ilpa35jud series 35w dimmable water - proof constant current led driver C wide input voltage 90 to 305vac, 47 to 63hz C dimming control, constant current output C over voltage, short circuit, lighting, and over temperature protection C high efficiency (up to 88%) C active power factor correction (pfc) C ip67 waterproof rating, metal housing C comply with ul8750 & en61347 safety regulation 3 year warranty approvals: single output part number output current range (min. / typ. / max.) output voltage range (min. / max.) efficiency (220vac, full load) over voltage protection (min/typ/max) max. output power ilpa35jud - s290dt 2755 / 2900 / 3045 ma 4 / 12 vdc 82% 13 / 15 / 17 vdc 35w ilpa35jud - s245dt 2328 / 2450 / 2573 ma 5 / 15 vdc 83% 16 / 18 / 20 vdc 35w ilpa35jud - s210dt 1995 / 2100 / 2205 ma 6 / 18 vdc 84% 19 / 21 / 23 vdc 35w ilpa35jud - s175dt 1663 / 1750 / 1838 ma 7 / 20 vdc 84% 23 / 25 / 27 vdc 35w ilpa35jud - s140dt 1330 / 1400 / 1470 ma 8 / 24 vdc 85% 30 / 32 / 34 vdc 35w ilpa35jud - s105dt 998 / 1050 / 1103 ma 11 / 33 vdc 86% 39 / 41 / 43 vdc 35w ilpa35jud - s070dt 665 / 700 / 735 ma 17 / 50 vdc 86% 57 / 58 / 59 vdc 35w ilpa35jud - s045dt 428 / 450 / 473 ma 26 / 78 vdc 87% 95 / 97 / 99 vdc 35w ilpa35jud - s035dt 333 / 350 / 368 ma 33 / 100 vdc 88% 118 / 120 / 122 vdc 35w item - s290dt, - s245dt, - s210dt, - s175dt, - s140dt, - s105dt are class 2 output (usr & cnr). item - s070dt is class 2 output (usr), non - class 2 output (cnr) item - s045dt, - s035dt is non - class 2 output (usr & cnr) electrical characteristics parameter test conditions min. typ. max. unit input voltage operating voltage 90 305 vac input frequency 47 63 hz output power range vin=90 to 264vac 0 35 w input current (low line) io=full load, vin=115vac 0.49 a input current (high line) io=full load, vin=230vac 0.25 a high line inrush current io=full load, 25c, cool start, vin=230vac 20 a power factor correction vin=110vac 92 % efficiency io=full load, vin=230vac 82 88 % no - load power consumption no load, vin=230vac 6 w line regulation io=full load 2 % load regulation vin=230vac 5 % over voltage protection (latch mode. the power unit shall return to normal operation only after the power is turn - on again.) over temperature protection 110 c short circuit protection no damage shall occur when any output operating in a short circuit condition. the power supply shall be self - recovery when the fault condition is removed. output overshoot / undershoot when power on or off 10 % start up time io=full load, vin=110vac 1.7 2 s ripple & noise (peak to peak) measured by 20 mhz bandwidth oscilloscope and the output paralleled a 0.1 uf ceramic capacitor and a 10 uf electrolytic capacitor. 10 % vo
conditions parameter test conditions min. typ. max. unit operating temperature humidity: 10% rh to 100% rh - 35 55 c storage temperature humidity: 5% rh to 100% rh - 40 85 c mtbf (operation temperature at 25c, calculated per mil - hdbk - 217f ) 0.541m hours life time (measured at 110vac, 45c ambient temperature, 80% load for 2900ma output model) 0.087m hours no output power derating from - 35c to 55c approvals and compliance parameter standards emi en55015 ems en61000 - 3 - 2, en61000 - 3 - 3, en61000 - 4 - 2, en61000 - 4 - 3 , en61000 - 4 - 4, , en61000 - 4 - 5, en61000 - 4 - 6, en61000 - 4 - 8, en61000 - 4 - 11, en61547 safety ul/c - ul, ce ul8750 compliant to ul1310 class 2, ul1012, ul935, csa - c22.2 no. 0, csa - c22.2 no. 107.1, csa - c22.2 no.250.0, en61347 - 1,en61347 - 2 - 13 waterproof ip67 rating mechanical parameter specification dimension, 172x34.5x42.5mm (6.77x1.36x1.67 inches) net weight 480g dimming control parameter min. typ. max. unit 10v output voltage 9.8 10v 10.2 vdc 10v output source current - 10 - 2 ma absolute max. voltage on the 1~10v input pin - 2 - 15 vdc source current on 0 - 10v input pin 0 - 1 ma the dimmer control may be operated from either a potentiometer or from an input signal of 0 ~ 10 vdc. two recommended impleme ntations are provided above notes: 1. for the driver to operate properly, the load voltage must be maintained above the minimum voltage threshold (approx. 33% of the max. output voltage for any given model). 2. if the input voltage is within 90 - 175vac, the output current can be varied from 100% down to 10%. (refer to right figure a ) 3. if the input voltage is within 175 - 305vac, the output current can be varied from 100% down to 20%. (refer to right figure b )
|
