page 1 of 6 notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com the big deal ? ultra high ip3 ? broadband high dynamic range without external matching components ? operates to 105c ? may be used as a replacement to wj ah1 a,b product overview PHA-1H+ (rohs compliant) is an advanced wideband amplifer fabricated using e-phemt technology and offers extremely high dynamic range over a broad frequency range and with low noise fgure. in addition, the PHA-1H+, unlike competitive models, has good input and output return loss over a broad frequency range without the need for external matching components and has demonstrated excellent reliability. lead fnish is snagni. it has repeatable performance from lot to lot and is enclosed in a sot-89 package for very good thermal performance. feature advantages broad band: 0.05 to 6.0 ghz broadband covering primary wireless communications bands: cellular, pcs, lte, wimax extremely high ip3 versus dc power consumption 40.4 dbm typical at 2.4 ghz the PHA-1H+ matches industry leading ip3 performance relative to device size and power consumption. the combination of the design and e-phemt structure provides enhanced linearity over a broad frequency range as evidence in the ip3 being typically 20 db above the p 1db point. this feature makes this amplifer ideal for use in: ? driver amplifers for complex waveform up converter paths ? drivers in linearized transmit systems ? secondary amplifers in ultra high dynamic range receivers no external matching components required unlike competing products, mini-circuits PHA-1H+ provides input and output return loss of 10-23 db up to 4 ghz without the need for any external matching components low noise figure: 2.6db typ. up to 4 ghz 3.4db typ. up to 6 ghz a unique feature of the PHA-1H+ which separates this design from all competitors is the low noise fgure performance in combination with the high dynamic range. low juction temperature tj=115c at 85c lead temperature and 135c at 105c lead temperature results in excellent reliability. PHA-1H+ key features notes: a. suitability for model replacement within a particular system must be determined by and is solely the responsibility of the customer based on, among other things, electrical performance criteria, stimulus conditions, application, compatibility with other components and environmental conditions and stresses. b. the wj ah1 part number is used for identifcation and comparison purposes only. 50 ? 0.05 to 6 ghz sot-89 package ultra high dynamic range monolithic amplifer
page 2 of 6 notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com simplifed schematic and pin description function pin number description rf in 1 rf input pin. this pin requires the use of an external dc blocking capacitor chosen for the frequency of operation. rf-out and dc-in 3 rf output and bias pin. dc voltage is present on this pin; therefore a dc blocking capacitor is necessary for proper operation. an rf choke is needed to feed dc bias without loss of rf signal due to the bias connection, as shown in recommended ap - plication circuit, fig. 2 gnd 2,4 connections to ground. use via holes as shown in suggested layout for pcb design to reduce ground path inductance for best performance. 0.05-6 ghz case style: df782 PHA-1H+ product features ? high ip3, 40.4 dbm typ. at 2.4 ghz ? gain, 13.8 db typ. at 2 ghz ? high pout, p1db 22 dbm typ. at 2 ghz ? low noise fgure, 2.2 db @2 ghz ? no external matching components required ? may be used as replacement for wj ah1 a,b rev. or m150809 PHA-1H+ th/rs/cp 160223 general description PHA-1H+ (rohs compliant) is an advanced wideband amplifer fabricated using e-phemt technology and offers extremely high dynamic range over a broad frequency range and with low noise fgure. in addition, the PHA-1H+ has good input and output return loss over a broad frequency range without the need for external matching components. lead fnish is snagni. it has repeatable performance from lot to lot and is enclosed in a sot-89 package for very good thermal performance. typical applications ? base station infrastructure ? portable wireless ? catv & dbs ? mmds & wireless lan ? lte rf-in rf-out and dc-in gnd notes: a. suitability for model replacement within a particular system must be determined by and is solely the responsibility of the customer based on, among other things, electrical performance criteria, stimulus conditions, application, compatibility with other components and environmental conditions and stresses. b. the wj ah1 part number is used for identifcation and comparison purposes only. 3 rf-out & dc-in 2 ground 1 rf-in 4 ultra high dynamic range monolithic amplifer +rohs compliant the +suffix identifies rohs compliance. see our web site for rohs compliance methodologies and qualifications
page 3 of 6 notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com parameter ratings operating temperature (ground lead) -40c to 105c storage temperature -65c to 150c operating current at 5v 210 ma power dissipation 1 w input power (cw) 24 dbm dc voltage on pin 3 6 v 3. permanent damage may occur if any of these limits are exceeded. electrical maximum ratings are not intended for continuous normal operation. absolute maximum ratings 3 PHA-1H+ 1. measured on mini-circuits characterization test board tb-313. see characterization test circuit (fig. 1) 2. (current at 85c current at -45c)/130 electrical specifcations at 25c, unless noted parameter condition (ghz) vd=5.0v 1 units min. typ. max. frequency range 0.05 6.0 ghz gain 0.05 15.9 17.7 19.5 db 0.8 14.3 15.9 17.5 2.0 13.8 3.0 12.1 4.0 9.8 10.9 12.0 6.0 9.6 input return loss 0.05 11.9 db 0.8 13.0 18.2 2.0 12.5 3.0 10.8 4.0 10.3 6.0 8.1 output return loss 0.05 14.2 db 0.8 13.0 22.9 2.0 19.7 3.0 17.1 4.0 15.5 6.0 13.7 reverse isolation 2.0 19.6 db output power @1 db compression 0.05 20.0 22.1 dbm 0.8 20.0 21.8 2.0 20.0 22.6 3.0 22.2 4.0 22.5 6.0 22.0 output ip3 0.05 39.6 dbm 0.8 38.0 40.6 2.0 40.4 3.0 40.8 4.0 41.4 6.0 41.0 noise fgure 0.5 1.7 db 1.0 1.8 2.0 2.2 3.0 2.4 4.0 2.6 6.0 3.4 device operating voltage 4.8 5.0 5.2 v device operating current 132 165 ma device current variation vs. temperature 2 101 a/c device current variation vs voltage 0.057 ma/mv thermal resistance, junction-to-ground lead at 88c 36.1 c/w monolithic e-phemt mmic amplifer
page 4 of 6 notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com PHA-1H+ 38.0 38.3 38.5 38.8 39.0 39.3 39.5 39.8 40.0 40.3 40.5 40.8 41.0 41.3 41.5 41.8 42.0 42.3 42.5 42.8 number of units output ip3 histogram of oip3 @ 900 mhz 38.0 38.3 38.5 38.8 39.0 39.3 39.5 39.8 40.0 40.3 40.5 40.8 41.0 41.3 41.5 41.8 42.0 42.3 42.5 42.8 number of units output ip3 histogram of oip3 @ 2400 mhz 38.0 38.3 38.5 38.8 39.0 39.3 39.5 39.8 40.0 40.3 40.5 40.8 41.0 41.3 41.5 41.8 42.0 42.3 42.5 42.8 number of units output ip3 histogram of oip3 @ 3500 mhz monolithic e-phemt mmic amplifer
page 5 of 6 notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com PHA-1H+ fig 1. block diagram of test circuit used for characterization. (dut soldered on mini-circuits characterization test board tb-313 gain, return loss, output power at 1db compression (p1 db) , output ip3 (oip3) and noise fgure measured using agilents n5242a pna-x microwave network analyzer. conditions: 1. gain and return loss: pin= -25dbm 2. output ip3 (oip3): two tones, spaced 1 mhz apart, 5 dbm/tone at output. characterization test circuit rf-in rf-out 3 vcc (supply v oltage) blk-18+ bias-t ee zx85-12g-s+ 1 dut tb-313 2,4 +5v ph1h recommended application circuit 4 2 3 1 cblock in cblock ibias out vd rfc cbypass vcc fig 2. test board includes case, connectors, and components soldered to pcb product marking monolithic e-phemt mmic amplifer
page 6 of 6 notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com PHA-1H+ msl test flow chart esd rating human body model (hbm): class 1b (500 to <1000v) in accordance with ansi/esd stm 5.1 - 2001 machine model (mm): class m1 (pass 25v) in accordance with ansi/esd stm5.2-1999 msl rating moisture sensitivity: msl1 in accordance with ipc/jedec j-std-020d performance data data table swept graphs s-parameter (s2p files) data set (.zip fle) case style df782 (sot 89) plastic package, exposed paddle lead fnish: tin/silver/nickel tape & reel f55 standard quantities available on reel 7 reels with 20, 50, 100, 200, 500 or 1k devices suggested layout for pcb design pl-313 evaluation board tb-545-1h+ environmental ratings env08t8 additional detailed technical information additional information is available on our dash board. to access this information click here visual inspection electrical test sam analysis refow 3 cycles, 260c soak 85c/85rh 168 hours bake at 125c, 24 hours visual inspection electrical test sam analysis start finish additional notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp monolithic e-phemt mmic amplifer
|
