![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
rp131x series low on resistance / low voltage 1a ldo no.ea-174-160426 1 outline the rp131x series are voltage-regulators with a built-in low on-resistance transistor and output current is 1a capability. these ics are capable of the low input volt age (min.1.6v) and also the minimum output voltage can be set from 0.8v. (the output voltage is fixed in the ic.) each of these ics consists of a voltage reference unit, an er ror amplifier, a resistor net for setting output voltage, a chip enable circuit, current limit circuits for ov er-current and short, and a thermal-shutdown circuit. a standby mode with ultra low supply current can be realized with the chip enable function. the packages for these ics are dfn1616-6b and dfn(plp) 1820-6 which are suitable for high density mounting of the ics on boards. sot-89-5, hsop-6j and to-252-5-p 2 with high power dissipation are also available. features ? output current ............................................................ min. 1a ? supply current ............................................................. typ. 65 a ? standby current ......................................................... typ. 0.15 a ? input voltage range ................................................... 1.6v to 6.5v ? output voltage range .................................................. 0.8v to 5.5v (0.1v steps) ( for other voltages, please re fer to mark informations.) ? dropout voltage ............................................................ typ. 0.5v (v out = 2.8v, i out = 1a) ? ripple rejectio n ........................................................... typ. 70db (f = 1khz, v out = 2.8v) ? output voltage accuracy .............................................. 1.0% ? temperature-drift coefficien t of output voltage .......... typ. 100ppm/ c ? line regulation ............................................................ typ. 0.05%/v ? load regulati on ......................................................... typ. 20mv at i out = 300ma, typ. 80mv at i out = 1a ? packages ............................................................... dfn1616- 6b, dfn(plp)1820-6, sot-89-5, hsop-6j, to-252-5-p2 ? built-in inrush current lim it circuit ............................... typ. 500ma ? built-in fold-back protection circuit ........................... typ. 250ma (current at short mode) ? built-in thermal shutdown circuit .............................. ther mal shutdown temperature ; typ. 165 c released temperature ; typ. 135 c ? built-in auto discharg e function ................................ d version ? ceramic capacitors are recommend ed to be used with this ic .... 2.2 f or more (v out 3.6v) 4.7 f or more (v out > 3.6v) applications ? power source for battery-powered equipment. ? power source for portable communication equipment. ? power source for electrical appliances such as cameras, vcrs and camcorders. ? power source for notebook pc. ? power source for home appliances.
rp131x no.ea-174-160426 2 block diagrams rp131xxx1b rp131xxx1d v dd gnd v out ce vref current limit thermal shutdown v dd gnd v out ce vref current limit thermal shutdown selection guide the output voltage, auto discharge func tion, package for the ics can be selected at the user?s request. product name package quantity per reel pb free halogen free rp131lxx1 ? -tr dfn1616-6b 5,000 pcs yes yes rp131kxx1 ? -tr dfn(plp)1820-6 5,000 pcs yes yes rp131hxx1 ? -t1-fe sot-89-5 1,000 pcs yes yes rp131sxx1 ? -e2-fe hsop-6j 1,000 pcs yes yes rp131jxx1 ? -t1-fe to-252-5-p2 3,000 pcs yes yes xx : ? : the output voltage can be designated in the range fr om 0.8v(08) to 5.5v(55) in 0.1v steps. (for other voltages, please refer to mark informations.) the auto discharge function at off state are options as follows. (b) without auto discharge function at off state (d) with auto discharge function at off state rp131x no.ea-174-160426 3 pin configurations ? dfn1616-6b ? dfn(plp)1820-6 top view 3 4 2 5 1 6 bottom view 1 6 2 5 3 4 ? top view 6 54 123 bottom view 4 5 6 3 2 1 ? 1 z sot-89-5 z hsop-6j z to-252-5-p2 1 3 5 4 2 13 64 2 5 1 2 3 4 5 pin descriptions ? dfn1616-6b pin no. symbol pin description 1 v out output pin ? 2 2 v out output pin ? 2 3 gnd ground pin 4 ce chip enable pin ("h" active) 5 v dd input pin ? 2 6 v dd input pin ? 2 ? 1) tab is gnd level. (they are connected to the reverse side of this ic.) the tab is better to be connected to the gn d, but leaving it open is also acceptable. ? 2) when you use this ic, please make sure be wired with 1pin with 2pin and 5pin with 6pin. rp131x no.ea-174-160426 4 ? dfn(plp)1820-6 pin no. symbol pin description 1 v out output pin ? 2 2 v out output pin ? 2 3 gnd ground pin 4 ce chip enable pin ("h" active) 5 v dd input pin ? 2 6 v dd input pin ? 2 ? 1) tab is gnd level. (they are connected to the reverse side of this ic.) the tab is better to be connected to the gn d, but leaving it open is also acceptable. ? 2) when you use this ic, please make sure be wired with 1pin with 2pin and 5pin with 6pin. ? sot-89-5 pin no. symbol pin description 1 nc no connection 2 gnd ground pin 3 ce chip enable pin ("h" active) 4 v dd input pin 5 v out output pin ? hsop-6j pin no. symbol pin description 1 v out output pin 2 gnd ground pin ? 3 3 nc no connection 4 ce chip enable pin ("h" active) 5 gnd ground pin ? 3 6 v dd input pin ? 3) when you use this ic, please make sure be wired with 2pin and 5pin. ? to-252-5-p2 pin no. symbol pin description 1 v out output pin 2 gnd ground pin ? 4 3 gnd ground pin ? 4 4 ce chip enable pin ("h" active) 5 v dd input pin ? 4) when you use this ic, please make sure be wired with 2pin and 3pin. rp131x no.ea-174-160426 5 absolute maximum ratings symbol item rating unit v in input voltage 7.0 v v ce input voltage (ce pin) ? 0.3 to 7.0 v v out output voltage ? 0.3 to v in + 0.3 v p d power dissipation (dfn1616-6b) ? 640 mw power dissipation (dfn(plp)1820-6) ? 880 power dissipation (sot-89-5) ? 900 power dissipation (hsop-6j) ? 1700 power dissipation (to-252-5-p2) ? 1900 t opt operating temperature range ? 40 to 85 c t stg storage temperature range ? 55 to 125 c ? ) for power dissipation, please refer to package information. absolute maximum ratings electronic and mechanical stress momentarily exceeded absolute maximum ratings may cause the permanent damages and may degrade the life time and safe ty for both device and sy stem using the device in the field. the functional operation at or over these absolute maximum ratings is not assured. rp131x no.ea-174-160426 6 electrical characteristics v in = set v out + 1v, i out = 1ma the specification in is checked and guaranteed by design engineering at ? 40 c t opt 85 c, unless otherwise noted. ? rp131xxx1b/d topt = 25 c symbol item conditions min. typ. max. unit v out output voltage t opt = 25 c v out >1.5v 1.01 1.5v ? ? 40 c t opt 85 c v out >1.5v 0.974 1.018 v v out 1.5v ? 40 27 v out / i out load regulation 0.1ma i out 300ma 20 40 mv 0.1ma i out 1a 80 120 v dif dropout voltage refer to the following table i ss supply current i out = 0ma (v in = 6.5v) 65 90 a i standby standby current v ce = 0v, v in = 6.5v 0.15 0.60 a v out / v in line regulation set v out + v in 6.5v ? however, v in 1.6v 0.05 0.1 %/v rr ripple rejection f = 1khz ripple 0.2vp-p i out = 100ma v out 3.3v 70 db v out >3.3v 60 v in input voltage 1.6 6.5 v v out / t opt output voltage temperature coefficient ? 40 c t opt 85 c 100 ppm / c i lim output current limit 1 a i sc short current limit v out = 0v 250 ma i pd ce pull-down current 0.3 a v ceh ce input voltage "h" 1.0 v v cel ce input voltage "l" 0.4 v en output noise bw = 10hz to 100khz, i out = 1ma 45 vrms c t tsr thermal shutdown released temperature junction temperature 135 c r low low output nch tr. on resistance (of d version) v in = 4.0v, v ce = 0v 30 the specification in is checke d and guaranteed by design engineering at ? 40 c t opt 85 c, unless otherwise noted. all of unit are tested and specified under load conditions such that tj t opt = 25c except for output noise, ripple rejection, output voltage temperature coefficien t, dropout voltage at 1a ou tput current and thermal shutdown items. rp131x no.ea-174-160426 7 ? dropout voltage by output voltage topt = 25c output voltage v out (v) dropout voltage v dif (v) condition typ. max. condition typ. max. 0.8 v out < 0.9 i out = 300ma 0.600 0.780 i out = 1a 1.100 1.650 0.9 v out < 1.0 0.550 0.690 1.050 1.500 1.0 v out < 1.1 0.450 0.610 1.000 1.450 1.1 v out < 1.2 0.340 0.540 0.930 1.420 1.2 v out < 1.5 0.290 0.500 0.900 1.380 1.5 v out < 2.6 0.230 0.310 0.700 1.100 2.6 v out < 3.3 0.150 0.180 0.500 0.750 3.3 v out 5.5 0.140 0.170 0.450 0.650 the specification in is checke d and guaranteed by design engineering at ? 40 c t opt 85 c, unless otherwise noted. all of unit are tested and specified under load conditions such that tj t opt = 25c except for output noise, ripple rejection, output voltage temperature coefficien t, dropout voltage at 1a ou tput current and thermal shutdown items. recommended operating conditions (electrical characteristics) all of electronic equipment should be designed that the mounted semiconductor devices operate within the recommended operating conditions. the semiconductor devices cannot operate normally over the recommended operating conditions, even if when they are used over such conditions by momentary electronic noise or surge. and the semiconductor devices may receive seriou s damage when they conti nue to operate over the recommended operating conditions. rp131x no.ea-174-160426 8 typical application c1 rp131x series v dd v out ce gnd c2 v out recommendation value of the external capacitors v out capacitors v out 3.6v c1 kyocera 2.2 f (size:1005) [cm05x5r225m06ab] c2 kyocera 2.2 f (size:1608) [cm105x5r225k06ab] v out > 3.6v c1 kyocera 2.2 f (size:1608) [cm105x5r225k06ab] c2 kyocera 4.7 f (size:1608) [cm105x5r475m06ab] technical notes when using these ics, consider the following points: phase compensation in these ics, phase compensation is made for securing stable operation even if the load current is varied. for this purpose, use a capacitor c2 with good frequency ch aracteristics and esr (equivalent series resistance). if a tantalum capacitor is used, and its esr of c2 is large, the loop oscillati on may result. because of this, select c2 carefully considering its frequency characteristics. pcb layout make v dd and gnd lines sufficient. if their impedance is hi gh, noise pickup or unstable operation may result. connect a capacitor c1 between v dd and gnd pin with a capacitance value as "recommendation value of the external capacitors" above or more, and as close as possible to the pins. set external components, especially t he output capacitor c2, as close as possible to the ics, and make wiring as short as possible. rp131x no.ea-174-160426 9 test circuits c1 rp131x series v dd v out ce gnd v c2 v out i out basic test circuit c1 v dd v out ce gnd c2 a i ss v out rp131x series test circuit for supply current rp131x series v dd v out ce gnd c2 pulse generator i out p. g. test circuit for ripple rejection i outa i outb c1 rp131x series v dd v out ce gnd c2 v out test circuit for load transient response rp131x no.ea-174-160426 10 typical characteristics 1) output voltage vs. output current (t opt = 25 c) rp131x081x rp131x151x rp131x331x rp131x501x 2) output voltage vs. input voltage (t opt = 25 c) rp131x081x rp131x151x 0 1.5 1.0 0.5 2.0 output current i out (a) output voltage v out (v) 0 0.9 0.5 0.4 0.3 0.6 0.7 0.8 0.2 0.1 v in =1.4v v in =1.6v v in =2.0v v in =2.5v v in =2.8v 0 1.5 1.0 0.5 2.0 output current i out (a) output voltage v out (v) 0 1.6 1.0 0.8 0.6 1.2 1.4 0.4 0.2 v in =2.0v v in =2.5v v in =3.5v 0 1.5 1.0 0.5 2.0 output current i out (a) output voltage v out (v) 0 3.5 2.5 2.0 1.5 3.0 1.0 0.5 v in =3.6v v in =4.3v v in =5.0v 0 1.5 1.0 0.5 2.0 output current i out (a) output voltage v out (v) 0 5.5 3.5 2.5 1.5 4.5 4.0 3.0 2.0 5.0 1.0 0.5 v in =5.3v v in =6.0v 045 3 2 16 input voltage v in (v) output voltage v out (v) 0 1.0 0.6 0.4 0.3 0.8 0.7 0.5 0.9 0.2 0.1 i out =1ma i out =50ma i out =100ma i out =300ma 045 3 2 16 input voltage v in (v) output voltage v out (v) 0 1.8 1.2 0.9 1.5 0.6 0.3 i out =1ma i out =50ma i out =100ma i out =300ma rp131x no.ea-174-160426 11 rp131x331x rp131x501x 3) supply current vs. input voltage (t opt = 25 c) rp131x081x rp131x151x rp131x331x rp131x501x 045 3 2 16 input voltage v in (v) output voltage v out (v) 0 3.5 2.0 1.5 2.5 3.0 1.0 0.5 i out =1ma i out =50ma i out =100ma i out =300ma 045 3 2 16 input voltage v in (v) output voltage v out (v) 0 6 4 3 5 2 1 i out =1ma i out =50ma i out =100ma i out =300ma 045 3 2 16 input voltage v in (v) supply current i ss ( a) 0 70 50 30 60 40 20 10 045 3 2 16 input voltage v in (v) supply current i ss ( a) 0 70 50 30 60 40 20 10 045 3 2 16 input voltage v in (v) supply current i ss ( a) 0 70 50 30 60 40 20 10 045 3 2 16 input voltage v in (v) supply current i ss ( a) 0 70 50 30 60 40 20 10 rp131x no.ea-174-160426 12 4) output voltage vs. temperature rp131x081x rp131x281x rp131x331x rp131x501x 5) supply current vs. temperature rp131x081x rp131x151x 0.76 0.83 0.77 0.78 0.80 0.82 0.79 0.81 -40 75 50 025 -25 85 temperature topt ( c) output voltage v out (v) 1.46 1.53 1.47 1.48 1.50 1.52 1.49 1.51 -40 75 50 025 -25 85 temperature topt ( c) output voltage v out (v) 3.20 3.36 3.22 3.24 3.28 3.32 3.34 3.26 3.30 -40 75 50 025 -25 85 temperature topt ( c) output voltage v out (v) 4.90 5.06 4.92 4.94 4.98 5.02 5.04 4.96 5.00 -40 75 50 025 -25 85 temperature topt ( c) output voltage v out (v) 0 90 10 20 40 70 30 50 80 60 -40 75 50 025 -25 85 temperature topt ( c) supply current i ss ( a) 0 90 10 20 40 70 30 50 80 60 -40 75 50 025 -25 85 temperature topt ( c) supply current i ss ( a) rp131x no.ea-174-160426 13 rp131x331x rp131x501x 6) dropout voltage vs. output current rp131x081x rp131x151x rp131x331x rp131x501x 0 90 10 20 40 70 30 50 80 60 -40 75 50 025 -25 85 temperature topt ( c) supply current i ss ( a) 0 90 10 20 40 70 30 50 80 60 -40 75 50 025 -25 85 temperature topt ( c) supply current i ss ( a) 0 1.6 1.4 1.0 0.6 1.2 0.8 0.4 0.2 output current i out (ma) dropout voltage v dif (v) 85 c 25 c -40 c 0 800 200 400 600 900 300 500 700 100 1000 0 1.4 1.0 0.6 1.2 0.8 0.4 0.2 0 800 200 400 600 900 300 500 700 100 1000 output current i out (ma) dropout voltage v dif (v) 85 c 25 c -40 c 0 1.4 1.0 0.6 1.2 0.8 0.4 0.2 0 800 200 400 600 900 300 500 700 100 1000 output current i out (ma) dropout voltage v dif (v) 85 c 25 c -40 c 0 1.4 1.0 0.6 1.2 0.8 0.4 0.2 0 800 200 400 600 900 300 500 700 100 1000 output current i out (ma) dropout voltage v dif (v) 85 c 25 c -40 c rp131x no.ea-174-160426 14 7) dropout voltage vs. set output voltage 8) ripple rejection vs. input bias voltage ( c1 = none, c2 = ceramic 1.0 f, ripple = 0.2v p-p , t opt = 25 c ) rp131x331x rp131x331x rp131x331x rp131x501x 1.2 0.6 1.0 0.8 0.4 0.2 0 0.7 1.1 0.9 0.5 0.3 0.1 0.5 5.5 3.5 4.5 1.5 2.5 set output voltage v reg (v) dropout voltage v dif (v) i out =50ma i out =10ma i out =1ma i out =0ma i out =600ma i out =400ma i out =200ma i out =100ma i out =1a i out =800ma 3.0 4.0 6.0 5.0 3.5 5.5 4.5 6.5 input voltage v in (v) 0 10 40 30 20 60 50 70 80 ripple rejection rr (db) i out =1ma f=0.2khz f=1khz f=10khz f=100khz 3.0 4.0 6.0 5.0 3.5 5.5 4.5 6.5 input voltage v in (v) 0 10 40 30 20 60 50 70 80 ripple rejection rr (db) i out =30ma f=0.2khz f=1khz f=10khz f=100khz 3.0 4.0 6.0 5.0 3.5 5.5 4.5 6.5 input voltage v in (v) 0 10 40 30 20 60 50 70 80 ripple rejection rr (db) i out =50ma f=0.2khz f=1khz f=10khz f=100khz 4.5 6.0 5.0 5.5 6.5 input voltage v in (v) 0 10 40 30 20 60 50 70 80 90 ripple rejection rr (db) i out =1ma f=0.2khz f=1khz f=10khz f=100khz rp131x no.ea-174-160426 15 rp131x501x rp131x501x 9) ripple rejection vs. frequency (c1 = none, c2 = ceramic 4.7 f, t opt = 25 c) rp131x081x rp131x151x rp131x331x rp131x501x 4.5 6.0 5.0 5.5 6.5 input voltage v in (v) 0 10 40 30 20 60 50 70 80 90 ripple rejection rr (db) i out =10ma f=0.2khz f=1khz f=10khz f=100khz 4.5 6.0 5.0 5.5 6.5 input voltage v in (v) 0 10 40 30 20 60 50 70 80 90 ripple rejection rr (db) i out =100ma f=0.2khz f=1khz f=10khz f=100khz i out =1ma i out =30ma i out =100ma 0 10 20 30 100 60 40 80 70 90 50 v in =1.8vdc+0.2vp-p frequency f (khz) ripple rejection rr (db) 0.1 10 100 1 1000 i out =1ma i out =30ma i out =100ma 0 10 20 30 100 60 40 80 70 90 50 v in =2.5vdc+0.2vp-p frequency f (khz) ripple rejection rr (db) 0.1 10 100 1 1000 i out =1ma i out =30ma i out =100ma 0 10 20 30 100 60 40 80 70 90 50 v in =4.3vdc+0.2vp-p frequency f (khz) ripple rejection rr (db) 0.1 10 100 1 1000 i out =1ma i out =30ma i out =100ma 0 10 20 30 100 60 40 80 70 90 50 v in =6.0vdc+0.2vp-p frequency f (khz) ripple rejection rr (db) 0.1 10 100 1 1000 rp131x no.ea-174-160426 16 10) input transient response (i out = 100ma, tr = tf = 5 s, c1 = none, t opt = 25 c) rp131x081x rp131x151x rp131x331x rp131x501x 11) load transient response (tr = tf = 0.5 s, c1 = ceramic 2.2 f, v in = v out +1.0v, t opt = 25 c) rp131x081x rp131x151x 40 60 20 10 080 50 70 30 90 output voltage v out (v) output voltage input voltage 1 2 0.79 0.80 0.81 input voltage v in (v) 3 time t ( s) c2=ceramic2.2 f 40 60 20 10 080 50 70 30 90 output voltage v out (v) output voltage input voltage 2 3 1.49 1.50 1.51 input voltage v in (v) 4 time t ( s) c2=ceramic2.2 f 40 60 20 10 080 50 70 30 90 output voltage v out (v) output voltage input voltage 4 5 3.29 3.30 3.31 input voltage v in (v) 6 time t ( s) c2=ceramic2.2 f 40 60 20 10 080 50 70 30 90 output voltage v out (v) output voltage input voltage 5 6 4.995 5.000 5.005 input voltage v in (v) 7 time t ( s) c2=ceramic4.7 f 90 50 70 output voltage v out (v) output voltage 0.78 0.80 0.81 0.79 110 time t ( s) output current output current i out (ma) 50ma 100ma c2=ceramic2.2 f 0 180 60 100 20 140 160 80 120 40 90 50 70 0 180 60 100 20 140 160 80 120 40 output voltage v out (v) output voltage 1.46 1.50 1.52 1.48 110 time t ( s) output current output current i out (ma) 50ma 100ma c2=ceramic2.2 f rp131x no.ea-174-160426 17 rp131x331x rp131x501x rp131x081x rp131x151x rp131x331x rp131x501x 90 50 70 0 180 60 100 20 140 160 80 120 40 output voltage v out (v) output voltage 3.27 3.29 3.30 3.31 3.32 3.33 3.28 110 time t ( s) output current output current i out (ma) 50ma 100ma c2=ceramic4.7 f 90 50 70 0 180 60 100 20 140 160 80 120 40 output voltage v out (v) output voltage 4.97 4.99 5.00 5.01 5.02 4.98 110 time t ( s) output current output current i out (ma) 50ma 100ma c2=ceramic4.7 f 0 20 0 180 60 100 20 140 160 80 120 40 output voltage v out (v) output voltage 0.76 0.78 0.80 0.82 40 time t ( s) output current output current i out (ma) 0ma 30ma c2=ceramic2.2 f 0 20 0 180 60 100 20 140 160 80 120 40 output voltage v out (v) output voltage 1.46 1.48 1.50 1.52 40 time t ( s) output current output current i out (ma) 0ma 30ma c2=ceramic2.2 f 0 20 0 180 60 100 20 140 160 80 120 40 output voltage v out (v) output voltage 3.26 3.28 3.30 3.32 40 time t ( s) output current output current i out (ma) 0ma 30ma c2=ceramic4.7 f 0 20 0 180 60 100 20 140 160 80 120 40 output voltage v out (v) output voltage 4.97 4.98 4.99 5.00 5.01 40 time t ( s) output current output current i out (ma) 0ma 30ma c2=ceramic4.7 f rp131x no.ea-174-160426 18 rp131x081x rp131x151x rp131x331x rp131x501x 12) turn on speed with ce pin (c1 = ceramic 2.2 f, c2 = ceramic 4.7 f, t opt = 25 c) rp131x081x rp131x501x 200 0 400 0 180 60 100 20 140 160 80 120 40 output voltage v out (v) output voltage 0.4 0.6 0.8 1.0 600 time t ( s) output current output current i out (ma) 100ma 500ma c2=ceramic2.2 f 200 0 400 0 180 60 100 20 140 160 80 120 40 output voltage v out (v) output voltage 1.1 1.3 1.5 1.7 600 time t ( s) output current output current i out (ma) 100ma 500ma c2=ceramic2.2 f 200 0 400 0 180 60 100 20 140 160 80 120 40 output voltage v out (v) output voltage 2.7 2.9 3.1 3.3 3.5 600 time t ( s) output current output current i out (ma) 100ma 500ma c2=ceramic4.7 f 200 0 400 0 180 60 100 20 140 160 80 120 40 output voltage v out (v) output voltage 4.6 4.8 5.0 5.2 600 time t ( s) output current output current i out (ma) 100ma 500ma c2=ceramic4.7 f 2 1 0 output voltage v out (v) output voltage ce input voltage 0 0.8 0.4 3 time t ( s) ce input voltage v ce (v) v in =1.8v i out =0ma i out =100ma 0 450 150 250 50 350 400 200 300 100 6 3 0 0 450 150 250 50 350 400 200 300 100 output voltage v out (v) output voltage ce input voltage 0 4 6 2 9 time t ( s) ce input voltage v ce (v) v in =6.0v i out =0ma i out =100ma rp131x no.ea-174-160426 19 13) turn off speed with ce pin (d version) (c1 = ceramic 2.2 f, c2 = ceramic 4.7 f, t opt = 25 c) rp131x081d rp131x501d 14) inrush current at turning on (c1 = ceramic 2.2 f, c2 = ceramic 4.7 f, t opt = 25 c) rp131x081x rp131x501x 15) minimum operating voltage rp131x081x 2 1 0 output voltage v out (v) output voltage ce input voltage 0 0.8 0.4 3 time t (ms) ce input voltage v ce (v) v in =1.8v i out =0ma i out =100ma 0 1.8 0.6 1.0 0.2 1.4 1.6 0.8 1.2 0.4 6 3 0 output voltage v out (v) output voltage ce input voltage 0 4 6 2 9 time t (ms) ce input voltage v ce (v) v in =6.0v i out =0ma i out =100ma 0 1.8 0.6 1.0 0.2 1.4 1.6 0.8 1.2 0.4 600 500 400 300 200 100 0 ce input voltage v ce (v) output voltage v out (v) output voltage inrush current ce input voltage 0 1.0 1.5 2.0 2.5 3.0 3.5 0.5 700 time t ( s) inrush current (ma) v in =2.3v 320 80 160 0 240 280 120 200 40 600 700 500 400 300 200 100 0 output voltage inrush current ce input voltage 0 2 3 4 5 7 6 8 1 800 time t ( s) inrush current (ma) v in =6.5v 320 80 160 0 240 280 120 200 40 ce input voltage v ce (v) output voltage v out (v) 0 200 800 400 600 1000 output current i out (ma) input voltage v in (v) 1.0 2.3 1.9 1.6 1.2 2.0 2.1 2.2 1.7 1.3 1.4 1.8 1.5 1.1 hatched area is available for 0.8v output. rp131x no.ea-174-160426 20 esr vs. output current when using these ics, consider the following points: the relations between i out (output current) and esr of an out put capacitor are shown below. the conditions when the white noise level is under 40 v (avg.) are marked as the hatched area in the graph. measurement conditions frequency band : 10hz to 3mhz temperature : ? 40 c to 85 c c1 : 2.2 f (kyocera, cm05x5r225m04ad) c2 : 2.2 f (kyocera, cm105x5r225k06ae) 4.7 f (kyocera, cm105x5r475m06ab) rp131x081x rp131x151x rp131x331x rp131x501x 0 100 800 600 200 400 900 700 300 500 1000 output current i out (ma) esr ( ) v in =1.6v to 6.0v c1=ceramic 2.2 f, c2=ceramic 2.2 f 0.01 100 10 1 0.1 topt= - 40 c topt=85 c 0 100 800 600 200 400 900 700 300 500 1000 output current i out (ma) esr ( ) v in =1.6v to 6.0v c1=ceramic 2.2 f, c2=ceramic 2.2 f 0.01 100 10 1 0.1 topt= - 40 c topt=85 c 0 100 800 600 200 400 900 700 300 500 1000 output current i out (ma) esr ( ) v in =3.3v to 6.0v c1=ceramic 2.2 f, c2=ceramic 2.2 f 0.01 100 10 1 0.1 topt= - 40 c topt=85 c 0 100 800 600 200 400 900 700 300 500 1000 output current i out (ma) esr ( ) v in =5.0v to 6.0v c1=ceramic 2.2 f, c2=ceramic 4.7 f 0.01 100 10 1 0.1 topt= - 40 c topt=85 c rp131x no.ea-174-160426 21 measurement board pattern ic mount area (unit: mm) 40 package information power dissipation (dfn1616-6b) this specification is at mounted on board. power dissipation (p d ) depends on conditions of mounting on board. this specification is based on the measurement at the condition below: * measurement conditions standard test land pattern environment mounting on board (wind velocity=0m/s) board material glass cloth epoxy plastic (double-sided) board dimensions 40mm*40mm*1.6mm copper ratio top side: approx. 50%, back side: approx. 50% through-holes ja = (125-25oc)/0.64w= 156oc/w jc 23oc/w the above graph shows the power dissipation of t he package based on tjmax=125oc and tjmax=150oc. operating the ic in the shaded area in the graph might have an influence it's lifetim e. operating time must be within the time limit described in the table below, in case of operating in the shaded area. operating time estimated years (operating four hours/day) 13,000 hours 9years power dissipation 0 100 200 300 400 500 600 700 800 900 1000 0 25 50 75 100 125 150 power dissipation p d (mw) ambient temperature (c) 85 800 640 rp131x no.ea-174-160426 22 package dimensions (dfn1616-6b) mark specifications (dfn1616-6b) c d e f : product code ? refer to rp131l series mark specification table. g h : lot number ? alphanumeric serial number index 1.60 1.60 a b 0.05 x4 0.5 0.70 0.05 1.30 1 3 46 0.05 m ab 0.20 0.05 s s 0.4max. 0.25 0.05 (3x0.15) (unit : mm) bottom view ) tab is gnd level. (they are connected to the reverse side of this ic.) the tab is better to be connected to the gnd, but leaving it open is also acceptable. 0.1 0.05 rp131x no.ea-174-160426 23 rp131l series mark specification table pkg: dfn1616-6b rp131lxx1b rp131lxx1d part numbe r c d e f vset part numbe r c d e f vset rp131l081b c b 0 1 0.8v rp131l081d c c 0 1 0.8v rp131l091b c b 0 2 0.9v rp131l091d c c 0 2 0.9v rp131l101b c b 0 3 1.0v rp131l101d c c 0 3 1.0v rp131l111b c b 0 4 1.1v rp131l111d c c 0 4 1.1v rp131l121b c b 0 5 1.2v rp131l121d c c 0 5 1.2v rp131l121b5 c b 0 6 1.25v rp131l121d5 c c 0 6 1.25v rp131l131b c b 0 7 1.3v rp131l131d c c 0 7 1.3v rp131l141b c b 0 8 1.4v rp131l141d c c 0 8 1.4v rp131l151b c b 0 9 1.5v rp131l151d c c 0 9 1.5v rp131l161b c b 1 0 1.6v rp131l161d c c 1 0 1.6v rp131l171b c b 1 1 1.7v rp131l171d c c 1 1 1.7v rp131l181b c b 1 2 1.8v rp131l181d c c 1 2 1.8v rp131l181b5 c b 1 3 1.85v rp131l181d5 c c 1 3 1.85v rp131l191b c b 1 4 1.9v rp131l191d c c 1 4 1.9v rp131l201b c b 1 5 2.0v rp131l201d c c 1 5 2.0v rp131l211b c b 1 6 2.1v rp131l211d c c 1 6 2.1v rp131l221b c b 1 7 2.2v rp131l221d c c 1 7 2.2v rp131l231b c b 1 8 2.3v rp131l231d c c 1 8 2.3v rp131l241b c b 1 9 2.4v rp131l241d c c 1 9 2.4v rp131l251b c b 2 0 2.5v rp131l251d c c 2 0 2.5v rp131l261b c b 2 1 2.6v rp131l261d c c 2 1 2.6v rp131l271b c b 2 2 2.7v rp131l271d c c 2 2 2.7v rp131l281b c b 2 3 2.8v rp131l281d c c 2 3 2.8v rp131l281b5 c b 2 4 2.85v rp131l281d5 c c 2 4 2.85v rp131l291b c b 2 5 2.9v rp131l291d c c 2 5 2.9v rp131l301b c b 2 6 3.0v rp131l301d c c 2 6 3.0v rp131l311b c b 2 7 3.1v rp131l311d c c 2 7 3.1v rp131l321b c b 2 8 3.2v rp131l321d c c 2 8 3.2v rp131l331b c b 2 9 3.3v rp131l331d c c 2 9 3.3v rp131l341b c b 3 0 3.4v rp131l341d c c 3 0 3.4v rp131l351b c b 3 1 3.5v rp131l351d c c 3 1 3.5v rp131l361b c b 3 2 3.6v rp131l361d c c 3 2 3.6v rp131l371b c b 3 3 3.7v rp131l371d c c 3 3 3.7v rp131l381b c b 3 4 3.8v rp131l381d c c 3 4 3.8v rp131l391b c b 3 5 3.9v rp131l391d c c 3 5 3.9v rp131l401b c b 3 6 4.0v rp131l401d c c 3 6 4.0v rp131l411b c b 3 7 4.1v rp131l411d c c 3 7 4.1v rp131l421b c b 3 8 4.2v rp131l421d c c 3 8 4.2v rp131l431b c b 3 9 4.3v rp131l431d c c 3 9 4.3v rp131l441b c b 4 0 4.4v rp131l441d c c 4 0 4.4v rp131l451b c b 4 1 4.5v rp131l451d c c 4 1 4.5v rp131l461b c b 4 2 4.6v rp131l461d c c 4 2 4.6v rp131l471b c b 4 3 4.7v rp131l471d c c 4 3 4.7v rp131l481b c b 4 4 4.8v rp131l481d c c 4 4 4.8v rp131l491b c b 4 5 4.9v rp131l491d c c 4 5 4.9v rp131l501b c b 4 6 5.0v rp131l501d c c 4 6 5.0v rp131l101b5 c b 4 7 1.05v rp131l101d5 c c 4 7 1.05v rp131l511b c b 4 8 5.1v rp131l511d c c 4 8 5.1v rp131l521b c b 4 9 5.2v rp131l521d c c 4 9 5.2v rp131l531b c b 5 0 5.3v rp131l531d c c 5 0 5.3v rp131l541b c b 5 1 5.4v rp131l541d c c 5 1 5.4v rp131l551b c b 5 2 5.5v rp131l551d c c 5 2 5.5v rp131x no.ea-174-160426 24 power dissipation (dfn(plp)1820-6) this specification is at mount ed on board. power dissipation (p d ) depends on conditions of mounting on board. this specification is based on the measurement at the condition below: measurement conditions standard land pattern environment mounting on board (wind velocity=0m/s) board material glass cloth epoxy plastic (double-sided) board dimensions 40mm * 40mm * 1.6mm copper ratio top side: approx. 50%, back side: approx. 50% through-hole 0.54mm * 30pcs measurement result (ta=25 c) standard land pattern power dissipation 880mw(tjmax=125 c) 1100mw(tjmax=150 c) thermal resistance ja=(125 - 25 c)/0.88w=114 c/w - the above graph shows the power dissi pation of the package based on tjmax=125 c and tjmax=150 c. operating the ic in the shaded area in the graph might have an influence it's lifetime. operating time must be within the time limit described in t he table below, in case of operating in the shaded area. operating time estimated years (operating four hours/day) 13,000 hours 9years 40 40 measurement board pattern ic mount area unit: mm 0 200 400 600 800 1000 1200 0 25 50 75 100 125 150 a mbient tem p erature ( c ) power dissi p ation p d ( mw ) 85 880 1100 40 40 rp131x no.ea-174-160426 25 package dimensions (dfn(plp)1820-6) mark specifications (dfn(plp)1820-6) c d e f : product code ?refer to rp131k series mark specification table. g h : lot number ? alphanumeric serial number 2.00 1.80 0.25 0.1 0.25 0.1 0.1nom. 0.3 0.1 0.5 0.6max. a b 0.05 x4 0.05 m ab index s 0.05min 1 2 3 4 5 6 1.6 0.1 1.0 0.1 0.20 0.1 * 0.05 s (unit: mm) bottom view * ) tab is gnd level. (they are connected to the reverse side of this ic.) the tab is better to be connected to the gnd, but leaving it open is also acceptable. c d e f g h 1 2 3 6 5 4 rp131x no.ea-174-160426 26 rp131k series mark specification table pkg: dfn(plp)1820-6 rp131kxx1b rp131kxx1d part number c d e f vset part number c d e f vset rp131k081b a m 0 1 0.8v rp131k081d a n 0 1 0.8v rp131k091b a m 0 2 0.9v rp131k091d a n 0 2 0.9v rp131k101b a m 0 3 1.0v rp131k101d a n 0 3 1.0v rp131k111b a m 0 4 1.1v rp131k111d a n 0 4 1.1v rp131k121b a m 0 5 1.2v rp131k121d a n 0 5 1.2v rp131k121b5 a m 0 6 1.25v rp131k121d5 a n 0 6 1.25v rp131k131b a m 0 7 1.3v rp131k131d a n 0 7 1.3v rp131k141b a m 0 8 1.4v rp131k141d a n 0 8 1.4v rp131k151b a m 0 9 1.5v rp131k151d a n 0 9 1.5v rp131k161b a m 1 0 1.6v rp131k161d a n 1 0 1.6v rp131k171b a m 1 1 1.7v rp131k171d a n 1 1 1.7v rp131k181b a m 1 2 1.8v rp131k181d a n 1 2 1.8v rp131k181b5 a m 1 3 1.85v rp131k181d5 a n 1 3 1.85v rp131k191b a m 1 4 1.9v rp131k191d a n 1 4 1.9v rp131k201b a m 1 5 2.0v rp131k201d a n 1 5 2.0v rp131k211b a m 1 6 2.1v rp131k211d a n 1 6 2.1v rp131k221b a m 1 7 2.2v rp131k221d a n 1 7 2.2v rp131k231b a m 1 8 2.3v rp131k231d a n 1 8 2.3v rp131k241b a m 1 9 2.4v rp131k241d a n 1 9 2.4v rp131k251b a m 2 0 2.5v rp131k251d a n 2 0 2.5v rp131k261b a m 2 1 2.6v rp131k261d a n 2 1 2.6v rp131k271b a m 2 2 2.7v rp131k271d a n 2 2 2.7v rp131k281b a m 2 3 2.8v rp131k281d a n 2 3 2.8v rp131k281b5 a m 2 4 2.85v rp131k281d5 a n 2 4 2.85v rp131k291b a m 2 5 2.9v rp131k291d a n 2 5 2.9v rp131k301b a m 2 6 3.0v rp131k301d a n 2 6 3.0v rp131k311b a m 2 7 3.1v rp131k311d a n 2 7 3.1v rp131k321b a m 2 8 3.2v rp131k321d a n 2 8 3.2v rp131k331b a m 2 9 3.3v rp131k331d a n 2 9 3.3v rp131k341b a m 3 0 3.4v rp131k341d a n 3 0 3.4v rp131k351b a m 3 1 3.5v rp131k351d a n 3 1 3.5v rp131k361b a m 3 2 3.6v rp131k361d a n 3 2 3.6v rp131k371b a m 3 3 3.7v rp131k371d a n 3 3 3.7v rp131k381b a m 3 4 3.8v rp131k381d a n 3 4 3.8v rp131k391b a m 3 5 3.9v rp131k391d a n 3 5 3.9v rp131k401b a m 3 6 4.0v rp131k401d a n 3 6 4.0v rp131k411b a m 3 7 4.1v rp131k411d a n 3 7 4.1v rp131k421b a m 3 8 4.2v rp131k421d a n 3 8 4.2v rp131k431b a m 3 9 4.3v rp131k431d a n 3 9 4.3v rp131k441b a m 4 0 4.4v rp131k441d a n 4 0 4.4v rp131k451b a m 4 1 4.5v rp131k451d a n 4 1 4.5v rp131k461b a m 4 2 4.6v rp131k461d a n 4 2 4.6v rp131k471b a m 4 3 4.7v rp131k471d a n 4 3 4.7v rp131k481b a m 4 4 4.8v rp131k481d a n 4 4 4.8v rp131k491b a m 4 5 4.9v rp131k491d a n 4 5 4.9v rp131k501b a m 4 6 5.0v rp131k501d a n 4 6 5.0v rp131k101b5 a m 4 7 1.05v rp131k101d5 a n 4 7 1.05v rp131k551b a m 4 8 5.5v rp131k551d a n 4 8 5.5v rp131k511b a m 4 9 5.1v rp131k511d a n 4 9 5.1v rp131k521b a m 5 0 5.2v rp131k521d a n 5 0 5.2v rp131k531b a m 5 1 5.3v rp131k531d a n 5 1 5.3v rp131k541b a m 5 2 5.4v rp131k541d a n 5 2 5.4v rp131x no.ea-174-160426 27 power dissipation p d (mw) 1500 1400 1300 1200 1100 1000 900 800 700 600 500 400 300 200 100 0 0 25 50 75 100 125 150 ambient temperature ( c) 85 on board (standard land pattern) on board ( hi g h watta g e land pattern ) free air power dissipation (sot-89-5) this specification is at mounted on board. power dissipation (p d ) depends on conditions of mounting on board. this specification is based on the measurement at the condition below: measurement conditions high wattage land pattern standard land pattern environment mounting on board (wind velocity=0m/s) mounting on board (wind velocity=0m/s) board material glass cloth epoxy plastic (doubl e-sided) glass cloth epoxy plastic (double-sided) board dimensions 30mm ? 30mm ? 1.6mm 50mm * 50mm ? 1.6mm copper ratio top side: approx. 20% back side: approx. 100% top side: approx. 10% back side: approx. 100% through-hole 0.85mm ? 10pcs - measurement result (ta=25 c) high wattage land pattern standard land pattern free air power dissipation 1300mw 900mw (tjmax=125 c) 1125mw (tjmax=150 c) 500mw thermal resistance 77 c/w 111 c/w 200 c/w measurement board pattern ic mount area unit: mm 30 7.5 15 30 7.5 50 50 high wattage standard 15 - the above graph shows the power dissipation of the package based on tjmax=125 c and tjmax=150 c. operating the ic in the shaded area in the graph might have an influence it's lifetime. operating time must be within the time limit described in the table below, in case of operating in the shaded area. operating time estimated years (operating four hours/day) 4,500 hours 3years 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 0 25 50 75 100 125 150 a mbient temperature (c) power dissipation p d (mw) 85 900 1125 on board power dissipation rp131x no.ea-174-160426 28 package dimensions (sot-89-5) 1.50.1 1.50.1 0.470.1 0.420.1 0.420.1 1.50.1 0.40.1 0.40.1 0.1 s s 0.30.2 0.30.2 4 5 3 2 1 bottom view 0.420.1 4.50.1 1.60.2 4.350.1 2.50.1 0.40.3 5 4 1 2 3 1.0 1.000.2 unit : mm mark specifications (sot-89-5) c d e f : product code ?refer to rp131h series mark specification table. g h : lot number ? alphanumeric serial number c d e f g h rp131x no.ea-174-160426 29 rp131h series mark specification table pkg: sot-89-5 rp131hxx1b rp131hxx1d part number c d e f vset part number c d e f vset rp131h081b u 0 8 b 0.8v rp131h081d u 0 8 d 0.8v rp131h091b u 0 9 b 0.9v rp131h091d u 0 9 d 0.9v rp131h101b u 1 0 b 1.0v rp131h101d u 1 0 d 1.0v rp131h111b u 1 1 b 1.1v rp131h111d u 1 1 d 1.1v rp131h121b u 1 2 b 1.2v rp131h121d u 1 2 d 1.2v rp131h131b u 1 3 b 1.3v rp131h131d u 1 3 d 1.3v rp131h141b u 1 4 b 1.4v rp131h141d u 1 4 d 1.4v rp131h151b u 1 5 b 1.5v rp131h151d u 1 5 d 1.5v rp131h161b u 1 6 b 1.6v rp131h161d u 1 6 d 1.6v rp131h171b u 1 7 b 1.7v rp131h171d u 1 7 d 1.7v rp131h181b u 1 8 b 1.8v rp131h181d u 1 8 d 1.8v rp131h191b u 1 9 b 1.9v rp131h191d u 1 9 d 1.9v rp131h201b u 2 0 b 2.0v rp131h201d u 2 0 d 2.0v rp131h211b u 2 1 b 2.1v rp131h211d u 2 1 d 2.1v rp131h221b u 2 2 b 2.2v rp131h221d u 2 2 d 2.2v rp131h231b u 2 3 b 2.3v rp131h231d u 2 3 d 2.3v rp131h241b u 2 4 b 2.4v rp131h241d u 2 4 d 2.4v rp131h251b u 2 5 b 2.5v rp131h251d u 2 5 d 2.5v rp131h261b u 2 6 b 2.6v rp131h261d u 2 6 d 2.6v rp131h271b u 2 7 b 2.7v rp131h271d u 2 7 d 2.7v rp131h281b u 2 8 b 2.8v rp131h281d u 2 8 d 2.8v rp131h291b u 2 9 b 2.9v rp131h291d u 2 9 d 2.9v rp131h301b u 3 0 b 3.0v rp131h301d u 3 0 d 3.0v rp131h311b u 3 1 b 3.1v rp131h311d u 3 1 d 3.1v rp131h321b u 3 2 b 3.2v rp131h321d u 3 2 d 3.2v rp131h331b u 3 3 b 3.3v rp131h331d u 3 3 d 3.3v rp131h341b u 3 4 b 3.4v rp131h341d u 3 4 d 3.4v rp131h351b u 3 5 b 3.5v rp131h351d u 3 5 d 3.5v rp131h361b u 3 6 b 3.6v rp131h361d u 3 6 d 3.6v rp131h371b u 3 7 b 3.7v rp131h371d u 3 7 d 3.7v rp131h381b u 3 8 b 3.8v rp131h381d u 3 8 d 3.8v rp131h391b u 3 9 b 3.9v rp131h391d u 3 9 d 3.9v rp131h401b u 4 0 b 4.0v rp131h401d u 4 0 d 4.0v rp131h411b u 4 1 b 4.1v rp131h411d u 4 1 d 4.1v rp131h421b u 4 2 b 4.2v rp131h421d u 4 2 d 4.2v rp131h431b u 4 3 b 4.3v rp131h431d u 4 3 d 4.3v rp131h441b u 4 4 b 4.4v rp131h441d u 4 4 d 4.4v rp131h451b u 4 5 b 4.5v rp131h451d u 4 5 d 4.5v rp131h461b u 4 6 b 4.6v rp131h461d u 4 6 d 4.6v rp131h471b u 4 7 b 4.7v rp131h471d u 4 7 d 4.7v rp131h481b u 4 8 b 4.8v rp131h481d u 4 8 d 4.8v rp131h491b u 4 9 b 4.9v rp131h491d u 4 9 d 4.9v rp131h501b u 5 0 b 5.0v rp131h501d u 5 0 d 5.0v rp131h511b u 5 1 b 5.1v rp131h511d u 5 1 d 5.1v rp131h521b u 5 2 b 5.2v rp131h521d u 5 2 d 5.2v rp131h531b u 5 3 b 5.3v rp131h531d u 5 3 d 5.3v rp131h541b u 5 4 b 5.4v rp131h541d u 5 4 d 5.4v rp131h551b u 5 5 b 5.5v rp131h551d u 5 5 d 5.5v rp131h121b5 u 0 1 b 1.25v rp131h121d5 u 0 1 d 1.25v rp131h181b5 u 0 2 b 1.85v rp131h181d5 u 0 2 d 1.85v rp131h281b5 u 0 3 b 2.85v rp131h281d5 u 0 3 d 2.85v rp131h101b5 u 0 4 b 1.05v rp131h101d5 u 0 4 d 1.05v rp131x no.ea-174-160426 30 power dissipation (hsop-6j) this specification is at mounted on board. power dissipation (p d ) depends on conditions of mounting on board. this specification is based on the measurement at the condition below: measurement conditions high wattage land pattern standard land pattern environment mounting on board (wind velocity=0m/s) mounting on board (wind velocity=0m/s) board material glass cloth epoxy plastic (doubl e-sided) glass cloth epoxy plastic (double-sided) board dimensions 50mm * 50mm * 1.6mm 50mm * 50mm * 1.6mm copper ratio 90% 50% through-hole 0.5mm * 44pcs 0.5mm * 44pcs measurement result (ta=25 c) high wattage land pattern standard land pattern free air power dissipation 2000mw 1700mw (tjmax=125 c) 2125mw (tjmax=150 c) 540mw thermal resistance 50 c/w 59 c/w 185 c/w high wattage standard measurement board pattern ic mount area unit: mm 49 10 18 50 50 40 20 20 power dissipation p d ( w) 2600 2400 2200 2000 1800 1600 1400 1200 1000 80 0 600 400 200 0 0 25 50 75 100 125 150 ambient temperature ( c) 85 1700 540 on board (high wattage land pattern) on board (standard land pattern) free air - the above graph shows the power dissipation of the package based on tjmax=125 c and tjmax=150 c. operating the ic in the shaded area in the graph might have an influence it's lifetime. operating time must be within the time limit described in the table below, in case of operating in the shaded area. operating time 1,500 hours 0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 0 25 50 75 100 125 150 a mbient temperature (c) power dissipation p d (mw) 85 1700 2125 on board power dissipation rp131x no.ea-174-160426 31 package dimensions (hsop-6j) 3.81 123 5.020.3 654 (unit: mm) 0.10 0.12 m 0.605typ. 0.150.1 1.50.1 1.670.1 0.40.1 0.600.2 0.2 6.00.3 3.90.2 + 0.10 - 0.05 mark specifications (hsop-6j) c d e f : product code ?refer to rp131s series mark specification table. g h : lot number ? alphanumeric serial number f g h c d e rp131x no.ea-174-160426 32 rp131s series mark specification table pkg: hsop-6j rp131sxx1b rp131sxx1d part number c d e f vset part number c d e f vset rp131s081b g 0 8 b 0.8v rp131s081d g 0 8 d 0.8v rp131s091b g 0 9 b 0.9v rp131s091d g 0 9 d 0.9v rp131s101b g 1 0 b 1.0v rp131s101d g 1 0 d 1.0v rp131s111b g 1 1 b 1.1v rp131s111d g 1 1 d 1.1v rp131s121b g 1 2 b 1.2v rp131s121d g 1 2 d 1.2v rp131s131b g 1 3 b 1.3v rp131s131d g 1 3 d 1.3v rp131s141b g 1 4 b 1.4v rp131s141d g 1 4 d 1.4v rp131s151b g 1 5 b 1.5v rp131s151d g 1 5 d 1.5v rp131s161b g 1 6 b 1.6v rp131s161d g 1 6 d 1.6v rp131s171b g 1 7 b 1.7v rp131s171d g 1 7 d 1.7v rp131s181b g 1 8 b 1.8v rp131s181d g 1 8 d 1.8v rp131s191b g 1 9 b 1.9v rp131s191d g 1 9 d 1.9v rp131s201b g 2 0 b 2.0v rp131s201d g 2 0 d 2.0v rp131s211b g 2 1 b 2.1v rp131s211d g 2 1 d 2.1v rp131s221b g 2 2 b 2.2v rp131s221d g 2 2 d 2.2v rp131s231b g 2 3 b 2.3v rp131s231d g 2 3 d 2.3v rp131s241b g 2 4 b 2.4v rp131s241d g 2 4 d 2.4v rp131s251b g 2 5 b 2.5v rp131s251d g 2 5 d 2.5v rp131s261b g 2 6 b 2.6v rp131s261d g 2 6 d 2.6v rp131s271b g 2 7 b 2.7v rp131s271d g 2 7 d 2.7v rp131s281b g 2 8 b 2.8v rp131s281d g 2 8 d 2.8v rp131s291b g 2 9 b 2.9v rp131s291d g 2 9 d 2.9v rp131s301b g 3 0 b 3.0v rp131s301d g 3 0 d 3.0v rp131s311b g 3 1 b 3.1v rp131s311d g 3 1 d 3.1v rp131s321b g 3 2 b 3.2v rp131s321d g 3 2 d 3.2v rp131s331b g 3 3 b 3.3v rp131s331d g 3 3 d 3.3v rp131s341b g 3 4 b 3.4v rp131s341d g 3 4 d 3.4v rp131s351b g 3 5 b 3.5v rp131s351d g 3 5 d 3.5v rp131s361b g 3 6 b 3.6v rp131s361d g 3 6 d 3.6v rp131s371b g 3 7 b 3.7v rp131s371d g 3 7 d 3.7v rp131s381b g 3 8 b 3.8v rp131s381d g 3 8 d 3.8v rp131s391b g 3 9 b 3.9v rp131s391d g 3 9 d 3.9v rp131s401b g 4 0 b 4.0v rp131s401d g 4 0 d 4.0v rp131s411b g 4 1 b 4.1v rp131s411d g 4 1 d 4.1v rp131s421b g 4 2 b 4.2v rp131s421d g 4 2 d 4.2v rp131s431b g 4 3 b 4.3v rp131s431d g 4 3 d 4.3v rp131s441b g 4 4 b 4.4v rp131s441d g 4 4 d 4.4v rp131s451b g 4 5 b 4.5v rp131s451d g 4 5 d 4.5v rp131s461b g 4 6 b 4.6v rp131s461d g 4 6 d 4.6v rp131s471b g 4 7 b 4.7v rp131s471d g 4 7 d 4.7v rp131s481b g 4 8 b 4.8v rp131s481d g 4 8 d 4.8v rp131s491b g 4 9 b 4.9v rp131s491d g 4 9 d 4.9v rp131s501b g 5 0 b 5.0v rp131s501d g 5 0 d 5.0v rp131s511b g 5 1 b 5.1v rp131s511d g 5 1 d 5.1v rp131s521b g 5 2 b 5.2v rp131s521d g 5 2 d 5.2v rp131s531b g 5 3 b 5.3v rp131s531d g 5 3 d 5.3v rp131s541b g 5 4 b 5.4v rp131s541d g 5 4 d 5.4v rp131s551b g 5 5 b 5.5v rp131s551d g 5 5 d 5.5v rp131s121b5 g 0 1 b 1.25v rp131s121d5 g 0 1 d 1.25v rp131s181b5 g 0 2 b 1.85v rp131s181d5 g 0 2 d 1.85v rp131s281b5 g 0 3 b 2.85v rp131s281d5 g 0 3 d 2.85v rp131s101b5 g 0 4 b 1.05v rp131s101d5 g 0 4 d 1.05v rp131x no.ea-174-160426 33 power dissipation (to-252-5-p2) this specification is at mount ed on board. power dissipation (p d ) depends on conditions of mounting on board. this specification is based on the measurement at the condition below: measurement conditions land pattern a land pattern b environment mounting on board (wind velocity 0m/s) mounting on board (wind velocity 0m/s) board material glass cloth epoxy plastic (double-layers) glass cloth epoxy plastic (four-layers) board dimensions 50mm * 50mm * 1.6mm 76.2mm * 114.3mm * 0.8 mm copper ratio top side: approx. 50%, back side: approx. 50% top, back side: approx. 96%, 2nd, 3rd: 100% through - hole c) land pattern a land pattern b power dissipation 1900mw (tjmax=125 c) 2375mw (tjmax=150 c) 3800mw (tjmax=125 c) 4750mw (tjmax=150 c) thermal resistance ja=(125-25 c)/1.9w= 53 c/w c)/3.8w = 26 c/w jc= 17 c/w jc= 7 c/w 0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 0 2 5 50 7 5 1 00 12 5 1 50 a mbient temperature (c) power dissipation p d (mw) 85 1900 2375 land pattern a 0 400 800 1200 1600 2000 2400 2800 3200 3600 4000 4400 4800 5200 0 25 50 75 100 125 150 ambient temperature (c) power dissipation pd (mw) 85 3800 4750 land pattern b 50 50 board a measurent board pattern ic mount area unit : mm 76.2 40 114.3 50 50 board b measurent board pattern ic mount area unit : mm - the above graph shows t he power dissipation of the package based on tjmax=125 c and tjmax=150 c. operating the ic in the shaded area in the graph might have an influence it's lifetime. operating time must be within the time limit described in the table below, in case of operating in the shaded area. operating time estimated years (operating four hours/day) 13,000 hours 9years power dissipation rp131x no.ea-174-160426 34 package dimensions (to-252-5-p2) (unit: mm) 0.50 0.10 0.50 0.10 (0 8 ) 1.52 + 0.26 - 0.13 (0 0.127) s 0.12 m 0.50 0.10 2.30 0.20 (1.00) 0.10 (6.20) 6.60 0.20 5.34 0.20 6.10 0.20 (1.00) 9.90 0.30 1.10 0.20 c0.60 1.27 2.70 0.20 (4.06) (3.56) r0.325 r0.225 (4.19) (1.50) (5.04) 15 mark specifications (to-252-5-p2) c d e f g h i j : refer to rp131j series mark specification table. k l : lot number ? alphanumeric serial number ????? ? rp131x no.ea-174-160426 35 rp131j series mark specification table pkg: to-252-5 rp131jxx1b rp131jxx1d part number c d e f g h i j vset part number c d e f g h i j vset rp131j081b d 1 j 0 8 1 b 0.8v rp131j081d d 1 j 0 8 1 d 0.8v rp131j091b d 1 j 0 9 1 b 0.9v rp131j091d d 1 j 0 9 1 d 0.9v rp131j101b d 1 j 1 0 1 b 1.0v rp131j101d d 1 j 1 0 1 d 1.0v rp131j111b d 1 j 1 1 1 b 1.1v rp131j111d d 1 j 1 1 1 d 1.1v rp131j121b d 1 j 1 2 1 b 1.2v rp131j121d d 1 j 1 2 1 d 1.2v rp131j131b d 1 j 1 3 1 b 1.3v rp131j131d d 1 j 1 3 1 d 1.3v rp131j141b d 1 j 1 4 1 b 1.4v rp131j141d d 1 j 1 4 1 d 1.4v rp131j151b d 1 j 1 5 1 b 1.5v rp131j151d d 1 j 1 5 1 d 1.5v rp131j161b d 1 j 1 6 1 b 1.6v rp131j161d d 1 j 1 6 1 d 1.6v rp131j171b d 1 j 1 7 1 b 1.7v rp131j171d d 1 j 1 7 1 d 1.7v rp131j181b d 1 j 1 8 1 b 1.8v rp131j181d d 1 j 1 8 1 d 1.8v rp131j191b d 1 j 1 9 1 b 1.9v rp131j191d d 1 j 1 9 1 d 1.9v rp131j201b d 1 j 2 0 1 b 2.0v rp131j201d d 1 j 2 0 1 d 2.0v rp131j211b d 1 j 2 1 1 b 2.1v rp131j211d d 1 j 2 1 1 d 2.1v rp131j221b d 1 j 2 2 1 b 2.2v rp131j221d d 1 j 2 2 1 d 2.2v rp131j231b d 1 j 2 3 1 b 2.3v rp131j231d d 1 j 2 3 1 d 2.3v rp131j241b d 1 j 2 4 1 b 2.4v rp131j241d d 1 j 2 4 1 d 2.4v rp131j251b d 1 j 2 5 1 b 2.5v rp131j251d d 1 j 2 5 1 d 2.5v rp131j261b d 1 j 2 6 1 b 2.6v rp131j261d d 1 j 2 6 1 d 2.6v rp131j271b d 1 j 2 7 1 b 2.7v rp131j271d d 1 j 2 7 1 d 2.7v rp131j281b d 1 j 2 8 1 b 2.8v rp131j281d d 1 j 2 8 1 d 2.8v rp131j291b d 1 j 2 9 1 b 2.9v rp131j291d d 1 j 2 9 1 d 2.9v rp131j301b d 1 j 3 0 1 b 3.0v rp131j301d d 1 j 3 0 1 d 3.0v rp131j311b d 1 j 3 1 1 b 3.1v rp131j311d d 1 j 3 1 1 d 3.1v rp131j321b d 1 j 3 2 1 b 3.2v rp131j321d d 1 j 3 2 1 d 3.2v rp131j331b d 1 j 3 3 1 b 3.3v rp131j331d d 1 j 3 3 1 d 3.3v rp131j341b d 1 j 3 4 1 b 3.4v rp131j341d d 1 j 3 4 1 d 3.4v rp131j351b d 1 j 3 5 1 b 3.5v rp131j351d d 1 j 3 5 1 d 3.5v rp131j361b d 1 j 3 6 1 b 3.6v rp131j361d d 1 j 3 6 1 d 3.6v rp131j371b d 1 j 3 7 1 b 3.7v rp131j371d d 1 j 3 7 1 d 3.7v rp131j381b d 1 j 3 8 1 b 3.8v rp131j381d d 1 j 3 8 1 d 3.8v rp131j391b d 1 j 3 9 1 b 3.9v rp131j391d d 1 j 3 9 1 d 3.9v rp131j401b d 1 j 4 0 1 b 4.0v rp131j401d d 1 j 4 0 1 d 4.0v rp131j411b d 1 j 4 1 1 b 4.1v rp131j411d d 1 j 4 1 1 d 4.1v rp131j421b d 1 j 4 2 1 b 4.2v rp131j421d d 1 j 4 2 1 d 4.2v rp131j431b d 1 j 4 3 1 b 4.3v rp131j431d d 1 j 4 3 1 d 4.3v rp131j441b d 1 j 4 4 1 b 4.4v rp131j441d d 1 j 4 4 1 d 4.4v rp131j451b d 1 j 4 5 1 b 4.5v rp131j451d d 1 j 4 5 1 d 4.5v rp131j461b d 1 j 4 6 1 b 4.6v rp131j461d d 1 j 4 6 1 d 4.6v rp131j471b d 1 j 4 7 1 b 4.7v rp131j471d d 1 j 4 7 1 d 4.7v rp131j481b d 1 j 4 8 1 b 4.8v rp131j481d d 1 j 4 8 1 d 4.8v rp131j491b d 1 j 4 9 1 b 4.9v rp131j491d d 1 j 4 9 1 d 4.9v rp131j501b d 1 j 5 0 1 b 5.0v rp131j501d d 1 j 5 0 1 d 5.0v rp131j511b d 1 j 5 1 1 b 5.1v rp131j511d d 1 j 5 1 1 d 5.1v rp131j521b d 1 j 5 2 1 b 5.2v rp131j521d d 1 j 5 2 1 d 5.2v rp131j531b d 1 j 5 3 1 b 5.3v rp131j531d d 1 j 5 3 1 d 5.3v rp131j541b d 1 j 5 4 1 b 5.4v rp131j541d d 1 j 5 4 1 d 5.4v rp131j551b d 1 j 5 5 1 b 5.5v rp131j551d d 1 j 5 5 1 d 5.5v rp131j121b5 d 1 j 1 2 1 b 5 1.25v rp131j121d5 d 1 j 1 2 1 d 5 1.25v rp131j181b5 d 1 j 1 8 1 b 5 1.85v rp131j181d5 d 1 j 1 8 1 d 5 1.85v rp131j281b5 d 1 j 2 8 1 b 5 2.85v rp131j281d5 d 1 j 2 8 1 d 5 2.85v rp131j101b5 d 1 j 1 0 1 b 5 1.05v rp131j101b5 d 1 j 1 0 1 d 5 1.05v http://www.e-devices.ricoh.co.jp/en/ 4 b m f t 4 v q q p s u 0$? d f t 3 * $ 0 ) & |