321 dimensions are shown for reference purposes only. dimensions are in inches over (millimeters) unless otherwise specified. specifications and availability subject to change. www.tycoelectronics.com technical support: refer to inside back cover. axicom catalog 1308242 issued 3-03 (pdf rev. 4-04) file e111441 file 169679-1079886 16501-003 features through hole or surface mount terminals. meets bellcore gr 1089, fcc part 68 and itu-t k20. for applications in telecommunications, office automation, consumer electronics, medical equipment, measurement and control equipment. immersion cleanable, plastic sealed case. ?100mw coil for latching models, 140mw coil for non-latching. ultrasonic cleaning not recommended. coil data @ 23 c operate data @ 23 c operate and release voltage: see values in chart above. operate time (at nominal voltage): 1 ms, typ.; 3 ms, max. reset time [latching](at nominal voltage): 1 ms, typ.; 3 ms, max. release time [non-latching](without diode in parallel): 1 ms, typ.; 3 ms, max. release time [non-latching](with diode in parallel): 3 ms, typ.; 5 ms, max. bounce time (at contact close): 1 ms, typ.; 5 ms, max. maximum switching rate (no load): 50 operations/s. environmental data temperature range: -55 c to +85 c. maximum allowable coil temperature: 125 c. thermal resistance: < 150k/w. shock, half sinus, 11 ms: functional: 50g. shock, half sinus, 0.5 ms: destructive: 500g. vibration, 10-1000 hz.: functional: 20g. needle flame test: application time 20s. resistance to soldering: 260 c for 10s. initial insulation resistance between contact and coil: 10 9 ohms or more @ 500vdc. contact data @ 23 c (except as noted) arrangement: 2 form c (dpdt) bifurcated contacts. material: stationary: palladium-ruthenium, gold covered. ratings: max. switched current: 2a. max. carry current: 2a (at max ambient temperature. max. switched voltage: 220vdc, 250vac. max. switched power: 60w dc or 62.5va ac. ul/csa ratings: 250ma @ 250vac; 2a @ 30vdc; 500ma @ 120vdc; 270ma @ 220vdc. initial contact resistance: <70 milliohms @ 10ma / 20mv. expected mechanical life: 100 million operations. expected electrical life: 2.5 million operations @ 10ma / 30mvdc. 2 million operations @ cable load open end. 500,000 operations @ 240ma / 125vdc, res. 500,000 operations @ 1a / 30vdc, res. 100,000 operations @ 270ma / 220vdc, res. 100,000 operations @ 2a / 30vdc, res. 100,000 operations @ 250ma / 250vdc, res. thermoelectric potential: <10 v. initial dielectric strength between open contacts: 1,000vrms for 1 minute. between coil and contacts: 1,800vrms for 1 minute. between poles: 1,000vrms for 1 minute. surge voltage resistance per bellcore 1089 (2 / 10 s), fcc 68 (10 / 160 s) and iec (10 / 700 s): between open contacts: 1,500v. between coil and contacts: 2,500v. between poles: 1,500v. nominal operate/set range minimum resistance part voltage minimum maximum release/reset 10% number (vdc) voltage voltage voltage (ohms) (vdc) (vdc) (vdc) non-latching 1 coil versions 1.5 1.13 3.4 0.15 16 im00 3 2.1 6.8 0.3 64 im01 4.5 3.15 10.3 0.45 145 im02 5 3.5 11.4 0.5 178 im03 6 4.2 13.7 0.6 257 im04 9 6.3 20.4 0.9 574 im05 12 8.4 27.3 1.2 1,028 im06 24 16.8 45.6 2.4 2,880 im07 latching 1 coil versions 1.5 1.13 4.1 -1.13 23 im40 3 2.25 8.1 -2.25 90 im41 4.5 3.38 12.1 -3.38 203 im42 5 3.75 13.5 -3.75 250 im43 6 4.5 16.2 -4.5 360 im44 9 6.75 24.2 -6.75 810 im45 12 9.0 32.3 -9.0 1,440 im46 24 18.0 41.9 -18.0 2,880 im47 mechanical data termination: through-hole printed circuit terminals or gull-wing or j-leg surface mount printed circuit terminals. mounting position: any. enclosure type: immersion cleanable (ip67) plastic case. weight: 0.03 oz. (.75g) approximately. high frequency data capacitance: between open contacts: 1pf, max. between coil and contacts: 2pf, max. between poles: 2pf, max. rf characteristics: isolation at 100 / 900 mhz: -37.0 db / -18.8 db. insertion loss at 100 / 900 mhz: -0.03 db / -0.33 db. v. s. w. r. at 100 / 900 mhz: 1.06 / 1.49 . users should thoroughly review the technical data before selecting a product part number. it is recommended that users also seek out the pertinent approvals files of the agencies/laboratories and review them to ensure the product meets the requirements for a given application. coil data @ 23 c voltage: 1.5 to 24vdc. nominal power: 100mw for 1.5 - 12vdc latching models; 140mw for 1.5 - 12vdc non-latching models; 200mw for all 24vdc models. duty cycle: continuous. im series dpdt slimline and low profile telecom/signal pc board relays
322 dimensions are shown for reference purposes only. dimensions are in inches over (millimeters) unless otherwise specified. specifications and availability subject to change. axicom catalog 1308242 issued 3-03 www.tycoelectronics.com technical support: refer to inside back cover. .393 .003 (10 .08 ) .236 .003 (6 .08 ) .222 C .008 (5.65 C .2 ) .125 (3.2) .015 (.4) .2 .004 (5.08 .1 ) .126 .006 (3.2 .15 ) .087 .006 (2.2 .15 ) d2= d1= d1 d2 d2 our authorized distributors are more likely to stock the following items for immediate delivery. outline dimensions wiring diagram (bottom view) pc board layout (bottom view) none at present. ordering information see "part number" column in coil data chart on previous page for available base part numbers in the im series. for tht versions, add the suffix "ts" to the base part number. for gull-wing smt versions, add the suffix "gr" to the base part number. for j-leg smt versions, add the suffix "jr" to the base part number. packaging information tht im series relays are shipped in tubes of 50. there are 1,000 relays in a full carton. smt im series relays are shipped in reels of 1,000. there are 1,000 or 5,000 relays in a full carton. u i = minimum voltage at 23 c after pre-energizing with nominal voltage without contact current u ii = maximum continous voltage at 23 the operating voltage limits u i and u ii depend on the temperature according to the formula: u i tamb =k i ?u i 23 c and u ii tamb =k il ?u il 23 c t amb = ambient temperature u i tamb = minimum voltage at ambient temperature, t amb u ii tamb = maximum voltage at ambient temperature, t amb k i , k ii = factors (dependent on temperature), see diagram ambient temperature t amb [ c] .126 (3.2) .087 (2.2) .087 (2.2) .047 .006 (1.2 .15 ) .030 (.75) dia. min. .2 .006 (5.08 .15 ) .018 .006 (.46 .15 ) .393 .003 (10 .08 ) .236 .003 (6 .08 ) .222 C .008 (5.65 C .2 ) .015 (.4) .126 .006 (3.2 .15 ) .087 .006 (2.2 .15 ) d2= d1= d1 d2 d2 .2 .004 (5.08 .1 ) .295 .011 (7.5 .3 ) .393 .003 (10 .08 ) .236 .003 (6 .08 ) .222 C .008 (5.65 C .2 ) .015 (.4) .126 .006 (3.2 .15 ) .087 .006 (2.2 .15 ) d2= d1= d1 d2 d2 t1 t2 .110 .007 (2.8 .2 ) .2 .004 (5.08 .1 ) t2= t1= solder pad layout (bottom views) .126 (3.2) .087 (2.2) .087 (2.2) .236 (6) .157 (4) .315 (8) .047 .006 (1.2 .15 ) .028 .004 (.7 .1 ) .126 (3.2) .087 (2.2) .087 (2.2) .173 (4.4) .094 (2.4) .252 (6.4) .047 .006 (1.2 .15 ) .028 .004 (.7 .1 ) tht version smt version w/ gull wings smt version w/ j legs tht version smt version w/ gull wings smt version w/ j legs recommended soldering conditions (according to cecc 00802) 10 sec ca. 40 sec max. 245 c 215 c 180 c 130 c solid line: typical dotted line: process limits time (s) temperature c infrared soldering: temperature/time profile (lead temperature) vapor phase soldering: temperature/time profile (lead temperature) 20-40 sec forced cooling external preheating 215 c 180 c 130 c solid line: typical dotted line: process limits time (s) temperature c 100 c
|
