View T315HW04-V9_7698894.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 1 / 25 model name: t315hw04 v9 issue date : 2011/01/25 ()preliminary specifications ( )final specifications
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 2 / 25 contents no contents record of revisions 1 general description 2 absolute maximum ratings 3 electrical specification 3-1 electriacl characteristics 3-2 interface connections 3-3 signal timing specification 3-4 signal timing waveform 3-5 color input data reference 3-6 power sequence 4 optical specification 5 open cell drawing 6 reliability test items 7 packing 7-1 open cell shipping label 7-2 packing process 7-3 pallet and shipment information 8 precaution 8-1 mounting precautions 8-2 operating precautions 8-3 electrostatic discharge control 8-4 precautions for strong light exposure 8-5 storage 8-6 handling precautions for protect film
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 3 / 25 record of revision version date page description 0.0 2011/11/25 first release
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 4 / 25 1. general description this specification applies to the 31.5 inch color t ft-lcd skd model t315hw04 v9. this lcd open cell un it has a tft active matrix type liquid crystal panel 1 ,920x1,080 pixels, and diagonal size of 31.5 inch. this open cell unit supports 1,920x1,080 mode. each pixel is divid ed into red, green and blue sub-pixels or dots whic h are arranged in vertical stripes. gray scale or the bri ghtness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot. * general information items specification unit note active screen size 31.55 inch display area 698.4 (h) x 392.85 (v) mm outline dimension 717.585 (h) x 407.866 (v) x 1.81 (d) mm driver element a-si tft active matrix bezel opening 703.8(h) x 398.4 (v) mm display colors 8 bit, 16.7m colors number of pixels 1,920x1,080 pixel pixel pitch 0.36375 (h) x 0.36375 (w) mm pixel arrangement rgb vertical stripe display operation mode normally black surface treatment anti-glare, 3h haze=2%
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 5 / 25 2. absolute maximum ratings the followings are maximum values which, if exceede d, may cause faulty operation or damage to the unit item symbol min max unit conditions logic/lcd drive voltage vcc -0.3 14 [volt] note 1 input voltage of signal vin -0.3 4 [volt] note 1 operating temperature top 0 +50 [ o c] note 2 operating humidity hop 10 90 [%rh] note 2 storage temperature tst -20 +60 [ o c] note 2 storage humidity hst 10 90 [%rh] note 2 panel surface temperature pst 65 [ o c] note 3 note 1: duration:50 msec. note 2 : maximum wet-bulb should be 39 and no conde nsation. the relative humidity must not exceed 90% non-conde nsing at temperatures of 40 or less. at temperature s greater than 40 , the wet bulb temperature must not exceed 39 . note 3: surface temperature is measured at 50 dry condition
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 6 / 25 3. electrical specification the t315hw04 v9 open cell unit requires power input which is employed to power the lcd electronics and to drive the tft array and liquid crystal. 3.1 electrical characteristics 3.1.1: dc characteristics value parameter symbol min. typ. max unit note lcd power supply input voltage v dd 10.8 12 13.2 v dc power supply input curren i dd -- 0.74 0.82 a 1 power consumption p c -- 8.8 9.84 watt 1 inrush current i rush -- -- 4 a 2 input differential voltage O v id O 200 400 600 mv dc 3 differential input high threshold voltage v th +100 -- +300 mv dc 3 differential input low threshold voltage v tl -300 -- -100 mv dc 3 lvds interface input common mode voltage v icm 1.1 1.25 1.4 v dc 3 input high threshold voltage v ih (high) 2.7 -- 3.3 v dc 5 cmos interface input low threshold voltage v il (low) 0 -- 0.6 v dc 5
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 7 / 25 3.1.2: ac characteristics value parameter symbol min. typ. max unit note receiver clock : spread spectrum modulation range fclk_ss fclk -3% -- fclk +3% mhz 7 receiver clock : spread spectrum modulation frequency fss 30 -- 200 khz 7 lvds interface receiver data input margin fclk = 85 mhz fclk = 65 mhz trmg -0.4 -0.5 -- -- 0.4 0.5 ns 8 note : 1. v dd = 12.0v, fv = 60hz, fclk= 80mhz , 25 , test pattern : white pattern 2. measurement condition : rising time = 400us gnd gnd gnd gnd v vv v dd dddd dd 10% 90% 400 400400 400 s 3. v icm = 1.25v v t h v t l |v id | v ic m g n d 0 v |v id | |v id | l v d s - l v d s + 4. dcr interface: function table input output dcr_enable dim_in dim_out high pwm input dcr dimming out low pwm input pwm input nc nc keep high
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 8 / 25 note.(4-1) : during the deep duty control, partial darkness or c enter darkness might happen due to insufficient lamp current. note.(4-2): at low temperature, more warm up time may be needed . 5. the measure points of v ih and v il are in lcm side after connecting the system board a nd lcm. 6. input channel pair skew margin note: x = 0, 1, 2, 3, 4 7. lvds receiver clock sscg (spread spectrum clock gen erator) is defined as below figures 1 11 1/ // /f ff f ss ssss ss fclk fclk fclk fclk_ __ _ss ssss ss( (( (max max max max) )) ) fclk fclk fclk fclk_ __ _ss ssss ss( (( (min min min min) )) ) fclk fclk fclk fclk
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 9 / 25 8. receiver data input margin rating parameter symbol min type max unit note input clock frequency fclk fclk (min) -- fclk (max) mhz t=1/fclk input data position0 trip1 -|trmg| 0 |trmg| ns input data position1 trip0 t/7-|trmg| t/7 t/7+|trmg | ns input data position2 trip6 2t/7-|trmg| 2t/7 2t/7+|trmg| ns input data position3 trip5 3t/7-|trmg| 3t/7 3t/7+|trmg| ns input data position4 trip4 4t/7-|trmg| 4t/7 4t/7+|trmg| ns input data position5 trip3 5t/7-|trmg| 5t/7 5t/7+|trmg| ns input data position6 trip2 6t/7-|trmg| 6t/7 6t/7+|trmg| ns rx1 rx0 rx6 rx5 rx4 rx3 rx2 rx1 rx0 rx6 rx2 rx3 trip1 trip0 trip6 trip5 trip4 trip3 trip2 v vv v diff diff diff diff = = = = 0 00 0v vv v 1/fclk=t lvds-rx input clock lvds-rx input data
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 10 / 25 3.2 interface connections lcd connector: 187059-5122 (p-two, lvds connector) mating connector: 187087-51193 (p-two, use ffc cabl e) pin symbol description pin symbol description 1 gnd ground 26 gnd ground 2 nc no connection 27 gnd ground 3 nc auo internal use only 28 ch2_0- lvds channel 2, signal 0- 4 nc auo internal use only 29 ch2_0+ lvds channel 2, signal 0+ 5 nc no connection 30 ch2_1- lvds channel 2, signal 1- 6 nc auo internal use only 31 ch2_1+ lvds channel 2, signal 1+ 7 lvds_sel open/high(3.3v) for ns, low (gnd) for jeida 32 ch2_2- lvds channel 2, signal 2- 8 nc auo internal use only 33 ch2_2+ lvds channel 2, signal 2+ 9 nc auo internal use only 34 gnd ground 10 nc auo internal use only 35 ch2_clk- lvds channel 2, clock - 11 gnd ground 36 ch2_clk+ lvds channel 2, clock + 12 ch1_0- lvds channel 1, signal 0- 37 gnd ground 13 ch1_0+ lvds channel 1, signal 0+ 38 ch2_3- lvds channel 2, signal 3- 14 ch1_1- lvds channel 1, signal 1- 39 ch2_3+ lvds channel 2, signal 3+ 15 ch1_1+ lvds channel 1, signal 1+ 40 nc no connection 16 ch1_2- lvds channel 1, signal 2- 41 nc no connection 17 ch1_2+ lvds channel 1, signal 2+ 42 gnd ground 18 gnd ground 43 gnd ground 19 ch1_clk- lvds channel 1, clock - 44 gnd ground 20 ch1_clk+ lvds channel 1, clock + 45 gnd ground 21 gnd ground 46 gnd ground 22 ch1_3- lvds channel 1, signal 3- 47 nc no connection 23 ch1_3+ lvds channel 1, signal 3+ 48 v dd power supply, +12v dc regulated 24 nc no connection 49 v dd power supply, +12v dc regulated 25 nc no connection 50 v dd power supply, +12v dc regulated 51 v dd power supply, +12v dc regulated
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 11 / 25 lvds option = high/open ns b bb b 2 22 2 n a n an a n a d e d ed e d e d e d ed e d e b bb b 2 22 2 b bb b 3 33 3 b bb b 4 44 4 b bb b 5 55 5 n a n an a n a b bb b 3 33 3 r rr r 0 00 0 r rr r 5 55 5 g gg g 0 00 0 g gg g 0 00 0 r rr r 0 00 0 r rr r 1 11 1 r rr r 2 22 2 r rr r 3 33 3 r rr r 4 44 4 r rr r 1 11 1 g gg g 1 11 1 b bb b 0 00 0 b bb b 1 11 1 b bb b 1 11 1 g gg g 1 11 1 g gg g 2 22 2 g gg g 3 33 3 g gg g 4 44 4 g gg g 5 55 5 g gg g 2 22 2 c lo ck c lo ck c lo ck c lo ck c h x c h x c h x c h x _ __ _ 0 00 0 + ++ + c h x c h x c h x c h x _ __ _ 0 00 0 - -- - c h x c h x c h x c h x _ __ _ 1 11 1 + ++ + c h x c h x c h x c h x _ __ _ 1 11 1 - -- - c h x c h x c h x c h x _ __ _ 2 22 2 + ++ + c h x c h x c h x c h x _ __ _ 2 22 2 - -- - c h x c h x c h x c h x _ __ _ 3 33 3 + ++ + c h x c h x c h x c h x _ __ _ 3 33 3 - -- - r rr r 6 66 6 b bb b 7 77 7 n a n an a n a n a n an a n a r rr r 6 66 6 r rr r 7 77 7 g gg g 6 66 6 g gg g 7 77 7 b bb b 6 66 6 r rr r 7 77 7 p re vio u s c y cle c u rre n t c yc le n e xt c yc le p re vio u s c y cle c u rre n t c yc le n e xt c yc le p re vio u s c y cle c u rre n t c yc le n e xt c yc le p re vio u s c y cle c u rre n t c yc le n e xt c yc le note: x = 1, 2, 3, 4? lvds option = low jeida b bb b 4 44 4 n a n an a n a d e d ed e d e d e d ed e d e b bb b 4 44 4 b bb b 5 55 5 b bb b 6 66 6 b bb b 7 77 7 n a n an a n a b bb b 5 55 5 r rr r 2 22 2 r rr r 7 77 7 g gg g 2 22 2 g gg g 2 22 2 r rr r 2 22 2 r rr r 3 33 3 r rr r 4 44 4 r rr r 5 55 5 r rr r 6 66 6 r rr r 3 33 3 g gg g 3 33 3 b bb b 2 22 2 b bb b 3 33 3 b bb b 3 33 3 g gg g 3 33 3 g gg g 4 44 4 g gg g 5 55 5 g gg g 6 66 6 g gg g 7 77 7 g gg g 4 44 4 c lo ck c lo ck c lo ck c lo ck r rr r 0 00 0 b bb b 1 11 1 n a n an a n a n a n an a n a r rr r 0 00 0 r rr r 1 11 1 g gg g 0 00 0 g gg g 1 11 1 b bb b 0 00 0 r rr r 1 11 1 c h x c h x c h x c h x _ __ _ 0 00 0 + ++ + c h x c h x c h x c h x _ __ _ 0 00 0 - -- - c h x c h x c h x c h x _ __ _ 1 11 1 + ++ + c h x c h x c h x c h x _ __ _ 1 11 1 - -- - c h x c h x c h x c h x _ __ _ 2 22 2 + ++ + c h x c h x c h x c h x _ __ _ 2 22 2 - -- - c h x c h x c h x c h x _ __ _ 3 33 3 + ++ + c h x c h x c h x c h x _ __ _ 3 33 3 - -- - p re vio u s c yc le c u rre n t c ycle n e x t c ycle p re vio u s c yc le c u rre n t c ycle n e x t c ycle p re vio u s c yc le c u rre n t c ycle n e x t c ycle p re vio u s c yc le c u rre n t c ycle n e x t c ycle note: x = 1, 2, 3, 4? g7
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 12 / 25 3.3 signal timing specification this is the signal timing required at the input of the user connector. all of the interface signal tim ing should be satisfied with the following specifications for its proper operation. timing table (de only mode) signal item symbol min. typ. max unit period tv 1090 1125 1480 th active tdisp (v) 1080 th vertical section blanking tblk (v) 10 45 400 th period th 1030 1100 1325 tclk active tdisp (h) 960 tclk horizontal section blanking tblk (h) 70 140 365 tclk clock frequency fclk=1/tclk 50 74.25 82 mhz vertical frequency frequency fv 47 60 63 hz horizontal frequency frequency fh 60 67.5 73 khz notes: (1) display position is specific by the rise of de signal only. horizontal display position is specified by the ris ing edge of 1 st dclk after the rise of 1 st de, is displayed on the left edge of the screen. (2)vertical display position is specified by the ri se of de after a ?low? level period equivalent to e ight times of horizontal period. the 1 st data corresponding to one horizontal line after th e rise of 1 st de is displayed at the top line of screen. (3)if a period of de ?high? is less than 1920 dclk or less than 1080 lines, the rest of the screen dis plays black. (4)the display position does not fit to the screen if a period of de ?high? and the effective data per iod do not synchronize with each other.
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 13 / 25 3.4 signal timing waveforms th tdisp(v) tblk(v) tv de rgb data line n invalid data invalid data line 1 line 2 line 3 line n line 4 tclk clk de ch1 ch2 pixel m-7 pixel m-5 pixel m-3 pixel m-1 pixel m-6 pixel m-4 pixel m-2 pixel m invalid data invalid data pixel 1 pixel 2 pixel 3 pixel 5 pixel 4 pixel 6 pixel 7 pixel 8 pixel 9 pixel 10 pixel 11 pixel 12 pixel m-5 pixel m-3 pixel m-1 pixel m-4 pixel m-2 pixel m invalid data invalid data pixel 1 pixel 2 pixel 3 pixel 4 th tdisp(h) tblk(h) m m m m p p p p i i i i x x x x e e e e l l l l n l in e n l in e n l in e n l in e
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 14 / 25 3.5 color input data reference the brightness of each primary color (red, green an d blue) is based on the 8 bit gray scale data input for the color; the higher the binary input, the brighter the color . the table below provides a reference for color ve rsus data input. color data reference input color data red msb lsb green msb lsb blue msb lsb color r7 r6 r5 r4 r3 r2 r1 r0 g7 g6 g5 g4 g3 g2 g1 g0 b7 b6 b5 b4 b3 b2 b1 b0 black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 basic color white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ---- red(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 r red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 ---- green(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 g green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 ---- blue(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 b blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 15 / 25 3.6 power sequence for lcd values parameter min. type. max. unit t1 0.4 --- 30 ms t2 0.1 --- 50 ms t3 450 --- --- ms t4 0 *1 --- --- ms t5 0 --- --- ms t6 --- --- --- *2 ms t7 500 --- --- ms t8 10 --- 50 ms t9 0 --- --- ms note: (1) t4=0 : concern for residual pattern before blu turn off. (2) t6 : voltage of vdd must decay smoothly after p ower-off. (customer system decide this value) pow er supply for lcd pow er supply for lcd pow er supply for lcd pow er supply for lcd vd d vd d vd d vd d (+ (+(+ (+ 12 1212 12 v vv v ) )) ) interface signal interface signal interface signal interface signal ( (( (lv ds data lv ds data lv ds data lv ds data & & & & clk clk clk clk ) )) ) backlight on backlight on backlight on backlight on / // /off offoff off control signal control signal control signal control signal ( (( (vblo n vblo n vblo n vblo n ) )) ) t1 10% 90% t3 t4 t5 t6 10% 90% 10% t7 g nd g nd valid d ata valid d ata valid d ata valid d ata t2 g n d cm o s interface signal cm o s interface signal cm o s interface signal cm o s interface signal g nd t8 t9 (lvds_sel?)
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 16 / 25 4. optical specification optical characteristics are determined after the un it has been ?on? (note 1.) and stable for approxima tely 45 minutes in a dark environment at 25c. the values s pecified are at an approximate distance 50cm from t he lcd surface at a viewing angle of and equal to 0. fig.1 presents additional information concerning th e measurement equipment and method. values parameter symbol min. typ. max unit notes contrast ratio cr 3200 4000 -- 1 surface luminance (white) l wh 320 400 -- cd/m 2 2 luminance variation white(9p) -- -- 1.33 3 response time (g to g) t -- 8 -- ms 4 color gamut ntsc 72 % color coordinates red r x 0.640 r y 0.330 green g x 0.281 g y 0.590 blue b x 0.144 b y 0.060 white w x 0.28 w y typ.-0.03 0.29 typ.+0.03 viewing angle 5 x axis, right( =0) r -- 89 -- degree x axis, left( =180) l -- 89 -- degree y axis, up( =90) u -- 89 -- degree y axis, down ( =270) d -- 89 -- degree sr3 or equivalent
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 17 / 25 note: 1. all above optical specifications are defined by t315hw04 v9 module basis. 2. contrast ratio (cr) is defined mathematically as : surface luminance of l on5 contrast ratio= surface luminance of l off5 2. surface luminance is luminance value at point 5 across the lcd surface 50cm from the surface with a ll pixels displaying white. from more information see fig 2. when lamp input v ddb =24v, i ddb = 2.79ma. l wh =lon5 where lon5 is the luminance with all pixels display ing white at center 5 location. 3. the variation in surface luminance, white is defined (center of screen) as: white(9p) = maximum(l on1 , l on2 ,?,l on9 )/ minimum(l on1 , l on2 ,?l on9 ) 4. response time t is the average time required for display transition by switching the input signal for five luminance ratio (0%,25%,50%,75%,100% brightness mat rix) and is based on f v =60hz to optimize. target measured response time 0% 25% 50% 75% 100% 0% 0% to 25% 0% to 50% 0% to 75% 0% to 100% 25% 25% to 0% 25% to 50% 25% to 75% 25% to 100% 50% 50% to 0% 50% to 25% 50% to 75% 50% to 100% 75% 75% to 0% 75% to 25% 75% to 50% 75% to 100% start 100% 100% to 0% 100% to 25% 100% to 50% 100% to 75% t is determined by 10% to 90% brightness difference of rising or falling period. (as illustrated) the response time is defined as the following figur e and shall be measured by switching the input sign al for ?any level of grey(bright) ? and ?any level of gray (dark)?. any level of gray (bright) any level of gr ay (dark) any level of gray (bright) t (r) 0%, 25%, 50%, 75%, 100% photodetector output time t (f) 0%, 25%, 50%, 75%, 100% 0%, 25%, 50%, 75%, 100% 100% 90% 10%
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 18 / 25 fig. 2 luminance 5. viewing angle is the angle at which the contrast ratio is greater than 10. the angles are determine d for the horizontal or x axis and the vertical or y axis wit h respect to the z axis which is normal to the lcd surface. for more information see fig3. fig.3 viewing angle 1 2 3 4 5 6 7 8 h v h/6 h/2 v/2 v/6
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 19 / 25 5. open cell drawing
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 20 / 25 6. reliability test items test item q?ty condition 1 high temperature storage test 3 60 , 300hrs 2 low temperature storage test 3 -20 , 300hrs 3 high temperature operation test 3 50 , 300hrs 4 low temperature operation test 3 -5 , 300hrs 5 vibration test (non-operation) 3 wave form: random vibration level : 1.5g rms bandwidth : 10-300hz duration : x,y,z 30min per axes x,y,z: horizontal, face up 6 shock test (non-operation) 3 shock level: 50g waveform: half since wave, 11ms direction: x, y, z, one time each direction 7 vibration test (with carton) 21 random wave (1.5g rms, 10-200hz) 30mins/ per each x,y,z axes 8 drop test (with carton) 21 height: 30.5 cm (astmd4169-i) 1 corner, 3 edges, 6 surfaces (refer astm d 5276) note: test item 1~4 ra tests are done on auo t315hw 04 v9 panels.
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 21 / 25 7. packing 7.1 open cell shipping label (35*7mm) 1. s/n number 2. grade 3. manufacture fab. 4. manufactured date 5. model name carton label: 7.2 packing process: t 315 hw0 4 v 9 9 1 . 31 t0 9 . 9 xx carton label location t315hw04 v9
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 22 / 25 1 package for 7+1 trays epe cushion carton bag epe cushion epe cushion tray cell step 2 7 full sets tray+1 empty tray step 1 3 pcs skd+4 pcs spacers of one tray *1 2 spacer 2 spacer *3 one pallet for 10 packages
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 23 / 25 7-3 pallet and shipment information specification item qty. dimension (mm) weight (kg) packing remark 1 packing box 21pcs/box 970(l)*588(w)*280(h) 37 2 pallet 1 1180(l)*980(w)*132(h) 15 3 boxes per pallet 10 boxes/pallet 4 panels per pallet 210pcs/pallet pallet after packing 210 1180(l)*980(w)*1532(h) 385
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 24 / 25 8. precautions please pay attention to the followings when you use this tft lcd module. 8-1 mounting precautions (1) you should consider the mounting structure so t hat uneven force (ex. twisted stress) is not applie d to the cell. and the frame on which a cell is mount ed should have sufficient strength so that external force is not transmitted directly to the cell. (2) please attach the surface transparent protectiv e plate to the surface in order to protect the pola rizer. transparent protective plate should have sufficient strength in order to the resist external force. (3) you should adopt radiation structure to satisfy the temperature specification. (4) acetic acid type and chlorine type materials fo r the cover case are not desirable because the form er generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break by electro-chemical reaction. (5) do not touch, push or rub the exposed polarizer s with glass, tweezers or anything harder than hb pencil lead. and please do not rub with dust clothe s with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cloth. (some cosmetics are detrimental to the polarizer.) (6) when the surface becomes dusty, please wipe gen tly with absorbent cotton or other soft materials like chamois soaks with petroleum benzene. normal-h exane is recommended for cleaning the adhesives used to attach front/ rear polarizers. do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (7) wipe off saliva or water drops as soon as possi ble. their long time contact with polarizer causes deformations and color fading. (8) do not open the case because inside circuits do not have sufficient strength. 8-2 operating precautions (1) the open cell unit listed in the product specif ication sheets was designed and manufactured for tv application (2) the spike noise causes the mis-operation of cir cuits. it should be lower than following voltage: v=200mv(over and under shoot voltage) (3) response time depends on the temperature. (in l ower temperature, it becomes longer.) (4) brightness depends on the temperature. (in lowe r temperature, it becomes lower.) and in lower temperature, response time (required time that brig htness is stable after turned on) becomes longer. (5) be careful for condensation at sudden temperatu re change. condensation makes damage to polarizer or electrical contacted parts. and after fading condensation, smear or spot will occur. (6) when fixed patterns are displayed for a long ti me, remnant image is likely to occur. (7) module has high frequency circuits. sufficient suppression to the electromagnetic interference sha ll be done by system manufacturers. grounding and shie lding methods may be important to minimize the interface. 8-3 electrostatic discharge control since a open cell unit is composed of electronic ci rcuits, it is not strong to electrostatic discharge . make certain that treatment persons are connected to gro und through wrist band etc. and don?t touch interface pin directly.
t315hw04 v9 skd product specification rev.00 ? copyright auo optronics corp. 2011 all rights res erved. page 25 / 25 8-4 precautions for strong light exposure strong light exposure causes degradation of polariz er and color filter. 8-5 storage when storing open cell units as spares for a long t ime, the following precautions are necessary. (1) store them in a dark place. do not expose the o pen cell unit to sunlight or fluorescent light. kee p the temperature between 5 and 35 at normal humidity. (2) the polarizer surface should not come in contac t with any other object. it is recommended that the y be stored in the container in which they were shipp ed. 8-6 handling precautions for protection film of pol arizer the protection film of polarizer is still attached on the surface as you receive open cell units. when the protection film is peeled off, static electrici ty is easily generated on the polarizer surface. th is should be peeled off slowly and carefully by people who ar e electrically grounded and with well ion-blown equipment or in such a condition, etc.

▲Up To Search▲

Price & Availability of T315HW04-V9

	To Download T315HW04-V9 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .