 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 179 push-pull connectors hr10 series features 1. "a little giant" the most compact hr10 series is as slender as a cigarette but it fits every application with well-balanced, simplified layout in limited space. 2. easy "push-pull" operation one touch "push-pull" coupling mechanism assures easy and quick connecting and disconnecting. you can couple it accurately just by pushing any part of the connector housing. 3. polarization five-key system permits only one way of coupling so that you can find right position to connect even when blind mating. 4. protection of connection pin a connector pin is located to avoid any damage which may be caused when blind mating. 5. high density the space-saving "push-pull" mechanism facilitates multi-installation of connectors. 6. easy wiring and mounting no use of screws makes wireing and mounting easier. 7. simple and refined appearance simple and well designed connectors with matte finish enhance the appearance of the equipment. overview the hr10 series connectors are push-pull coupling type micro-connectors.they have been developed in response to customers' needs for miniaturization, high density, and easy handling.the hr10 series connectors offer light weight and assure high reliavility and durability as well as easy "push-pull" operation. you may apply the hr10 series connectors to all kinds of small-sized electronic equipment requiring high reliability.however, these simple but refined connectors are most suitable for portable electronic equipment which requires good appearance. t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n .
180 hr10 seriespush-pull connectors materials part material finish shell zinc alloy and brass satin-fnished nickel plate insulator polyamide / pbt (blue or black) male terminal brass / bronze silver or gold plating female terminal beryllium / phosphor bronze silver or gold plating ordering information hr10 a ? 7 p ? 4 p a ( ** ) 1 2 3 4 5 6 7 8 4 shell type p:plug j:jack r:receptacle 5 number of contacts 6 type of terminal p:male terminal s:female terminal 7 terminal form c:crimp connection system 8 other specifcations:2 numerical digits will be added when there is a specifcations change other than shown in positions 1 to 7 1 series name:hr10 series 2 type a:low-cost model g:shielded e:built-in capacitor b:coaxail terminal d:connector sleeve rotation inhibited 3 shell size: plug mating part outside diameter in mm t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 181 hr10 seriespush-pull connectors plug receptacle unit : mm hrs no. part no. no.of pins a ?b ?c ?d weight 110-0021-6-73 hr10-7p-4p(73) 4 28.5 11 7 5.2 8g 110-0022-9-73 hr10-7p-4s(73) 4 28.5 11 7 5.2 8g 110-0023-1-73 hr10-7p-6p(73) 6 28.5 11 7 5.2 8g 110-0024-4-73 hr10-7p-6s(73) 6 28.5 11 7 5.2 8g 110-0025-7-73 hr10-10p-12p(73) 12 32.5 14 9.5 7.2 15g 110-0026-0-73 hr10-10p-12s(73) 12 32.5 14 9.5 7.2 15g unit : mm hrs no. part no. no.of pins a ?b ?c d e weight 110-0031-0-73 hr10-7r-4s(73) 4 14 11 8.85 m80.5 10 3.5g 110-0032-2-73 hr10-7r-4p(73) 4 14 11 8.85 m80.5 10 3.5g 110-0033-5-73 hr10-7r-6s(73) 6 14 11 8.85 m80.5 10 3.5g 110-0034-8-73 hr10-7r-6p(73) 6 14 11 8.85 m80.5 10 3.5g 110-0035-0-73 hr10-10r-12s(73) 12 16 14 11.9 m110.75 13 6g 110-0036-3-73 hr10-10r-12p(73) 12 16 14 11.9 m110.75 13 6g remarks : for mounting holes, see page 198. hr10 type hr10-7p-6p(73) (an example in shape) (an example in shape) hr10-10p-12p(73) hr10-7r-6s(73) hr10-10r-12s(73) t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 182 hr10 seriespush-pull connectors plug (pcb dip type) jack unit : mm hrs no. part no. no.of pins a ?b ?c d weight 110-0027-2-73 hr10-7j-4s(73) 4 28.5 11 8.85 5.2 7g 110-0028-5-73 hr10-7j-4p(73) 4 28.5 11 8.85 5.2 7g 110-0029-8-73 hr10-7j-6s(73) 6 28.5 11 8.85 5.2 7g 110-0030-7-73 hr10-7j-6p(73) 6 28.5 11 8.85 5.2 7g 110-0037-6-73 hr10-10j-12s(73) 12 32.5 14 11.9 7.2 14g 110-0038-9-73 hr10-10j-12p(73) 12 32.5 14 11.9 7.2 14g unit : mm hrs no. part no. no.of pins ?a ?b c d e f g weight 110-0059-9-73 hr10-7r-4sa(73) 4 11 8.85 m80.5 10 6.3 0.5 15.5 3g 110-0050-4-73 hr10-7r-6sa(73) 6 11 8.85 m80.5 10 6.3 0.5 15.5 3g 110-0061-0-73 hr10-7r-6pa(73) 6 11 8.85 m80.5 10 6.3 0.5 15.5 3g 110-0049-5-73 hr10-10r-12sa(73) 12 14 11.9 m110.75 13 6.3 0.5 15.5 5g 110-0055-8-73 hr10-10r-12pa(73) 12 14 11.9 m110.75 13 6.3 0.5 15.5 5g remarks : 1.for mounting holes, see page 198. 2.for dip post arrangement, see page 193. hr10-7r-6sa(73) hr10-10r-12sa(73) hr10-7j-6s(73) (an example in shape) dip post dia. ?0.55 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 183 hr10 seriespush-pull connectors plud (solder type) plug (crimp type) unit : mm hrs no. part no. no.of pins a ?b ?c ?d weight 110-0301-2-73 hr10a-7p-4p(73) 4 35 11.5 7 5 9g 110-0302-5-73 hr10a-7p-4s(73) 4 35 11.5 7 5 9g 110-0318-5-73 hr10a-7p-5p(73) 5 35 11.5 7 5 9g 110-0319-8-73 hr10a-7p-5s(73) 5 35 11.5 7 5 9g 110-0303-8-73 hr10a-7p-6p(73) 6 35 11.5 7 5 9g 110-0304-0-73 hr10a-7p-6s(73) 6 35 11.5 7 5 9g 110-0407-3-73 hr10a-10p-10p(73) 10 43 14.7 9.5 7 16g 110-0408-6-73 hr10a-10p-10s(73) 10 43 14.7 9.5 7 16g 110-0401-7-73 hr10a-10p-12p(73) 12 43 14.7 9.5 7 16g 110-0402-0-73 hr10a-10p-12s(73) 12 43 14.7 9.5 7 16g 110-0713-0-73 hr10a-13p-20p(73) 20 58.8 19 13 7 37g 110-0716-8-73 hr10a-13p-20s(73) 20 58.8 19 13 7 37g unit : mm hrs no. part no. no.of pins a ?b ?c ?d weight 110-0501-1-73 hr10a-7p-4pc(73) 4 35 11.5 7 5 9g 110-0502-4-73 hr10a-7p-4sc(73) 4 35 11.5 7 5 9g 110-0503-7-73 hr10a-7p-6pc(73) 6 35 11.5 7 5 9g 110-0504-0-73 hr10a-7p-6sc(73) 6 35 11.5 7 5 9g 110-0601-6-73 hr10a-10p-10pc(73) 10 43 14.7 9.5 7 16g 110-0602-9-73 hr10a-10p-10sc(73) 10 43 14.7 9.5 7 16g 110-0603-1-73 hr10a-10p-12pc(73) 12 43 14.7 9.5 7 16g 110-0604-4-73 hr10a-10p-12sc(73) 12 43 14.7 9.5 7 16g 110-0701-0-73 hr10a-13p-20pc(73) 20 58.8 19 13 7 37g 110-0702-3-73 hr10a-13p-20sc(73) 20 58.8 19 13 7 37g hr10a10g type hr10a-7p-6p(73) hr10a-10p-12p(73) hr10a-7p-6pc(73) hr10a-10p-12pc(73) (an example in shape) (an example in shape) t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 184 hr10 seriespush-pull connectors receptacle (solder type) receptacle (crimp type) hrs no. part no. no.of pins a ?b ?c d e weight 110-0305-3-73 hr10a-7r-4s(73) 4 14 11 8.85 m80.5 10 3g 110-0306-6-73 hr10a-7r-4p(73) 4 14 11 8.85 m80.5 10 3g 110-0320-7-73 hr10a-7r-5s(73) 5 14 11 8.85 m80.5 10 3g 110-0321-0-73 hr10a-7r-5p(73) 5 14 11 8.85 m80.5 10 3g 110-0307-9-73 hr10a-7r-6s(73) 6 14 11 8.85 m80.5 10 3g 110-0308-1-73 hr10a-7r-6p(73) 6 14 11 8.85 m80.5 10 3g 110-0409-9-71 hr10a-10r-10s(71) 10 16 14 11.9 m110.75 13 5g 110-0410-8-73 hr10a-10r-10p(73) 10 16 14 11.9 m110.75 13 5g 110-0403-2-71 hr10a-10r-12s(71) 12 16 14 11.9 m110.75 13 5g 110-0404-5-73 hr10a-10r-12p(73) 12 16 14 11.9 m110.75 13 5g 110-0714-2-73 hr10a-13r-20s(73) 20 19.2 18 15.4 m140.75 17 8g 110-0715-5-73 hr10a-13r-20p(73) 20 20.2 18 15.4 m140.75 17 8g hrs no. part no. no.of pins a ?b ?c d e weight remarks 110-1601-1-73 hr10g-7r-4s(73) 4 14 11 8.85 m80.5 10 3g shield type 110-1602-4-73 hr10g-7r-4p(73) 4 14 11 8.85 m80.5 10 3g 110-1605-2-73 hr10g-7r-6s(73) 6 14 11 8.85 m80.5 10 3g 110-1606-5-73 hr10g-7r-6p(73) 6 14 11 8.85 m80.5 10 3g 110-1607-8-71 hr10g-10r-10s(71) 10 16 14 11.9 m110.75 13 5g 110-1608-0-73 hr10g-10r-10p(73) 10 16 14 11.9 m110.75 13 5g 110-1609-3-71 hr10g-10r-12s(71) 12 16 14 11.9 m110.75 13 5g 110-1610-2-73 hr10g-10r-12p(73) 12 16 14 11.9 m110.75 13 5g hrs no. part no. no.of pins a ?b c d e f weight 110-0506-5-73 hr10a-7r-4sc(73) 4 11 8.85 m80.5 10 6.3 12 3g 110-0505-2-73 hr10a-7r-4pc(73) 4 11 8.85 m80.5 10 6.3 12.2 3g 110-0508-0-73 hr10a-7r-6sc(73) 6 11 8.85 m80.5 10 6.3 12 3g 110-0507-8-73 hr10a-7r-6pc(73) 6 11 8.85 m80.5 10 6.3 12.2 3g 110-0606-0-71 hr10a-10r-10sc(71) 10 14 11.9 m110.75 13 6.3 12 5g 110-0605-7-71 hr10a-10r-10pc(71) 10 14 11.9 m110.75 13 6.3 12.2 5g 110-0608-5-71 hr10a-10r-12sc(71) 12 14 11.9 m110.75 13 6.3 12 5g 110-0607-2-71 hr10a-10r-12pc(71) 12 14 11.9 m110.75 13 6.3 12.2 5g 110-0703-6-73 hr10a-13r-20sc(73) 20 18 15.4 m140.75 17 9.3 15 8g 110-0704-9-73 hr10a-13r-20pc(73) 20 18 15.4 m140.75 17 9.3 15 8g unit : mm unit : mm hr10a-7r-6s(73) hr10a-7r-6sc(73) (an example in shape) (an example in shape) hr10g-10r-12s(71) hr10g-10r-12sc(71) hrs no. part no. no.of pins a ?b c d e f weight remarks 110-1701-6-73 hr10g-7r-4sc(73) 4 11 8.85 m80.5 10 6.3 12 3g shield type 110-1702-9-73 hr10g-7r-4pc(73) 4 11 8.85 m80.5 10 6.3 12.2 3g 110-1705-7-73 hr10g-7r-6sc(73) 6 11 8.85 m80.5 10 6.3 12 3g 110-1706-0-73 hr10g-7r-6pc(73) 6 11 8.85 m80.5 10 6.3 12.2 3g 110-1707-2-71 hr10g-10r-10sc(71) 10 14 11.9 m110.75 13 6.3 12 5g 110-1708-5-71 hr10g-10r-10pc(71) 10 14 11.9 m110.75 13 6.3 12.2 5g 110-1709-8-71 hr10g-10r-12sc(71) 12 14 11.9 m110.75 13 6.3 12 5g 110-1710-7-73 hr10g-10r-12pc(73) 12 14 11.9 m110.75 13 6.3 12.2 5g 110-1711-0-73 hr10g-13r-20sc(73) 20 18 15.4 m140.75 17 9.3 15 8g 110-1712-2-73 hr10g-13r-20pc(73) 20 18 15.4 m140.75 17 9.3 15 8g t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 185 hr10 seriespush-pull connectors receptacle (dip type) dust cap unit : mm hrs no. part no. no.of pins ?a ?b c d e f g weight remarks 110-0314-4-73 hr10a-7r-4sb(73) 4 11 8.85 m80.5 10 6.3 0.5 15.6 3g 110-0315-7-73 hr10a-7r-4pb(73) 4 11 8.85 m80.5 10 6.3 0.5 15.6 3g 110-0322-2-73 hr10a-7r-5sb(73) 5 11 8.85 m80.5 10 6.3 0.5 15.6 3g 110-0316-0-73 hr10a-7r-6sb(73) 6 11 8.85 m80.5 10 6.3 0.5 15.6 3g 110-0317-2-73 hr10a-7r-6pb(73) 6 11 8.85 m80.5 10 6.3 0.5 15.6 3g 110-0413-6-71 hr10a-10r-10sb(71) 10 14 11.9 m110.75 13 6.3 0.5 15.6 5g 110-0414-9-71 hr10a-10r-10pb(71) 10 14 11.9 m110.75 13 6.3 0.5 15.6 5g 110-0415-1-71 hr10a-10r-12sb(71) 12 14 11.9 m110.75 13 6.3 0.5 15.6 5g 110-0416-4-71 hr10a-10r-12pb(71) 12 14 11.9 m110.75 13 6.3 0.5 15.6 5g 110-0707-7-73 hr10a-13r-20sb(73) 20 18 15.4 m140.75 17 9.3 0 17.8 8g 110-0708-0-73 hr10a-13r-20pb(73) 20 18 15.4 m140.75 17 9.3 0 17.8 8g 110-1801-0-73 hr10g-7r-4sb(73) 4 11 8.85 m80.5 10 6.3 0.5 15.6 3g shield type 110-1802-3-73 hr10g-7r-4pb(73) 4 11 8.85 m80.5 10 6.3 0.5 15.6 3g 110-1805-1-73 hr10g-7r-6sb(73) 6 11 8.85 m80.5 10 6.3 0.5 15.6 3g 110-1806-4-73 hr10g-7r-6pb(73) 6 11 8.85 m80.5 10 6.3 0.5 15.6 3g 110-1807-7-71 hr10g-10r-10sb(71) 10 14 11.9 m110.75 13 6.3 0.5 15.6 5g 110-1808-0-71 hr10g-10r-10pb(71) 10 14 11.9 m110.75 13 6.3 0.5 15.6 5g 110-1809-2-71 hr10g-10r-12sb(71) 12 14 11.9 m110.75 13 6.3 0.5 15.6 5g 110-1810-1-71 hr10g-10r-12pb(71) 12 14 11.9 m110.75 13 6.3 0.5 15.6 5g 110-1811-4-73 hr10g-13r-20sb(73) 20 18 15.4 m140.75 17 9.3 0 17.8 8g 110-1812-7-73 hr10g-13r-20pb(73) 20 18 15.4 m140.75 17 9.3 0 17.8 8g remarks : 1.for mounting holes, see page 198. 2.for dip post arrangement, see page 193. unit : mm hrs no. part no. ?a b ?c ?d ?e 110-0058-6-00 hr10-7r-c 11 7 8 11.2 13 110-0052-0-00 hr10-10r-c 14 8.5 10.8 14 15 110-0452-8-00 hr10a-13r-c 17.5 11.5 14 18.1 19 hr10a-7r-6sb(73) hr10-7r-c (an example in shape) (an example in shape) hr10g-10r-12sb(71) dip post dia. 0.20.5 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 186 hr10 seriespush-pull connectors jack (solder type) unit : mm hrs no. part no. no.of pins a ?b ?c ?d weight 110-0309-4-73 hr10a-7j-4s(73) 4 35.3 11 8.85 5.5 9g 110-0310-3-73 hr10a-7j-4p(73) 4 35.3 11 8.85 5.5 9g 110-0311-6-73 hr10a-7j-6s(73) 6 35.3 11 8.85 5.5 9g 110-0312-9-73 hr10a-7j-6p(73) 6 35.3 11 8.85 5.5 9g 110-0411-0-73 hr10a-10j-10s(73) 10 43 14 11.9 7 16g 110-0412-3-73 hr10a-10j-10p(73) 10 43 14 11.9 7 16g 110-0405-8-73 hr10a-10j-12s(73) 12 43 14 11.9 7 16g 110-0406-0-73 hr10a-10j-12p(73) 12 43 14 11.9 7 16g jack (crimp type) unit : mm hrs no. part no. no.of pins a ?b ?c ?d weight 110-0510-2-73 hr10a-7j-4sc(73) 4 35.3 11 8.85 5.5 9g 110-0512-8-73 hr10a-7j-6sc(73) 6 35.3 11 8.85 5.5 9g 110-0610-7-73 hr10a-10j-10sc(73) 10 43 14 11.9 5.5 16g 110-0612-2-73 hr10a-10j-12sc(73) 12 43 14 11.9 5.5 16g 110-0705-1-73 hr10a-13j-20sc(73) 20 58.5 18 15.4 8.5 37g 110-0706-4-73 hr10a-13j-20pc(73) 20 58.5 18 15.4 8.5 37g hr10a-7j-6s(73) hr10a-10j-12s(73) hr10a-7j-6sc(73) (an example in shape) (an example in shape) t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 187 hr10 seriespush-pull connectors plug receptacle unit : mm hrs no. part no. a ?b applicable coaxial contact 110-0901-0-73 hr10b-10p-10pc(73) 50 5 hr10b-2.5cj(73) 110-0906-3-73 hr10b-10pa-10pc(73) 43 7 hr10b-2.5cj(73) unit : mm hrs no. part no. applicable coaxial contact 110-0902-2-71 hr10b-10r-10sc(71) hr10b-2.5cp(73) remarks : for mounting holes, see page 198. hr10b type connector the hr10b connector combines 10 signal lines and one coaxial contact in the standard number 10 shell. electrical performance are same as hr10a connector except coaxial contacts. performance specifications for the coaxial contacts are on the next page. hr10b-10p-10pc(73) hr10b-10r-10sc(71) (an example in shape) t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 188 hr10 seriespush-pull connectors plug jack material performance unit : mm hrs no. part no. applicable cable applicable connector 110-0904-8-73 hr10b-2.5cp(73) 0.8d-qew-cw (by fjikura wire) hr10b-10r-10sc(71) unit : mm hrs no. part no. applicable cable applicable connector 110-0903-5-73 hr10b-2.5cj(73) 0.8d-qew-cw (by fjikura wire) hr10b-10p-10pc(71) part material finish plug shell brass gold plating jack shell brass gold plating insulator tetra? uoride resin male pin phosphor bronze gold plating female pin beryllium copper gold plating description test data impedance 50? insulation resistance 1000m? or more at dc250v contact resistance center 6.5m? or less and outer 4m? or less at dc1a withstanding voltage ac250v r.m.s for 1minute v.s.w.r 1.3 or less for 0 to 1000mhz pull force 4.9n 500gf or more coaxial contacts the coaxial contacts shown here are for use with the hr10b connector.these contacts have locking barbs and are inserted from the rear of connector.please use the following information to select the correct terminals. hr10b-2.5cp(73) hr10b-2.5cj(73) (clamp) (clamp) t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 189 hr10 seriespush-pull connectors cable connecting methods hr10b-2.5cp hr10b-2.5cj 1.cable end treatment fig.1 1. dimensions for cable end treatment are shown in fig 1. 2.termination is described below. (1).strip cable outer jacket as indicated. (2).slit outer jacket on both sides per fig.1. (3).fold back outer cover. (4).remove insulator from cable. 2. soldering male pin to cable center conductor. fig.2 1. solder male pin to cable center conductor as indicated in fig.2. (1). pre-solder the solder pot of pin with ? 0.5mm string solder. (2). male pin should fit flush against the cable insulator as shown. (3). remove any excess solder from the pin with a knife.this surface must be smooth. (4). a properly soldered terminal will yield 500gf when stretched. 3.crimping cable outer conductor fig.3 1. insert cable prepared per process 2 into the connector.the cable should be inserted until it comes to a full stop.this may be verified by checking the dimension from the side of the connector to the top of the contact(as indicated in fig 3). this dimension should be a. 2. crimp this installed metal clamp with tool hr10- tc-01 per fig.3 and remove excess insulation with a knife. it is possible to pull back the contact. hold cable when crimping metal clamp and keep the dimension to show in fig 3. after crimping metal clamp. 110.5 1.40.2 3.70.2 (2.5) slit cable outer jaket 2 pieces (180 reverse side) malu pin or female pin soldering should fix flush contact fixing jig such as vise clamp metal (hr10b-2.5cp) a connector remove excess insulator material (remaining after clamping is complated) with a knife or aimilarobject. table 1 dimenshion a 2.5cp 2.5cj 1.50.2mm 0 mm +0.3 0 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 190 hr10 seriespush-pull connectors plug (solder type) plug (crimp type) unit : mm hrs no. part no. no.of pins 110-0455-6-73 hr10a-10tp-12pc(73) 12 hr10a-[ ]t type (threaded coupling type) hr10a-( )t connector is a new product having a threaded coupling locking mechanism.electric parformance is same as hr10 and hr10a push-pull locking type connector. unit : mm hrs no. part no. no.of pins ?a b ?c d ?e remarks 110-0331-3-73 hr10a-7tp-6p(73) 6 12 m100.75 7 m80.5 5 110-0331-3-74 hr10a-7tp-6p(74) 6 12 m100.75 7 m80.5 5 gold plating 110-0432-0-73 hr10a-10tp-12p(73) 12 17 m130.75 9.5 m80.5 7 110-0446-5-73 hr10a-10tpa-12s(73) 12 17 m130.75 9.5 m80.5 7 110-1101-9-73 hr10a-10wtp-12p(73) 12 15 m120.75 9.5 m110.75 6.5 * 110-1106-2-73 hr10a-10wtp-12s(73) 12 15 m120.75 9.5 m110.75 6.5 * 110-1015-9-73 hr10a-13tpd-20p(73) 20 20 m171 13 m110.75 7 *waterproof plug need resin f lling inside when connector assembly. when mated, the connector against water penetration. hr10a-10tp-12p(73) hr10a-10tp-12pc(73) t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 191 hr10 seriespush-pull connectors receptacle (solder type) receptacle (crimp type) receptacle (dip type) unit : mm hrs no. part no. no.of pins a ?b c ?d e f remarks 110-0089-0-73 hr10-7tr-6s(73) 6 m100.75 6.3 m80.5 11 14 10 gold plating 110-0453-0-73 hr10a-10tr-12s(73) 12 m130.75 6.3 m110.75 14 16 13 110-1104-7-73 hr10a-10wtr-12s(73) 12 m120.75 6.8 m10.50.75 14 16 13 remarks:for mounting hole, see page 192(10tr,10wtr) 198(7tr) unit : mm hrs no. part no. no.of pins ?a b c ?d e f 110-0456-9-73 hr10a-10tr-12sc(73) 12 14 12 6.3 m130.75 m110.75 13 110-1002-7-73 hr10a-13tr-20sc(73) 20 18 15 9.3 m171 m140.75 17 remarks:for mounting hole, see page 192 unit : mm hrs no. part no. no.of pins ?a b c d e f e h 110-0330-0-73 hr10a-7tr-6sa(73) 6 11 m100.75 m80.5 10 6.3 0.5 15.5 ?0.55 110-0433-3-73 hr10a-10tr-12sb(73) 12 14 m130.75 m110.75 13 6.3 0.5 15.5 0.20.5 110-0457-1-73 hr10a-10tr-12pb(73) 12 14 m130.75 m110.75 13 6.3 0.5 15.5 0.20.5 110-0445-2-73 hr10a-10tr-12pe(73) 12 14 m130.75 m110.75 13 6.3 0.5 14 0.20.5 110-1102-1-73 hr10a-10wtr-12sb(73) 12 14 m120.75 m10.50.75 13 6.8 0 15.5 0.20.5 110-1013-3-73 hr10a-13tr-20pb(73) 20 18 m171 m140.75 17 9.3 0 17.8 0.20.5 110-1014-6-73 hr10a-13tr-20sb(73) 20 18 m171 m140.75 17 9.3 0 17.8 0.20.5 remarks : 1.for mounting holes, see page 192. however, 7tr size shell be referred to page 198 on the shell size 7. 2.for dip post arrangement, see page 193. hr10a-10tr-12s(73) hr10a-10tr-12sc(73) hr10a-10tr-12pb(73) (an example in shape) (an example in shape) (an example in shape) dip post ? h t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 192 hr10 seriespush-pull connectors jack (solder type) unit : mm hrs no. part no. no.of pins ?a b ?c d remarks 110-0436-1-73 hr10a-10tj-12s(73) 12 14.7 41.3 7 m130.75 110-0459-7-73 hr10a-10tj-12p(73) 12 14.7 41.3 7 m130.75 110-1103-4-73 hr10a-10wtj-12s(73) 12 14 46.5 6.5 m120.75 * *waterproof jack need resin f lling inside when connector assembly. when mated, the connector against water penetration. panel mounting hole dimensions (screw coupling) the mounting hole dimensions shown below are for connectors to be tightened by a hexagonal nut from the back of the panel. the dimensions below apply only to the hr10a-( )t and not the 7tr. for the dimensions of connectors of other types, see page 198. hr10a-10tj-12s(73) type hr10a-10tr (panel thickness 1 to 2mm) (an example in shape) type hr10a-10wtr (panel 1 thickness 1 to 2mm) type hr10a-13tr (panel thickness 1 to 1.5mm) t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 193 hr10 seriespush-pull connectors receptacle dip post arrangement dimensions contact unit : mm type hrs no. part no. type of plating applicable cable loose contact 110-0515-6 hr10-pc-111 partial gold plating awg#26 to #30 110-0513-0 hr10-pc-112 silver plating awg#26 to #30 chain contact 110-0516-9 hr10-pc-211 partial gold plating awg#26 to #30 110-0514-3 hr10-pc-212 silver plating awg#26 to #30 remarks : 1.use cables with a coating outside diameter of 1mm or less. 2. loose-picce terminal are available in packs. each pack contains 100 terminals. strip terminals are available in reels. each reel contains 10,000 terminals. unit : mm type hrs no. part no. type of plating applicable cable loose contact 112-0410-0 hr12-sc-111 partial gold plating awg#26 to #30 112-0411-3 hr12-sc-112 silver plating awg#26 to #30 chain contact 112-0407-6 hr12-sc-211 partial gold plating awg#26 to #30 112-0408-9 hr12-sc-212 silver plating awg#26 to #30 remarks : 1.use cables with a coating outside diameter of 1mm or less. 2. loose-picce terminal are available in packs. each pack contains 100 terminals. strip terminals are available in reels. each reel contains 10,000 terminals. male pin female pin remarks : 1. the above fgures are views of receptacle-socket inserts from the mating side and plug-pin inserts from the wiring-connection side. 2. dimensional tolerance of 0.05 is recommended for the board arrangement. 7-size 4 cores 7-size 5 cores 7-size 6 cores 10-size 10 cores 10-size 12 cores 13-size 20 cores (4 places) (5 places) (6 places) (10 places) (12 places) (20 places) t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 194 hr10 seriespush-pull connectors tools type item hrs no. part no. applicable terminal applicable cable manual manual crimping tool 150-0052-9 hr12-sc-tc hr10-pc-112 awg#26 to #30 hr12-sc-112 automatic automatic crimping machine body 901-0005-4 cm-105 CC CC applicator 901-2015-9 ap105-hr12-1 hr10-pc-211 hr10-pc-212 awg#26 to #30 hr10-sc-211 hr10-sc-212 cable crimping tool 150-0036-2 hr10-tc-01 CC (hr10b-2.5cp, hr10b-2.5cj) 150-0041-2 hr10a-tc-02 ?5, ?7 extractor 150-0050-3 hr12-sc-tp hr12-sc-112 CC hr12-sc-212 150-0039-0 rp6-sc-tp hr10-pc-112 hr10-pc-212 150-0061-0 hr10b-tp hr10b-2.5cp hr10b-2.5cj (hr12-sc-tc) hand crimp tool (hr10a-tc-02) hand cable crimp tool (hr10b-tp) coaxial contact removal tool (hr12-sc-tp) auto crimp tool cm-105 (rp6-sc-tp) extraction tool t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 195 hr10 seriespush-pull connectors how to use a connector 1.inserting 2.withdrawing hr10 type hr10a type hold the plug at point a, align the plug guide with the receptacle guide, and push the plug straight. the plug will mate with the receptacle smoothly. hold the plug connection sleeve b and pull the sleeve straight. the plug will come off easily. jack (solder type) hrs no. part no. applicable connector 150-0009-0 hr10-7p-t01 hr10-7p 150-0010-9 hr10-10p-t02 hr10-10p 150-0011-1 hr10-7j-t03 hr10-7j 150-0012-4 hr10-10j-t04 hr10-10j 150-0059-8 hr10-13p-t05 hr10-13p 150-0060-7 hr10-13j-t06 hr10-13j hr10-10p-t02 hr10-10j-t04 panel plug a cable receptacle panel plug cable a receptacle panel b cable plug connection sleeve panel cable b plug connection sleeve t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 196 hr10 seriespush-pull connectors connection work procedure(plug side) this applies also to the jack side connection work. no special connection work procedure is given here for the receptacle side because no special procedure is necessary. hr10 type hr10a type table 2 spanner jaw distance size hr10 hr10a size 7 8 7.5 size 10 11 9.5 size 13 CC 13 table 1 size tightening force size 7 1.5n?m(15kg?cm) size 10 2n?m(20kg?cm) size 13 2n?m(20kg?cm) table 3 cable end processing dimensions size dimension c for hr10 dimension d for hr10a solder type crimp type size 7 5.5 or less 10 15-20 size 10 7 or less 16 15-20 size 13 CC 26 26 hr10 type hr10a type 1 use cables with a nominal sectional area of 0.129 mm 2 (awg#26) at the fnish outside diameters applicable for each size. 2 after processing the cable ends according to the dimensions in the above drawings, ft the parts to the cable as shown in the drawings. fit the parts to the cable in the following order: tightener, clamp washer, and plug body. fit the parts to the cable in the following order: cord bushing and plug body. 3 (solder type) insert the p shell unit into the assembly tool stand and solder it. (crimp type) after crimping the appropriate crimp terminal to the cable core, insert the crimp terminal into the terminal hole in the p shell unit. 4 assemble the connector in the following steps. 1. screw the plug body into the thread in the p shell unit with the tightening force shown in table 1 using a torque wrench with a fxed torque. before tightening the plug body,slacken part c so that no load is applied to the soldered wires. 2. apply the clamp washer to the bifurcated part of the plug body, and then tighten the tightener until surface b touches the plug body surface a. 1. fix by caulking the clamp accompanying the cable with the cable crimping tool(hr10a-tc-02) 2. screw the plug body into the thread in the p shell until with a tightening force shown in table 1 using a torque wrench with a fxed torque. before tightening the plug body, slacken the part d so that no load is applied to the soldered wires. 3. tighten the set screw so that the tip of the screw presses one of the two bosses on the clamp. fix the set screw with a tightening torque of 0.3n(3kg?cm) 4.attach the cord bushing to the plug body. 5 this completes the work. for any question on using the plugs, contact our sales or engineering department. remarks : loctite 242, henkel japan or equivalent is recommend to prevent the male thread section of the p shell unit and the set screw for loosing. p shell unit c plug body clamp washer tightener spanner jaw distance cable about 2 bifurcated part face a face b p shell unit clamp plug body boss set screw cable spanner jaw distance cord bushing d 2 or more a about 2 for solder type 2 for crimp type 0 -0.5 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 197 hr10 seriespush-pull connectors connector notes 1 : when using a plug with male terminal, be sure to use a receptacle or jack ftted with female terminal. 2 : standard fnish of the terminal is gold plating for the hr10, and silver plating for the hr10a and hr10g. be sure to use male and female connectors of the same plating. male pin side female pin side (hr10 type plug) (hr10 type jack) (hr10b type receptacle) (hr10a- [ ] t type receptacle) (hr10a- [ ] t type jack) (hr10a type jack) (hr10 ? hr10a hr10g type receptacle) (hr10a type plug) (hr10b type plug) (hr10a- [ ] t type plug) t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 198 hr10 seriespush-pull connectors recommended mounting hole mounting hole dimension shown here is tight by hexagon nut from back side. precautions 1. switch off the power of the circuit before disconnecting or plugging-in the connector. 2. use a connector with socket contacts at the power side of the circuit. 3. make sure that the coupling is in completely cocked position. 4. the cable pull and twisting strength and other characteristics may differ, deponding on the cable structure. please confirm vefore the use. 7 size 10 size 13 size a 1.6 2.6 2.6 b 5.1 6.6 8.6 c 8.1 11.1 14.5 panel thickness 0.7~2 0.7~2 0.8~1.5 shell size map mark +0.1 0 +0.1 0 +0.1 0 +0.1 0 +0.1 0 +0.1 0 +0.1 0 +0.1 0 +0.1 0 contact arrangement shell size 7 size 10 size contact arrangement no. of pins 4 5 6 10 12 withstanding voltage ac500v for a minute ac300v for a minute ac300v for a minute current rating 2a 2a 2a insulation resistance min 1,000m? min 1,000m? min 1,000m? contact resistance max 10m? max 10m? max 10m? solder pot inside dia. ?0.8 ?0.8 ?0.8 shell size 10 size 13 size contact arrangement no. of pins 10+coaxial contact 20 withstanding voltage ac300v for a minute ac300v for a minute current rating 2a 2a insulation resistance min 1,000m? min 1,000m? contact resistance max 10m? max 10m? solder pot inside dia. - ?0.8 note 1. the contact arrangement shown here is the mating surface of socket insert assembled in a receptacle. 2. the withstanding voltage shown here is test voltage value. 3. the isulation resistance value is measured at dc100v. 4. the contact resistance value is measured at dc1a. t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . |
Price & Availability of HR10A-10R-10PC71
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |