pma-series ? p8au-xxxxelf ? single output ? sip4 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 1/3 p8au-xxxxelf all specifications typical at ta=25c, nominal inpu t voltage and full load unless otherwise specified input specifications voltage range 10% input filter capacitors input reflected ripple current1 20 ma pk-pk output specifications voltage accuracy 3% short circuit protection short term line regulation 1.2% / 1% vin change load regulation (20% - 100%) 10% (3.3vout models: 20%) ripple and noise (20mhz bandwidth) 100 mv pk-pk temperature coefficient 0.02% / c general specifications efficiency see table i/o isolation voltage (3 sec.) 1000 vdc i/o isolation capacity 60 pf, typ. i/o isolation resistance 1000 mohm switching frequency 80 khz (variable) humidity 95% rel h reliability calculated mtbf (mil-hdbk-217f) > 1.121 mhrs physical specifications case material non conductive black plastic (ul94v-0 rated) potting material epoxy (ul94v-0 rated) weight ~ 1.5g, typ. environment specifications operating temperature -40 to +85c (ambient) maximum case temperature 100c storage temperature -40 to +125c cooling free air convection rohs conform soldering 260c, max. (1.5mm from case 10s.) mainzer stra?e 151?153 d-55299 nackenheim tel. +49 6135 7026-0 fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de the pm a series p8au - xxxxelf is a family of cost effective 1.5 w single output dc/dc converters. these converters are in an ultra miniature sip4 case. devices are encapsulated. high performance fe atures: 1000vdc input/output isolation, high efficiency operation, output voltage accuracy of 3% maximum, input range of 10% tolerance and low output ripple and noise. pma-series 1.5 watt unregulated single output sip4 case 1 kv dc i/o isolation low ripple and noise rev.11-2008
pma-series ? p8au-xxxxelf ? single output ? sip4 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 2/3 selection guide single output order # i n p u t v o l t a g e ( v d c ) i n p u t c u r r e n t n o l o a d ( m a ) i n p u t c u r r e n t f u l l l o a d ( m a ) o u t p u t v o l t a g e ( v d c ) o u t p u t c u r r e n t f u l l l o a d ( m a ) e f f i c i e n c y ( % ) c a p a c i t o r l o a d ( u f ) 2 single output p8au-053r3elf 5 30 361 3.3 400 73 220 p8au-0505elf 5 30 400 5 300 75 220 p8au-057r2elf 5 30 400 7.2 208 75 220 p8au-0509elf 5 30 400 9 167 75 220 p8au-0512elf 5 30 384 12 125 78 220 p8au-0515elf 5 30 384 15 100 78 220 p8au-0518elf 5 30 384 18 83 78 220 p8au-0524elf 5 30 379 24 62.5 79 220 p8au-123r3elf 12 15 148 3.3 400 74 220 P8AU-1205ELF 12 15 168 5 300 74 220 p8au-127r2elf 12 15 166 7.2 208 75 220 p8au-1209elf 12 15 166 9 167 75 220 p8au-1212elf 12 15 166 12 125 75 220 p8au-1215elf 12 15 162 15 100 77 220 p8au-1218elf 12 15 162 18 83 77 220 p8au-1224elf 12 15 162 24 62.5 77 220 p8au-243r3elf 24 10 73 3.3 400 75 220 p8au-2405elf 24 10 83 5 300 75 220 p8au-247r2elf 24 10 83 7.2 208 75 220 p8au-2409elf 24 10 83 9 167 75 220 p8au-2412elf 24 10 82 12 125 76 220 p8au-2415elf 24 10 82 15 100 76 220 p8au-2418elf 24 10 82 18 83 76 220 p8au-2424elf 24 10 79 24 62.5 79 220 p8au-483r3elf 48 6 36 3.3 400 75 220 p8au-4805elf 48 6 41 5 300 76 220 p8au-487r2elf 48 6 41 7.2 208 76 220 p8au-4809elf 48 6 41 9 167 76 220 p8au-4812elf 48 6 40 12 125 77 220 p8au-4815elf 48 6 40 15 100 77 220 p8au-4818elf 48 6 40 18 83 77 220 p8au-4824elf 48 6 40 24 62.5 78 220 if you need other specifications, please enquire.
pma-series ? p8au-xxxxelf ? single output ? sip4 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 3/3 package / pinning / derating modelcode datecode 1 2 3 4 11.68 (0.46) 9.65 (0.38) 3.05 (0.12) 2.54 (0.10) bottom view 1 2 3 4 1.25 (0.05) 0.50 (0.02) 6.00* (0.24)* 0.50 (0.02) 0.50 (0.02) 0.50 (0.02) 0.25 (0.01) all dimensions are typical in millimeters (inches). - pin diameter: 0.5 +/-0.05 (0.02 +/-0.002) - pin pitch tolerance: +/-0.35 (+/-0.014) - case tolerance +/-0.5 (+/-0.02) specification may change without notice. * the thickness of 48vin voltage is 7.50 (0.29) pe a k sip4 C plastic case # single 1 - vin 2 +vin 3 - vout 4 +vout pin connections app notes: 1 = measured input reflected ripple current with a simu lated source inductance of 12uh. 2 = tested by minimal vin and constant resistive load. - operation under no-load conditions will not damag e these devices, but they will not observe the list ed specifications.
|