View R3130N29EA3-TR_6780099.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

12345 low voltage detector with built-in delay circuit r3130nxxxa/c,r3131nxxxa/c 2000.5.26 12345 rev. 1.10 1 n outline r3130n/r3131n series are low voltage detector ics with built-in delay circuit, high detector threshold accuracy and ultra low supply current by cmos process, which can be operated at low voltage. these ics can be used as system reset generator, and each of these ics consists of a voltage reference, a comparator, resistors for setting voltage detector threshold, an output driver transistor, and an output delay generator. detector threshold is fixed internally with high accuracy and requires no adjustment. when supply voltage crosses a setting detector threshold voltage from a high value to a lower value, this ic generates reset signal. r3130n series output "l" at detection mode, while r3131n series output "h". further, each of r3130n/r3131n series embeds an output delay generator, when supply voltage crosses a setting detector threshold voltage from a low value to a higher value, during a setting delay time which is fixed in the ic, this ic keeps the reset condition. output delay time can be selected. (typ. 240ms is standard.) two output types, nch open drain type and cmos type, are available. since the package for these ics are sot23-3 (mini-mold) package, high density mounting of the ics on board is possible. n n n n features l pin to pin compatible with max809/810 (r3130nxxxx: max809, r3131nxxxx: max810) l ultra-low supply current typ. 1.25a (r313xn27xx: v dd =3.0v) l operating voltage range 1.0v to 6.0v (topt=25 c) l detector threshold s etting with a step of 0.1v in the range of 1.6v to 4.8v is possible. l embedded power on reset delay time circuit delay time can be designated. refer to selection guide. l high accuracy detector threshold 1.5% l high accuracy output delay time 10.0% l low temperature-drift coefficient of detector threshold typ. 100ppm/ c l two output types nch open drain and cmos l small package sot-23-3 n n n n applications l cpu & logic circuit reset l battery checker l window comparator l wave shaping circuit l battery back-up circuit l power failure detector n n n n block diagrams l nch open drain output l cmos output vref delay circuit vdd gnd vref delay circuit vdd gnd out out
12345 rev. 1.10 2 n n n n timing chart detector threshold vdet vss supply volt age (vdd) output voltage vss t delay minimum operating voltage detector threshold vdet vss supply voltage (vdd) output voltage vss t delay minimum operating voltage r3130n operation diagram r3131n operation diagram l output delay operation output delay time, or tdelay is specified as follows: 1. in the case of nch open drain output: the time interval from rising edge of v dd pulse (1.0v ? (v det )+0.1v) to the time at which the output reaches 2.5v under the condition that the output pin(out) is pulled up to 5v through a 470k w resistor. 2. in the case of cmos output the time interval from rising edge of v dd pulse (1.0v ? (v det )+0.1v) to the time at which the output reaches v dd /2. tdela y trst input voltage (v dd ) output voltage +v det +1.0v 1.0v gnd gnd 5.0v 2.5v tdela y trst input voltage (v dd ) output voltage +v det +1.0v 1.0v gnd gnd +v det +0.1v +v det +0.1v 2 cmos output nch open drain output vdet+0.1v vdet+0.1v 1.5v 1.5v trst tdelay trst tdelay vdet+0.1v (vdet+0.1v)/2
12345 rev. 1.10 3 n selection guide the detector threshold , the output type, and output delay time of r3130n series can be designated at the users request by specifying the part number as follows: r3130n 5555 5 -tr ? part number r3131n 5555 5 -tr ? part number - - - - - a b c d e code contents a setting detector threshold(v det ) stepwise setting with a step of 0.1v in the range of 1.6v to 4.8v is possible. the following 6 kinds of voltage are also standard. 2.63v, 2.93v, 3.08v, 4.00v, 4.40v, 4.65v b selection of output delay time e:240ms(standard) a:50ms b:100ms d: 200ms h:400ms *a, b, d, h versions can be produced only for 6 kinds of standard voltage items. c designation output type a: nch open drain c: cmos d description of last one digit of 6 kinds of standard voltage items. e designation of taping direction (refer to taping specification) n pin configuration l sot-23-3 mark side 1 2 3
12345 rev. 1.10 4 n pin description pin no. symbol description 1 gnd ground pin 2 out output pin r3130n: output l at detection mode, output h at release mode r3131n: output h at detection mode, output l at release mode 3v dd input pin n absolute maximum ratings symbol item rating unit v dd supply voltage 6.5 v cmos v ss -0.3 to v dd +0.3 v v out output voltage nch v ss -0.3 to 6.5 v i out output current 20 ma p d power dissipation 150 mw topt operating temperature range -40 to +85 c tstg storage temperature range -55 to +125 c tsolder soldering temperature 260 c, 10s absolute maximum ratings absolute maximum ratings are threshold limit values that must not be exceeded even for a moment under any conditions. moreover, such values for any items must not be reached simultaneously. operation above these absolute maximum ratings may cause degradation or permanent damage to the device. these are just stress ratings and do not necessarily imply to guarantee operation below these limits.
12345 rev. 1.10 5 n electrical characteristics r3130n26xx3-tr [t opt =25 c] symbol item test conditions min. typ. max. unit v ddh maximum operating voltage 6.0 v v ddl(*1) minimum operating voltage i ol =50 m a 0.75 1.00 v v det detector threshold 2.591 2.630 2.669 v i ss 1 supply current1 v dd= 6.00v 1.40 5.00 m a i ss 2 supply current2 v dd= 2.73v 1.25 4.00 m a i ss 3 supply current3 v dd= 2.53v 1.10 3.50 m a v oh h output voltage v dd =2.73v, i out =-500 m a0.8 v dd 0.93 v dd v v ol l output voltage v dd =2.53v, i out =1.2ma 0.16 0.30 v tdelay(*2) output delay time for release refer to electrical characteristics by output delay time for release d v det / d topt detector threshold temperature coefficient -40 c topt 85 c 100 ppm/ c r3130n29xx3-tr [t opt =25 c] symbol item test conditions min. typ. max. unit v ddh maximum operating voltage 6.0 v v ddl(*1) minimum operating voltage i ol =50 m a 0.75 1.00 v v det detector threshold 2.887 2.930 2.973 v i ss 1 supply current1 v dd= 6.00v 1.40 5.00 m a i ss 2 supply current2 v dd =3.03v 1.25 4.00 m a i ss 3 supply current3 v dd= 2.83v 1.10 3.50 m a v oh h output voltage v dd =3.03v, i out =-500 m a0.8 v dd 0.93 v dd v v ol l output voltage v dd =2.83v, i out =1.2ma 0.16 0.30 v tdelay(*2) output delay time for release refer to electrical characteristics by output delay time for release d v det / d topt detector threshold temperature coefficient -40 c topt 85 c 100 ppm/ c
12345 rev. 1.10 6 r3130n30xx8-tr [t opt =25 c] symbol item test conditions min. typ. max. unit v ddh maximum operating voltage 6.0 v v ddl(*1) minimum operating voltage i ol =50 m a 0.75 1.00 v v det detector threshold 3.034 3.080 3.126 v i ss 1 supply current1 v dd= 6.00v 1.40 5.00 m a i ss 2 supply current2 v dd =3.18v 1.25 4.00 m a i ss 3 supply current3 v dd= 2.98v 1.10 3.50 m a v oh h output voltage v dd =3.18v, i out =-500 m a0.8 v dd 0.93 v dd v v ol l output voltage v dd =2.98v, i out =1.2ma 0.16 0.30 v tdelay(*2) output delay time for release refer to electrical characteristics by output delay time for release d v det / d topt detector threshold temperature coefficient -40 c topt 85 c 100 ppm/ c r3130n40xx-tr [t opt =25 c] symbol item test conditions min. typ. max. unit v ddh maximum operating voltage 6.0 v v ddl(*1) minimum operating voltage i ol =50 m a 0.75 1.00 v v det detector threshold 3.940 4.000 4.060 v i ss 1 supply current1 v dd= 6.00v 1.40 5.00 m a i ss 2 supply current2 v dd =4.10v 1.30 4.00 m a i ss 3 supply current3 v dd =3.90v 1.15 3.50 m a v oh h output voltage v dd =4.10v, i out =-800 m a0.8 v dd 0.95 v dd v v ol l output voltage v dd =3.90v, i out =3.2ma 0.18 0.40 v tdelay(*2) output delay time for release refer to electrical characteristics by output delay time for release d v det / d topt detector threshold temperature coefficient -40 c topt 85 c 100 ppm/ c
12345 rev. 1.10 7 r3130n44xx-tr [t opt =25 c] symbol item test conditions min. typ. max. unit v ddh maximum operating voltage 6.0 v v ddl(*1) minimum operating voltage i ol =50 m a 0.75 1.00 v v det detector threshold 4.334 4.400 4.466 v i ss 1 supply current1 v dd= 6.00v 1.40 5.00 m a i ss 2 supply current2 v dd =4.50v 1.30 4.00 m a i ss 3 supply current3 v dd =4.30v 1.15 3.50 m a v oh h output voltage v dd =4.50v, i out =-800 m a0.8 v dd 0.95 v dd v v ol l output voltage v dd =4.30v, i out =3.2ma 0.18 0.40 v tdelay(*2) output delay time for release refer to electrical characteristics by output delay time for release d v det / d topt detector threshold temperature coefficient -40 c topt 85 c 100 ppm/ c r3130n46xx5-tr [t opt =25 c] symbol item test conditions min. typ. max. unit v ddh maximum operating voltage 6.0 v v ddl(*1) minimum operating voltage i ol =50 m a 0.75 1.00 v v det detector threshold 4.581 4.650 4.719 v i ss 1 supply current1 v dd= 6.00v 1.40 5.00 m a i ss 2 supply current2 v dd =4.75v 1.30 4.00 m a i ss 3 supply current3 v dd =4.55v 1.15 3.50 m a v oh h output voltage v dd =4.75v, i out =-800 m a0.8 v dd 0.95 v dd v v ol l output voltage v dd =4.55v, i out =3.2ma 0.18 0.40 v tdelay(*2) output delay time for release refer to electrical characteristics by output delay time for release d v det / d topt detector threshold temperature coefficient -40 c topt 85 c 100 ppm/ c
12345 rev. 1.10 8 r3131n26xx3-tr [t opt =25 c] symbol item test conditions min. typ. max. unit v ddh maximum operating voltage 6.0 v cmos output i oh =-10 m a v ddl(*3) minimum operating voltage nch open drain output v ds =6.5v 0.90 1.00 v v det detector threshold 2.591 2.630 2.669 v i ss 1 supply current1 v dd= 6.00v 1.40 5.00 m a i ss 2 supply current2 v dd= 2.73v 1.25 4.00 m a i ss 3 supply current3 v dd= 2.53v 1.10 3.50 m a v oh h output voltage v dd =2.73v, i out =-500 m a0.8 v dd 0.93 v dd v v ol l output voltage v dd =2.53v, i out =1.2ma 0.16 0.30 v tdelay(*2) output delay time for release refer to electrical characteristics by output delay time for release d v det / d topt detector threshold temperature coefficient -40 c topt 85 c 100 ppm/ c r3131n29xx3-tr [t opt =25 c] symbol item test conditions min. typ. max. unit v ddh maximum operating voltage 6.0 v cmos output i oh =-10 m a v ddl(*3) minimum operating voltage nch open drain output v ds =6.5v 0.90 1.00 v v det detector threshold 2.887 2.930 2.973 v i ss 1 supply current1 v dd= 6.00v 1.40 5.00 m a i ss 2 supply current2 v dd =3.03v 1.25 4.00 m a i ss 3 supply current3 v dd= 2.83v 1.10 3.50 m a v oh h output voltage v dd =2.83v, i out =-500 m a0.8 v dd 0.93 v dd v v ol l output voltage v dd =3.03v, i out =1.2ma 0.16 0.30 v tdelay(*2) output delay time for release refer to electrical characteristics by output delay time for release d v det / d topt detector threshold temperature coefficient -40 c topt 85 c 100 ppm/ c
12345 rev. 1.10 9 r3131n30xx8-tr [t opt =25 c] symbol item test conditions min. typ. max. unit v ddh maximum operating voltage 6.0 v cmos output i oh =-10 m a v ddl(*3) minimum operating voltage nch open drain output v ds =6.5v 0.90 1.00 v v det detector threshold 3.034 3.080 3.126 v i ss 1 supply current1 v dd= 6.00v 1.40 5.00 m a i ss 2 supply current2 v dd =3.18v 1.25 4.00 m a i ss 3 supply current3 v dd= 2.98v 1.10 3.50 m a v oh h output voltage v dd =2.98v, i out =-500 m a0.8 v dd 0.93 v dd v v ol l output voltage v dd =3.18v, i out =1.2ma 0.16 0.30 v tdelay(*2) output delay time for release refer to electrical characteristics by output delay time for release d v det / d topt detector threshold temperature coefficient -40 c topt 85 c 100 ppm/ c r3131n40xx-tr [t opt =25 c] symbol item test conditions min. typ. max. unit v ddh maximum operating voltage 6.0 v cmos output i oh =-10 m a v ddl(*3) minimum operating voltage nch open drain output v ds =6.5v 0.90 1.00 v v det detector threshold 3.940 4.000 4.060 v i ss 1 supply current1 v dd= 6.00v 1.40 5.00 m a i ss 2 supply current2 v dd =3.90v 1.30 4.00 m a i ss 3 supply current3 v dd =4.10v 1.15 3.50 m a v oh h output voltage v dd =3.90v, i out =-800 m a0.8 v dd 0.95 v dd v v ol l output voltage v dd =4.10v, i out =3.2ma 0.18 0.40 v tdelay(*2) output delay time for release refer to electrical characteristics by output delay time for release d v det / d topt detector threshold temperature coefficient -40 c topt 85 c 100 ppm/ c
12345 rev. 1.10 10 r3131n44xx-tr [t opt =25 c ] symbol item test conditions min. typ. max. unit v ddh maximum operating voltage 6.0 v cmos output i oh =-10 m a v ddl(*3) minimum operating voltage nch open drain output v ds =6.5v 0.90 1.00 v v det detector threshold 4.334 4.400 4.466 v i ss 1 supply current1 v dd= 6.00v 1.40 5.00 m a i ss 2 supply current2 v dd =4.50v 1.30 4.00 m a i ss 3 supply current3 v dd =4.30v 1.15 3.50 m a v oh h output voltage v dd =4.30v, i out =-800 m a0.8 v dd 0.95 v dd v v ol l output voltage v dd =4.50v, i out =3.2ma 0.18 0.40 v tdelay(*2) output delay time for release refer to electrical characteristics by output delay time for release d v det / d topt detector threshold temperature coefficient -40 c topt 85 c 100 ppm/ c r3131n46xx5-tr [t opt =25 c symbol item test conditions min. typ. max. unit v ddh maximum operating voltage 6.0 v cmos output i oh =-10 m a v ddl(*3) minimum operating voltage nch open drain output v ds =6.5v 0.90 1.00 v v det detector threshold 4.581 4.650 4.719 v i ss 1 supply current1 v dd= 6.00v 1.40 5.00 m a i ss 2 supply current2 v dd =4.75v 1.30 4.00 m a i ss 3 supply current3 v dd =4.55v 1.15 3.50 m a v oh h output voltage v dd =4.55v, i out =-800 m a0.8 v dd 0.95 v dd v v ol l output voltage v dd =4.75v, i out =3.2ma 0.18 0.40 v tdelay(*2) output delay time for release refer to electrical characteristics by output delay time for release d v det / d topt detector threshold temperature coefficient -40 c topt 85 c 100 ppm/ c *1) supply voltage when output voltage becomes equal or less than 0.3v. ( as for nch open drain output type, pull-up resistor is 470k w , pull-up voltage is 5.0v. *2) time interval of rising edge of v dd which is set from 1.0v to v det +1.0v, and the point of which output voltage reaches to 50% of final voltage. *3) cmos output type; supply voltage when output voltage becomes equal or more than 0.8 v dd. nch open drain type; supply voltage when off leakage current becomes equal or less than 0.1 m a.
12345 rev. 1.10 11 n electrical characteristics by output delay time [topt=25 c] output delay time (tdelay) part number test condition min. typ. max. unit r313xnxxax 45 50 55 r313xnxxbx 90 100 110 r313xnxxdx 180 200 220 r313xnxxex 216 240 264 r313xnxxhx v dd=1.0v to v det+1.0v 360 400 440 ms n electrical characteristics by detector threshold l r3130n16ea/c to r3130n48ea/c detector threshold supply current 1 supply current 2 supply current 3 v det( v) i ss1( m a) i ss2( m a) i ss3( m a) part number min. typ. max. condition typ. max. condition typ. max. condition typ. max. r3130n16ea/c 1.576 1.600 1.624 r3130n17ea/c 1.675 1.700 1.725 r3130n18ea/c 1.773 1.800 1.827 r3130n19ea/c 1.872 1.900 1.928 r3130n20ea/c 1.970 2.000 2.030 r3130n21ea/c 2.069 2.100 2.131 r3130n22ea/c 2.167 2.200 2.233 r3130n23ea/c 2.266 2.300 2.334 1.20 1.00 r3130n24ea/c 2.364 2.400 2.436 r3130n25ea/c 2.463 2.500 2.537 r3130n26ea/c 2.561 2.600 2.639 r3130n27ea/c 2.660 2.700 2.740 r3130n28ea/c 2.758 2.800 2.842 r3130n29ea/c 2.857 2.900 2.943 r3130n30ea/c 2.955 3.000 3.045 r3130n31ea/c 3.054 3.100 3.146 r3130n32ea/c 3.152 3.200 3.248 r3130n33ea/c 3.251 3.300 3.349 r3130n34ea/c 3.349 3.400 3.451 r3130n35ea/c 3.448 3.500 3.552 1.25 1.10 r3130n36ea/c 3.546 3.600 3.654 r3130n37ea/c 3.645 3.700 3.755 r3130n38ea/c 3.743 3.800 3.857 r3130n39ea/c 3.842 3.900 3.958 r3130n40ea/c 3.940 4.000 4.060 r3130n41ea/c 4.039 4.100 4.161 r3130n42ea/c 4.137 4.200 4.263 r3130n43ea/c 4.236 4.300 4.364 r3130n44ea/c 4.334 4.400 4.466 r3130n45ea/c 4.433 4.500 4.567 r3130n46ea/c 4.531 4.600 4.669 r3130n47ea/c 4.630 4.700 4.770 r3130n48ea/c 4.728 4.800 4.872 v dd= 6.0v 1.40 5.00 v dd= v det +0.1v 1.30 4.00 v dd= v det -0.1v 1.15 3.50
12345 rev. 1.10 12 topt=25 c h output voltage l output voltage minimum operating voltage output delay time detector threshold temperature coefficient v oh(v) v ol( v) v ddl(v) tdelay (ms) d v det/ d topt(ppm/ c) conditions min. typ. conditions typ. max. typ. max. min. typ. max . condition typ. v dd= v det +0.1v i oh= -150 m a 0.80 v dd 0.95 v dd v dd= v det +0.1v i oh= -500 m a 0.80 v dd 0.93 v dd v dd = v det -0.1v, i ol =1.2ma 0.16 0.30 v dd= v det +0.1v i oh= -800 m a 0.80 v dd 0.95 v dd v dd = v det -0.1v, i ol =3.2ma 0.18 0.40 *1 0.75 *1 1.00 216 240 264 -40 c topt 85 c 100 *1 describes v dd voltage when output voltage becomes equal or less than 0.3v.
12345 rev. 1.10 13 l r3131n16ea/c to r3131n48ea/c detector threshold supply current 1 supply current 2 supply current 3 v det( v) i ss1( m a) i ss2( m a) i ss3( m a) part number min. typ. max. condition typ. max. condition typ. max. condition typ. max. r3131n16ea/c 1.576 1.600 1.624 r3131n17ea/c 1.675 1.700 1.725 r3131n18ea/c 1.773 1.800 1.827 r3131n19ea/c 1.872 1.900 1.928 r3131n20ea/c 1.970 2.000 2.030 r3131n21ea/c 2.069 2.100 2.131 r3131n22ea/c 2.167 2.200 2.233 r3131n23ea/c 2.266 2.300 2.334 1.20 1.00 r3131n24ea/c 2.364 2.400 2.436 r3131n25ea/c 2.463 2.500 2.537 r3131n26ea/c 2.561 2.600 2.639 r3131n27ea/c 2.660 2.700 2.740 r3131n28ea/c 2.758 2.800 2.842 r3131n29ea/c 2.857 2.900 2.943 r3131n30ea/c 2.955 3.000 3.045 r3131n31ea/c 3.054 3.100 3.146 r3131n32ea/c 3.152 3.200 3.248 r3131n33ea/c 3.251 3.300 3.349 r3131n34ea/c 3.349 3.400 3.451 r3131n35ea/c 3.448 3.500 3.552 1.25 1.10 r3131n36ea/c 3.546 3.600 3.654 r3131n37ea/c 3.645 3.700 3.755 r3131n38ea/c 3.743 3.800 3.857 r3131n39ea/c 3.842 3.900 3.958 r3131n40ea/c 3.940 4.000 4.060 r3131n41ea/c 4.039 4.100 4.161 r3131n42ea/c 4.137 4.200 4.263 r3131n43ea/c 4.236 4.300 4.364 r3131n44ea/c 4.334 4.400 4.466 r3131n45ea/c 4.433 4.500 4.567 r3131n46ea/c 4.531 4.600 4.669 r3131n47ea/c 4.630 4.700 4.770 r3131n48ea/c 4.728 4.800 4.872 v dd= 6.0v 1.40 5.00 v dd= v det +0.1v 1.30 4.00 v dd= v det -0.1v 1.15 3.50
12345 rev. 1.10 14 topt=25 c h output voltage l output voltage minimum operating voltage output delay time detector threshold temperature coefficient v oh(v) v ol( v) v ddl(v) tdelay (ms) d v det/ d topt(ppm/ c) conditions min. typ. conditions typ. max. typ. max. min. typ. max . condition typ. v dd= v det -0.1v i oh= -150 m a 0.80 v dd 0.95 v dd v dd= v det -0.1v i oh= -500 m a 0.80 v dd 0.93 v dd v dd = v det +0.1v, i ol =1.2ma 0.16 0.30 v dd= v det -0.1v i oh= -800 m a 0.80 v dd 0.95 v dd v dd = v det +0.1v, i ol =3.2ma 0.18 0.40 *2 0.90 *2 1.00 216 240 264 -40 c topt 85 c 100 *2 cmos output type; describes v dd voltage when output voltage becomes equal or more than v dd 0.8v nch open drain output type; describes vdd voltage when off-leakage current becomes equal or less than 0.1 m a.
12345 rev. 1.10 15 n operation l operation of r3130n series vref delay circuit v dd gnd out + - ra rb comparator nch pch cmos output type out pin is connected to the drain of nch tr. and pch tr. in this ic. nch open drain output type out pin is connected to the drainf of nch tr. in this ic. (out pin should be pulled up to v dd or an external voltage level.) block diagram minimum operating voltage (v ddl ) gnd output voltage (out) supply voltage (v dd ) detector threshold(v det ) a b t delay gnd ?- ? =released voltage operating diagram in the above diagram, ? output voltage becomes equal to supply voltage ( nch open drain output type; equal to pull-up voltage). - when supply voltage is down to the detector threshold level (point a), vref 3 v dd rb / ( ra+rb ) is true. then, output of the comparator is reversed, thus output voltage becomes equal to gnd level. ? when supply voltage is lower than minimum operating voltage, output of transistor is indefinite, therefore output is also indefinite. output voltage is equal to gnd level. when supply voltage is higher than released voltage (point b), vref v dd rb / ( ra+rb ) is true. then output of the comparator is reversed, thus output voltage becomes equal to supply voltage ( nch open drain output type; equal to pull-up voltage). *there is no hysteresis range between detector threshold and released voltage.
12345 rev. 1.10 16 l operation of r3131n series vref delay circuit v dd gnd out + - ra rb comparator nch pch cmos output type: out pin is connected to the drain of nch tr. and pch tr. in this ic. nch open drain output type :i outpin is connected to the drain of nch tr. in this ic. (out pin should be pulled up to v dd or an external voltage level.) block diagram minimum operating voltage (v ddl ) gnd output voltage ( v out ) supply voltage ( v dd ) detector threshold(v det ) a b t delay gnd ?- ? =released voltage operation diagram in the above diagram, ? output voltage becomes equal to gnd level. - when supply voltage is down to the detector threshold level (point a), vref 3 v dd rb / ( ra+rb ) is true. then, output of the comparator is reversed, thus output voltage becomes equal to supply voltage (nch open drain output type; equal to pull-up voltage).. ? when supply voltage is lower than minimum operating voltage, output of transistor is indefinite, therefore output is also indefinite.(nch open drain output type; output voltage level is equal to pull-up voltage.) output voltage is equal to supply voltage. (nch open drain output type; equal to pull-up voltage.) when supply voltage is higher than released voltage (point b), vref v dd rb / ( ra+rb ) is true. then output of the comparator is reversed, thus output voltage becomes equal to gnd level after the output delay time. *there is no hysteresis range between detector threshold and released voltage.
12345 rev. 1.10 17 n test circuits l test circuit for supply current l test circuit for detector threshold (cmos output type; pull-up part is not necessary.) r313xn series out v dd gnd i ss r313xn series out v dd gnd v in v in v out 470k w 5v l test circuit for h output voltage (cmos output type only) l test circuit for l output voltage r313xn series out v dd gnd v in i out v oh v r313xn series out v dd gnd v in i out v ol v l test circuit for off leakage current l test circuit for output delay time (cmos output type; pull-up is not necessary.) 1.0v gnd (v det )+1.0v gnd output voltage 313xn series out v dd gnd input voltage v in v out t delay 100% 50% r3130n series r3131n series 313xn series out v dd gnd i oz v in v ds
12345 rev. 1.10 18 n typical characteristics 1) supply current vs. input voltage r3130n26xx3 r3131n26xx3 0.0 0.4 0.8 1.2 1.6 2.0 0123456 input voltage v in [v] supply current iss[ua] r3130n29xx3 r3131n29xx3 0.0 0.4 0.8 1.2 1.6 2.0 0123456 input voltage v in [v] supply current iss[ua ] r3130n30xx8 r3131n30xx8 0.0 0.4 0.8 1.2 1.6 2.0 0123456 input voltage v in [v] supply current iss[ua] r3130n40xx r3131n40xx 0.0 0.4 0.8 1.2 1.6 2.0 0123456 input voltage v in [v] supply current iss[ua ] r3130n44xx r3131n44xx 0.0 0.4 0.8 1.2 1.6 2.0 0123456 input voltage v in [v] supply current iss[ua ] r3130n46xx5 r3131n46xx5 0.0 0.4 0.8 1.2 1.6 2.0 0123456 input voltage v in [v] supply current iss[ua ] topt=85 c 25 c -40 c topt=85 c -40 c 25 c topt=85 c 25 c -40 c topt=85 c 25 c -40 c topt=85 c 25 c -40 c topt=85 c 25 c -40 c
12345 rev. 1.10 19 2) detector threshold vs. temperature r3130n26xx3 r3131n26xx3 2.57 2.59 2.61 2.63 2.65 2.67 -50 -25 0 25 50 75 100 temperature topt detector threshold -v det [v] r3130n29xx3 r3131n29xx3 2.87 2.89 2.91 2.93 2.95 2.97 2.99 -50 -25 0 25 50 75 100 temperature topt detector threshold -v det [v] r3130n30xx8 r3131n30xx8 3.01 3.03 3.05 3.07 3.09 3.11 3.13 -50 -25 0 25 50 75 100 temperature topt detector threshold -v det [v] r3130n40xx r3131n40xx 3.92 3.94 3.96 3.98 4.00 4.02 4.04 4.06 4.08 -50 -25 0 25 50 75 100 temperature topt detector threshold -vdet[v ] r3130n44xx r3131n44xx 4.29 4.31 4.33 4.35 4.37 4.39 4.41 4.43 4.45 -50 -25 0 25 50 75 100 temperature topt detector threshold -v det [v] r3130n46xx5 r3131n46xx5 4.53 4.55 4.57 4.59 4.61 4.63 4.65 4.67 4.69 -50 -25 0 25 50 75 100 temperature topt detector threshold -v det [v] 3) nch driver output current vs. v ds [ c] [ c] [ c] [ c] [ c] [ c]
12345 rev. 1.10 20 r3130n26xx3 0 2 4 6 8 10 0.0 0.5 1.0 1.5 2.0 v ds [v] nch driver output current i out [ma] r3130n29xx3 0 2 4 6 8 10 0.0 0.5 1.0 1.5 2.0 v ds [v] nch driver output current i out [ma] r3130n30xx8 0 2 4 6 8 10 0.0 0.5 1.0 1.5 2.0 v ds [v] nch driver output current i out [ma] r3130n40xx 0 5 10 15 20 0.0 0.5 1.0 1.5 2.0 2.5 3.0 v ds [v] nch driver output current i out [ma] r3130n44xx 0 5 10 15 20 0.0 0.5 1.0 1.5 2.0 2.5 3.0 v ds [v] nch driver output current i out [ma] r3130n46xx5 0 5 10 15 20 0.0 0.5 1.0 1.5 2.0 2.5 3.0 v ds [v] nch driver output current i out [ma] v dd= 2.0v 1.0v v dd= 2.0v 1.0v 1.0v v dd =2.0v v dd =3.0v 1.0v 2.0v v dd =4.0v 1.0v 2.0v 3.0v v dd =4.0v 3.0v 2.0v 1.0v
12345 rev. 1.10 21 r3131n26xx3 0 5 10 15 20 0.0 0.5 1.0 1.5 2.0 2.5 3.0 v ds [v] nch driver output current i out [ma] r3131n29xx3 0 5 10 15 20 0.0 0.5 1.0 1.5 2.0 2.5 3.0 v ds [v] nch driver output current i out [ma] r3131n30xx8 0 5 10 15 20 0.0 0.5 1.0 1.5 2.0 2.5 3.0 v ds [v] nch driver output current i out [ma] r3131n40xx 0 5 10 15 20 0.0 0.5 1.0 1.5 2.0 2.5 3.0 v ds [v] nch driver output current i out [ma] r3131n44xx 0 5 10 15 20 0.0 0.5 1.0 1.5 2.0 2.5 3.0 v ds [v] nch driver output current i out [ma] r3131n46xx5 0 5 10 15 20 0.0 0.5 1.0 1.5 2.0 2.5 3.0 v ds [v] nch driver output current i out [ma] v dd =3.0v 4.0v 5.0v 6.0v 6.0v 5.0v 4.0v v dd =3.0v v dd =4.0v 6.0v 5.0v 6.0v v dd =5.0v v dd =5.0v 6.0v 6.0v v dd =5.0v
12345 rev. 1.10 22 4) nch driver output current vs. input voltage r3130n26xx3 0 1 2 3 4 5 6 7 8 9 10 00.511.522.53 input voltage v in [v] nch driver output current i out [ma] r3130n29xx3 0 1 2 3 4 5 6 7 8 9 10 00.511.522.53 input voltage v in [v] nch driver output current i out [ma] r3130n30xx8 0 2 4 6 8 10 12 00.511.522.533.5 input voltage v in [v] nch driver output current i out [ma] r3130n40xx 0 2 4 6 8 10 12 012345 input voltage v in [v] nch driver output current i out [ma] r3130n44xx 0 2 4 6 8 10 12 14 012345 input voltage v in [v] nch driver output current i out [ma] r3130n46xx5 0 2 4 6 8 10 12 14 012345 input voltage v in [v] nch driver output current i out [ma] topt=-40 c 25 c 85 c topt=-40 c 25 c 85 c topt=-40 c 25 c 85 c topt=-40 c 25 c 85 c topt=-40 c 25 c 85 c topt=-40 c 25 c 85 c v ds =0.5v v ds =0.5v v ds =0.5v v ds =0.5v v ds =0.5v v ds =0.5v
12345 rev. 1.10 23 r3131n26xx3 0 2 4 6 8 10 12 14 16 0123456 input voltage v in [v] nch driver output current i out [ma] r3131n29xx3 0 2 4 6 8 10 12 14 16 0123456 input voltage v in [v] nch driver output current i out [ma] r3131n30xx8 0 2 4 6 8 10 12 14 16 0123456 input voltage v in [v] nch driver output current i out [ma] r3131n40xx 0 2 4 6 8 10 12 14 16 0123456 input voltage v in [v] nch driver output current i out [ma] r3131n44xx 0 2 4 6 8 10 12 14 16 0123456 input voltage v in [v] nch driver output current i out [ma] r3131n46xx5 0 2 4 6 8 10 12 14 16 0123456 input voltage v in [v] nch driver output current i out [ma] topt=-40 c 25 c 85 c topt=-40 c 25 c 85 c topt=-40 c 25 c 85 c topt=-40 c 25 c 85 c topt=-40 c 25 c 85 c topt=-40 c 25 c 85 c v ds =0.5v v ds =0.5v v ds =0.5v v ds =0.5v v ds =0.5v v ds =0.5v
12345 rev. 1.10 24 5) pch driver output current vs. input voltage r3130n26xx3 0 2 4 6 8 10 12 0123456 input voltage v in [v] pch driver output current i out [ma] r3130n29xx3 0 2 4 6 8 10 12 0123456 input voltage v in [v] pch driver output current i out [ma] r3130n30xx8 0 2 4 6 8 10 12 0123456 input voltage v in [v] pch driver output current i out [ma] r3130n40xx 0 2 4 6 8 10 12 0123456 input voltage v in [v] pch driver output current i out [ma] r3130n44xx 0 2 4 6 8 10 12 0123456 input voltage vin[v] pch driver output current i out [ma] r3130n46xx5 0 2 4 6 8 10 12 0123456 input voltage v in [v] pch driver output current i out [ma] v ds =-2.1v -1.5v -1.0v -0.5v v ds =-2.1v -1.5v -1.0v -0.5v v ds =-2.1v -1.5v -1.0v -0.5v v ds =-2.1v -1.5v -1.0v -0.5v v ds =-2.1v -1.5v -1.0v -0.5v v ds =-2.1v -1.5v -1.0v -0.5v
12345 rev. 1.10 25 r3131n26xx3 0 1 2 3 4 00.511.522.53 input voltage v in [v] pch driver output current i out [ma] r3131n29xx3 0 1 2 3 4 5 01234 input voltage v in [v] pch driver output current i out [ma] r3131n30xx8 0 1 2 3 4 5 01234 input voltage v in [v] pch driver output current i out [ma] r3131n40xx 0 1 2 3 4 5 6 7 8 012345 input voltage v in [v] pch driver output current i out [ma] r3131n44xx 0 2 4 6 8 10 012345 input volta g e v in [v] pch driver output current i out [ma] r3131n46xx5 0 2 4 6 8 10 012345 input voltage v in [v] pch driver output current i out [ma] v ds =-2.1v -1.5v -1.0v -0.5v v ds =-2.1v -1.5v -1.0v -0.5v v ds =-2.1v -1.5v -1.0v -0.5v v ds =-2.1v -1.5v -1.0v -0.5v v ds =-2.1v -1.5v -1.0v -0.5v v ds =-2.1v -1.5v -1.0v -0.5v
12345 rev. 1.10 26 6) output delay time at detection mode vs. temperature r3130n26xx3 r3131n26xx3 0 10 20 30 40 50 -50 -25 0 25 50 75 100 temperature topt output delay time at detection mode trst[us] r3130n29xx3 r3131n29xx3 0 10 20 30 40 50 -50 -25 0 25 50 75 100 temperature topt output delay time at detection mode trst[us] r3130n30xx8 r3131n30xx8 0 10 20 30 40 50 -50 -25 0 25 50 75 100 temperature topt output delay time at detection mode trst[us] r3130n40xx r3131n40xx 0 10 20 30 40 50 -50 -25 0 25 50 75 100 temperature topt output delay time at detection mode trst[us] r3130n44xx r3131n44xx 0 10 20 30 40 50 -50 -25 0 25 50 75 100 temperature topt output delay time at detection mode trst[us] r3130n46xx5 r3131n46xx5 0 10 20 30 40 50 -50 -25 0 25 50 75 100 temperature topt output delay time at detection mode trst[us] [ c] [ c] [ c] [ c] [ c] [ c]
12345 rev. 1.10 27 7) power-on reset delay time vs. temperature r3130nxxax r3131nxxax 35 45 55 65 75 -50 -25 0 25 50 75 100 temperature topt power-on reset delay time tdelay[ms] r3130nxxbx r3131nxxbx 60 80 100 120 140 -50 -25 0 25 50 75 100 temperature topt power-on reset delay time tdelay(ms) r3130nxxdx r3131nxxdx 150 175 200 225 250 -50 -25 0 25 50 75 100 temperature topt power-on reset delay time tdelay(ms) r3130nxxex r3131nxxex 200 240 280 320 360 -50 -25 0 25 50 75 100 temperature topt power-on reset delay time tdelay[ms] r3130nxxhx r3131nxxhx 300 350 400 450 500 -50 -25 0 25 50 75 100 temperature topt power-on reset delay time tdelay(ms) [ c] [ c] [ c] [ c]
12345 rev. 1.10 28 technical notes figure a figure b as shown wirin g in fi g ure a and fi g ure b may cause unstable operation by throu g h-type current at detection of all types of r313xn series. and detector threshold may shift because of volta g e drop by consumption current of this ic itself. r313xn out v dd gnd v dd r r313xn out v dd gnd v dd r1 r2 series series
12345 rev. 1.10 29 n package dimensions 2.9 1.9 (0.95) (0.95) 1.5 2.8 0.4 (0.8) 0 to 0.1 0.16 unit : mm 0.65 0.65 1.1

▲Up To Search▲

Price & Availability of R3130N29EA3-TR

	To Download R3130N29EA3-TR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .