View YB215CWCKW01-6B-JB_8540730.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

series yb2 panel seal pushbuttons www.nkk.com d114 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles general specifcations electrical capacity (resistive load) power level (silver): 3a @ 125v ac or 3a @ 250v ac or 3a @ 30v dc logic level (gold): 0.4va maximum @ 28v ac/dc maximum (applicable range 0.1ma ~ 0.1a @ 20mv ~ 28v) other ratings contact resistance: 50 milliohms maximum for silver; 100 milliohms maximum for gold insulation resistance: 200 megohms minimum @ 500v dc dielectric strength: 1,000v ac minimum between contacts for 1 minute minimum; 1,500v ac minimum between contacts & case for 1 minute minimum mechanical life: 1,000,000 operations minimum for momentary circuit 200,000 operations minimum for maintained circuit electrical life: 100,000 operations minimum nominal operating force: single pole: 1.5n double pole: 3.0n contact timing: nonshorting (break-before-make) travel: pretravel .059 (1.5mm); overtravel .059 (1.5mm); total travel .118 (3.0mm) materials & finishes bezel: black: glass fber reinforced polyamide (ul94v-0); silver: polycarbonate housing: glass fber reinforced polyamide (ul94v-0) base: diallyl phthalate resin (ul94v-0) movable contactor: phosphor bronze with silver or gold plating movable contacts: phosphor bronze & silver alloy stationary contacts: silver alloy or copper with gold plating switch terminals: phosphor bronze with tin plating lamp terminals: phosphor bronze with tin plating environmental data operating temperature range: C25c through +50c (C13f through +122f) for illuminated C25c through +70c (C13f through +158f) for nonilluminated humidity: 90 ~ 95% humidity for 96 hours @ 40c (104f) vibration: 10 ~ 55hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours shock: 50g (490m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) sealing: ip65 of iec60529 standard installation mounting torque: 0.785nm (6.95 lb ? in) maximum soldering time & temperature: manual soldering: 390c maximum for 4 seconds maximum standards & certifications flammability standards: ul94v-0 housing, base & black or metallic silver bezel ul: file no. e44145 - recognized only when ordered with marking on switch. add /cul before frst dash in part number to order ul recognized switch. all solder lug models recognized at 3a @ 125/250v ac or 0.4va @ 28v ac/dc maximum.
series yb2 panel seal pushbuttons www.nkk.com d115 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt 22mm and 24mm pushbuttons with the shortest above-panel dimension (1.8mm) in the industry for splashproof design. meets ip65 of iec60529 standards (similar to nema 4 and 13), providing dust tight and splashproof panel seal protection. tamper resistant 19mm diameter actuator and 18mm square actuator. short body of .965 (24.5mm) conserves behind-panel space. distinctive long stroke and light touch actuation for clear indication of circuit status. choice of cap colors includes clear, red, green, amber, or metallic silver for enhanced panel appearance. metallic silver cap option has bright ring illumination (round only). brilliant illumination with multiple led colors. bezel color options in silver or black. available in momentary and alternate action with latchdown. crisp actuation and clear circuit status provided by snap-action contact mechanism. arc barrier protects against crossover. combination solder lug and .110 quick connect terminals. terminals are epoxy sealed to lock out fux, dust, solvents, and other contaminants, as well as to secure terminals and improve contact stability. custom legends on actuator available. distinctive characteristics actual size (round) actual size (square)
series yb2 panel seal pushbuttons www.nkk.com d116 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles typical switch ordering example 1 c k 01 led cap with clear lens & white diffuser with panel seal silver contacts with 3 amp rating solder lug/.110 (2.8mm) quick connect terminals white, super bright led black bezel round black housing spdt on-(on) circuit 5 description for typical ordering example YB215CWCKW01-6B-JB w c w yb2 poles 1 spdt 2 dpdt contact point c normally open and normally closed shape c round s square circuits 5 on (on) ( ) = momentary 6 on on alternate action with latchdown panel seal w with panel seal bezel k black s metallic silver contact materials & ratings w silver rated 3a @ 125v ac g gold rated 0.4va maximum @ 28v ac/dc maximum terminals 01 solder lug/.110 (2.8mm) quick connec t * * wire harness & cable assemblies offered only in americas important: switches are supplied without culus marking unless specifed. culus recognized only when ordered with marking on the switch. specifc models, ratings, & ordering in - structions are noted on general specif - cations page.
series yb2 panel seal pushbuttons www.nkk.com d117 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt 6 b jb super bright led 6b white 6f green 6g blue bright led led colors resistor no code no resistor (not for green) 05 5-volt 12 12-volt 24 24-volt 5c red 5d amber 5f green cap color s metallic silver jb clear/white cb red/white eb yellow/white fb green/white nonilluminated n no lamp cap types & colors leds typical switch ordering example lens/diffuser cap colors jb clear/white js metallic silver cap/clear ring (round only) lens/diffuser colors jb clear/white js metallic silver cap/clear ring (round only) cb red/white eb yellow/white fb green/white led & cap need to be the same color. yellow cap pairs with amber led to achieve amber illumination. codes jb & js (round only) may be combined with all led colors. led cap with clear lens & white diffuser with panel seal silver contacts with 3 amp rating solder lug/.110 (2.8mm) quick connect terminals white, super bright led metallic silver bezel square black housing spdt on-(on) circuit description for typical ordering example yb215cwssw01-6b-jb
series yb2 panel seal pushbuttons www.nkk.com d118 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles plunger position ( ) = momentary connected terminals throw & switch/lamp schematics pole model normal down normal down notes: switch is marked with nc, no, com, l+, lC. lamp circuit is isolated and requires an external power source. sp yb215 yb216 on on (on) on 1-3 1-2 spdt dp yb225 yb226 on on (on) on 1-3 4-6 1-2 4-5 dpdt l (+) (-) l l (+) (-) l silver contacts power level: 3a @ 125/250v ac switch base is green k black w panel seal (round and square) solder lug/ .110 (2.8mm) quick connect c round 01 (7.3) .288 epoxy seal (2.0) .079 (1.2) .047 (2.8) .110 thk = (0.5) .020 s metallic silver c normally open and normally closed gold contacts logic level: 0.4va max. @ 28v ac/dc max. switch base is red 4 6 nc 1 3 nc 2 no 5 no (com) 1 3 nc 2 no (com) contact points are both normally open and normally closed. two o-rings provide panel seal protection meeting ip65 of iec60529 standards. poles & circuits contact point panel seal shape bezel contact materials & ratings terminals w g s square
series yb2 panel seal pushbuttons www.nkk.com d119 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt bright & super bright leds at634 5-volt, 2-element with resistor at634 12-volt, 4-element with resistor electrical specifcations for bright green led with resistor unit forward peak current i fm ma typical forward current i f 11 9.5 8.7 ma forward voltage v f 5 12 24 v reverse peak voltage v rm 5 5 5 v current reduction rate above 25c ?i f ma/c ambient temperature range C25 ~ +50 c colors available: 5f green the electrical specifcations shown are determined at a basic temperature of 25c. led circuit is isolated and requires an external power source. if the source voltage exceeds the rated voltage, a ballast resistor is required. base of at634 and at636 is black for 5v, light blue for 12v and gray for 24v. bright at636 bright at634 t-1 1 ? 4 bi-pin t-1 1 ? 4 bi-pin (-) (+) (+) (-) (+) (-) at634 24-volt, 4-element with resistor electrical specifcations for bright red & amber led with resistor unit forward peak current i fm ma typical forward current i f 25 20 10 ma forward voltage v f 5 12 24 v reverse peak voltage v rm 4 8 16 v current reduction rate above 25c ?i f ma/c ambient temperature range C25 ~ +50 c colors available: 5c 5d red amber 05 12 24 05 12 24 electrical specifcations for bright led without resistor unit led colors red amber forward peak current i fm 40 40 ma typical forward current i f 26 26 ma forward voltage v f 1.9 2.0 v reverse peak voltage v rm 4 4 v current reduction rate above 25c ?i f 0.50 ma/c ambient temperature range C25 ~ +50 c no code colors available: 5c 5d red amber (+) (-) bright at628 t-1 bi-pin no resistor electrical specifcations for super bright led forward peak current i fm 30 30 30 ma typical forward current i f 20 20 20 ma forward voltage v f 3.6 3.5 3.6 v reverse peak voltage v rm 5 5 5 v current reduction rate above 25c ?i f 0.50 ma/c ambient temperature range C25 ~ +50 c colors: super bright at625g blue at631b white at632f green t-1 bi-pin 6b 6f 6g unit white green blue (+) (-) (-) (+) (-) (+) 5v 12v & 24v a ttention electrostatic sensitive devices a ttention electrostatic sensitive devices
series yb2 panel seal pushbuttons www.nkk.com d120 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles .748 (19.0) dia (13.1) .516 (4.9) .193 v f i f r + ? e anode cathode r = e ? v f i f where: r e v f i f = resistor v alue (ohms) = source v oltage (v) = for ward v oltage (v) = for ward current (a) cb eb fb lens/diffuser colors available: green/white * yellow/white red/white material for lens & diffuser: polycarbonate caps & cap colors at3017 cap for bright led at3018 cap for super bright led at3019 cap for nonilluminated jb clear/white s metallic silver lens/diffuser colors available: cap color available: note: at3017 cap can also be used without illumination. .748 (19.0) dia (13.1) .516 (4.9) .193 .748 (19.0) dia (13.1) .516 (4.9) .193 ballast resistor calculation for leds if the source voltage is greater than the rated voltage of a lamp or led, a ballast resistor must be connected in series with the lamp. this circuit diagram and formula will assist in calculating the value of the required ballast resistor. jb clear/white .748 (19.0) dia (13.1) .516 (4.9) .193 at3020 cap with illumination ring for bright or super bright led cap color available: js metallic silver with clear ring materials lens: polycarbonate insert: polyester * yellow cap pairs with amber led to achieve amber illumination. lens/diffuser colors available: fb green/white for bright led only eb * yellow/white for bright led only cb red/white for bright led only material for lens & diffuser: polycarbonate at3025 cap for illuminated at3027 cap for nonilluminated s metallic silver cap color available: note: at3025 cap can also be used without illumination. * yellow cap pairs with amber led to achieve amber illumination. jb clear/white for bright & superbright leds .709 (18.0) sq (13.1) .516 (4.9) .193 .709 (18.0) sq (13.1) .516 (4.9) .193
series yb2 panel seal pushbuttons www.nkk.com d121 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt typical switch dimensions single pole double pole YB215CWCKW01-6B-JB panel thickness & cutout panel thickness .020 ~ .197 (0.5mm ~ 5.0mm) (33.6) 1.323 (7.3) .288 (1.8) .071 m16 p1 (2.8) .110 ty p (0.5) .020 ty p (1.2) x (2.0) ty p .047 x .079 (24.5) .965 (3.7) .146 (9.7) .382 (3.0) .118 (5.55) .219 1 2 3 nc com no no l - + (3.7) .146 (9.7) .382 (6.0) .236 (11.1) .437 1 2 3 nc com no n o 4 6 5 l - + side-by-side mounting (25.0) .984 (19.0) .748 dia dia (25.4) min 1.00 (10.5) .413 (1.7) ty p .067 (22.0) .866 diat yp + 0.3 ? 0.0 (25.4) min 1.00 single pole yb215cwssw01-6b-jb panel thickness .020 ~ .197 (0.5mm ~ 5.0mm) side-by-side mounting .827 typ (21.0) + .012 (0.3) 0 .965 typ (24.5) double pole (33.6) 1.323 (7.3) .288 (1.8) .071 m16 p1 (2.8) .110 ty p (0.5) .020 ty p (1.2) x (2.0) ty p .047 x .079 (24.5) .965 (11.1) .437 (6.0) .236 (3.7) .146 (9.7) .382 (2.8) .110 (5.55) .219 (3.0) .118 (3.7) .146 (9.7) .382 (2.8) .110 (24.0) .945 (18.0) .709 sq sq
series yb2 panel seal pushbuttons www.nkk.com d122 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles 1. remove knurled mounting nut. 2. remove bezel and red o-ring from housing. there are two o-rings in this assembly: one is red, one is orange. 4. align tabs (b) on both sides of actuator with the projections (a) inside of the housing and push actuator frmly down to snap in. 5. install the red o-ring which was removed in step 2 at the inside bottom of the bezel. 6. align tab inside of the bezel with keyway on housing and bring bezel back into its original position. 7. before installing into panel, make sure that the orange o-ring is present at the back of the bezel. align keyway on bezel with tab in panel and push switch all the way into the panel. 8. attach mounting nut behind panel and tighten. make sure that bezel and actuator ft properly and that there is no space between bezel and panel. do not overtighten. mounting torque: 0.785nm (6.95 lb ? in) maximum. optional socket wrench at106 available. at106 socket wrench 3. install led. leds at634 & at636 led at628 leds at625g, at631b, at632f align d-fat on led with part number on switch for appropriate polarity and insert led into base. align d-fat on led with part number on switch for appropriate polarity and insert led into base. knurled mounting nut red o-ring bezel part number this side cathode socket (?) anode socket (+) (+) (?) (+) (?) d-flat (+) (?) d-flat anode (+) cathode (?) actuator b housing a the larger metal part within the led represents the cathode (C). align led for appropriate polarity and insert led into base. red o-ring bezel housing red o-ring keyway ta b bezel orange o-ring keyway ta b panel back of bezel bezel actuator knurled mounting nut panel bezel a ttention electrostatic sensitive devices a ttention electrostatic sensitive devices round assembly instructions
series yb2 panel seal pushbuttons www.nkk.com d123 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt square assembly instructions 1. remove knurled mounting nut. 2. remove bezel and blue o-ring from housing. 4. align tabs (b) on both sides of actuator with the projections (a) inside of the housing and push actuator frmly down to snap in. 5. install the blue o-ring which was removed in step 2 at the inside bottom of the bezel. 6. align tab inside of the bezel with keyway on housing and bring bezel back into its original position. 7. before installing into panel, make sure that the square gasket is present at the back of the bezel. align keyway on bezel with tab in panel and push switch all the way into the panel. 8. attach mounting nut behind panel and tighten. make sure that bezel and actuator ft properly and that there is no space between bezel and panel. do not overtighten. mounting torque: 0.785nm (6.95 lb ? in) maximum. optional socket wrench at106 available. 3. install led. leds at634 & at636 led at628 leds at625g, at631b, at632f align d-fat on led with part number on switch for appropriate polarity and insert led into base. align d-fat on led with part number on switch for appropriate polarity and insert led into base. part number this side cathode socket (?) anode socket (+) (+) (?) (+) (?) d-flat (+) (?) d-flat anode (+) cathode (?) the larger metal part within the led represents the cathode (C). align led for appropriate polarity and insert led into base. a ttention electrostatic sensitive devices a ttention electrostatic sensitive devices spacer bezel blue o-ring b a housing actuator bezel blue o-ring bezel housing keyway ta b panel bezel back of bezel actuator bezel panel knurled nut spacer at106 socket wrench
series yb2 panel seal pushbuttons www.nkk.com d124 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles recommended methods: laser etch on clear cap, screen print or pad print on cap. epoxy based ink is recommended. shaded area is printable area for caps at3017, at3018, and at3019 (17.48) dia .688 (19.0) dia .748 (0.76) ty p .030 leds are electrostatic sensitive devices. when installing and handling leds, use an electrostatic protected work station to prevent led damage. handling & precautions legends (19.0) dia .748 (1.56) ty p .062 (15.88) dia .625 shaded area is printable area for cap at3020 (with clear ring for illumination) a ttention electrostatic sensitive devices nkk switches can provide custom legends for caps. contact factory for more information. +(0.08) .0031 ? (0.1) .0039 (17.4) .685 (15.88) .625 (0.76) ty p .030 (16.3) .642 (14.78) .582 (0.1) .0039 +/? (1.2) ty p .047 (0.6) r ty p .024 +(0.08) .0031 ? (0.1) .0039 shaded area is printable area for film inserts film material and thickness: clear polyester, 4 mil max. recommended print method: screen print; epoxy based ink is recommended (15.88) sq .625 (17.4) sq .685 (0.76) typ .030 (18.0) sq .709 (16.48) sq .649 (0.76) ty p .030 shaded area is printable area for caps at3025 and at3027

▲Up To Search▲

Price & Availability of YB215CWCKW01-6B-JB

	To Download YB215CWCKW01-6B-JB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .