filename: TFS150AR.doc version 2.2 08.10.2012 vectron international filter specification tfs 150a r 1/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. measurement condition ambient temperature: 23 c input power level: 0 dbm terminating impedance: * input: 73.43 || - 16.87 pf output: 111.51 || - 11.96 pf characteristics remark: the reference level for the relative attenuation a rel of the tfs 150ar is the minimum of the pass band a ttenuation a min . the minimum of the pass band attenuation a min is defined as the insertion loss a e . the centre frequency f c is the arithmetic mean value of the upper and lowe r frequencies at the 3 db filter attenuation level relative to the insertion loss a e . the temperature coefficient of frequency tc f is valid for both the reference frequency f c and the frequency response of the filter in the operating t emperature range. the frequency shift of the filter in the operating temperature range is not included in the production tolerance scheme. d a t a typ. value tolerance / limit insertion loss a e 21,6 db max. 24,0 db (reference level) nominal frequency f n - 150,0 mhz centre frequency at ambient temperature f c 150,0 mhz 0,1 mhz passband pb f c 12,06 mhz pass band ripple p-p 0,7 db max. 1,0 db bandwidth bw 3 db 24,96 mhz min. 24,9 mhz 17 db 25,73 mhz max. 26,0 mhz 30 db 26,25 mhz max. 27,2 mhz relative attenuation a rel f c ? f c 12,06 mhz 0,7 db max. 1 db f c 13,0 mhz ? f c 13,6 mhz 25 db min. 17 db f c 13,6 mhz ? f c 17,0 mhz 36 db min. 30 db f c 17,0 mhz ? f c 50,0 mhz 50 db min. 45 db group delay mean value in pb 1,62 s max. 1,7 s group delay ripple within pb 104 ns max. 125 ns return loss within pb 12,1 db min. 8 db operating temperature range otr - - 30 c ... + 85 c storage temperature range - - 40 c ... + 85 c temperature coefficient of frequency tc f ** -74 ppm/k - *) the terminating impedances depend on parasites a nd q-values of matching elements and the board used , and are to be understood as reference values only. should there be additional questions do not h esitate to ask for an application note or contact o ur design team. **) ? f(hz) = tc f (ppm/k) x (t-t 0 ) x f to (mhz) generated: checked / approved:
filename: TFS150AR.doc version 2.2 08.10.2012 vectron international filter specification tfs 150a r 2/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. c1 l1 saw l2 c2 10 5 1, 2, 3, 4, 6, 7, 8, 9 r1 r2 140 145 150 155 160 -5 -4.5 -4 -3.5 -3 -2.5 -2 -1.5 -1 -0.5 0 frequency in mhz magnitude in db 140 145 150 155 160 1.508 1.5392 1.5704 1.6016 1.6328 1.664 1.6952 1.7264 1.7576 1.7888 1.82 frequency in mhz delay in s 100 110 120 130 140 150 160 170 180 190 200 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 frequency in mhz magnitude in db filter characteristic construction and pin connection (all dimensions in mm) 1 1,60 0,20 9,80 0,20 20 0,20 1,91 7,62 1,02 2,31 1 5 6 10 date code 50 ohm test circuit tfs 150ar x49 1 ground 2 ground 3 ground 4 output rf return 5 output 6 ground 7 ground 8 ground 9 input rf return 10 input date code: year + week x 2009 a 2010 b 2011 ...
filename: TFS150AR.doc version 2.2 08.10.2012 vectron international filter specification tfs 150a r 3/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. stability characteristics, reliability after the following tests the filter shall meet the whole specification: 1. shock: 500g, 1 ms, half sine wave, 3 shocks each plane; din iec 68 t2 - 27 2. vibration: 10 hz to 500 hz, 0,35 mm or 5 g respe ctively, 1 octave per min, 10 cycles per plane, 3 p lanes; din iec 68 t2 - 6 3. change of temperature: -55 c to 125c / 30 min. each / 1 0 cycles din iec 68 part 2 ? 14 test n 4. resistance to solder heat (reflow): reflow possible: three ti mes max.; for temperature conditions refer to the attached " air reflow temperature conditions" on page 4; this filter is rohs compliant (2002/95/eg, 2005/618 /eg) packing tape & reel: iec 286 ? 3, with exception of value f or n and minimum bending radius; tape type ii, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: min. 300 mm reel of empty components at start including leader : min. 500 mm trailer: min. 300 mm so w do po e ct p2 p1 d1 bo ao pull off direc tion type pin marker date co de t ko n w 2 w 1 a c the minimum bending radius is 45 mm. tape (all dimensions in mm) w :32,00 po :4,00 0,1 do :1,50 +0,1/-0 e :1,75 0,1 f :14,20 0,1 g(min) : p2 :2,00 0,1 p1 :16,00 0,1 d1(min) :2,00 ao :10,25 0,1 bo :20,45 ct :25,5 reel (all dimensions in mm) a : 330 w1 :32,4 w2(max) :38,4 n(min) : 100 c :13,0
filename: TFS150AR.doc version 2.2 08.10.2012 vectron international filter specification tfs 150a r 4/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. air reflow temperature conditions conditions exposure average ramp-up rate (30c to 217c) less than 3c/ second > 100c between 300 and 600 seconds > 150c between 240 and 500 seconds > 217c between 30 and 150 seconds peak temperature max. 260c time within 5c of actual peak temperature between 10 and 30 seconds cool-down rate (peak to 50c) less than 6c/second time from 30c to peak temperature no greater than 300 seconds temperature / c time / s max. 260c 217c 10 ... 30 s 30 ... 150 s max. 300 s chip-mount air reflow profile
filename: TFS150AR.doc version 2.2 08.10.2012 vectron international filter specification tfs 150a r 5/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. history version reason of changes name date 1.0 - generation of development specification tcuk 15.12.2010 1.1 - update with customer agreed changes, use the same package schematic as the tfs150al jaffer 17.03 .2011 2.0 - change 3db bw to 24.9mhz min (was 25mhz min) & update (with n22) typical values jaffer 09.05.201 1 2.1 - update from development to filter specificati on tcuk 19.10.2011 2.2 - correct typo error on tape & reel information . tcuk 08.10.2012
|
