1 / 3 www.asb.co.kr july 20 09 p lerow tm ALN2540M3 internally matched lna module parameter unit specifications min typ max frequency range mhz 2525 2555 gain db 34.5 35.5 gain flatness db ? 0.2 ? 0.3 noise figure (nf) db 0.65 0.70 output ip3 (1) dbm 33.5 34.5 s11 / s22 (2) db - 12 / - 12 output p1db dbm 17 18 switching time ? sec - supply current ma 200 240 supply voltage v 5 impedance ? 50 max. rf input power dbm c.w 29 ~ 31 (before fail) package type & size mm surface mount type, 25wx13lx3.0h operating temperature is - 40 ? c to +85 ? c. 1) oip3 is measured wi th two tones at an output power of +4 dbm / tone separated by 1 mhz. 2) s11/s22 (max) is the worst value within the frequency band. 3) switching time means the time that takes for output power to get stabilized to its final level after switching dc voltage from 0 v to vs . pin number function 3 rf in 8 rf out 10 v s other s ground s 21 = 35.6 db @ 2525 mhz = 35.4 db @ 2555 mhz nf of 0.65 db over fr e quency unconditionally stable single 5v supply high oip3 @ low current the plerow tm aln - series is the compactly designed surface - mount module for the use of the lna with or without the following gain blocks in the infrastructure equipment o f the mobile wireless (cdma, gsm, pcs, phs, wcdma, dmb, wlan, wibro, wimax), gps, satellite commun i- cation terminals , catv and so on. it has an exceptional performance of low noise figure, high gain, high oip3, and low bias current. the stability factor is always kept more than unity over the application band in order to ensure its unconditionally stable implementation to the application system environment. the surface - mount module package including the completed matching circuit and other components necessa ry just in case allows very simple and convenient implementation onto the system board in mass production level. ou t line drawing (unit: mm) feature s specifications (in pr o duction) note: 1. the number and size of ground via holes in a circuit board is critical for thermal rf grounding consider a tions. 2. we recommend that the ground via holes be placed on the bottom of all ground pins for better rf and thermal performance, as shown in the dra w ing at the left side. description typ. @ t = 25 ? c, v s = 5 v, freq. = 2540 mhz, z o.sys = 50 ohm c o u pl er website: www.asb.co.kr e - mail: s ales@asb.co.kr tel: (82) 42 - 528 - 722 3 f ax : (82) 42 - 528 - 7222 more inform a tion c o u pl er c o u pl er c o u pl er c o u pl er 3 - stage single type (top view) (bottom view) solder stencil area ? 0.4 plated thru holes to ground plane plerow ( side view) (recommended footprint) ALN2540M3
2 / 3 www.asb.co.kr july 20 09 p lerow tm ALN2540M3 internally matched lna module s - param e ters noise figure oip3 p1db 2525~2555 mhz +5 v stability fa c tor (k) typical performance (measured)
3 / 3 www.asb.co.kr july 20 09 p lerow tm ALN2540M3 internally matched lna module 1) the tantal or mlc (multi layer ceramic) capacitor is optional and for bypassin g the ac noise introduced from the dc supply. the capacitance value may be determined by customer s dc supply status . the c a- pacitor should be placed as close as possible to v s pin and be connected directly to the ground plane for the best electrical perfor mance . 2) dc blocking capacitors are always necessarily placed at the input and output port for allowing only the rf signal to pass and blocking the dc component in the signal. the dc blocking capacitors are inclu d- ed inside the aln module. therefore, c1 & c2 capacitors may not be necessary, but can be added just in case that the customer wants. the value of c1 & c2 is determined by considering the application fr e- quency. application circuit recommended soldering reflow process + - aln out in c1 c2 v s tantal or mlc (multi layer c e ramic) c a pacitor 20~40 sec 260 ? c 200 ? c 150 ? c 60~180 sec ramp - up (3 ? c/sec) ramp - down (6 ? c/sec) in out vs size 40 x 40 mm (for aln - m3 series C 25 x13mm) evaluation board layout
|
