page 1 of 8 i spec 01 i rev.00 i november 2014 crystals ? oscillators ? ceramic resonators ? ceramic filters ? saw components petermann - technik gmbh lechwiesenstr. 13 ? d - 86899 ? landsberg am lech tel: +49/8191/305395 ? fax: +49/8191/305397 info@petermann - technik.com ? www.petermann - technik.com + 100% pin - to - pin drop - in replacement to quartz and mems based xo + differential oscillator for low cost + low power consumption + extremely low rms phase jitter + excellent long time reliability + very tight frequency stability as low as 10 ppm + lvpecl and lvds output signals + outstanding long term aging + standard housings: 3.2x2.5; 5.0x3.2; 7.0x5.0 mm + pb - free, rohs and reach compliant / msl1@260c applications general data features + 10gb ethernet, sonet, sata, sas, fibre channel, pci express, + telecom, networking, instrumentation, storage, servers, + etc. high performance dif ferential oscillator series ? dlpo - 4 220 625mhz parameter and condit ions symbol min . typ . max . unit condition lvpecl and lvds, com mon electrical characteristics supply voltage v dd 2.97 3.3 3.63 v 2.25 2.5 2.75 v 2.25 C 3.63 v termination schemes in figures 1 and 2 - xx ordering code output frequency range f 220 mhz C 625 frequency stability f_stab - 10 C +10 ppm inclusive of initial tolerance, operating temperature, - 20 C +20 ppm rated power supply voltage, and load variations - 25 C +25 ppm - 50 C +50 ppm first year aging f_aging1 - 2 C +2 ppm 25c 10 - year aging f_aging10 - 5 C +5 ppm 25c operating temperature range t_use - 40 C +85 c industrial - 20 C +70 c commercial input voltage high vih 70% C C v dd pin 1, oe or st input voltage low vil C C 30% v dd pin 1, oe or st input pull - up impedance z_in C 100 250 k pin 1, oe logic high or logic low, or st logic high 2 C C m pin 1, st logic low start - up time t_start C 6 10 ms measured from the time v dd reaches its rated minimum value. resume time t_resume C 6 10 ms in standby mode, measured from the time st pin crosses 50% threshold. duty cycle dc 45 C 55 % contact petermann - technik for tighter duty cycle
page 2 of 8 i spec 01 i rev.00 i november 2014 crystals ? oscillators ? ceramic resonators ? ceramic filters ? saw components petermann - technik gmbh lechwiesenstr. 13 ? d - 86899 ? landsberg am lech tel: +49/8191/305395 ? fax: +49/8191/305397 info@petermann - technik.com ? www.petermann - technik.com parameter and condit ions symbol min . typ . max . unit condition lvpecl, dc and ac ch aracteristics current consumption i dd C 61 69 ma excluding load termination current, v dd = 3.3v or 2.5v oe disable supply current i_oe C C 35 ma oe = low output disable leakage current i_leak C C 1 a oe = low standby current i_std C C 100 a st = low, for all v dd s maximum output current i_driver C C 30 ma maximum average current drawn from out+ or out - output high voltage voh v dd - 1.1 C v dd - 0.7 v see figure 1(a) output low voltage vol v dd - 1.9 C v dd - 1.5 v see figure 1(a) output differential voltage swing v_swing 1.2 1.6 2.0 v see figure 1(b) rise/fall time tr, tf C 300 500 ps 20% to 80%, see figure 1(a) oe enable/disable time t_oe C C 115 ns f = 220 mhz - for other frequencies, t_oe = 100ns + 3 period rms period jitter t_jitt C 1.2 1.7 ps f = 220 mhz, v dd = 3.3v or 2.5v C 1.2 1.7 ps f = 312.5 mhz, v dd = 3.3v or 2.5v C 1.2 1.7 ps f = 622.08 mhz, v dd = 3.3v or 2.5v rms phase jitter (random) t_phj C 0.6 0.85 ps f = 312.5 mhz, integration bandwidth = 12 khz to 20 mhz, all v dd s lvds, dc and ac char acteristics current consumption i dd C 47 55 ma excluding load termination current, v dd = 3.3v or 2.5v oe disable supply current i_oe C C 35 ma oe = low differential output voltage vod 250 350 450 mv see figure 2 output disable leakage current i_leak C C 1 a oe = low standby current i_std C C 100 a st = low, for all v dd s vod magnitude change ? vod C C 50 mv see figure 2 offset voltage vos 1.125 1.2 1.375 v see figure 2 vos magnitude change ? vos C C 50 mv see figure 2 rise/fall time tr, tf C 495 600 ps 20% to 80%, see figure 2 oe enable/disable time t_oe C C 115 ns f = 220 mhz - for other frequencies, t_oe = 100ns + 3 period rms period jitter t_jitt C 1.4 1.7 ps f = 266 mhz, v dd = 3.3v or 2.5v C 1.4 1.7 ps f = 312.5 mhz, v dd = 3.3v or 2.5v C 1.2 1.7 ps f = 622.08 mhz, v dd = 3.3v or 2.5v rms phase jitter (random) t_phj C 0.6 0.85 ps f = 312.5 mhz, integration bandwidth = 12 khz to 20 mhz, all v dd s excellent reliability data mtbf 500 million hours shock resistance: 10.000 g vibration resistance: 70 g general data (continued)
page 3 of 8 i spec 01 i rev.00 i november 2014 crystals ? oscillators ? ceramic resonators ? ceramic filters ? saw components petermann - technik gmbh lechwiesenstr. 13 ? d - 86899 ? landsberg am lech tel: +49/8191/305395 ? fax: +49/8191/305397 info@petermann - technik.com ? www.petermann - technik.com pin symbol functionality 1 oe input h or open : specified frequency output l: output is high impedance st input h or open: specified frequency output l: device goes to sleep mode. supply current reduces to i_std. 2 nc na no connect; leave it floating or connect to gnd for better heat dissipation 3 gnd power v dd power supply ground 4 out+ output oscillator output 5 out - output complementary oscillator output 6 v dd power power supply voltage p in description top view 1 oe/st v dd 6 gnd 3 out+ 4 nc 2 5 out - wave form diagrams out - out+ gnd 20% 20% 80% 80% vol voh tf tr figure 1(a). lvpecl voltage levels per d ifferential pin (out +/out - )
page 4 of 8 i spec 01 i rev.00 i november 2014 crystals ? oscillators ? ceramic resonators ? ceramic filters ? saw components petermann - technik gmbh lechwiesenstr. 13 ? d - 86899 ? landsberg am lech tel: +49/8191/305395 ? fax: +49/8191/305397 info@petermann - technik.com ? www.petermann - technik.com wave form diagrams (continued) out - out+ gnd 20% 20% 80% 80% vos vod tf tr 0 v v_ swing t figure 1(b). lvpecl voltage levels acros s differential pair figure 2. lvds volta ge levels per differential pin (out+/out - ) termination diagrams lvpecl: out - out+ d - z0 = 50 ? d+ z0 = 50 ? v dd 50 ? 50 ? v tt = v dd - 2.0 lvpecl driver receiver device figure 3. lvpecl typ ical termination
page 5 of 8 i spec 01 i rev.00 i november 2014 crystals ? oscillators ? ceramic resonators ? ceramic filters ? saw components petermann - technik gmbh lechwiesenstr. 13 ? d - 86899 ? landsberg am lech tel: +49/8191/305395 ? fax: +49/8191/305397 info@petermann - technik.com ? www.petermann - technik.com termination diagrams lvpecl: out - out+ d - z0 = 50 ? d+ z0 = 50 ? v dd v tt r1 v dd = 3.3v => r1 = 100 to 150 ? v dd = 2.5v => r1 = 75 ? lvpecl driver receiver device r1 50 ? 50 ? 100nf 100nf figure 5. lvpecl wit h thevenin typical termination figure 4. lvpecl ac coupled termination out - out+ lvpecl driver d - z0 = 50 ? d+ z0 = 50 ? v dd r4 receiver device r3 v dd r2 r1 v dd = 3.3v => r1 = r3 = 133 ? and r2 = r4 = 82 ? v dd = 2.5v => r1 = r3 = 250 ? and r2 = r4 = 62.5 ? termination diagrams lvds: out - out+ d - d+ v dd lvds driver receiver device z0 = 50 ? z0 = 50 ? 100 ? figure 6. lvds singl e termination (load terminated)
page 6 of 8 i spec 01 i rev.00 i november 2014 crystals ? oscillators ? ceramic resonators ? ceramic filters ? saw components petermann - technik gmbh lechwiesenstr. 13 ? d - 86899 ? landsberg am lech tel: +49/8191/305395 ? fax: +49/8191/305397 info@petermann - technik.com ? www.petermann - technik.com dimensions and patte rns note: 1. a capacitor value of 0.1 f between v dd and gnd is recommended. package size C dimen sions (unit:mm) 3.2x 2.5 x 0.75 mm recommended land pat tern (unit:mm) [1] package size C dimen sions (unit:mm) 7.0x 5.0 x 0.90 mm recommended land pat tern (unit:mm) [1] package size C dimen sions (unit:mm) 5.0x 3.2 x 0.75 mm recommended land pat tern (unit:mm) [1] #6 #5 #4 #1 #2 #3 #6 #5 #4 #1 #2 #3 0.750.05 2.50.05 3.20.05 #1 #3 #2 #6 #4 #5 0.6 0.7 0.9 2.20 #6 #5 #4 #1 #2 #3 0.65 1.00 1.6 2.25 1.05 0.750.05 3.20.10 5.00.10 #1 #3 #2 #6 #4 #5 0.64 0.9 1.2 2.54 1.20 2.20 2.54 0.90 0.900.10 5.00.10 7.00.10 #1 #3 #2 #6 #4 #5 1.40 1.10 2.6 5.08 1.60 3.80 5.08 1.60
page 7 of 8 i spec 01 i rev.00 i november 2014 crystals ? oscillators ? ceramic resonators ? ceramic filters ? saw components petermann - technik gmbh lechwiesenstr. 13 ? d - 86899 ? landsberg am lech tel: +49/8191/305395 ? fax: +49/8191/305397 info@petermann - technik.com ? www.petermann - technik.com ordering information e xample : dlpo433 - 3225 - e - 10 - m - 625.000mhz - t - 1 please indicate your required parameters oscillator family dlpo4 temperature range c for 0 +70c m for - 20 +70c w for - 40 +85c supply voltage 25 for 2.5v 33 for 3.3v feature pin 1 e for output enable s for standby package size 3225 for 3.2 x 2.5 mm 5032 for 5.0 x 3.2 mm 7050 for 7.0 x 5.0 mm frequency stability 10 for 10 ppm 20 for 20 ppm 25 for 25 ppm 50 for 50 ppm dlpo4 33 - 3225 - e - 10 - m - 625.000mhz - t - 1 packing method b for bulks or tubes t for tape & reel signaling type 1 = lvpecl 2 = lvds frequency 220.000000 mhz to 625.000000 mhz samples are available within a short delivery period!
page 8 of 8 i spec 01 i rev.00 i november 2014 crystals ? oscillators ? ceramic resonators ? ceramic filters ? saw components petermann - technik gmbh lechwiesenstr. 13 ? d - 86899 ? landsberg am lech tel: +49/8191/305395 ? fax: +49/8191/305397 info@petermann - technik.com ? www.petermann - technik.com premium quality by petermann - technik our company is certi fied according to is o 9001:2008 in o c- tober 2013 by the dm sz certifikation gmbh. this is for you to e nsure that the principles of quality management are fully implemented in our quality ma- nagement system and quality control meth ods also do- minate our quality standards. reflow solder profi le ? petermann - technik gmbh 2014. the information contained herein is subject to change at any time without notice. petermann - techn ik owns all rights, title and interest to the intellectual property related to petermann - technik's products, including any software, fir mware, copyright, pa- tent, or trademark. the sale of petermann - technik products does not convey or imply any license under patent or other rights. pe termann - technik retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or services by petermann - technik. unless otherwise agreed to in writing by petermann - technik, any reproduction, modification, trans lation, com- pilation, or representation of this material shall be strictly prohibited.
|
