89 radhard msi logic ut54acs153/ut54acts153 radiation-hardened dual 4 to 1 multiplexers features radiation-hardened cmos - latchup immune high speed low power consumption single 5 volt supply available qml q or v processes flexible package - 16-pin dip - 16-lead flatpack description the ut54acs153 and the ut54acts153 are dual four to one line selectors/multiplexers. common inputs a and b select a value from one of four sources for each section and routes the value from each section to their respective outputs. separate strobe inputs, g are provided for each of the two four-line sec- tions. the devices are characterized over full military temperature range of -55 c to +125 c. function table pinouts 16-pin dip top view 16-lead flatpack top view logic symbol select inputs data inputs output control output b a c0 c1 c2 c3 g y x x x x x x h l l l l x x x l l l l h x x x l h l h x l x x l l l h x h x x l h h l x x l x l l h l x x h x l h h h x x x l l l h h x x x h l h 1 2 3 4 5 7 6 16 15 14 13 12 10 11 1g b 1c3 1c2 1c1 1c0 1y v dd 2g a 2c3 2c2 2c1 2c0 8 9 v ss 2y 1 2 3 4 5 7 6 16 15 14 13 12 10 11 v dd 1g b 1c3 1c2 1c1 1c0 1y 2g a 2c3 2c2 2c1 2c0 v ss 2y 8 9 (14) a (2) b 1 0 mux note: 1. logic symbol in accordance with ansi/ieee std 91-1984 and iec publication 617-12. (1) 1g en (6) 1c0 0 (5) 1c1 (4) 1c2 (3) 1c3 (15) 2g (10) 2c0 (11) 2c1 (7) 1y 2c2 (13) 2c3 (9) 2y (12) 1 2 3 g 0 3 ---
radhard msi logic 90 ut54acs153/ut54acts153 logic diagram (7) 1y (9) 2y (1) (6) (5) (4) (3) (2) (14) (10) (11) (12) (13) 2c3 2c2 2c1 2c0 a b 1c3 1c2 1c1 1c0 1g (15) output control output control 2g data 1 data 2 select
91 radhard msi logic ut54acs153/ut54acts153 radiation hardness specifications 1 notes: 1. logic will not latchup during radiation exposure within the limits defined in the table. 2. device storage elements are immune to seu affects. absolute maximum ratings note: 1. stresses outside the listed absolute maximum ratings may cause permanent damage to the device. this is a stress rating only, functional operation of the device at these or any other conditions beyond limits indicated in the operational sections is not recommended. exposure to absolute ma ximum rating conditions for extended periods may affect device reliability. recommended operating conditions parameter limit units total dose 1.0e6 rads(si) seu threshold 2 80 mev-cm 2 /mg sel threshold 120 mev-cm 2 /mg neutron fluence 1.0e14 n/cm 2 symbol parameter limit units v dd supply voltage -0.3 to 7.0 v v i/o voltage any pin -.3 to v dd +.3 v t stg storage temperature range -65 to +150 c t j maximum junction temperature +175 c t ls lead temperature (soldering 5 seconds) +300 c jc thermal resistance junction to case 20 c/w i i dc input current 10 ma p d maximum power dissipation 1 w symbol parameter limit units v dd supply voltage 4.5 to 5.5 v v in input voltage any pin 0 to v dd v t c temperature range -55 to + 125 c
radhard msi logic 92 ut54acs153/ut54acts153 dc electrical characteristics 7 (v dd = 5.0v 10%; v ss = 0v 6 , -55 c < t c < +125 c) symbol parameter condition min max unit v il low-level input voltage 1 acts acs 0.8 .3v dd v v ih high-level input voltage 1 acts acs .5v dd .7v dd v i in input leakage current acts/acs v in = v dd or v ss -1 1 a v ol low-level output voltage 3 acts acs i ol = 8.0ma i ol = 100 a 0.40 0.25 v v oh high-level output voltage 3 acts acs i oh = -8.0ma i oh = -100 a .7v dd v dd - 0.25 v i os short-circuit output current 2 ,4 acts/acs v o = v dd and v ss -200 200 ma i ol output current 10 (sink) v in = v dd or v ss v ol = 0.4v 8 ma i oh output current 10 (source) v in = v dd or v ss v oh = v dd - 0.4v -8 ma p total power dissipation 2, 8, 9 c l = 50pf 2.1 mw/ mhz i ddq quiescent supply current delta acts for input under test v in = v dd - 2.1v for all other inputs v in = v dd or v ss v dd = 5.5v 1.6 ma i ddq quiescent supply current v dd = 5.5v 10 a c in input capacitance 5 = 1mhz @ 0v 15 pf c out output capacitance 5 = 1mhz @ 0v 15 pf
93 radhard msi logic ut54acs153/ut54acts153 notes: 1. functional tests are conducted in accordance with mil-std-883 with the following input test conditions: v ih = v ih (min) + 20%, - 0%; v il = v il (max) + 0%, - 50%, as specified herein, for ttl, cmos, or schmitt compatible inputs. devices may be tested using any input voltage within th e above specified range, but are guaranteed to v ih (min) and v il (max). 2. supplied as a design limit but not guaranteed or tested. 3. per mil-prf-38535, for current density 5.0e5 amps/cm 2 , the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765 pf/mhz. 4. not more than one output may be shorted at a time for maximum duration of one second. 5. capacitance measured for initial qualification and when design changes may affect the value. capacitance is measured between the designated terminal and v ss at frequency of 1mhz and a signal amplitude of 50mv rms maximum. 6. maximum allowable relative shift equals 50mv. 7. all specifications valid for radiation dose 1e6 rads(si). 8. power does not include power contribution of any ttl output sink current. 9. power dissipation specified per switching output. 10. this value is guaranteed based on characterization data, but not tested.
radhard msi logic 94 ut54acs153/ut54acts153 ac electrical characteristics 2 (v dd = 5.0v 10%; v ss = 0v 1 , -55 c < t c < +125 c) notes: 1. maximum allowable relative shift equals 50mv. 2. all specifications valid for radiation dose 1e6 rads(si). symbol parameter minimum maximum unit t phl data to output yn 2 16 ns t plh data to output yn 2 12 ns t phl strobe to output yn 1 15 ns t plh strobe to output yn 1 14 ns t phl select to output yn 2 16 ns t plh select to output yn 2 14 ns
|
