caution : observe precautions when handling because these devices are sensitive to electrostatic discharge d pdt switch for 2.4 ghz and 6 ghz dual - band wireless lan gaas integrated circuit ? pg2 16 4 t 5 n d ocument no. p g 106 3 6 ej0 2 v0ds ( 2nd edition) date published february 200 8 ns the mark shows major revised points. the revised points can be easily searched by copying an "" in the pdf file and specifying it in the "find what:" field. description the ? pg 2164 t 5 n is a gaas mmic d pdt ( d ouble p ole d ouble t hrow) switch w hi ch was developed for 2.4 ghz and 6 ghz dual - band wireless lan. this device can operate frequency from 2.4 ghz band and 6 ghz band, having the low insertion loss and high isolation . this device is housed in a 6 - pin plastic ts o n ( t hin s mall o ut - line n on - l eaded) package. and this package is able to high - density surface mounting. features ? operating frequency : f = 2.4 to 2.5 ghz and 4.9 to 6.0 ghz ? switch c ontrol v oltage : v cont (h) = 2.8 to 5.0 v ( 3.0 v typ.) : v cont (l) = ? 0 .3 to 0.3 v ( 0 v typ.) ? low i nsertion l oss : l ins 1 = 0. 5 0 db typ. @ f = 2.4 to 2.5 ghz , v cont (h) = 3. 0 v, v cont (l) = 0 v : l ins 2 = 0. 7 0 db typ. @ f = 4.9 to 6.0 ghz, v cont (h) = 3. 0 v, v cont (l) = 0 v ? high isolation : isl 1 = 25 db typ. @ f = 2.4 to 2.5 ghz, v cont (h) = 3. 0 v, v cont (l) = 0 v : isl 2 = 17 db typ. @ f = 4.9 to 6.0 ghz, v cont (h) = 3. 0 v, v cont (l) = 0 v ? handling power : p in (1 db) = +31.0 db m typ. @ f = 2.5 ghz, v cont (h) = 3. 0 v, v cont (l) = 0 v : p in (1 db) = +29.0 db m typ. @ f = 6.0 ghz, v cont (h) = 3. 0 v, v cont (l) = 0 v ? high - density surface mounting : 6 - pin plastic ts o n package ( 1.5 ? 1.5 ? 0. 37 mm) application ? d ual - band wireless lan (ieee802.11a + b/g) ordering i nformation part number order number package marking supplying form ? pg 2164 t 5 n - e 2 ? pg 2164 t5 n - e2 - a 6 - pin plastic ts o n (pb - free) g 5b ? embossed tape 8 mm wide ? pin 1 , 6 face the perforation side of the tape ? qty 3 kpcs/reel remark to order evaluation sa mples, contact your nearby sales office. part number for sample order: ? pg 2164 t 5 n - a
data sheet pg10 6 3 6 ej 0 2 v0ds 2 ? pg2 16 4 t 5 n pin connections and internal block diagram pin no. pin name 1 ant2 2 v cont 2 3 out2 (rx) 4 out1 (tx) 5 v cont 1 6 ant 1 remark exposed pad : gnd truth ta ble v cont 1 v cont 2 ant 1 ? out1 (tx) ant1 ? out2 (rx) ant2 ? out1 (tx) ant 2 ? out2 (rx) high low off on on off low high on off off on absolute maximum ratings (t a = +25 ? parameter symbol ratings unit switch control voltage v c ont ? 6.0 to + 6.0 v input power p in + 32 dbm operating ambient temperature t a ? 4 5 to +85 ? c storage temperature t stg ? 55 to +1 35 ? c recommended operating r a nge (t a = +25 ? parameter symbol min. typ. max. unit switch con trol voltage (h) v cont (h) 2.8 3.0 5.0 v switch control voltage (l) v cont (l) ? 0.3 0 0.3 v operating frequency 1 f 1 2 . 4 ? 2 . 5 g hz operating frequency 2 f2 4.9 ? 6.0 ghz
data sheet pg10 6 3 6 ej 0 2 v0ds 3 ? pg2 16 4 t 5 n electrical characteristics (t a = +25 ? cont (h) = 3.0 v, v cont (l) = 0 v, z 0 = 50 ? parameter symbol test conditions min. typ. max. unit insertion loss 1 l ins 1 f = 2.4 to 2.5 ghz ? 0. 5 0 0. 75 db insertion loss 2 l ins 2 f = 4.9 to 6.0 ghz ? 0. 7 0 1 . 0 0 db isolation 1 (ant to out) isl1 f = 2.4 to 2.5 ghz 22 25 ? db isolation 2 (ant to out) isl2 f = 4.9 to 6.0 ghz 14 17 ? db isolation 3 (ant1 to ant2, tx to rx) isl3 f = 2.4 to 2.5 ghz 22 25 ? db isolation 4 (ant1 to ant2, tx to rx) isl4 f = 4.9 to 6.0 ghz 15 17 ? db input r eturn loss 1 rl in 1 f = 2.4 to 2.5 ghz ? 15 ? db input return loss 2 rl in 2 f = 4.9 to 6.0 ghz ? 15 ? db output return loss 1 rl out 1 f = 2.4 to 2.5 ghz ? 15 ? db output return loss 2 rl out 2 f = 4.9 to 6.0 ghz ? 15 ? db 1 db loss compression input power 1 note p in (1 db) 1 f = 2.4 to 2.5 ghz ? +31.0 ? dbm 1 db loss compression input power 2 note p in (1 db) 2 f = 4.9 to 6.0 ghz ? +29.0 ? dbm input 3rd order intercept point iip 3 f1 = 2 500 mhz, f2 = 2 501 mhz, p in (1 tone ) = +20 dbm ? +5 0 ? dbm switch c ontrol current i cont ? 0.1 1.0 ? a switch control speed t sw 50% ctl to 90/10% ? 50 ? ns note p in (1 db) is measured the input power level when the insertion loss increases more 1 db than that of linear range. caution this device is used it is necessary to use dc blocking capacitors.
data sheet pg10 6 3 6 ej 0 2 v0ds 4 ? pg2 16 4 t 5 n evaluation circuit the application circuits and their parameters are for reference only and are not intended for use in actual design - ins.
data sheet pg10 6 3 6 ej 0 2 v0ds 5 ? pg2 16 4 t 5 n mounting pad and solder mask layout dimensions 6 - pin plastic tson (unit: mm) remark the mounting pad and solder mask layouts in this document are for reference only.
data sheet pg10 6 3 6 ej 0 2 v0ds 6 ? pg2 16 4 t 5 n package dimensions 6 - pin plastic ts o n (un it: mm) < r >
data sheet pg10 6 3 6 ej 0 2 v0ds 7 ? pg2 16 4 t 5 n recommended soldering conditions this product should be soldered and mounted under the following recommended conditions. for soldering methods and conditions other than those recommended below, contact your nearby sales office. soldering m ethod soldering conditions condition symbol infrared reflow peak temperature (package surface temperature) : 260 ? c or below time at peak temperature : 10 seconds or less time at temperature of 220 ? c or higher : 60 seconds or less preheating time at 120 to 180 ? c : 120 ? 30 seconds maximum number of reflow processes : 3 times maximum chlorine content of rosin flux (% mass) : 0.2%(wt.) or below ir260 wave soldering peak temperature (molten solder temperature) : 260 ? c or below time at peak temperature : 10 seco nds or less preheating temperature (package surface temperature) : 120 ? c or below maximum number of flow processes : 1 time maximum chlorine content of rosin flux (% mass) : 0.2%(wt.) or below ws260 partial heating peak temperature ( terminal temperature) : 350 ? c or below soldering time (per side of device) : 3 seconds or less maximum chlorine content of rosin flux (% mass) : 0.2%(wt.) or below hs350 caution do not use different soldering methods together (except for partial heating).
8 data sheet pg10 6 3 6 ej 0 2 v0ds ? pg2 16 4 t 5 n caut ion gaas products this product uses gallium arsenide (gaas). gaas vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. ? follow related laws and ordinances when disposing of the product. if there ar e no applicable laws and/or ordinances, dispose of the product as recommended below. 1. commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. ? do not burn, destroy, cut, crush, or chemically dissolve the pro duct. ? do not lick the product or in any way allow it to enter the mouth.
|
