 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 49:8;):/54 #.++: !-()0'%0/)2
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figure 1 ! undercarpet procrimper iii hand tool assembly 913921 is used to crimp the connectors listed in figure 1. read these instructions thoroughly before using the tool assembly. reasons for reissue of this instruction sheet are provided in section 6, revision summary. /-;8+ the tool assembly consists of a frame and anvil die. the frame features a stationary jaw and handle, a moving jaw and handle, a handle stop, and a ratchet that ensures full crimping. the stationary jaw holds the anvil die. a die retaining screw is used to secure the die. when closed, the die and moving jaw forms a crimping chamber. ! refer to figure 1, and select cable of the specified size and connector for the type of application, and proceed as follows: 1. separate the conductors of the cable along the perforations to the dimensions given in figure 2. # & &% ( # $$! '' " !) # $ ! ! figure 2 ! ! "! ! ! ! "! ! 2. hold the tool so that the flat side of the head is parallel with the floor. see figure 3. 3. gently lift the cable and straddle the tool jaws with between the conductor and the connector. refer to figure 3. 4. squeeze the tool handles together until one handle bottoms on the handle stop. 5. allow the handles to open fully, the tool from the connector. 6. repeat steps 2 through 5 as necessary for one side of the cable. #( ## ensure that the tool frame and die are clean by wiping them with a clean, soft cloth. remove any debris with a clean, soft brush. do not use objects that could damage any components. when not in use, keep tool handles closed to prevent objects from becoming lodged in the die and moving jaw, and store in a clean, dry area. figure 3 *#$-" -,$/ *# ++( ..$)!(1 *# "0 1 * '" .,*)& - *,+*, .&*) figure 4 &( &( &) &) 1+ 1+ +/$ *. .* '" '"("). --"! *(+'"."'1 %,*/$% ,&(+&)$ % ( ", '"("). ).","! ,.& ''1 &).* /. /-. *. -- *(+'"."'1 %,*/$% ,&(+&)$ % ( ", '.0 ( *.,$"/'+* the die and moving jaw should be inspected on a regular basis to ensure it has not become worn or damaged. inspect the crimping surfaces for flattened, chipped, worn, or broken areas. if damage or abnormal wear is evident, the tool must be replaced. see section 5, replacement. ++( (+.0-$ *.,$"/'+* squeeze the tool handles together until one handle bottoms on the handle stop. the die and moving jaw should bottom properly, and the crimping chamber should conform to the gaging inspection described in paragraph 4.3. %'*% /&$ -'),'*% & )!$- this inspection requires the use of a plug gage conforming to the dimensions provided in figure 4. to gage the crimping chamber, proceed as follows: 1. remove traces of oil or dirt from the crimping chamber and plug gage. 2. close the tool handles until one handle bottoms on the handle stop; then hold in this position. do not force beyond initial contact. 3. insert go element into the crimping chamber; but do not force it. the go element must pass completely through the length of the crimping chamber. 4. in the same manner, try to insert the nogo element into the crimping chamber. the nogo element may enter partially, but must not pass completely through the length of the crimping chamber. if the crimping chamber conforms to the gage inspection, the tool may be considered dimensionally correct and should be lubricated with a thin coat of any good sae 20 motor oil. if the crimping chamber does not conform to the gage inspection, the tool must be repaired. available separately, repair kit 6792211 includes a replacement lock nut and a variety of pins, rings, screws, and springs. if the die is damaged or worn excessively, it must be replaced. order the repair kit and replaceable parts through your representative, or call 18005265142, or send a facsimile of your purchase order to 7179867605, or write to: customer service (038035) tyco electronics corporation po box 3608 harrisburg pa 171053608 initial release of document |
Price & Availability of 91392-1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |