250 mw lower s - band fm transmitter, 2.2 - 2.3 ghz ma05935 - xx outline drawing 1,2,3 v 1p.00 preliminary f eatures fm transmitter with pll, vco and pa devices 3 volt operation parallel hard - wired frequency selection choice of 16 frequ ency channels @ 1mhz spacing high saturated output power: 24 dbm typ. 50 w input/output matched irig 106 - 00 compliant statek cr ystal oscillator high shock description m/a - com?s ma05935 is a miniature, phase - locked, fm transmitter module. the ma05935 is i deally suited for rugged telemetry systems. the ma05935 contains a shock hardened crystal oscill a- tor, a 0.35 m m cmos silicon phase - locked loop, and an ingap hbt vco and power amplifier, with supply line bypassing. the module r equires only a single, positive regulated 3vdc power supply. the ma05935 has fully matched (50 w ) input and output networks. m/a - com's ma05935 is fabricated on standard fr - 4 pc board material, employing automatic assembly of the hybrid technology componen ts (silicon cmos, ingap hbt, and smt). when fully encapsulated, this module will easily survive high shock pulses greater than 30,000g. this product is 100% rf tested to ensure co m- pliance to performance specifications. electrical specifications : vcc = +3v, zo = 50 ohms, t a = 25 c parameter test conditions frequency units min typ max supply voltage ?? ?? volts 2.85 ? 3.15 supply current ?? 2.2 - 2.3 ghz ma ? 350 typ. ? output power ?? 2.2 - 2.3 ghz dbm ? 24 typ. ? output vswr ?? 2.2 - 2.3 ghz ? < 2:1 ? stability - 40 c to +85 c 2.2 - 2.3 ghz % ? 0.0002 ? lock time ?? 2.2 - 2.3 ghz ms ? < 20 0.4 harmonics ?? 2.2 - 2.3 ghz dbc ? < - 25 0.8 output power vs. temp - 40 c to +85 c 2.2 - 2.3 ghz dbm 0.6 phase noise ?? 2.2 - 2.3 ghz dbc @50khz ? - 85 typ. ? power added efficency ?? 2.2 - 2.3 ghz % ? 23 typ. ? 1. module diameter = 1.125? 2. module height = 0.2? 3. module weight = 3 grams typical
250 mw lower s - band phase - locked fm transmitter ma05935 - xx v 1p.00 m/a - com inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein w ithout notice. m/a - com makes no warranty, representation, or guarantee regarding the suitability of its products fo r any particular purpose, nor does m/a - com assume any liability whatsoever arising out of the use or application of an y product(s) or information. visit www.macom.com for additional data sheets and product information. n north america: tel. (978) 656 - 2693 n asia/pacific: tel.+ 81 - 44 - 844 - 8296 , fax + 81 - 44 - 844 - 8298 n europe: tel. +44 (1344) 869 595, fax+44 (1344) 300 020 2 absolute maximum ratings 4,5 4. operation of this device above any one of these parameters may cause permanent damage. 5. adequate heat sinking and grounding requi red. parameter absolute maximum input power +13 dbm v cc +12 volts v bb - 8 volts to +6 volts i cc 600 ma max. dissipation power 1350 mw channel temperature +150c operating temperature 0c to +60c storage temperature - 65c to +150c h andling permanent damage to the ma05935 may occur if the following precautions are not adhered to: a. static sensitivity ? all d ie handling equipment and personnel should comply with dod - std - 1686 class i. b. transients ? avoid instruments and power supply transients while bias is connected to the ma05935. use shielded signal and bias cables to minimize inductive pick - up. mounting do not expose the ma05935 to temperatures greater than 180 c for more than 20 seconds. higher temperatures may result in reflow of the sn63/pb37 solder used for smt comp o- nent attach. typical bias configuration 6,7 6. apply +3 volts v cc . apply v mod . 7. v cc bypassing is performed on board. v cc ma05935-xx rf out v mod locked ref_out module outline rf shield 225 5.7 180 4.6 4 19 10.6 51 1.3 all dimensions are mils mm 155 3.9 90 2.3 100 2.54 all dimensions are mils mm board size is 1.125? diameter x 0.2? height (28.6mm diameter x 6mm height) - 390 9.9 - 490 12.5 - 440 11.2 - 340 8.6 - 390 9.9 - 440 11.2 - 490 12.5 - 340 8.6 446 11.33 396 10.1 496 12.6 - 50 1.3 0 50 1.3 - 25 .88 25 .88 1120 diameter (flat section to flat section) 28.45 1125 diameter (of round board) 28.6 0,0 - 288 7.3 288 7.3 - 438 11.3 438 11.3 438 11.3 - 438 11.3
250 mw lower s - band phase - locked fm transmitter ma05935 - xx v 1p.00 m/a - com inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein w ithout notice. m/a - com makes no warranty, representation, or guarantee regarding the suitability of its products fo r any particular purpose, nor does m/a - com assume any liability whatsoever arising out of the use or application of an y product(s) or information. visit www.macom.com for additional data sheets and product information. n north america: tel. (978) 656 - 2693 n asia/pacific: tel.+ 81 - 44 - 844 - 8296 , fax + 81 - 44 - 844 - 8298 n europe: tel. +44 (1344) 869 595, fax+44 (1344) 300 020 3 spurious emissions lock time stability (y - axis displays + 0.002% of lock freq) typical performance curves spurious emissions frequency vs tune voltage saturated output power vs. ghz 2.268 2.26575 2.2635 2.26125 2.259 2.25675 2.2545 2.25225 2.25 softplot measurement presentation trace a start: -20.650287 ps stop: 9.999990 ms 1 ghz 2.255546 2.25553475 2.2555235 2.25551225 2.255501 2.25548975 2.2554785 2.25546725 2.255456 softplot measurement presentation trace a start: -41.3006 ps stop: 20.0000 ms 1 2.150 2.170 2.190 2.210 2.230 2.250 2.270 2.290 2.310 2.330 0 0.5 1 1.5 2 2.5 3 control voltage (v) frequency (ghz) phase noise - 130 - 120 - 110 - 100 - 90 - 80 - 70 - 60 - 50 1.00e+03 1.00e+04 1.00e+05 1.00e+06 1.00e+07 offset frequency phase noise (dbc/hz) dbm 30 20 10 0 -10 -20 -30 -40 -50 -60 -70 softplot measurement presentation trace a start: 2.230493 ghz stop: 2.280493 ghz res bw: 100 khz vid bw: 1 khz sweep: 1 s 8/13/01 4:15:14 hp8563e module2_130801.spt 1-1 2-1 dbm 30 20 10 0 -10 -20 -30 -40 -50 -60 -70 softplot measurement presentation trace a start: 2.252993 ghz stop: 2.257993 ghz res bw: 30 khz vid bw: 100 hz sweep: 4 s 8/13/01 4:03:08 hp8563e module~1.spt 1 2-1
250 mw lower s - band phase - locked fm transmitter ma05935 - xx v 1p.00 m/a - com inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein w ithout notice. m/a - com makes no warranty, representation, or guarantee regarding the suitability of its products fo r any particular purpose, nor does m/a - com assume any liability whatsoever arising out of the use or application of an y product(s) or information. visit www.macom.com for additional data sheets and product information. n north america: tel. (978) 656 - 2693 n asia/pacific: tel.+ 81 - 44 - 844 - 8296 , fax + 81 - 44 - 844 - 8298 n europe: tel. +44 (1344) 869 595, fax+44 (1344) 300 020 d c connector the dc connector of the ma05935 - xx is a standard dual body 0.050? (1.27mm) pitch, 8 - pin header connector. the pin as signments of this connector are shown below. the through - hole connector was chosen to a l- low freedom in mounting; this connector may be either placed or omitted to allow use of other connector types. the dc connector provided with the ma05935 is supplied unattached to the board. rf connector the rf connector is a standard - sized, through - hole mounted connector. to afford user flexibility, the rf connector provided with the ma05935 is supplied unattached to the board. c hannel selection the pll determines the frequency of operation of the board. the channels available are listed in the following tables. there are 16 frequencies available, at 1mhz spacing. the channel selection on the board is performed through the use of 0402 smt zero ohm resistors, connected to the parallel input lines of the pll. co n- figuration pads to these lines are located to the right of the rf connector, when the board is oriented with the dc connector i n the lower part of the board, and rf connector in the upper part (see figure below t a- ble on following page). the following table (table 1) details the frequency choices, and the required resistor positions. for a zero (0) value, the resistor must be loaded hor i- zontally (that is, between the common smt pad and gnd), and for a value of high (1), the zero ohm r e- si s tor must be loaded vertically (i.e., between the common smt pad and vdd). application notes dc connector pinout dc connection (gnd pins are grey) gnd vdd vdd ref_out gnd locked gnd v_mod 4
250 mw lower s - band phase - locked fm transmitter ma05935 - xx v 1p.00 m/a - com inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein w ithout notice. m/a - com makes no warranty, representation, or guarantee regarding the suitability of its products fo r any particular purpose, nor does m/a - com assume any liability whatsoever arising out of the use or application of an y product(s) or information. visit www.macom.com for additional data sheets and product information. n north america: tel. (978) 656 - 2693 n asia/pacific: tel.+ 81 - 44 - 844 - 8296 , fax + 81 - 44 - 844 - 8298 n europe: tel. +44 (1344) 869 595, fax+44 (1344) 300 020 table 1 frequency selection for s lower band part number cs3 (r4=0 w ) cs2 (r3=0 w ) cs1 (r17=0 w ) cs0 (r13=0 w ) s lower band frequency ma05935 - 01 0 v 0 v 0 v 0 v 2.2405 ghz ma05935 - 02 0 v 0 v 0 v 3 v 2.2415 ghz ma05935 - 03 0 v 0 v 3 v 0 v 2.2425 ghz ma05935 - 04 0 v 0 v 3 v 3 v 2.2435 ghz ma05935 - 05 0 v 3 v 0 v 0 v 2.2445 ghz ma05935 - 06 0 v 3 v 0 v 3 v 2.2455 ghz ma05935 - 07 0 v 3 v 3 v 0 v 2.2465 ghz ma05935 - 08 0 v 3 v 3 v 3 v 2.2475 ghz ma05935 - 09 3 v 0 v 0 v 0 v 2.2485 ghz ma05935 - 10 3 v 0 v 0 v 3 v 2.2495 ghz ma05935 - 11 3 v 0 v 3 v 0 v 2.2505 ghz ma05935 - 12 3 v 0 v 3 v 3 v 2.2515 ghz ma05935 - 13 3 v 3 v 0 v 0 v 2.2525 ghz ma05935 - 14 3 v 3 v 0 v 3 v 2.2535 ghz ma05935 - 15 3 v 3 v 3 v 0 v 2.2545 ghz ma05935 - 16 3 v 3 v 3 v 3 v 2.2555 ghz resistors r4, r3, r17, r13(lsb) are zero ohm resistors for channel select bits channel select configuration of zero ohm resistors for frequency selection ma05935-14 2253.5mhz ma05935-16 2255.5mhz ma05935-13 2252.5mhz ma05935-15 2254.5mhz MA05935-09 2248.5mhz ma05935-10 2249.5mhz ma05935-11 2250.5mhz ma05935-12 2251.5mhz ma05935-05 2244.5mhz ma05935-06 2245.5mhz ma05935-07 2246.5mhz ma05935-08 2247.5mhz ma05935-01 2240.5mhz ma05935-02 2241.5mhz ma05935-03 2242.5mhz ma05935-04 2243.5mhz 5
250 mw lower s - band phase - locked fm transmitter ma05935 - xx v 1p.00 m/a - com inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein w ithout notice. m/a - com makes no warranty, representation, or guarantee regarding the suitability of its products fo r any particular purpose, nor does m/a - com assume any liability whatsoever arising out of the use or application of an y product(s) or information. visit www.macom.com for additional data sheets and product information. n north america: tel. (978) 656 - 2693 n asia/pacific: tel.+ 81 - 44 - 844 - 8296 , fax + 81 - 44 - 844 - 8298 n europe: tel. +44 (1344) 869 595, fax+44 (1344) 300 020 6 ordering information part no. description ma05935 - 01 24dbm module (operates at 2240.5mhz) ma05935 - 02 24dbm module (operates at 2241.5mhz) ma05935 - 03 24dbm module (operates at 2242.5mhz) ma05935 - 04 24dbm module (operates at 2243.5mhz) ma05935 - 05 24dbm module (operates at 2244.5mhz) ma05935 - 06 24dbm module (operates at 2245.5mhz) ma05935 - 07 24dbm module (operates at 2246.5mhz) ma05935 - 08 24dbm module (operates at 2247.5mhz) ma05935 - 09 24dbm module (operates at 2248.5mhz) ma05935 - 10 24dbm module (operates at 2249.5mhz) ma05935 - 11 24dbm module (operates at 2250.5mhz) ma05935 - 12 24dbm module (operates at 2251.5mhz) ma05935 - 13 24dbm module (operates at 2252.5mhz) ma05935 - 14 24dbm module (operates at 2253.5mhz) ma05935 - 15 24dbm module (operates at 2254.5mhz) ma05935 - 16 24dbm module (operates at 2255.5mhz)
|
