www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 1 of 9 s pec n o : ? ? s s p p e e c c i i f f i i c c a a t t i i o o n n customer product ? saw filter model no hdf 433.92a1 smd - 6 m arking ? hdf6 531 prepared checked approved ? d a t e 201 1 - 3 - 22 ??? shoulder electronics limited ?? c ustomer received: c hecked ? approved d ate
saw filter hdf 433.92a1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 2 of 9 ?? history record date spec . no . ?? part no . ??? customer no . modify content ? remark
saw filter hdf 433.92a1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 3 of 9 1. package dimension marking hdf 6 531 hd: brand f : filter 6 : smd - 6 531 : no .
saw filter hdf 433.92a1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 4 of 9 2. maximum rating operation temperature range - 40 to + 8 5 storage temperature range - 40 to +85 rf power 20dbm 3.1 electronic characteristics u nit minimum typical maximum center frequency mhz - 433.92 - insertion loss ( 433.00~434.71 mhz) db 2.5 3.2 amplitude ripple ( 433.00~434.71 mhz) db 0.8 2.0 vswr ( 433.00~434.71 mhz) 1.5 relative attenuation dc ~ 380 mhz 380 ~ 413.5 mhz 413.5 ~ 424 mhz 443.75 ~ 470 mhz 470 ~ 650 mhz 650 ~ 1000 mhz db 55 45 40 35 43 40 65 52 43 38 48 50 - input/output impedance ohms 50 3.2 frequency characteristics
saw filter hdf 433.92a1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 5 of 9 4. test circuit 5 . environmental characteristics 5 - 1 high temperature exposure subject the device to +85 for 16 hours. then release the filter into the room conditions for 24 hours prior to the measurement. it shall fulfill the specifications in 3.1 . 5 - 2 low temperature exposure subject the device to - 40 for 16 hours. then release the device into the ro om conditions for 24 hours prio r to the measurement. it shall fulfill the specifications in 3.1 . 5 - 3 temperature cycling subject the device to a low temperature of - 40 for 30 minutes. following by a high temperature of +8 5 for 30 minutes. then release the device into the room conditions for 24 hours prior to the me a surement. it shall meet the specifications in 3.1 . 5 - 4 resistance to solder heat dip the device terminals no closer than 1.5mm into the solder bath at 260 10 for
saw filter hdf 433.92a1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 6 of 9 10 1 sec. then release the device into the room conditions for 4 hours. the device shall meet the specifications in 3.1 . 5 - 5 solderability subject the device terminals into the solder bath at 245 5 for 5s, more than 95% area of the terminals must be covered with new sold er. it shall meet the specifications in 3.1 . 5 - 6 mechanical shock drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in 3.1 . 5 - 7 vibration subject the device to the vibration fo r 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. the device shall f ulfill the specifications in 3.1 . 6 . remark 6 .1 static voltage static voltage between signal load & ground may cause deterioration &destruction of the co mponent. please avoid static voltage. 6 .2 ultrasonic cleaning ultrasonic vibration may cause deteri oration & destruction of the component. please avoid ultrasonic cleaning 6 .3 soldering only lea ds of component may be soldered . please avoid sold ering another part of component. 7 . packing 7 .1 dimensions (1) carrier tape: figure 1 (2) reel: figure 2 (3) the product shall be packed properly not to be damaged during transportation and storage. 7 .2 reeling quantity 1000 pcs/reel 7?? 3000 pcs/reel 13?? 7 .3 taping structure (1) the tape shall be wound around the reel in the direction shown below.
saw filter hdf 433.92a1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 7 of 9 (2) label device name user product name quantity lot no. (3) leader part and vacant position specifications. 8 . tape specifications 8 .1 tensile strength of carrier tape: 4.4n/mm width 8 .2 top cover tape adhesion (see the below figure) (1) pull off angle: 0~15 o (2) speed: 300mm/min. (3) force: 20~70g
saw filter hdf 433.92a1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 8 of 9 [figure 1] carrier tape dimensions [unit:mm] w f e p0 p1 p2 d0 d1 t1 t2 a b 12.00 0.30 5.50 0.10 1.75 0.10 4.00 0.10 4.00 0.10 2.00 0.10 ?1.50 ? 1.5 0.25 0.31 0.05 1.30 0.10 3.4 max. 3.4 max [figure 2] [unit:mm] a b c d e w t r
saw filter hdf 433.92a1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 9 of 9 ? 330 1.0 ? 100 0.5 ? 13 0.5 ? 21 0.8 2 0.5 13 0.3 3 max. 1.0 max.
|
