HA13007 quad driver ade-207-205 (z) 1st edition july 1, 1996 description the HA13007 monolithic, bipolar, high-voltage, high-current quad driver is especially designed for switching applications. this device is recommended for interfacing low-level logic to peripheral loads such as relays, solenoids, stepping motors, led, heaters, and other similar high-voltage, high-current loads. features guaranteed minimum output breakdown of 60 v, and maximum output current of 0.7 a low output collector-emitter saturation voltage input compatible with ttl, lsttl and 5 v cmos. integral transient suppression diodes for inductive loads lower input current truth table enable in out hh l hl h lxh note: h = high level: 2.0 v l = low level: 0.8 v x = don't care
HA13007 2 pin arrangement 16 8 7 6 5 4 3 2 1 in a in b enable gnd gnd gnd gnd vcc in c in d out d out c clamp out b clamp out a (top view) 15 14 13 12 11 10 9 absolute maximum ratings (ta = 25 c) item symbol rating unit notes supply voltage v cc 7.0 v 1 input voltage v in 0 to v cc v output voltage v cex 60 v output current i out 0.7 a power dissipation p t 1.85 w thermal resistance/junction-case q jc 15 c/w 2 thermal resistance/junction-ambient q ja 60 c/w 2 junction temperature tj 150 c operating junction temperature range tjop C40 to +125 c storage temperature range tstg C55 to +125 c notes: 1. recommended operating voltage v cc = 4.75 to 5.5 v 2. thermal resistances are as follows: q j-a1 60 c/w (soldered on a print circuit board) q -a2 35 c/w (soldered on a print circuit board with copper sufficiently) q j-a3 15 c/w (soldered on pins 4, 5, 12, and 13 with an infinite heat sink)
HA13007 3 electrical characteristics (ta = 25 c, v cc = 5.5 v) item symbol min typ max unit test conditions output leakage current i cex 100 m av ce = 60 v, v in = 0.8 v output sustaining voltage v ce(sus) 60 v v in = 0.8 v, ic = 100 ma output saturation voltage v ce(sat) 0.3 0.5 v v cc = 4.75 v, v in = 2.0 v, ic = 0.4 a 0.5 0.7 v v cc = 4.75 v, v in = 2.0 v, ic = 0.7 a input low voltage v il 0.8 v input low current i il C1 10 m av in = 0.8 v, ic = 0 input high voltage v ih 2.0 v input high current i ih 0 10 m a ic = 0.7 ax4, v in = 2.0 v 1.0 ma ic = 0.7 ax4, v in = 5.0 v supply current (all outputs on) is 50 65 ma ic = 0.7 ax4, v in = 5.5 v (all inputs) supply current (all outputs off) iso 8.0 ma v in = 0.8 v (all inputs) clamp diode leakage current i r 100 m av r = 60 v clamp diode forward voltage v f 1.2 1.6 v v in = 0.8 v, i f = 1.0 a 1.3 2.0 v v in = 0.8 v, i f =1 .5 a turn-on delay t plh 1.0 m s turn-off delay t phl 0.3 m s
HA13007 4 output saturation voltage vs. output current vcc = 4.75 v v = 2.0 v 0 0.2 0.4 0.6 0.8 0.2 0.4 0.6 ta = +85?c +25?c e40?c collector to emitter saturation voltage v (v) ic (a) ce(sat) in output saturation voltage vs. ambient temperature
HA13007 5 vcc = 4.75 v v = 2.0 v ic = 0.7 a e40 040 80 0 0.2 0.4 0.6 0.8 collector to emitter saturation voltage v (v) ce(sat) ambient temperature ta ( c) in output current vs. supply voltage v = 2.0 v ic = 0.7 a ta = 25?c 60 40 20 0 2.0 4.0 6.0 supply current is (ma) supply voltage vcc (v) all low 2 v x 1ch 2 v x 2ch 2 v x 3ch v = 2 v x 4ch in in stepping motor driver application
HA13007 6 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 motor coil 35 v max 0.1 f 4.75 to 5.5 v 1 2 enable 3 4 m f f f f 35 v max
HA13007 7 package dimensions 20.32 max 6.9 max 19.3 16 9 8 1 1.3 7.62 0.30 + 0.08 ?0.05 2.54 0.25 0.48 0.10 0.38 min 3.18 min 5.06 max 6.20 0 ?15 1.27 max hitachi code jedec eiaj weight (reference value) dp-16c conforms conforms 0.90 g unit: mm
HA13007 8 when using this document, keep the following in mind: 1. this document may, wholly or partially, be subject to change without notice. 2. all rights are reserved: no one is permitted to reproduce or duplicate, in any form, the whole or part of this document without hitachis permission. 3. hitachi will not be held responsible for any damage to the user that may result from accidents or any other reasons during operation of the users unit according to this document. 4. circuitry and other examples described herein are meant merely to indicate the characteristics and performance of hitachis semiconductor products. hitachi assumes no responsibility for any intellectual property claims or other problems that may result from applications based on the examples described herein. 5. no license is granted by implication or otherwise under any patents or other rights of any third party or hitachi, ltd. 6. medical applications: hitachis products are not authorized for use in medical applications without the written consent of the appropriate officer of hitachis sales company. such use includes, but is not limited to, use in life support systems. buyers of hitachis products are requested to notify the relevant hitachi sales offices when planning to use the products in medical applications. hitachi, ltd. semiconductor & ic div. nippon bldg., 2-6-2, ohte-machi, chiyoda-ku, tokyo 100, japan tel: tokyo (03) 3270-2111 fax: (03) 3270-5109 for further information write to: hitachi america, ltd. semiconductor & ic div. 2000 sierra point parkway brisbane, ca. 94005-1835 u s a tel: 415-589-8300 fax: 415-583-4207 hitachi europe gmbh electronic components group continental europe dornacher strae 3 d-85622 feldkirchen m?nchen tel: 089-9 91 80-0 fax: 089-9 29 30 00 hitachi europe ltd. electronic components div. northern europe headquarters whitebrook park lower cookham road maidenhead berkshire sl6 8ya united kingdom tel: 0628-585000 fax: 0628-778322 hitachi asia pte. ltd. 16 collyer quay #20-00 hitachi tower singapore 0104 tel: 535-2100 fax: 535-1533 hitachi asia (hong kong) ltd. unit 706, north tower, world finance centre, harbour city, canton road tsim sha tsui, kowloon hong kong tel: 27359218 fax: 27306071 copyright ? hitachi, ltd., 1997. all rights reserved. printed in japan.
|
