part number 856541 201 mhz saw filter data sheet subject to change or obsolescence without notice rev d 08 / 10 ? triquint semiconductor page 1 of 6 features for gsm and edge applications usable bandwidth 0.22 mhz typical 1db bandwidth of 0.34 mhz low loss high attenuation balanced operation at 200 or single - ended operation at 50 (different matching required) ceramic surface mount package (smp) h ermetic rohs compliant (2002/95/ec), pb - free package pin configuration surface mount 13.30 x 6.50 x 1.50 mm bottom view smp - 53 c balanced configuration pin no. description 10,1 input 5,6 output 2,3, 4 case ground 7,8,9 ca se ground dimensions shown are nominal in millimeters all tolerances are 0.15mm except overall length and width 0.10mm body: al 2 o 3 ceramic lid: kovar , ni plated terminations: au plating 0.5 - 1.0 m, over a 2 C 6 m ni plating pb 6 7 8 9 10 5 4 3 2 1 1.80 6.50 1.02 1.91 13.3 2.31 r0.51 1.50 nom. 1.65 max. 0.64
part number 856541 201 mhz saw filter data sheet subject to change or obsolescence without notice rev d 08 / 10 ? triquint semiconductor page 2 of 6 electrical specifications (1) operating temperature range: (2) 0 to +70 c parameter (3) minimum typical ( 4 ) maximum unit center frequency (f c ) - 201 - mhz insertion loss - 6.1 7 .0 db lower 1 d b band edge upper 1 db band edge - 201.11 200.83 201.17 200.89 - mhz mhz amplitude variation (5) 200.89 C 201.11 mhz - 0.6 1 .0 db p - p absolute group delay at f c 2.05 2.3 2.55 s group delay variation 200.89 C 201.1 1 mhz - 0.8 1.5 s stopband attenuation (6 ) fc 0.3 mhz to fc 0.4 mhz fc 0.4 mhz to fc 0.6 mhz fc 0.6 mhz to fc 0.8 mhz fc 0.8 mhz to fc 1.5 mhz fc 1.5 mhz to fc 35 mhz 16 27 28 36 38 25 29 32 40 40 - - - - - db db db db db s ource impedance ( balanced ) (7 ) load impedance ( balanced ) ( 7 ) - - 200 200 - - ? ? notes : 1. all specifications are based on the triquint test circuit shown below 2. in production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over temperature 3. electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances 4. typical values are based on average measurements at room temperature 5. amplitude variation is defined as the difference between the lowest loss and the highe st loss within defined frequency points 6. relative to insertion loss at 201 mhz 7. this is the optimum impedance in order to achieve the performance shown test circuit: actual matching values may vary due to pcb layout and parasitics 20 0 balanced input 20 0 balanced output 2,3,4 7,8,9 200 15pf 33nh 10 6 200 27nh 33nh 1 27nh 5 18pf
part number 856541 201 mhz saw filter data sheet subject to change or obsolescence without notice rev d 08 / 10 ? triquint semiconductor page 3 of 6 electrical specifications (1) operating temperature range: (2) - 40 to +85 c parameter (3) minimum typical ( 4 ) maximum unit center frequency (f c ) - 201 - mhz insertion loss - 6.1 7.2 db lower 1 d b ban d edge upper 1 db band edge - 201.081 200.83 201.17 200.89 - mhz mhz amplitude variation (5) 200.89 C 201.11 mhz - 0.6 1.4 db p - p absolute group delay at f c 2.05 2.3 2.55 s group delay variation 200.89 C 201.11 mhz - 0.8 1.5 s stopband attenuation (6 ) fc - 35 mhz to fc - 1.5 mhz fc - 1.5 mhz to fc - 0.8 mhz fc - 0.8 mhz to fc - 0.6 mhz fc - 0.6 mhz to fc - 0.4 mhz fc - 0.4 mhz to fc - 0.3 mhz fc + 0.3 mhz to fc + 0.4 mhz fc + 0.4 mhz to fc + 0.6 mhz fc + 0.6 mhz to fc + 0.8 mhz fc + 0.8 mhz to fc + 1.5 mhz fc + 1.5 mhz to fc + 35 mhz 38 35 28 25 10.5 16 27 28 35 38 40 40 32 29 25 25 29 32 40 40 - - - - - - - - - - db db db db db db db db db db source impedance (balanced) (7) load impedance (balanced) (7) - - 200 200 - - ? ? notes : 1. all specifications are based on the triquint test circuit shown below 2. in production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over temperature 3. electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances 4. typical values are based on average measurements at room temperature 5. amplitude variation is defined as the difference between the lowest loss and the highe st loss within defined frequency points 6. relative to insertion loss at 201 mhz 7. this is the optimum impedance in order to achieve the performance shown test circuit: actual matching values may vary due to pcb layout and parasitics 200 balanced input 200 balanced output 2,3,4 7,8,9 200 15pf 33nh 10 6 200 27nh 33nh 1 27nh 5 18pf
part number 856541 201 mhz saw filter data sheet subject to change or obsolescence without notice rev d 08 / 10 ? triquint semiconductor page 4 of 6 typical performance (at room temperature )
part number 856541 201 mhz saw filter data sheet subject to change or obsolescence without notice rev d 08 / 10 ? triquint semiconductor page 5 of 6 matching schematics actual matching values may vary due to pcb layout and parasitics 20 0 balanced input 20 0 balanced output marking pcb footprint the date code consists of: day of the current year (julian, 3 digits), last digit of the year (1 digit) and hour (2 digits) this footprint represents a recommendation only dimensions shown are nominal in millimeters tape and reel dimensions shown are nominal in millimeters packaging quantity: 2 000 units/reel 2,3,4 7,8,9 200 15pf 33nh 10 6 200 27nh 33nh 1 27nh 5 18pf id dot date code xxxxxx 856541 sawtek 2.51 6.70 8.86 .69 1.22 2.00 direction of travel ? 330 24.8 2.7 ?102 ? 13.0 ? 20.2 2.0 id dot a a 24 1.75 11.5 ? 1.5 2.3 13.9 4.0 ? 1.5 2.0 0.3 12.0 7.1 section a-a
part number 856541 201 mhz saw filter data sheet subject to change or obsolescence without notice rev d 08 / 10 ? triquint semiconductor page 6 of 6 maximum ratings parameter symbol minimum maximum unit operating temperature range t - 40 +85 o c storage temperature range t stg - 40 +85 o c important notes warnings electrostatic sensitiv e device (esd) avoid ultrasonic exposure rohs compliance this product complies with eu directive 2002/95/ec (rohs) solderability c ompatible with jesd22 - b102, pb - free process, 260c peak reflow temperature ( see soldering profile ) links to additional technical information pcb layout tips qualification flowchart soldering profile s - parameters rohs information other technical information triquints liability is limited only to the surface acoustic wave (saw) component(s) described in this data sheet. triquint does not accept any liability for applications, processes, circuits or assemblies, which are implemented using any triquint component described in this dat a sheet. contact information phone: +1 (407) 886 - 8860 f ax: +1 (407) 886 - 7061 email: info - product@tqs.com web: www.triquint.com or contact one of our worldwide network of sale s offices, representatives or distributors po box 609501 orlando, fl 32860 - 9501 usa pb
|
