iec inlet ? lters fn 9263 general purpose power entry module with mains switch approvals rated currents up to 10a 1-pole rocker switch snap-in versions (s and s1 type) compact to ? t 1u rack size (cqc approval pending) typical applications the fn 9263 power entry module combines an iec inlet, mains filter with excellent filter attenuation and a mains switch in a small form factor. choosing the fn 9263 product line brings you the rapid availability of a standard filter associated with the necessary safety acceptances. standard iec connector filters are a practical solution helping you to pass emi system approval in a short time. a wide selection on amperage ratings and mounting possibilities are designed to offer you the desired solution. exceptional conducted attenuation performance, based on chokes with high saturation resistance and excellent thermal behavior. rear/front or snap-in mounting. small compact housing fitting 1u rack applications. versions up to 10a are available with 1 pole rocker switch. custom-specific versions are available on request. portable electrical and electronic equipment small to medium-sized machines and household equipment single-phase power supplies, switch-mode power supplies test and measurement equipment rack mounting equipment features and benefits technical specifications maximum continuous operating voltage: 250vac, 50/60hz operating frequency: dc to 400hz rated currents: 1 to 10a @ 40c max. high potential test voltage for capacitors: p C> e 2000vac for 2 sec p C> n 760vac for 2 sec protection category: ip40 according to iec 60529 temperature range (operation and storage): -25c to +85c (25/85/21) design corresponding to: ul 1283, csa 22.2 no. 8 1986, iec/en 60939 flammability corresponding to: ul 94v-2, ul 94v-0 or better mtbf @ 40c/230v (mil-hb-217f): 6,500,000 hours rocker switch description: function: 1-pole, dark not illuminated marking i - 0 electrical specifications: inrush current 78a 10,000 on-off operations according to ul 1054, tv 5 switch ratings: usa (ul): 10a, 125vac; 8a, 250vac; 1/4hp canada (csa): 10a, 250vac; 1/4hp europe (enec): 20a (4a), 250vac* china (cqc): 10a, 250vac typical electrical schematic n e p line switch cx r 2xl 2xcy n e p load * value in () relates to the inductive current charge: cos = 0.65
> components > fn 9263 filter selection table fn 9263x-1-06-y 1 (1.2) 373 5.3 0.1 2.2 1000 -06 55 fn 9263x-2-06-y 2 (2.3) 373 2.7 0.1 2.2 1000 -06 55 fn 9263x-3-06-y 3 (3.5) 373 2 0.1 2.2 1000 -06 55 fn 9263x-4-06-y 4 (4.6) 373 1 0.1 2.2 1000 -06 55 fn 9263x-6-06-y 6 (6.9) 373 0.3 0.1 2.2 1000 -06 55 fn 9263x-8-06-y 8 (9.2) 373 0.25 0.1 2.2 1000 -06 55 fn 9263x-10-06-y 10 (11.5) 373 0.2 0.1 2.2 1000 -06 55 * maximum leakage under normal operating conditions. note: if the neutral line is interrupted, worst case leakage could reach t wice this level. filter rated current leakage current* inductance capacitance resistance output connections weight @ 40c (25c) @ 250vac/50hz l cx cy r [a] [a] [mh] [f] [nf] [k] [g] product selector fn 9263x-yy-yy-y snap-in range for s version only blank: snap-in range 0.6 to 1.5mm 20: snap-in range 1.6 to 2.5mm 30: snap-in range 2.6 to 3.5mm 06: faston 6.3 x 0.8mm (spade/soldering) 1 to 10: rated current blank: standard housing with mounting ? anges s: snap-in version, snapper on vertical side s1: snap-in version, snapper on horizontal side per cispr 17; a = 50/50 sym; b = 50/50 asym; c = 0.1/100 sym; d = 100/0.1 sym typical filter attenuation 1 to 4a types 6 to 10a types for example: fn 9263-1-06, fn 9263s-10-06-20, fn 9263s1-6-06-30
> components > fn 9263 mechanical data fn 9263 fn 9263s fn 9263s1 panel cut out installation a c b e h g s fd i 6.3 x 0.8 j a b e g fd i j 6.3 x 0.8 n r m p c 6.3 x 0.8 j i d f b a g e t fn 9263 fn 9263s fn 9263s1 tolerances dimensions a 46 34 34 0.3 b 35 35 35 c 36 d 41 41 41 0.3 e 27.9 27.9 27.9 +0.2/-0 f 5.5 5.5 5.5 0.3 g 32.2 32.2 32.2 +0/-0.2 h ?3.3 0.1 i 13.8 13.8 13.8 j 12.5 12.5 12.5 0.3 m r 3.5 r 3.5 r 3.5 n 33.2 32.6 33.3 0.1 p 29.2 29.0 28.3 0.1 r m3 s 90 t* 0.6 - 1.5 0.6 - 1.5 t* 1.6 - 2.5 1.6 - 2.5 t* 2.6 - 3.5 2.6 - 3.5 * for selecting the panel thickness, please refer to the filter selector table. all dimensions in mm; 1 inch = 25.4mm tolerances according: iso 2768-m / en 22768-m your local partner: to find your local partner within schaffners global network, please go to www.schaffner.com may 2008
|
