phase control thyristors stud version 80ria series 80a bulletin i25201 i t(av) 80 a @ t c 85 c i t(rms) 125 a i tsm @ 50hz 1900 a @ 60hz 1990 a i 2 t @ 50hz 18 ka 2 s @ 60hz 16 ka 2 s v drm /v rrm 400 to 1200 v t q typical 110 s t j - 40 to 125 c parameters 80ria unit typical applications dc motor controls controlled dc power supplies ac controllers features all diffused design g lass-metal seal up to 1200v international standard case to-209ac (to-94) threaded studs unf 1/2 - 20unf2a or iso m12x1.75 major ratings and characteristics case style to-209ac (to-94)
80ria series 2222222222222 12 i t(av) max. average on-state current 80 a 180 conduction, half sine wave @ case temperature 85 c i t(rms) max. rms on-state current 125 a dc @ 75c case temperature i tsm max. peak, one-cycle 1900 t = 10ms no voltage non-repetitive surge current 1990 t = 8.3ms reapplied 1600 t = 10m s 100% v rrm 1675 t = 8.3ms reapplied sinusoidal half wave, i 2 t maximum i 2 t for fusing 18 t = 10ms no voltage initial t j = t j max. 16 t = 8.3 ms reapplied 12.7 t = 10ms 100% v rrm 11.7 t = 8.3ms rea pplied i 2 ? t maximum i 2 ? t for fusing 180.5 ka 2 ? s t = 0.1 to 10ms, no voltage reapplied v t(to)1 low level value of threshold voltage v t(t o) 2 high level value of threshold voltage r t1 low level value of on-state slope resistance r t2 high level value of on-state slope resistance v tm max. on-state voltage 1.60 v i pk = 250 a, t j = 25c t p = 10ms sine pulse i h maximum holding current 150 i l typical latching current 400 0.99 (16.7% x p x i t(av) < i < p x i t(av) ), t j = t j max. 2.29 (16.7% x p x i t(av) < i < p x i t(av) ), t j = t j max. 1.84 (i > p x i t(av) ), t j = t j max. parameter 80ria units conditions 1.13 (i > p x i t(av) ), t j = t j max. on-state conduction ka 2 s m w v a ma t j = 25c, anode supply 12v resistive load electrical specifications voltage ratings voltage v drm /v rrm , max. repetitive v rsm , maximum non- i drm /i rrm max. type number code peak and off-state voltage repetitive peak voltage @ t j = 125c v v ma 40 400 500 80ria 80 800 900 15 120 1200 1300
80ria series fig. 1 - current ratings characteristics fig. 2 - current ratings characteristics fig. 3 - on-state power loss characteristics fig. 4 - on-state power loss characteristics
80ria series fig. 5 - maximum non-repetitive surge current fig. 6 - maximum non-repetitive surge current fig. 7 - on-state voltage drop characteristics fig. 8 - thermal impedance z thjc characteristics
80ria series fig. 9 - gate characteristics
80ria series 23 di/dt max. non-repetitive rate of rise t j = 125c, v d = rated v drm , i tm = 2xdi/dt snubber of turned-on current 300 a/s 0.2f, 15 w , gate pulse: 20v, 65 w , t p = 6s, t r = 0.5s per jedec standard rs-397, 5.2.2.6. gate pulse: 10v, 15 w source, t p = 6s, t r = 0.1s, v d = rated v drm , i tm = 50adc, t j = 25c. i tm = 50a, t j = t j max , di/dt = -5a/s min., v r = 50v , dv/dt = 20v/s, gate bias: 0v 25 w , t p = 500s dv/dt maximum critical rate of rise of off-state voltage i rrm max. peak reverse and off-state i drm leakage current blocking parameter 80ria units conditions 15 ma t j = 125c rated v drm /v rrm applied p gm maximum peak gate power 12 t j = t j max , t p 5ms p g(av) maximum average gate power 3 t j = t j max , f = 50hz, d% = 50 i gm max. peak positive gate current 3 a t j = t j max , t p 5ms +v gm maximum peak positive gate voltage -v gm maximum peak negative gate voltage i gt max. dc gate current required 270 t j = - 40c to trigger 120 ma t j = 25c 60 t j = 125c v g t max. dc gate voltage required 3.5 t j = - 40c to trigger 2.5 v t j = 25c 1.5 t j = 125c i gd dc gate current not to trigger 6 ma parameter 80ria units conditions triggering w 20 10 v t j = t j max , t p 5ms v gd dc gate voltage not to trigger 0.25 v max. gate current/ voltage not to trigger is the max. value which will not trigger any unit with rated v drm anode-to-cathode applied t j = t j max max. required gate trigger/ cur- rent/ voltage are the lowest value which will trigger all units 6v an- ode-to-cathode applied parameter 80ria units conditions switching s 500 v/ s t j = 125c exponential to 67% rated v drm t d typical delay time 1 t q typical turn-off time 110
80ria series 2222222222222 12 180 0.042 0.030 t j = t j max. 120 0.050 0.052 90 0.064 0.070 k/w 60 0.095 0.100 30 0.164 0.165 ordering information table 1 - i tav x 10a 2 - 0 = eyelet terminals (gate and auxiliary cathode leads) 1 = fast - on terminals (gate and auxiliary cathode leads) 2 = flag terminals (for cathode and gate terminals) 3 - ria = e ssential part number 4 - voltage code: code x 10 = v rrm (see voltage rating table) 5 - none = stud base 1/2 "20unf - 2a threads m = stud base metric threads m12 x 1.75 e 6 4 8 0 ria 120 m device code 1 2 t j max. operating temperature range -40 to 125 t stg max. storage temperature range -40 to 150 r t hjc max. thermal resistance, junction to case r t hcs ma x. thermal resistance, case to heatsink t mounting torque, 10% 15.5 (137) non lubricated threads 14 (120) lubricated threads wt approximate weight 130 g parameter 80ria units conditions 0.30 dc operation 0.1 mounting surface, smooth, flat and greased thermal and mechanical specification c k/w nm (lbf-in) 3 5 case style to-209ac(to-94) see outline table conduction angle sinusoidal conduction rectangular conduction units conditions d r thj-c conduction (the following table shows the increment of thermal resistence r thj-c when devices operate at different conduction angles than dc)
80ria series 23 outline table fast-on terminals case style to-209ac (to-94) all dimensions in millimeters (inches) white shrink c.s. 0.4 mm 2 215 (8.46) 10 (0.39) white gate red shrink red cathode red silicon rubber 4.3 (0.17) dia. 2 1 ( 0 . 8 3 ) * for metric device : m12 x 1.75 e 6 1 0 ( 0 . 3 9 ) m a x . 1 5 7 ( 6 . 1 8 ) 1 7 0 ( 6 . 6 9 ) (.0006 s.i.) glass metal seal 8.5 (0.3) dia. 16.5 (0.65) max. 23.5 (0.92) max. dia. m a x . 2 4 ( 0 . 9 4 ) m a x . 5 5 ( 2 . 1 7 ) m i n . c.s. 16mm 2 flexible lead (.025 s.i.) 2.5 (0.10) max. 2 0 ( 0 . 7 9 ) m i n . 1/2"-20unf-2a * sw 27 29.5 (1.16) max. 9 . 5 ( 0 . 3 7 ) m i n . case style to-208ad (to-83) all dimensions in millimeters (inches) 1 2 1/2"-20unf-2a * 29.5 (1.16) * for metric device: m12 x 1.75 e 6 m a x . 4 4 ( 1 . 7 3 ) 1 0 23.5 dia. 1 6 . 5 ( 0 . 6 5 ) 1 0 ( 0 . 3 9 ) 2 4 ( 0 . 9 4 ) m a x . ( 0 3 9 ) (0.93) max. 2 1 ( 0 . 8 3 ) 1.5 (0.06) dia. ( 0 . 4 7 ) 4 7 ( 1 . 8 5 ) m a x . glass-metal seal flag terminals s w 2 7 2.4 (0.09) 5.6 (0.22) 5.5 (0.22) dia. amp. 280000-1 ref-250
|
