website: www.displaytech.com.hk product specifications n general specification n absolute maximum ratings n electrical characteristics n electro - optical characteristics n block diagram n mechanical d rawing n backlight drawing n backlight specification n quality guarantee n precautions for using lcd modules n using lcd modules n revision record contents in this document are subject to change without notice. no part of this document may be repro duced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of displaytech ltd. 15 april 2008.
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 2 of 18 n general specification item contents display format 32 x 128 dots dot size 0.242 x 0.245 view area 36.1 mm x 9.95mm module size 41.3 mm x 19.7mm x 8.1 mm lcd type fstn polarizer mode trans flective view angle 6 o clock backlight led backlight driver type external power backlight color rgb controller & lcd driver st7565v driving method 1/33 duty, 1/6 bias n absolute maximun ratings (ta=25 c vss=0v) item symbol min. typ. max. unit power supply for logic vdd - 0.3 --- 3.6 v power supply for lcd v0 - v ss 4.0 --- 13.0 v input voltage v in - 0.3 --- vdd+0.3 v supply voltage for led backlight v led --- 3. 2 --- v normal operating temperature top 0 --- 5 0 c normal storage temperature tst - 1 0 --- 6 0 c wide operating temperature top - 20 --- 70 c wide storage temperature tst - 30 --- 80 c n electrical characteristics (ta=25 c, vdd= 3.0 v 5% ) item symbol condition min. typ. max. unit power supply for lcm vdd --- 2.85 3.0 3.15 volt input voltage v il l level vss --- 0. 2 vdd volt v ih h level 0. 8 vdd --- vdd volt lcd driver driving voltage vdd2 --- --- --- --- volt 25 c --- 6 .9 --- --- --- --- --- supply current for lcm idd vdd= 3 . 0 v --- 0.35 --- ma ie * --- --- --- --- iled vled=3. 2 v --- 60 ---
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 3 of 18 n electro - optical characteristics no item symbol measuring condition std.value unit remark c min typ max 1 reco mmended operating voltage vlcd ? = 0 = 0 25 6.6 6.9 7.2 v note1 note2 2 operating voltage vth ? = 0 = 0 0 --- --- --- 25 --- 1.8 8 9 --- 50 --- --- --- vsat ? = 0 = 0 0 --- --- --- 25 --- 2. 116 --- 50 --- --- --- 3 re sponse time tr ? = 0 = 10 0 --- --- --- ms note4 25 --- 5 8 90 50 --- --- --- tf ? = 0 = 10 0 --- --- --- 25 --- 11 8 210 50 --- --- --- 4 viewing angle (cr 2) ? =0 25 --- 40 --- deg note1 ? =180 25 --- 35 --- ? =90 25 --- 30 --- ? =270 25 --- 30 --- 5 current consumption ilcd hz=64 25 --- 1 7 --- ua note3 note 1 : definition of viewing angle and direction note 2 : thershold voltage and saturation voltage vth: the voltage vop which the transmissi on rate of segment is 90%(positive) or 10%(negative) of saturated value on conditions of the selected waveform.(non - selected waveform is opposition) vsat: the voltage vop which the transmission rate of segment is 10%(positive) or 10%(negative) of saturated value on conditions of the selected waveform.(non - selected waveform is opposition) detector 3h =90 6h =0 z ? =0 9h =270 12h =180 ?
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 4 of 18 note 3 : current consumption (i lcd ) note 4 : response time (tr, tf) note 5 : contrast ratio (cr) 5.1 positive type: contrast ratio = brightness at vop(non - selected) b rightness at vop(selected) 5.2 negative type: contrast ratio = brightness at vop(selected) brightness at vop(non - selected) note 6 : capacitance (c) conditions: voltage applied to all segments. conditions: 1.driving waveform: stat ic waveform. 2.voltage applied to all segments
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 5 of 18 n block diagram
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 6 of 18 n mechancial drawing
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 7 of 18 n backlig ht drawing
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 8 of 18 n backlight specification mechanical specifications item nominal dimensions unit outline size (lxwxh) 41.3 x 19.7 x 8. 1 0 mm viewing area (lxw) 37.10 x 10.95 mm contact pin pitch/length nil mm no.of led smt 3 --- electrical/o ptical characteristics (t a =25 c, i f = 60 ma typ.) mode parameter unit color red p ure green blue --- chromaticity coordinate x=0.7032 y=0.2965 x=0.1899 y=0.7276 x=0.1417 y=0.0612 --- forward voltage (vf) 3.2 typ 3.2 typ 3.2 typ v forward current (if) 60 60 60 ma average luminous intensity (iv) 62 336 134 cd/ m 2 absolute maximum rating item red p ure green blue unit forward current 9 0ma 9 0ma 9 0ma if reverse voltage 5 v 5 v 5 v vr power dissipation 288 mw 288 mw 288 mw pd operating temperature - 20 c to 70 c top storage temperature - 30 c to 80 c tstg testing point circuit diagram remark: 1. average luminous intensity is the average value of the six in dicated points as shown . 2. measure ment instrument: bm - 7, aperture: ? 10mm .
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 9 of 18 n quality guarantee pur po se: it is to define the inspection standard of lcd modules product standar d 1) inspection and test function test appearance inspection packing specifiction 2) inspection condit ion put under the lamp (20w 2) at a distance 100mm from the lcd modules. tilt upright 45 degree by the front (back) to inspect lcd appearance . 3) aql inspection level sampling method : mil - std - 105d sampling plan : single major defect : 0.65% (major) m inor defect : 2.5% (minor) general level : ii/normal display area definition: lamp lcm operator viewing boundary view area
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 10 of 18 inspection standard 1 ) function al test standard i tem i n spection standard descri p tion s tandard defect type 1 lcd has no display reject maj 2 lcm display do not ch ange reject maj 3 display wrong pattern r eject maj 4 display segment open r eject maj 5 display dim segment r eject maj 6 wrong lcd view ing direction r eject maj 7 dim display see sample maj 8 lcd color variation see sample maj 9 patte rn parallelism acceptable range l 0.25 1 accept < 4 1 w 1 accept > 4 1 w 1 reject min missing segment missing segment dim segment dim segment
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 11 of 18 i tem i n spection standard descri p tion s tandard defect type 11 lcd display broken segment(dots) draw standard x y qty R 4 1 b R 4 1 a 1 reject min (x or y) R 0.2mm 1 reject min Q 4 1 b Q 4 1 a 1 accept Q 5 1 b Q 5 1 a 2 accept 12 lcd display black spot or white spot = 2 y x + qty <0.10 accept 0.1< Q 0.20 2 accept 0.20 Q <0.25 1 accept 0.25< Q 0.4 0 reject min >0.4 0 reject maj 13 lcd display excess black line or white line black line/white line(l w)mm qty (l Q 1.0) (w Q 0.025) 2 accept (1.01.5) (w Q 0.025) 0 rej ect min (l>2) (w>0.025) 0 reject maj 14 backlight not function reject maj 15 led not function or dim reject min 16 backlight defect (dirt, scratch) reject min 2 ) cosmetic inspection s tandard i tem standard description of inspection s tandard defec t type 1 lcd inspection item 1.1 lcd color variation see sample min 1. 2 lcd broken reject maj 1. 3 wrong polarizer of lcd reject maj 1. 4 spot on lcd surface reject maj 1. 5 scratch on lcd scratch = qty <0.1 except accept 0.1 Q Q 0.15 2 accept 0.15< Q 0.25 1 accept >0.25 1 reject min 1. 6 lcd scratch scratch depth see sample scratch =l scratch =w qty w Q 0.015 accept <0.5 w Q 0.02 2 accept <1.0 w Q 0.03 1 accept R 1.0 w R 0.03 1 reject min 1. 7 whit e or black spot on lcd = 2 y x + qty <0.1 accept 0.1 Q <0.2 2 accept 0.2 Q Q 0.25 1 accept >0.25 1 reject min bevy point - reject min = 2 y x + x y
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 12 of 18 i tem standard description of inspection s tandard defect type 1. 8 black line in lcd (l) (w) qty l Q 1.0 w Q 0.025 2 accept 1.0<1 Q 1.5 w Q 0.025 1 accept 1.50.025 1 reject min 1. 9 round air bubble size qty <0.15 2 accept 0.15 Q Q 0.25 1 accept >0.25 0 reject min 1.1 0 line defect (l) (w) qty l<0.5 w<0.02 2 accept l<1.0 w<0.03 1 accept l R 1.0 w R 0.3 0 reject min 1.1 1 finger print reject min 2 pcb/cob specification 2.1 pcb deformity l h Q 6.0mm Q 1.5mm accept >6.0mm Q 1.5mm reject min <6.0mm >1.5mm reject min >6.0mm >1. 5mm reject min 2.2 deformity at pcb edge, damage circuit. reject maj 2.3 convex at pcb edge l h Q 6.0mm Q 1.5mm accept >6.0mm Q 1.5mm reject min <6.0mm >1.5mm reject min >6.0mm >1.5mm reject min 2.4 damage excess 2 x 2mm at the pcb corner re ject min 2.5 scratch on pcb surface see sample min 2.6 scratch on pcb coat/leakage coat on pcb surface reject maj 2.7 open circuit reject maj 2.8 pcb pth open reject maj 2.9 repair pcb pth qty Q 2 pcs accept qty R 3 pcs reject maj 2.10 color different from one side to another side. reject min 2.11 repaired solder mask area Q 30mm 2 accept R 30mm 2 reject min 2.12 scratch circuit, damage circuit a Q 1/2w or b1/2w or b>w reject 3 bezel specification 3.1 wrong materials maj 3. 2 incorrect dimension maj 3.3 bezel broken maj 3.4 rust on bezel maj 3.5 hole or dirty on oil paint surface size cm 2 /per top surface Q 0.3 2 accept 0.3< Q 0.5 1 accept >0.5 0 reject min side Q 0.5 2 accept 0.5< Q 0 .8 1 accept >0.8 0 reject min
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 13 of 18 i tem standard description of inspection s tandard defect type 3.6 bezel bow or twist h Q 0.01 mm/mm accept h > 0.01 mm/mm reject min 3.7 d1 - d2 Q tolerance accept d1 - d2>tolerance reject min 3.8 scr atch on bezel face accept qty l w not defined see sample - w Q 0.15 l Q 3 w Q 0.20 2 l Q 2 w Q 0.3 2 - w>0.3 side accept qty l w see sample - w Q 0.2 except l Q 3 w Q 0.25 2 l Q 2 w Q 0.3 2 3.9 twist angle =45 +5 accept 3.10 void gap between bezel and pcb r eject min 3.11 bezel clip incorrectly reject min 4 solder specification 4.1 wrong component reject maj 4.2 broken component reject maj 4.3 mis - alignment component legs extend beyond the p ad and legs >pad distance(w) on solder area >w 2 accept component legs extend beyond the pad and legs >pad distance(w) on solder area 1/4w reject min 4.4 component assembly defect reject min 4.5 chip components hoist Q 0.5mm accept 4.6 chip components hoist>0.5mm reject min ng
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 14 of 18 i tem standard description of inspection s tandard defect type 4.7 components hoist h Q 2.0mm accept h>2 .0mm reject min 4.8 switch (socket) hoist h Q 0.5mm accept h>0.5mm reject min 4.9 components cold solder or incomplete solder reject maj 4.10 solder pad tilt up, but height (h) less than solder pad thickness (a) accept 4.11 excess solder abo ve components reject min 4.12 insufficient solder below components height or less than diameter reject min 4.13 solder area less than soldering pad area by 2/3 reject min 4.14 trimmed pin length beyond 0.09inch (2.3mm) reject min 5 p acking specification 5.1 wrong carton mark . reject maj 5.2 carton mark problem reject min 5.3 carton damage extend than 150mm reject maj 5.4 carton damage, scratch more 50mm, less 150mm. reject min
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 15 of 18 n p recautions for using lcd modules handling precautions 1. this device is susceptible to electro - static discharge (esd) damage. observe anti - static precautions. 2. the display panel is made of glass. do not subject it to a mechanical shock by dropping it or impact. 3. if the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in your mouth. if the substance contacts your skin or clothes, wash it off using soap and water. 4. do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 5. the polarizer covering the display surface of the lcd module is soft and easily scratched. handle this polarizer carefully. 6. if the display surface becomes contaminated, breathe on the surface and gently wipe it with a soft dry cloth. if it is heavily contaminated, moisten cloth with one of the following solvents : isopropyl alcohol ethyl alcohol 7. solvents other than those above - mentioned may damage the polarizer. especially, do not use the following. water ketone aromatic solvents 8. exercise care to minimize corrosion of the electrode. corrosion of the electrodes is accelerated by water droplets, moisture condensation or a current flow in a high - humidity environment. 9. install the lcd module by using the mounting holes . when mounting the lcd module make sure it is free of twisting, warping and distortion. in particular, do not forcibly pull or bend the i / o cable or the backlight cable. 10. do not attempt to disassemble or process the lcd module. 11. nc terminal should be open. do not connect anything. 12. if the logic circuit power is off, do not apply the input signals. 13. to prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. be sure to ground the body when handling the lcd m odules. tools required for assembling, such as soldering irons, must be properly grounded. to reduce the amount of static electricity generated, do not conduct assembling and other work under dry conditions. the lcd module is coated with a film to protect the display surface. exercise care when peeling off this protective film since static electricity may be generated. power supply precautions: 1. identify and, at all times, observe absolute maximum ratings for both logic and lc drivers. note that there is some variance between models. 2. prevent the application of reverse polarity to vdd and vss, however briefly. 3. use a clean power source free from transients. power - up conditions are occasionally jolting and may exceed the maximum ratings of the modules. 4. the vdd power of the module should also supply the power to all devices that may access the display. don t allow the data bus to be driven when the logic supply to the module is turned off. 5. do not install a capacitor between the vo (contrast) pin and ground. vdd must, at all times, exceed the vo voltage level. the capacitor combines with the contrast potentiometer to form an r - c network which holds - up vo, at power - down, possibly damaging the module. operating precautions: 1. do not plug or unplug the module when the system is powered up. 2. minimize the cable length between the module and host mpu. 3. for models with el backlights, do not disable the backlight by interrupting the hv line. unload inverters produce voltage extremes that may arc within a cable or at t he display. 4. operate the module within the limits of the modules temperature specifications. mechanical/environmental precautions: 1. improper soldering is the major cause of module difficulty. use of flux cleaner is not recommended as they may seep under the elastomeric connection and cause display failure. 2. mount the module so that it is free from torque and mechanical stress. 3. surface of the lcd panel should not be touched or scratched. the display front surface is an easily scratched, plastic polarizer. avoid contact and clean only when necessary with soft, absorbent cotton dampened with petroleum benzene. 4. always employ anti - static procedure while handling the module. 5. prevent moisture build - up upon the module and observe the environmental constraints for storage temperature and humidity.
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 16 of 18 6. do not store in direct sunlight 7. if leakage of the liquid crystal material should occur, avoid contact with this material, particularly ingestion. if the body or clothing becomes contaminated by the liquid crystal materi al, wash thoroughly with water and soap storage precautions when storing the lcd modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. keep the modules in bags (avoid high temperature / high humidity and low temperatures belo w 0 c). whenever possible, the lcd modules should be stored in the same conditions in which they were shipped from our company. others liquid crystals solidify under low temperature (below the storage temperature range) leading to defective orientation or the generation of air bubbles (black or white). air bubbles may also be generated if the module is subject to a low temperature. if the lcd modules have been operating for a long time showing the same display patterns, the display patterns may remain on the screen as ghost images and a slight contrast irregularity may also appear. a normal operating status can be regained by suspending use for some time. it should be noted that this phenomenon does not adversely affect performance reliability. to mini mize the performance degradation of the lcd modules resulting from destruction caused by static electricity etc., exercise care to avoid holding the following sections when handling the modules. exposed area of the printed circuit board. terminal electrode sections. n using lcd modules liquid crystal display modules lcd is composed of glass and polarizer. pay attention to the following items when handling. 1. please keep the temperature within specified range for use and storage. polarization degradation , bubble generation or polarizer peel - off may occur with high temperature and high humidity. 2. do not touch, push or rub the exposed polarizers with anything harder than an hb pencil lead (glass, tweezers, etc.). 3. n - hexane is recommended for cleaning the adhe sives used to attach front/rear polarizers and reflectors made of organic substances which will be damaged by chemicals such as acetone, toluene, ethanol and isopropylalcohol. 4. when the display surface becomes dusty, wipe gently with absorbent cotton or oth er soft material like chamois soaked in petroleum benzin. do not scrub hard to avoid damaging the display surface. 5. wipe off saliva or water drops immediately, contact with water over a long period of time may cause deformation or color fading. 6. avoid contac ting oil and fats. 7. condensation on the surface and contact with terminals due to cold will damage, stain or dirty the polarizers. after products are tested at low temperature they must be warmed up in a container before coming is contacting with room tempe rature air. 8. do not put or attach anything on the display area to avoid leaving marks on. 9. do not touch the display with bare hands. this will stain the display area and degradate insulation between terminals (some cosmetics are determinated to the polarizer s). 10. as glass is fragile. it tends to become or chipped during handling especially on the edges. please avoid dropping or jarring. installing lcd modules the hole in the printed circuit board is used to fix lcm as shown in the picture below. attend to t he following items when installing the lcm. 1. cover the surface with a transparent protective plate to protect the polarizer and lc cell. 2. when assembling the lcm into other equipment, the spacer to the bit between the lcm and the fitting plate should have enough height to avoid causing stress to the module surface, refer to the individual specifications for measurements. the
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 17 of 18 measurement tolerance should be 0.1mm. precaution for handing lcd modules since lcm has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the module or making any alterations or modifications to it. 1. do not alter, modify or change the the shape of the tab on the metal frame. 2. do not make extra holes on the printed circuit board, modify its shape or change the positions of components to be attached. 3. do not damage or modify the pattern writing on the printed circuit board. 4. absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector. 5. exc ept for soldering the interface, do not make any alterations or modifications with a soldering iron. 6. do not drop, bend or twist lcm. electro - static discharge control since this module uses a cmos lsi, the same careful attention should be paid to electr ostatic discharge as for an ordinary cmos ic. 1. make certain that you are grounded when handing lcm. 2. before remove lcm from its packing case or incorporating it into a set, be sure the module and your body have the same electric potential. 3. when soldering the terminal of lcm, make certain the ac power source for the soldering iron does not leak. 4. when using an electric screwdriver to attach lcm, the screwdriver should be of ground potentiality to minimize as much as possible any transmission of electromagnetic waves produced sparks coming from the commutator of the motor. 5. as far as possible make the electric potential of your work clothes and that of the work bench the ground potential. 6. to reduce the generation of static electricity be careful that the air in th e work is not too dried. a relative humidity of 50% - 60% is recommended. precaution for soldering to the lcm 1. observe the following when soldering lead wire, connector cable and etc. to the lcm. soldering iron temperature : 280 c 10 c. soldering time : 3 - 4 sec. solder : eutectic solder. if soldering flux is used, be sure to remove any remaining flux after finishing to soldering operation. (this does not apply in the case of a non - halogen type of flux.) it is recommended that you protect the lcd surface with a cover during soldering to prevent any damage dur to flux spatters. 2. when soldering the electroluminescent panel and pc board, the panel and board should not be detached more than three times. this maximum number is determined by the temperature and t ime conditions mentioned above, though there may be some variance depending on the temperature of the soldering iron. 3. when remove the electoluminescent panel from the pc board, be sure the solder has completely melted, the soldered pad on the pc board coul d be damaged. precautions for operation 1. viewing angle varies with the change of liquid crystal driving voltage (vo). adjust vo to show the best contrast. 2. driving the lcd in the voltage above the limit shortens its life. 3. response time is greatly delayed at temperature below the operating temperature range. however, this does not mean the lcd will be out of the order. it will recover when it returns to the specified temperature range. 4. if the display area is pushed hard during operation, the display will be come abnormal. however, it will return to normal if it is turned off and then back on. 5. condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit. therefore, it must be used under the relative condition of 40 c , 50% rh . 6. when turning the power on, input each signal after the positive/negative voltage becomes stable.
displayte ch ltd lcd module 32128a - rgb series version : 1. 1 p 18 of 18 storage when storing lcds as spares for some years, the following precaution are necessary. 1. store them in a sealed polyethyle ne bag. if properly sealed, there is no need for dessicant. 2. store them in a dark place. do not expose to sunlight or fluorescent light, keep the temperature between 0 c and 35 c. 3. the polarizer surface should not come in contact with any other objects. (we advise you to store them in the container in which they were shipped.) 4. environmental conditions : do not leave them for more than 168hrs. at 60 c. should not be left for more than 48hrs. at - 20 c. safety 1. it is recommended to crush damaged or unnecessary lcds into pieces and wash them off with solvents such as acetone and ethanol, which should later be burned. 2. if any liquid leakes out of a damaged glass cell and comes in contact with the hands, wash off thoroughly with soap and water. limited warranty unless agreed between displaytech and customer, displaytech will replace or repair any of its lcd modules which are found to be functionally defective when inspected in accordance with displaytech lcd acceptance standards (copies available upon request) f or a period of one year from date of shipments. cosmetic/visual defects must be returned to displaytech within 90 days of shipment. confirmation of such date shall be based on freight documents. the warranty liability of displaytech limited to repair and/o r replacement on the terms set forth above. displaytech will not be responsible for any subsequent or consequential events. return lcm under warranty no warranty can be granted if the precautions stated above have been disregarded. the typical examples of violations are : broken lcd glass. pcb eyelet s damaged or modified. pcb conductors damaged. circuit modified in any way, including addition of components. pcb tampered with by grinding, engraving or painting varnish. soldering to or modifying the beze l in any manner. module repairs will be invoiced to the customer upon mutual agreement. modules must be returned with sufficient description of the failures or defects. any connectors or cable installed by the customer must be removed completely without d amaging the pcb eyelet s, conductors and terminals. n revision record version changes date 1.0 initial revision 27 mar. 2006 1.1 maximum p ower s upply for l ogic at absolute maximu m ratings in page 2 15 apr. 2008
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: displaytech: ? 32128a fc bw-rgb
|
