45 seating plane d 14 pl k c j m dim min max min max inches millimeters a 8.55 8.75 0.337 0.344 b 3.80 4.00 0.150 0.157 c 1.35 1.75 0.054 0.068 d 0.35 0.49 0.014 0.019 f 0.40 1.25 0.016 0.049 g 1.27 bsc 0.050 bsc j 0.19 0.25 0.008 0.009 k 0.10 0.25 0.004 0.009 m 0 7 0 7 p 5.80 6.20 0.228 0.244 r 0.25 0.50 0.010 0.019 7.04 14x 0.58 14x 1.52 1.27 dimensions: millimeters 1 pitch soldering footprint* 7x *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d.
mc74ac05, mc74act05 http://onsemi.com 9 package dimensions tssop ? 14 case 948g ? 01 issue a dim min max min max inches millimeters a 4.90 5.10 0.193 0.200 b 4.30 4.50 0.169 0.177 c ??? 1.20 ??? 0.047 d 0.05 0.15 0.002 0.006 f 0.50 0.75 0.020 0.030 g 0.65 bsc 0.026 bsc h 0.50 0.60 0.020 0.024 j 0.09 0.20 0.004 0.008 j1 0.09 0.16 0.004 0.006 k 0.19 0.30 0.007 0.012 k1 0.19 0.25 0.007 0.010 l 6.40 bsc 0.252 bsc m 0 8 0 8 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimension a does not include mold flash, protrusions or gate burrs. mold flash or gate burrs shall not exceed 0.15 (0.006) per side. 4. dimension b does not include interlead flash or protrusion. interlead flash or protrusion shall not exceed 0.25 (0.010) per side. 5. dimension k does not include dambar protrusion. allowable dambar protrusion shall be 0.08 (0.003) total in excess of the k dimension at maximum material condition. 6. terminal numbers are shown for reference only. 7. dimension a and b are to be determined at datum plane ? w ? . s u 0.15 (0.006) t 2x l/2 s u m 0.10 (0.004) v s t l ? u ? seating plane 0.10 (0.004) ? t ? ??? ??? ??? section n ? n detail e j j1 k k1 ? w ? 0.25 (0.010) 8 14 7 1 pin 1 ident. h g a d c b s u 0.15 (0.006) t ? v ? 14x ref k n n
mc74ac05, mc74act05 http://onsemi.com 10 package dimensions soeiaj ? 14 case 965 ? 01 issue a h e a 1 dim min max min max inches ??? 2.05 ??? 0.081 millimeters 0.05 0.20 0.002 0.008 0.35 0.50 0.014 0.020 0.10 0.20 0.004 0.008 9.90 10.50 0.390 0.413 5.10 5.45 0.201 0.215 1.27 bsc 0.050 bsc 7.40 8.20 0.291 0.323 0.50 0.85 0.020 0.033 1.10 1.50 0.043 0.059 0 0.70 0.90 0.028 0.035 ??? 1.42 ??? 0.056 a 1 h e q 1 l e 10 0 10 l e q 1 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions d and e do not include mold flash or protrusions and are measured at the parting line. mold flash or protrusions shall not exceed 0.15 (0.006) per side. 4. terminal numbers are shown for reference only. 5. the lead width dimension (b) does not include dambar protrusion. allowable dambar protrusion shall be 0.08 (0.003) total in excess of the lead width dimension at maximum material condition. dambar cannot be located on the lower radius or the foot. minimum space between protrusions and adjacent lead to be 0.46 ( 0.018). 0.13 (0.005) m 0.10 (0.004) d z e 1 14 8 7 e a b view p c l detail p m a b c d e e 0.50 m z on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5773 ? 3850 mc74ac05/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative
|
