View PS9124-F3_8379910.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

r08ds0049ej0100 rev.1.00 page 1 of 15 aug 30, 2013 the mark shows major revised points. the revised points can be easily searched by copying an "" in the pdf file and specifying it in the "find what:" field. data sheet ps9124 high cmr, 10 mbps open collector output type, 5-pin sop (so-5) photocoupler description the ps9124 is an optically coupled high-speed, active low type isolator containing a gaalas led on the input side and a photodiode and a signal processing circuit on the output side on one chip. features ? low power consumption (v cc = 3.3/5 v) ? small package (so-5) ? high-speed response (t phl = 100 ns max., t plh = 100 ns max.) ? high-speed (10 mbps) ? high isolation voltage (bv = 3 750 vr.m.s.) ? open collector output ? embossed tape product : PS9124-F3 : 2 500 pcs/reel ? pb-free product ? safety standards ? ul approved: no. e72422 ? csa approved: no. ca 101391 (ca5a, can/csa-c22.2 60065, 60950) ? din en 60747-5-5 (vde 0884-5) approved (option) applications ? fa network r08ds0049ej0100 rev.1.00 aug 30, 2013 53 12 4 1. anode 2. cathode 3. gnd 4. v o 5. v cc pin connection (top view)
ps9124 chapter title r08ds0049ej0100 rev.1.00 page 2 of 15 aug 30, 2013 package dimensions (unit: mm) 1.27 0.4 +0.10 ?0.05 0.25 m 0.10.1 2.60.2 (4.4)* 1 7.00.3 0.50.3 0.15 +0.10 ?0.05 3.4 +0.3 ?0.1 53 12 4 *1 ( ) indicates reference dimension. photocoupler construction parameter min. air distance 4.2 mm outer creepage distance 4.2 mm isolation distance 0.2 mm block diagram (unit: mm) 5 4 3 led output on l off h shield 1 2
ps9124 chapter title r08ds0049ej0100 rev.1.00 page 3 of 15 aug 30, 2013 marking example no. 1 pin mark initial of renesas (engraved mark) rank code year assembled (last 1 digit) week assembled n 2 31 9124 n231 r *1 *1 bar : pb-free type number assembly lot ni/pd/au plating ordering information part number order number solder plating specification packing style safety standards approval application part number *1 ps9124 ps9124-ax pb-free 20 pcs (tape 20 pcs cut) standard products ps9124 PS9124-F3 PS9124-F3-ax (ni/pd/au) embossed tape 2 500 (ul, csa pcs/reel approved) ps9124-v ps9124-v-ax 20 pcs (tape 20 pcs cut) din en60747-5-5 ps9124-v-f3 ps9124-v-f3-ax em bossed tape 2 500 (vde0884-5) pcs/reel approved (option) note: *1. for the application of the safety standard, following part number should be used.
ps9124 chapter title r08ds0049ej0100 rev.1.00 page 4 of 15 aug 30, 2013 absolute maximum ratings (t a = 25 c, unless otherwise specified) parameter symbol ratings unit diode forward current *1 i f 25 ma reverse voltage v r 5 v detector supply voltage v cc 7 v output voltage v o 7 v output current i o 25 ma power dissipation *2 p c 200 mw isolation voltage *3 bv 3 750 vr.m.s. operating ambient temperature t a ? 40 to +110 c storage temperature t stg ? 55 to +125 c notes: *1. reduced to 0.2 ma/ c at t a = 25 c or more. *2. reduced to 4.0 mw/ c at t a = 75 c or more. *3 ac voltage for 1 minute at t a = 25 c, rh = 60% between input and output. pins 1-2 shorted together, 3-5 shorted together. recommended operating conditions parameter symbol min. typ. max. unit low level input voltage v fl ? 2 0.8 v high level input current i fh 3.8 6.0 7.5 ma supply voltage v cc 2.7 3.3 3.6 v 4.5 5.0 5.5 ttl (r l = 1 k , loads) n 5 pull-up resistor r l 330 4 k
ps9124 chapter title r08ds0049ej0100 rev.1.00 page 5 of 15 aug 30, 2013 electrical characteristics (t a = ? 40 to +110 c, unless otherwise specified) parameter symbol conditions min. typ. *1 max. unit diode forward voltage v f i f = 10 ma, t a = 25 c 1.3 1.55 1.8 v reverse current i r v r = 3 v, t a = 25 c 10 a terminal capacitance c t f = 1 mhz, v f = 0 v, t a = 25 c 30 pf detector high level output current i oh v cc = v o = 3.3 v, v f = 0.8 v 1 80 a v cc = v o = 5.5 v, v f = 0.8 v 1 100 low level output voltage v ol v cc = 3.3 v, i f = 4.5 ma, i ol = 13 ma 0.2 0.6 v v cc = 5.5 v, i f = 4.5 ma, i ol = 13 ma high level supply current i cch v cc = 3.3 v, i f = 0 ma, v o = open 4 7 ma v cc = 5.5 v, i f = 0 ma, v o = open low level supply current i ccl v cc = 3.3 v, i f = 4.5 ma, v o = open 6 10 ma v cc = 5.5 v, i f = 4.5 ma, v o = open 7 10 v cc = 3.3 v, r l = 350 , v o = 0.8 v 1.0 3.0 coupled threshold input voltage (h l) i fhl v cc = 5 v, r l = 350 , v o = 0.8 v ma isolation resistance r i-o v i-o = 1 kv dc , rh = 40 to 60%, t a = 25 c 10 11 isolation capacitance c i-o v = 0 v, f = 1 mhz, t a = 25 c 0.6 pf propagation delay time t a = 25 c 40 75 (h l) *2 t phl v cc = 3.3 v, i f = 4.5 ma, r l = 350 , c l = 15 pf 100 ns t a = 25 c 40 75 v cc = 5 v, i f = 4.5 ma, r l = 350 , c l = 15 pf 100 propagation delay time t a = 25 c 50 75 (l h) *2 t plh v cc = 3.3 v, i f = 4.5 ma, r l = 350 , c l = 15 pf 100 ns t a = 25 c 45 75 v cc = 5 v, i f = 4.5 ma, r l = 350 , c l = 15 pf 100 pulse width distortion (pwd) ? t phl- t plh ? v cc = 3.3/5 v, i f = 4.5 ma, r l = 350 , c l = 15 pf 5 35 ns propagation delay skew t psk v cc = 3.3/5 v, i f = 4.5 ma, r l = 350 , c l = 15 pf 40 ns rise time t r v cc = 3.3/5 v, i f = 4.5 ma, r l = 350 , c l = 15 pf 20 ns fall time t f v cc = 3.3/5 v, i f = 4.5 ma, r l = 350 , c l = 15 pf 5 ns common mode transient immunity at high level output *3 cm h v cc = 3.3/5 v, t a = 25 c, i f = 0 ma, v o > 2 v, r l = 350 , v cm = 1 kv 10 15 kv/ s common mode transient immunity at low level output *3 cm l v cc = 3.3/5 v, t a = 25 c, i f = 4.5 ma, v o < 0.8 v, r l = 350 , v cm = 1 kv 10 15 kv/ s
ps9124 chapter title r08ds0049ej0100 rev.1.00 page 6 of 15 aug 30, 2013 notes: *1. typical values at t a = 25 c *2. test circuit for propagation delay time remark c l includes probe and stray wiring capacitance. *3. test circuit for common mode transient immunity remark c l includes probe and stray wiring capacitance. 47 pulse input (i f ) v o (monitor) v cc = 3.3/5.0 v input (monitor) 0.1 f c l = 15 pf r l = 350 (pw = 1 s, duty cycle = 1/10) i f v out 90% 10% t f t r 90% 10% input output 1.5 v v ol t phl t plh (i f = 4.5 ma) 50% 90% 10% 1 kv 0 v v oh 2 v 0.8 v v ol v cm v o (i f = 0 ma) v o (i f = 4.5 ma) t r t f v o (monitor) v cc = 3.3/5.0 v 0.1 f c l = 15 pf sw i f r l = 350 v cm = 1 kv +
ps9124 chapter title r08ds0049ej0100 rev.1.00 page 7 of 15 aug 30, 2013 typical characteristics (t a = 25 c, unless otherwise specified) remark the graphs indicate nominal characteristics. ambient temperature t a ( c) maximum forward current i f (ma) maximum forward current vs. ambient temperature ambient temperature t a ( c) detector power dissipation p c (mw) detector power dissipation vs. ambient temperature ambient temperature t a ( c) high level supply current i cch (ma) low level supply current i ccl (ma) supply current vs. ambient temperature 25 50 75 125 100 110 110 25 50 75 125 100 0 30 25 20 15 10 5 0 300 250 200 150 100 50 10 8 6 4 2 0 - 50 - 25 0 25 50 75 100 125 forward current i f (ma) output voltage v o (v) output voltage vs. forward current 1 024 35 4 3.5 3 2.5 2 1.5 1 0.5 forward voltage v f (v) forward current i f (ma) forward current vs. forward voltage 1.0 0.01 0.1 1 10 100 1.2 1.4 1.6 1.8 2.0 forward current i f (ma) output voltage v o (v) output voltage vs. forward current 1 024 35 6 5 4 3 2 1 i ccl (i f = 4.5 ma) i cch (i f = 0 ma) t a = 110 c 85 c 50 c 25 c 0 c - 4 0 c v cc = 3.3 v v cc = 5.5 v v cc = 3.3 v r l = 350 r l = 4.0 k r l = 1.0 k v cc = 5.5 v r l = 350 r l = 4.0 k r l = 1.0 k
ps9124 chapter title r08ds0049ej0100 rev.1.00 page 8 of 15 aug 30, 2013 remark the graphs indicate nominal characteristics. ambient temperature t a ( c) threshold input current i fhl , i flh (ma) threshold input current vs. ambient temperature ambient temperature t a ( c) propagation delay time t phl , t plh (ns), pulse width distortion (pwd) t phl ? t plh (ns) propagation delay time, pulse width distortion vs. ambient temperature ambient temperature t a ( c) threshold input current i fhl , i flh (ma) threshold input current vs. ambient temperature ambient temperature t a ( c) propagation delay time t phl , t plh (ns), pulse width distortion (pwd) t phl ? t plh (ns) propagation delay time, pulse width distortion vs. ambient temperature - 25 0 25 50 100 75 - 50 125 120 0.0 20 40 60 80 100 - 25 0 25 50 100 75 - 50 125 120 0.0 20 40 60 80 100 - 25 0 25 50 100 75 - 50 125 - 25 0 25 50 100 75 - 50 125 - 25 0 25 50 100 75 - 50 125 - 25 0 25 50 100 75 - 50 125 ambient temperature t a ( c) low level output voltage v ol (v) low level output voltage vs. ambient temperature 0.5 0.0 0.1 0.2 0.3 0.4 5 0 1 2 3 4 5 0 1 2 3 4 0.5 0.0 0.1 0.2 0.3 0.4 v cc = 3.3 v, i f = 4.5 ma v cc = 3.3 v, v o = 0.8 v, r l = 350 v cc = 5 v, v o = 0.8 v, r l = 350 v cc = 5.5 v, i f = 4.5 ma ambient temperature t a ( c) low level output voltage v ol (v) low level output voltage vs. ambient temperature i ol = 16 ma 13 ma 10 ma 6 ma i ol = 16 ma 13 ma 10 ma 6 ma i fhl i flh i fhl i flh v cc = 3.3 v, i f = 4.5 ma, r l = 350 t phl t plh pwd v cc = 5 v, i f = 4.5 ma, r l = 350 t phl t plh pwd
ps9124 chapter title r08ds0049ej0100 rev.1.00 page 9 of 15 aug 30, 2013 remark the graphs indicate nominal characteristics. ambient temperature t a ( c) switching time vs. ambient temperature - 25 0 25 50 100 125 75 - 50 - 25 0 25 50 100 125 75 - 50 forward current i f (ma) forward current i f (ma) 5 10 20 15 25 5 10 20 15 25 100 0 40 30 20 10 50 60 70 80 90 100 0 40 30 20 10 50 60 70 80 90 50 0 20 15 10 5 25 30 35 40 45 50 0 20 15 10 5 25 30 35 40 45 ambient temperature t a ( c) switching time t r , t f (ns) switching time t r , t f (ns) switching time vs. ambient temperature v cc = 3.3 v, t a = 25 c, r l = 350 v cc = 3.3 v, i f = 4.5 ma, r l = 350 v cc = 5 v, i f = 4.5 ma, r l = 350 v cc = 5 v, t a = 25 c, r l = 350 t plh t plh t phl t r t f t r t f t phl pwd pwd propagation delay time t phl , t plh (ns), pulse width distortion (pwd) t phl ? t plh (ns) propagation delay time t phl , t plh (ns), pulse width distortion (pwd) t phl ? t plh (ns) propagation delay time, pulse width distortion vs. forward current propagation delay time, pulse width distortion vs. forward current
ps9124 chapter title r08ds0049ej0100 rev.1.00 page 10 of 15 aug 30, 2013 taping specifications (unit: mm) outline and dimensions (tape) tape direction outline and dimensions (reel) packing: 2 500 pcs/reel PS9124-F3 1001.0 13.00.2 3302.0 2.00.5 17.51.0 13.51.0 2.00.5 13.00.2 r 1.0 21.00.8 1.550.1 2.00.05 4.00.1 1.750.1 3.90.1 3.45 max. 7.40.1 0.30.05 8.00.1 1.5 +0.1 ?0 5.50.1 12.00.2 3.00.1
ps9124 chapter title r08ds0049ej0100 rev.1.00 page 11 of 15 aug 30, 2013 recommended mount pad dimensions (unit: mm) d b1 b2 a ps9124 part number ab1 c d b2 6.25 1.27 2.54 0.8 1.45 c
ps9124 chapter title r08ds0049ej0100 rev.1.00 page 12 of 15 aug 30, 2013 notes on handling 1. recommended soldering conditions (1) infrared reflow soldering ? peak reflow temperature 260 c or below (package surface temperature) ? time of peak reflow temp erature 10 seconds or less ? time of temperature higher than 220 c 60 seconds or less ? time to preheat temperature from 120 to 180 c 120 30 s ? number of reflows three ? flux rosin flux containing small amount of chlorine (the flux with a maximum chlorine content of 0.2 wt% is recommended.) 12030 s (preheating) 220 c 180 c package surface temperature t ( c) time (s) recommended temperature profile of infrared reflow (heating) to 10 s to 60 s 260 c max. 120 c (2) wave soldering ? temperature 260 c or below (molten solder temperature) ? time 10 seconds or less ? preheating conditions 120 c or below (package surface temperature) ? number of times one (allowed to be dipped in solder including plastic mold portion.) ? flux rosin flux containing small amount of chlorine (the flux with a maximum chlorine content of 0.2 wt% is recommended.) (3) soldering by soldering iron ? peak temperature (lead part temperature) 350 c or below ? time (each pins) 3 seconds or less ? flux rosin flux containing small amount of chlorine (the flux with a maximum chlorine content of 0.2 wt% is recommended.) (a) soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead (4) cautions ? fluxes avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. cautions regarding noise be aware that when voltage is applied suddenly between the photocoupler?s input and output at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings.
ps9124 chapter title r08ds0049ej0100 rev.1.00 page 13 of 15 aug 30, 2013 usage cautions 1. this product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. by-pass capacitor of more than 0.1 f is used between v cc and gnd near device. also , ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. 3. avoid storage at a high temperature and high humidity.
ps9124 chapter title r08ds0049ej0100 rev.1.00 page 14 of 15 aug 30, 2013 specification of vde marks license document parameter symbol spec. unit maximum repetitive peak operating isolation voltage u iorm 707 v peak partial discharge test voltage at 100% production test u pr = 1.875 u iorm , method b, t m =1sec, p d < 5 pc u pr 1 326 v peak partial discharge test voltage at type test and sample test u pr = 1.6 u iorm , method a, t m =10sec, p d < 5 pc u pr 1 131 v peak maximum transient isolation volt age (transient overvoltage t ini =60sec) u iotm 6 000 v peak installation classification (iec 60664/ din en 60664-1/ vde0110 part 1) for rated mains voltage < 300 vr.m.s. for rated mains voltage < 600 vr.m.s. i - iv i - iii comparative tracking index (iec 60112/ din en 60112/ vde 0303 part 11) cti 175 material group (din en 60664 -1/ vde0110 part 1) iii a pollution degree (din en 60664-1/ vde0110 part 1) 2 climatic category (iec 60068-1/ din en 60068-1) 40/110/21 operating temperature range t a ?40 to +110 c storage temperature range t stg ?55 to +125 c isolation resistance, minimum value v io = 500 vdc at t a =25 c v io = 500 vdc at t a max. at least 100c ris min. ris min. 10 12 10 11 safety limiting values ratings (maximum allowable in the event of a fault or a failure, see thermal derating curve) maximum ambient safety temperature maximum input current maximum output power isolation resistance at v io = 500 vdc, t a =ts ts isi pso ris min. 150 200 300 10 9 c ma mw
ps9124 chapter title r08ds0049ej0100 rev.1.00 page 15 of 15 aug 30, 2013 caution gaas products this product uses gallium arsenide (gaas). gaas vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. ? follow related laws and ordinances when disposi ng of the product. if there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. commission a disposal company able to (with a license to) collect, tran sport and dispose of materials that contain arsenic and ot her such industrial waste materials. 2. exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subjec t to special control) up until final disposal. ? do not burn, destroy, cut, crush, or chemically dissolve the product. ? do not lick the product or in any way allow it to enter the mouth.
all trademarks and registered trademarks are t he property of their respective owners. c - 1 revision history ps9124 data sheet description rev. date page summary 0.01 jul 03, 2012 ? first edition issued throughout ?preliminary data sheet? is changed to ?data sheet.? modification of features p.1 modification of applications p.6 modification of test circuit for propagation delay time p.7 to 9 addition of typical characteristics p.10 modification of ta ping specifications p.12 addition of notes on handling 1.00 aug 30, 2013 p.14 addition of specification of vde marks license document
notice 1. descriptions of circuits, software and other related information in this document are provided only to illustrate the operat ion of semiconductor products and application examples. you are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. renesas electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 2. renesas electronics has used reasonable care in preparing the information included in this document, but renesas electronics does not warrant that such information is error free. renesas electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. 3. renesas electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property ri ghts of third parties by or arising from the use of renesas electronics products or technical information described in this document. no license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of renesas electronics or others. 4. you should not alter, modify, copy, or otherwise misappropriate any renesas electronics product, whether in whole or in part . renesas electronics assumes no responsibility for any losses incurred by you or third parties arising from such alteration, modification, copy or otherwise misappropriation of renesas electronics product. 5. renesas electronics products are classified according to the following two quality grades: "standard" and "high quality". t he recommended applications for each renesas electronics product depends on the product's quality grade, as indicated below. "standard": computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots etc. "high quality": transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; and safety equipment etc. renesas electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear reactor control systems, military equipment etc.). you must check the quality grade of each renesas electronics product before using it in a particular application. you may not use any renesas electronics product for any application for which it is not intended. renesas electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any renesas electronics product for which the product is not intended by renesas electronics. 6. you should use the renesas electronics products described in this document within the range specified by renesas electronics , especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. renesas electronics shall have no liability for malfunctions or damages arising out of the use of renesas electronics products beyond such specified ranges. 7. although renesas electronics endeavors to improve the quality and reliability of its products, semiconductor products have s pecific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. further, renesas electronics products are not subject to radiation resistance design. please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a renesas electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or systems manufactured by you. 8. please contact a renesas electronics sales office for details as to environmental matters such as the environmental compatib ility of each renesas electronics product. please use renesas electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the eu rohs directive. renesas electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 9. renesas electronics products and technology may not be used for or incorporated into any products or systems whose manufactu re, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. you should not use renesas electronics products or technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. when exporting the renesas electronics products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. 10. it is the responsibility of the buyer or distributor of renesas electronics products, who distributes, disposes of, or othe rwise places the product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, renesas electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of renesas electronics products. 11. this document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of renesa s electronics. 12. please contact a renesas electronics sales office if you have any questions regarding the information contained in this doc ument or renesas electronics products, or if you have any other inquiries. (note 1) "renesas electronics" as used in this document means renesas electronics corporation and also includes its majority-o wned subsidiaries. (note 2) "renesas electronics product(s)" means any product developed or manufactured by or for renesas electronics. htt p ://www.renesas.co m refer to "htt p ://www.renesas.com/" for the latest and detailed information . california eastern laboratories , inc. 4590 patrick henr y drive, santa clara, california 95054, u.s.a . tel: +1-408-919-2500, fax: +1-408-988-0279 renesas electronics europe limited dukes meadow, millboard road, bourne end, buckinghamshire, sl8 5fh, u.k tel: +44-1628-651-700, fax: +44-1628-651-804 renesas electronics europe gmbh arcadiastrasse 10, 40472 dsseldorf, germany tel: +49-211-65030, fax: +49-211-6503-1327 renesas electronics (china) co., ltd. 7th floor, quantum plaza, no.27 zhichunlu haidian district, beijing 100083, p.r.china tel: +86-10-8235-1155, fax: +86-10-8235-7679 renesas electronics (shanghai) co., ltd. unit 204, 205, azia center, no.1233 lujiazui ring rd., pudong district, shanghai 200120, china tel: +86-21-5877-1818, fax: +86-21-6887-7858 / -7898 renesas electronics hong kong limited unit 1601-1613, 16/f., tower 2, grand century place, 193 prince edward road west, mongkok, kowloon, hong kong tel: +852-2886-9318, fax: +852 2886-9022/9044 renesas electronics taiwan co., ltd. 13f, no. 363, fu shing north road, taipei, taiwan tel: +886-2-8175-9600, fax: +886 2-8175-9670 renesas electronics singapore pte. ltd. 80 bendemeer road, unit #06-02 hyflux innovation centre singapore 339949 tel: +65-6213-0200, fax: +65-6213-0300 renesas electronics malaysia sdn.bhd. unit 906, block b, menara amcorp, amcorp trade centre, no. 18, jln persiaran barat, 46050 petaling jaya, selangor darul ehsan, malaysia tel: +60-3-7955-9390, fax: +60-3-7955-9510 renesas electronics korea co. , ltd . 11f., samik lavied' or bld g ., 720-2 yeoksam-don g , kan g nam-ku, seoul 135-080, korea tel: +82-2-558-3737 , fax: +82-2-558-514 1 s ale s o ffi c e s ? 2013 renesas electronics corporation. all rig hts reserved. [colophon 2.2 ]

▲Up To Search▲

Price & Availability of PS9124-F3

	To Download PS9124-F3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .