View EVAL-ADT7X20EBZ_8898069.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

0.25c accurate, 16 - bit digital i 2 c temperature sensor data sheet adt7420 rev. 0 document feedback information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062 - 9106, u.s.a. tel: 781.329.4700 ? 2012 analog devices, inc. a ll rights reserved. technical support www.analog.com features high p erformance te mperature accuracy 0.20c from ?10c to +85c at 3.0 v 0. 25c from ? 20c to +10 5c from 2.7 v to 3.3 v 16- bit resolution: 0.0078c ultra low temperature drift: 0.0073c nist traceable or equivalent fast first temperature conve rsion on power - up of 6 ms easy i mplementation no temperature calibration/correction required by user no linearity correction required low p ower power - saving 1 sample per second (sps) mode 700 w typical at 3.3 v in normal mode 7 w typical at 3.3 v in s hutdown mode wide operating r ange s t emperature r ange : ?40c to +150c v oltage r ange : 2.7 v to 5.5 v programmable i nterrupts cr itical overtemperature inte r rupt overtemperature/undertemperature interrupt i 2 c - compatible interface 16- lead , 4 mm 4 mm lfcsp rohs - compliant package applications rtd and t hermistor r eplacement thermocouple c old junction compensation medical e quipment industrial c ontrol and t est food t ransportation and s torage environmental m onitoring and hvac laser diode temperature control general description the adt7420 is a high accuracy digital temperature sensor offering breakthrough performance over a wid e industrial range, housed in a 4 mm 4 mm lfcsp package. it contains an internal band gap reference, a temperature sensor, and a 16 - bit adc to monitor and digi tize the temperature to 0.0078 c resolution. the adc resolution, by default, is set to 13 bits (0.0625c). the adc resolution is a user programmable mode that can be changed through the serial interface. the adt7420 is guaranteed to operate over supply voltages from 2. 7 v to 5.5 v. operating at 3.3 v, the average supply current is t ypi - cally 210 a. the adt7420 has a shutdown mode that powers down the device and offers a shutdown current of typically 2 .0 a at 3.3 v. the adt7420 is rated for ope ration over the ?40 c to +150c temperature range. pin a0 and pin a1 are available for address selection, giving the adt7420 four possible i 2 c addresses. the ct pin is an open - drain output that becomes active when the temperature exceeds a programmable critical tem perature limit. the int pin is also an open - drain output that becomes active when the tempera - ture exceeds a programmable limit. the int pin and ct pin can operate in comparator and interrupt event mo des. product h ighlights 1. ease of use, no calibration or correction required by the user. 2. low po wer consumption . 3. e xcellent long - term stability and reliability. 4. high accuracy for industrial, instrumentation , and medical applications . 5. packaged in a 16 - lead , 4 mm 4 mm lfcsp rohs - compliant package . functional block dia gram internal reference pointer register status register 12 11 temperature value register configuration register t hyst register t low register t high register t crit register software reset register id register temperature sensor t high t crit t low internal oscillator filter logic - modulator v dd gnd 10 9 ct int 3 4 a0 a1 1 2 scl sda i 2 c interface adt7420 09013-001 figure 1.
adt7420 data sheet rev. 0 | page 2 of 24 table of contents features .............................................................................................. 1 applications ....................................................................................... 1 general description ......................................................................... 1 product highlights ........................................................................... 1 func tional block diagram .............................................................. 1 revision history ............................................................................... 2 specifications ..................................................................................... 3 i 2 c t iming specifications ............................................................ 5 absolute maximum ratings ............................................................ 6 esd caution .................................................................................. 6 pin configuration and function descriptions ............................. 7 typical performance characteristics ............................................. 8 theory of operation ...................................................................... 10 circuit information .................................................................... 10 converter details ........................................................................ 10 normal mode .............................................................................. 10 one - shot mode .......................................................................... 10 1 sps mode .................................................................................. 11 shutdown ..................................................................................... 11 fault queue ................................................................................. 11 temperature data format ......................................................... 12 temperature conversion formulas ......................................... 12 registers ........................................................................................... 13 address pointer register ........................................................... 13 temperature value registers .................................................... 13 status register ............................................................................. 14 configuration register .............................................................. 14 t high setpoint registers ............................................................. 15 t low setpoint registers .............................................................. 15 t crit setpoint registers .............................................................. 15 t hyst setpoint register ............................................................... 16 id register ................................................................................... 16 serial interface ................................................................................ 17 serial bus address ...................................................................... 17 writing data ............................................................................... 18 reading data ............................................................................... 19 reset ............................................................................................. 20 general call ................................................................................ 20 int and ct outputs ...................................................................... 21 undertemperature and overtemperature detection ............ 21 applications information .............................................................. 23 thermal response time ........................................................... 23 supply decouplin g ..................................................................... 23 powering from a switching regulator ..................................... 23 temperature measurement ....................................................... 23 quick guide to measuring temperature ................................ 23 outline dimensions ....................................................................... 24 ordering guide .......................................................................... 24 revisio n history 12/ 12 rev ision 0: initial version
data sheet adt7420 rev. 0 | page 3 of 24 specifications t a = ?40c to +1 25 c, v dd = 2.7 v to 5.5 v, unless otherwise noted. table 1 . parameter min typ max unit test conditions/comments temperature sensor and adc accuracy 1 0.0 0 17 0.20 2 c t a = ?10c to +85c, v dd = 3.0 v 0.25 c t a = ?20c to +105c, v dd = 2.7 v to 3.3 v 0.31 c t a = ?40c to +105 c, v dd = 3.0 v 0.35 c t a = ?40c to +10 5c, v dd = 2.7 v to 3.3 v 0.50 c t a = ?40c to +125c, v dd = 2.7 v to 3.3 v 0.50 3 c t a = ?10c to +105c, v dd = 4.5 v to 5.5 v 0.66 c t a = ?40c to +125c, v dd = 4.5 v to 5.5 v ?0.85 c t a = +150c, v dd = 4.5 v to 5.5 v ?1.0 c t a = +150c, v dd = 2.7 v to 3.3 v adc resolution 13 bits twos complement temperature value of the sign bit plus 12 adc bits (power - up default resolution) 16 bits twos complement temperature value of the sign bit plus 15 adc bits (bit 7 = 1 in the configuration register) temperature resolution 13- bit 0.0625 c 13- bit resolution (sign + 12 - bit) 16- bit 0.0078 c 16- bit resolution (sign + 15 - bit) temperature conversion time 240 ms continuous conversion and one - shot conversion modes fast temperature conversion time 6 ms first conversion on power - up only 1 sps conversion time 60 ms conversion time for 1 sps mode t emperature hysteresis 4 0.002 c temperature cycle = 25c to 125c and back to 25c repeatability 5 0.015 c t a = 25c drift 6 0.0073 c 500 hour stress test at +150c with v dd = 5.0 v dc psrr 0.1 c/v t a = 25c digital outputs ( ct, int, sda op en drain) high output leakage current, i oh 0.1 5 a ct and int pins pulled up to 5.5 v output low voltage, v ol 0.4 v i ol = 3 ma at 5.5 v, i ol = 1 ma at 3.3 v output high voltage, v oh 0.7 v dd v output capacitance, c out 2 pf digital in puts (scl, sda, a0, a1 ) input current 1 a v in = 0 v to v dd input low voltage, v il 0.3 v dd v scl and sda only 0.4 v a0 and a1 only input high voltage, v ih 0.7 v dd v scl and sda only 2 v a0 and a1 only scl, sda glitch rejection 50 ns input filtering suppresses noise spikes of less than 50 ns pin capacitance 2 10 pf power requirements supply voltage 2.7 5.5 v supply current at 3.3 v 210 265 a peak current while converting, i 2 c interface inactive at 5.5 v 250 300 a peak current while converting, i 2 c interface inactive 1 sps current at 3.3 v 46 a v dd = 3.3 v, 1 sps mode, t a = 25c at 5.5 v 65 a v dd = 5.5 v, 1 sps mode, t a = 25c
adt7420 data sheet rev. 0 | page 4 of 24 parameter min typ max unit test conditions/comments shutdown current at 3.3 v 2.0 15 a supply current in shutd own mode at 5.5 v 5.2 25 a supply current in shutdown mode power dissipation normal mode 700 w v dd = 3.3 v, normal mode at 25c power dissipation 1 sps 150 w power dissipated for v dd = 3.3 v, t a = 25c 1 accuracy spec ification includes repeatability. 2 the equivalent 3 limits are 0.15 c . this 3 specification is provided to enable comparison with other vendors who use these limits. 3 for higher accuracy at 5 v operation, contact analog devices , inc . 4 temperature hysteresis does not include repeatability. 5 based on a floating average of 10 readings. 6 drift includes s older h eat r esistance and life time test performed as per jedec standard jesd22 - a108 .
data sheet adt7420 rev. 0 | page 5 of 24 i 2 c timing specifications t a = ?40c to +150c, v dd = 2.7 v to 5.5 v, unless otherwise noted. all input signals are specified with rise time (t r ) = fall time (t f ) = 5 ns (10% to 90% of v dd ) and timed from a voltage level of 1.6 v. table 2. parameter min typ max unit test conditions/comments serial interface 1 see figure 2 scl frequency 0 400 khz scl high pulse width, t high 0.6 s scl low pulse width, t low 1.3 s scl, sda rise time, t r 0.3 s scl, sda fall time, t f 0.3 s hold time (start condition), t hd:sta 0.6 s after this period, the first clock is generated setup time (start condition), t su:sta 0.6 s relevant for repeated start condition data setup time, t su:dat 0.02 s setup time (stop condition), t su:sto 0.6 s data hold time, t hd:dat (master) 0.03 s bus-free time (between stop and start condition), t buf 1.3 s capacitive load for each bus line, c b 400 pf 1 sample tested during initial release to ensure compliance. timing diagram p s t low t r t f t hd:sta t hd:dat t su:dat t su:sta t hd:sta t su:sto t high scl ps sda t buf 09013-002 figure 2. serial interface timing diagram
adt7420 data sheet rev. 0 | page 6 of 24 absolute maximum rat ings table 3 . parameter rating v dd to gnd ? 0.3 v to +7 v sda voltage to gnd ? 0.3 v to v dd + 0.3 v scl output voltage to gnd ?0.3 v to v dd + 0.3 v a0 input voltage to gnd ?0.3 v to v dd + 0.3 v a1 input voltage to gnd ?0.3 v to v dd + 0.3 v ct and int output voltage to gnd ?0.3 v to v dd + 0.3 v esd rating (human body model ) 2.0 kv operating temperature range 1 ? 40 c to +150c storage temperature range ?65c to +160c maximum junction temperature, t jmax 150c 16- lead lfcsp ( cp -16-17) power dissipation 2 w max = (t jmax ? t a 3 )/ ja thermal imped ance 4 ja , junction - to - ambient (still air) 3 7 c/w jc , junction -to - case 33 c/w ir reflow soldering 220c peak temperature (rohs - compliant package) 260c ( + 0c / ? 5 c ) time at peak temperature 20 sec to 40 sec ramp - up rate 3c/sec maximum ramp - down ra te ?6c/sec maximum time from 25c to peak temperature 8 minutes maximum 1 sustained operation above 125c result s in a shorter product lifetime. for more information , contact analog devices . 2 values relate to package being used on a standard 2 - layer pcb. this gives a worst - case ja and jc . 3 t a = ambient temperature. 4 junction - to - case resistance is applicable to components featuring a preferential flow direction, for example, components mounted on a heat sink. junction - to - ambient is more useful for air - cooled, pcb - mounted components. stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those indic ated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. esd caution
data sheet adt7420 rev. 0 | page 7 of 24 pin configuration and fu nction descriptions 12 17 ep 11 10 1 3 4 v dd gnd ct 9 int scl a0 2 sda a1 6 n c 5 n c 7 n c 8 n c 1 6 n c 1 5 n c 1 4 n c 1 3 n c top view (not to scale) notes 1. nc = no conne c t. the nc pin is not bonded to the die internally. 2 . to ensure correct operation, the exposed pad should either be left floating or connected to ground. 09013-004 adt7420 figure 3. pin configuration table 4. pin function descriptions pin no. mnemonic description 1 scl i 2 c serial clock input. the serial clock is used to clock in and clock out data to and from any register of the adt7420 . open-drain configuration. a pull-up resistor is required, typically 10 k. 2 sda i 2 c serial data input/outp ut. serial data to and from the part is provid ed on this pin. open-drain configuration. a pull-up resistor is required, typically 10 k. 3 a0 i 2 c serial bus address selection pin. logic input. connect to gnd or v dd to set an i 2 c address. 4 a1 i 2 c serial bus address selection pin. logic input. connect to gnd or v dd to set an i 2 c address. 5 nc no connect. the nc pin is not bonded to the die internally. 6 nc no connect. the nc pin is not bonded to the die internally. 7 nc no connect. the nc pin is not bonded to the die internally. 8 nc no connect. the nc pin is not bonded to the die internally. 9 int overtemperature and undertemperature indicator. logic o utput. power-up default setting is as an active low comparator interrupt. open-drain configuration. a pull-up resistor is required, typically 10 k. 10 ct critical overtemperature indicator. logic output. power-up de fault polarity is active low. open-drain configuration. a pull-up resistor is required, typically 10 k. 11 gnd analog and digital ground. 12 v dd positive supply voltage (2.7 v to 5.5 v). the supply should be decoupled with a 0.1 f ceramic capacitor to ground. 13 nc no connect. the nc pin is not bonded to the die internally. 14 nc no connect. the nc pin is not bonded to the die internally. 15 nc no connect. the nc pin is not bonded to the die internally. 16 nc no connect. the nc pin is not bonded to the die internally. 17 ep exposed pad. to ensure correct operation, the exposed pad should either be left floating or connected to ground.
adt7420 data sheet rev. 0 | page 8 of 24 typical performance characteristics temper a ture error (c) ?40 ?60 ?20 0 20 40 temper a ture (c) 60 80 100 120 140 ?1.00 ?0.50 0 0.50 0.25 ?0.25 0.75 ?0.75 1.00 max accurac y limits max accurac y limits 09013-027 figure 4 . temperature accuracy at 3 v temper a ture error (c) ?40 ?60 ?20 0 20 40 temper a ture (c) 60 80 100 120 140 ?1.00 ?0.50 0 0.50 0.25 ?0.25 0.75 ?0.75 1.00 max accurac y limits max accurac y limits 09013-026 figure 5. temperature accuracy at 5 v ?100 ?50 0 50 100 150 200 i dd ( a) temper a ture (c) 3.0v 1sps 5.5v 1sps 5.5v continuous conversion 3.0v continuous conversion 09013-028 0 50 100 150 200 250 300 figure 6 . operating supply current vs. temperature 3.6v shutdown i dd ( a) temper a ture (c) 0 5 10 15 20 25 30 ?100 ?50 0 50 100 150 200 3.3v 3.0v 2.7v 4.5v 5.0v 5.5v 09013-032 figure 7 . shutdown current vs. temperature 0 50 100 150 200 250 300 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 i dd ( a) supp l y vo lt age (v) i dd continuous conversion i dd 1sps 09013-029 figure 8 . average operating supply current vs. supply voltage 09013-210 0 1 2 3 4 5 6 7 8 2 . 5 3 . 0 3 . 5 4 . 0 4 . 5 5 . 0 5 . 5 6 . 0 s hu t d o w n i d d ( a ) s u pp l y vo l t a g e (v) figure 9 . shutd own current vs. supply voltage
data sheet adt7420 rev. 0 | page 9 of 24 0 20 40 60 80 100 120 140 0 5 10 15 25 20 dut temper a ture ( c) time (s) 125c 105c 85c 09013- 1 10 it takes less than 2 seconds to reach 63.2% of its temperature span figure 10 . thermal response time
adt7420 data sheet rev. 0 | page 10 of 24 theory of operation circuit information the adt7420 is a high accuracy digital temperature sensor that uses a 16-bit adc to monitor and digitize the temperature to 0.0078c of resolution. the adc resolution, by default, is set to 13 bits (0.0625c). an internal temperature sensor generates a voltage proportional to absolute temperature, which is com- pared to an internal voltage reference and input into a precision digital modulator. the internal temperature sensor has high accuracy and linearity over the entire rated temperature range without needing correc- tion or calibration by the user. the sensor output is digitized by a sigma-delta (-) modulator, also known as the charge balance type analog-to-digital conver- ter. this type of converter utilizes time-domain oversampling and a high accuracy comparator to deliver 16 bits of resolution in an extremely compact circuit. converter details the - modulator consists of an input sampler, a summing network, an integrator, a comparator, and a 1-bit dac. this architecture creates a negative feedback loop and minimizes the integrator output by changing the duty cycle of the comparator output in response to input voltage changes. the comparator samples the output of the integrator at a much higher rate than the input sampling frequency. this oversampling spreads the quantization noise over a much wider band than that of the input signal, improving overall noise performance and increasing accuracy. - ? modulator integrator comparator temperature value register clock generator lpf digital filter 1-bit dac voltage ref and vptat 1-bit 13-bit/ 16-bit 09013-012 figure 11. - modulator the adt7420 can be configured to operate in any one of the following four operating modes: normal, one-shot, 1 sps, and shutdown. normal mode in normal mode (default power-up mode) the adt7420 runs an automatic conversion sequence. during this automatic con- version sequence, a conversion typically takes 240 ms to complete and the adt7420 is continuously converting. this means that as soon as one temperature conversion is completed, another temperature conversion begins. each temperature conversion result is stored in the temperature value registers and is available through the i 2 c interface. in continuous conversion mode, the read operation provides the most recent converted result. on power-up, the first conversion is a fast conversion, taking typically 6 ms. if the temperature exceeds 147c, the ct pin asserts low. if the temperature exceeds 64c, the int pin asserts low. fast conversion temperature accuracy is typically within 5c. the conversion clock for the part is generated internally. no external clock is required except when reading from and writing to the serial port. the measured temperature value is compared with a critical temperature limit (stored in the 16-bit t crit setpoint read/write register), a high temperature limit (stored in the 16-bit t high set- point read/write register), and a low temperature limit (stored in the 16-bit t low setpoint read/write register). if the measured value exceeds these limits, the int pin is activated; and if it exceeds the t crit limit, the ct pin is activated. the int and ct pins are programmable for polarity via the configuration register, and the int and ct pins are also programmable for interrupt mode via the configuration register. one-shot mode setting bit 6 to 0 and bit 5 to 1 of the configuration register (register address 0x03) enables the one-shot mode. when this mode is enabled, the adt7420 immediately completes a conversion and then goes into shutdown mode. wait for a minimum of 240 ms after writing to the operation mode bits before reading back the temperature from the tem- perature value register. this time ensures that the adt7420 has time to power up and complete a conversion. to obtain an updated temperature conversion, reset bit 6 to 0 and bit 5 to 1 in the configuration register (0x03). the one-shot mode is useful when one of the circuit design priorities is to reduce power consumption.
data sheet adt7420 rev. 0 | page 11 of 24 ct and int operation in one - shot mode see figure 12 for more information on one - shot ct pin operation for t crit overte mperature events when one of the limits is exceeded. note that in interrupt mode, a read from any register resets the int and ct pins. for the int pin in the comparator mode, if the temperature drops below the t high C t hyst value or goes above the t low + t hyst value, a write to the operation mode bits (bit 5 and bit 6 of the con figuration register, register address 0x03) resets the int pin. for the ct pin in the comparator mode, if the temperature drops below the t crit C t hyst value, a write to the operati on mode bits (bit 6 = 0 and bit 5 = 1 of the configuration register, register address 0x03) resets the ct pin (see figure 12 ). note that when using one - shot mode, ensure that the refresh rate is appropriate to th e application being used. 1 sps mode in this mode, the part perfor ms one measurement per second. a conversion takes only 60 ms typically , and it remains in the idle state for the remaining 940 ms period. th is mode is enabled by writing 1 to bit 6 and 0 to bit 5 of the configuration re gister ( register address 0x03) . shutdown the adt7420 can be placed in shutdown mode by writing 1 to bit 6 and 1 to bit 5 of the configuration register (register address 0x03), i n which case the entire ic is shut down and no further conversions are initiated until the adt7420 is taken out of shutdown mode. the adt7420 can be taken out of shu tdown mode by writing 0 to bit 6 and 0 to bit 5 in the configuration register (register address 0x03). the adt7420 typically takes 1 ms (with a 0.1 f decoupling capacitor) to come out of shutdown mode. the conversion result from the last conversion prior to shutdown can still be read from the adt7420 even when it is in shutdown mode. when the part is taken out of shutdown mode, the internal clock is started and a conversion is initiated. fault queue bit 0 and bit 1 of the configuration register (register address 0x03) are used to set up a fault q ueue. the queue can facilitate up to four fault events to prevent false tripping of the int and ct pins when the adt7420 is used in a noisy temperature environment. the number of faults set in the queue must occur consecutively to set the int and ct outputs. for example, if the number of faults set in the queue is four, t hen four consecutive temperature conversi ons must occur with each result exceeding a tempera ture limit in any of the limit registe rs before the int and ct pins are activated. if two consecu tive temperature conversions exceed a temperature limit and the th ird conversion does not, the fault count is reset back to zero. temper a ture 149c 148c 147c 146c 145c 144c 143c 142c 141c 140c ct pin polarit y = active low ct pin polarit y = active high t crit t crit ? t hyst time *there is a 240ms del a y between writing t o the configur a tion register t o s t art a s t andard one-shot conversion and the ct pin going active. this is due t o the conversion time. the del a y is 60ms in the case of a one-shot conversion. write t o bit 5 and bit 6 of configur a tion register. * write t o bit 5 and bit 6 of configur a tion register. * write t o bit 5 and bit 6 of configur a tion register. * 09013-013 figure 12 . one - shot ct pin
adt7420 data sheet rev. 0 | page 12 of 24 temperature data for mat one lsb of the adc corresponds to 0.0625c in 13 - bit mode or 0.0078c in 16 - bit mode . the adc can theoretical ly measure a temperature range of 255c, but the adt7420 is guaranteed to measure a low value temperature limit of ? 40 c to a high value temperature limit of +150c. the temperature m easurement result is store d in the 16 - bit temperature value register and is compared with the high temperature limits stored in the t crit setpoint register and the t high setpoint register. it is also com - pared with the low temperature limit stored in the t low setpoint register. te m perature data in the temperature value register, the t crit setpoint register, the t high setpoint register, and the t low setpoint register are represented by a 13 - bit twos complement word. the msb is the temperature sign bit. the three lsbs, bit 0 to bit 2, on power - up , are not part of the temperature conver sion result and are flag bits for t crit , t high , and t low . table 5 shows the 13 - bit temperature data format without bit 0 to bit 2. the number of bits in the tem perature data - word can be ext ended to 16 bits, twos complement, by setting bit 7 to 1 in the confi - guration register (register address 0x03). when using a 16 - bit temperature data value, bit 0 to bit 2 are not used as flag bits and are , instead, the lsb bit s of the temperature value. the power - on default setting ha s a 13 - bit temperature data value. readin g back the temperature from the temperature value register requires a 2 - byte read. designers that use a 9 - bit temperature data format can still use the adt7 420 by ignoring the last four lsbs of the 13 - bit temperature value. these four lsbs are bit 6 to bit 3 in table 5 . table 5 . 13 - bit temperature data format temperature digital output (binary) bits [15 :3 ] digital output (hex) ?4 0 c 1 1101 100 0 0000 0x1d 8 0 ?25 c 1 1110 0111 0000 0x1e70 ?0.0625 c 1 1111 1111 1111 0x1fff 0 c 0 0000 0000 0000 0x000 +0.0625 c 0 0000 0000 0001 0x001 +25 c 0 0001 1001 0000 0x190 +105 c 0 0110 1001 0000 0x690 +1 25c 0 0111 1101 0000 0x7d0 +150 c 0 1001 0110 0000 0x960 temperature conversi on formulas 16- bit temperature data format positive temperature = adc code (dec)/128 negative temperature = ( adc code (dec) C 65,536)/128 where adc code uses all 16 bits of t he data byte, including the sign bit. negative temperature = ( adc code (dec) C 32,768)/128 w here bit 15 (sign bit) is removed from the adc code. 13- bit temperature data format positive temperature = adc code (dec)/16 negative temperature = ( adc code (dec) ? 8192)/16 where adc code uses the first 13 msbs of the data byte, including the sign bit. negative temperature = ( adc code (dec) C 4096)/16 where bit 15 (sign bit) is removed from the adc code. 10- bit temperature data format positive temperature = adc cod e (dec)/2 negative temperature = ( adc code (dec) ? 1024)/2 where adc code uses all 10 bits of the data byte, including the sign bit. negative temperature = ( adc code (dec) ? 512)/2 where bit 9 (sign bit) is removed from the adc code. 9 - bit temperature data format positive temperature = adc code (dec) negative temperature = adc code (dec) ? 512 where adc code uses all nine bits of the data byte, including the sign bit. negative temperature = adc code (dec) ? 256 where bit 8 (sign bit) is removed from the adc code.
data sheet adt7420 rev. 0 | page 13 of 24 registers the adt7420 contains 14 registers: ? nine temperature registers ? a status register ? an id register ? a configuration register ? an address pointer register ? a software reset all registers are eight bits wide. the temperature value registers, the status register, and the id register are read - only. the software reset is a write - only register. on power - up, the address poin ter register is loaded with 0x00 and points to the temperature value most signific ant byte register (register address 0x00) . table 6 . adt7420 registers register address description power - on default 0x00 temperature value most significant byte 0x00 0x01 temperatu re value least significant byte 0x00 0x02 status 0x00 0x03 configuration 0x00 0x04 t high setpoint most significant byte 0x20 (64c) 0x05 t high setpoint least significant byte 0x00 (64c) 0x06 t low setpoint most significant byte 0 x 05 (10c) 0x07 t low setpoint least significant byte 0x00 (10c) 0x08 t crit setpoint most significant byte 0x49 (147c) 0x09 t crit setpoint least significant byte 0x80 (147c) 0x0a t hyst setpoint 0x05 (5c) 0x0b id 0xc b 0x2f software reset 0xxx address pointer regi ster this register is always the first register written to during a write to the adt7420 . it should be set to the address of the register to which the write or read transaction is intended. table 7 shows the register address of each register on the adt7420 . the default value of the address pointer register is 0x00. table 7 . address pointer register p7 p6 p5 p4 p3 p2 p1 p0 add7 add6 add5 add4 add3 add2 add1 add0 temperature value re gisters the temperature value consist s of two bytes, one m ost s ignifi- cant b yte and one l east s ignificant b yte. these values can be read in two separate 1 - byte reads or in a single 2 - byte read. for a 2 - byte read , only the address of the m ost significant b yte must be loaded into the address pointer register. after the m ost s ignifi- cant b yte is read, the address pointer is auto - incremented so that the l east s ignificant b yte can read within the same transaction. bit 0 to bit 2 are event alarm flags for t low , t high , and t crit . when the adc is configured to convert the temperature to a 16 - bit digital value , then bit 0 to bit 2 are no longer used as flag bits and are instead used a s the lsbs for the extended digital value. table 8 . temperature value msb register ( register address 0x00) bit default value type name description [ 14: 8 ] 0000000 r temp temperature value in twos complement format 15 0 r sign s ign bit, indicates if the temperature value is negative or positive table 9 . temperature value lsb register ( register address 0x01) bit default value type name description 0 0 r t low flag/lsb0 flags a t low event if the configur ation register, register address 0x03[7] = 0 (13 - bit resolution). when the temperature value is below t low , this bit it set to 1. contains the least significant bit 0 of the 15 - bit temperature value if the configuration register, register address 0x03 [7] = 1 (16 - bit resolution). 1 0 r t high flag/lsb1 flags a t high event if the configuration register, register address 0x03[7] = 0 (13 - bit resolution). when the temperature value is above t high , this bit it set to 1. contains the least significant bi t 1 of the 15 - bit temperature value if the configuration register, register address 0x03[7] = 1 (16 - bit resolution). 2 0 r t crit flag/lsb2 flags a t crit event if the configuration register, register address 0x03[7] = 0 (13 - bit resolution). when the temper ature value exceeds t crit , this bit it set to 1. contains the least significant bit 2 of the 15 - bit temperature value if the config uration register, register address 0x03[7] = 1 (16 - b it resolution). [ 7:3 ] 00000 r temp temperature value in twos comple ment format.
adt7420 data sheet rev. 0 | page 14 of 24 status register this 8 - bit read - only register reflects the status of the overtempera - ture and undertemperature interrupts that can cause the ct and int pins to go active. it also reflects the status of a temperature conversion operation. th e interrupt flags in this register are reset by a read operation to the status register and/or when the temperature value returns within the temperature limits, including hysteresis. the rdy bit is reset after a read from the temperature value register. in one - shot and 1 sps modes, the rdy bit is reset after a write to the operation mode bits. configuration regist er this 8 - bit read/write register stores various configuration modes for the adt7420 , including shutdown, overtemperature and undertemperature interrupts, one - shot, continuous conversion, interrupt pins polarity, and overtemperature fault queues. table 10 . status register ( register address 0x 02) bit default value type name description [ 3 : 0 ] 0000 r unused reads back 0. 4 0 r t low this bit is set to 1 when the temperature goes below the t low temperature limit. the bit clears to 0 when the status register is read and/or when the temperature measured goes back above the limit set in the setpoint t low + t hyst registers. 5 0 r t high this bit is set to 1 when the temperature goes above the t high temperature limit. the bit clears to 0 when the status register is read and/or when the temperature measured goes back below the limit set in the setpoint t high ? t hyst registers. 6 0 r t crit this bit is set to 1 when the temperature goes above the t crit temperature limit. this bit clears to 0 when the status register is read and/or when the temperatur e measured goes back below the limit set in the setpoint t crit ? t hyst registers. 7 1 r rdy this bit goes low when the temperature conversion result is written into the temperature value register. it is reset to 1 when the temperature va lue register is read. in one - shot and 1 sps modes, this bit is reset after a write to the operation mode bits. table 11 . configuration register ( register address 0x03) bit default value type name description [1 : 0 ] 00 r/ w fault queue t hese two bits set the number of undertemperature/ overtemperature faults that can occur bef ore setting the int and ct pins. this helps to avoid false triggering due to temperature noise. 00 = 1 fault (default) . 01 = 2 fa ults . 10 = 3 faults . 11 = 4 faults . 2 0 r/ w ct pin polarity this bit selects the output polarity of the ct pin. 0 = active low . 1 = active high . 3 0 r/ w int pin polarity this bit selects the output polarity of the int pin. 0 = active low . 1 = active high . 4 0 r/ w int/ct mode this bit selects between comparator mode and interrupt mode. 0 = interrupt mode 1 = comparator mode [6 : 5 ] 00 r/ w operat ion mode these two bits set the operational mode for the adt7420 . 00 = continuous conversion (default). when one conversion is finished, the adt7420 starts a nother. 01 = one shot. conversion time is typically 240 ms. 10 = 1 sps m ode. conversion time is typically 60 m s. this operational mode reduces the average current consumption. 11 = sh utdown. all circuitry except interface circuitry is powere d down. 7 0 r/ w resolution this bit sets up the resolution of the adc when converting. 0 = 13 - bit resolution. sign bit + 12 bits gives a temperature resolution of 0.0625c. 1 = 16 - bit resolution. sign bit + 15 bits gives a tem p erature resolution of 0.0078 c.
data sheet adt7420 rev. 0 | page 15 of 24 t high setpoint registers the t high setpoint msb and t high setpoint lsb registers store the overtempera ture limit value. an overtemperature event occurs when the temperature value stored in the temperature value register e xceeds the value stored in this register. the int pin is activated if an overtemperature event occurs. the temper - ature is stored in twos complement format with the msb being the temperature sign bit. when reading from this register, the eight most signi ficant bits (bit 15 to bit 8) are read first from register address 0x04 and then the eight least significant bits (bit 7 to bit 0) are read from register address 0x05 (t high setpoint lsb ) . only register address 0x04 (t high setpoint msb) needs to be loaded into the address pointer register because the address pointer auto - increments to register address 0x05 (t high setpoint lsb). the default setting for the t high setpoint is 64c. t low setpoint registers the t low setpoint msb and t low setpoint lsb register s store the undertemperature limit value. an undertemperature event occurs when the temperature value stored in the temperature value register is less than the value stored in this register. the int pin is activated if an undertemperature event occurs. the temperature is stored in twos complement format with the msb being the temperature sign bit. when reading from this register, the eight most significant bits (bit 15 to bit 8) are read first from register address 0x06 and then the eight least significant bits (bit 7 to bit 0) are read from register address 0x07. only register address 0x06 (t low setpoint msb) needs to be loaded into the address pointer register because the address pointer auto - increments to register address 0x07 (t low setpoint lsb). the de fault setting for the t low setpoint is 10c. t crit setpoint registers the t crit setpoint msb and t crit setpoint lsb registers store the critical overtemperature limit value. a critical overtempe - rature event occurs when the temperature value stored in the temperature value register exceeds the value stored in this register. the ct pin is activated if a critical overtemperature event occurs. the temperature is stored in twos complement format with the msb being the temperature sign bit. when reading from th is register, the eight most significant bits (bit 15 to bit 8) are read first from register address 0x08 (t crit setpoint msb ) and then the eight least significant bits (bit 7 to bit 0) are read from register address 0x09 (t crit setpoint lsb). only registe r address 0x08 (t crit setpoint msb) needs to be loaded into the address pointer register because the address pointer auto - increments to register address 0x09 (t crit setpoint lsb). the default setting for the t crit limit is 147c. table 12. t high setpoint msb register ( register address 0x04) bit default value type name description [15:8] 0x20 r/ w t high msb msbs of the overtemperature limit, stored in twos complement format. table 13. t high setpoint lsb register ( register address 0x05 ) bit default value type name description [7:0] 0x00 r/ w t high lsb lsbs of the overtemperature limit, stored in twos complement format. table 14. t low setpoi nt msb register ( register address 0x06) bit default value type name description [15:8] 0x05 r/ w t low msb msbs of the undertemperature limit, stored in twos complement format. table 15. t low setpoint lsb regi ster (register address 0x07) bit default value type name description [7:0] 0x00 r/ w t low lsb lsbs of the undertemperature limit, stored in twos complement format. table 16. t crit setpoint msb register ( regist er address 0x08) bit default value type name description [15:8] 0x49 r/ w t crit msb msbs of the critical overtemperature limit, stored in twos complement format. table 17. t crit setpoint lsb register ( registe r address 0x09) bit default value type name description [7:0] 0x80 r/ w t crit lsb lsbs of the critical overtemperature limit, stored in twos complement format.
adt7420 data sheet rev. 0 | page 16 of 24 t hyst setpoint register this 8 - bit read/write register stores the t emperature hysteresis value for the t high , t low , and t crit temperature limits. the temperature hysteresis value is stored in straight binary format using four lsbs. increments are possible in steps of 1c from 0c to 15c. the value in this register is sub tracted from the t high and t crit values and added to the t low value to imple - ment hysteresis. id register this 8 - bit read - only register stores the manufacture id in bit 3 to bit 7 and the silicon revision in bit 0 to bit 2. the default setting for the id register is 0xcb. table 18. t hyst setpoint register ( register address 0x0a) bit default value type name description [3:0] 0101 r/ w t hyst hysteresis value, from 0c to 15c. stored in straight binary format. the default setting is 5c. [7:4] 0000 r/ w n/a not used. table 19 . id register ( register address 0x0b) bit default value type name description [2:0] 011 r revision id contains the silicon revision identific ation number [7:3] 11001 r manufacture id contains the manufacture identification number
data sheet adt7420 rev. 0 | page 17 of 24 serial interface adt7420 sc l ct int a1 a0 sd a gnd v dd 10k 10k 10k pull-u p v dd pull-u p v dd 0.1f 10k pull-u p v dd t o interrupt pin on microcontroller v dd 09013-014 figure 13 . typical i 2 c interface connection control of the adt7420 is carried out via the i 2 c - compatible serial interface. the adt7420 is connected to this bus as a slave and is under the control of a master device. figure 13 shows a typ ical i 2 c interface connection. serial bus address like most i 2 c - compatible devices, the adt7420 has a 7 - bit serial address. the five msbs of this address for the adt7420 are hardwired internally to 10010. pin a1 and pin a0 set the two lsbs. these pins can be configured two ways, low and high, to give four different address options. table 20 shows the different bus address opt ions available. the recommended pull - up re sistor value on the sda and scl lines is 10 k?. table 20. i 2 c bus address options binary hex a6 a5 a4 a3 a2 a1 a0 1 0 0 1 0 0 0 0x48 1 0 0 1 0 0 1 0x49 1 0 0 1 0 1 0 0x4a 1 0 0 1 0 1 1 0x4b the serial bus protocol operates as follows: 1. the master initiates data transfer by establishing a start condition, defined as a high - to - low transition on the serial data line , sda, while the serial clock line, scl, remains high. this indicates that an address/data stream is going to follow . all slave peripherals connected to the serial bus respond to the start condition and shift in the next eight bits, consisting of a 7 - bit address (msb first) plus a read/ write (r/ w ) bit. the r/ w bit determines whether data is written to, or read from, the slave device. 2. the peripheral with the address corresponding to the transmitted address responds by pulling the data line low during the low period before the ninth clock pulse, known as the acknowledge bit. all other devices on the bus then remain idle while the selected device waits for data to be read from or written to it. if the r/ w bit is a 0 , the master writes to the slave device. if the r/ w bit is a 1 , the master reads from t he slave device. 3. data is sent over the serial bus in sequences of nine clock pulses, eight bits of data followed by an acknowledge bit from the receiver of data. transitions on the data line must occur during the low period of the clock signal and remain s table during the high period as a low - to - high transition when the clock is high, which can be interpreted as a stop signal. 4. when all data bytes have been read or written, stop condi - tions are established. in write mode, the master pulls the data line high during the 10 th clock pulse to assert a stop condition. in read mode, the master device pulls the data line high during the low period before the ninth clock pulse. this is known as a no acknowledge. the master takes the data line low during the low period before the 10 th clock pulse, then high during the 10 th clock pulse to assert a stop condition. it is not possible to mix read and write in one operation because the type of operation is determined at the beginning and cannot subsequently be changed witho ut starting a new operation.
adt7420 data sheet rev. 0 | page 18 of 24 writing data it is possible to write either a single byte of data or two bytes to the adt7420 , depending on which registers are to be written. writing a single byte of data requires the serial bus address, the data register address written to the address pointer register, followed by the data byte written to the selected data register. this is shown in figure 14. for the t high setpoint, t low setpoint, and t crit setpoint registers, it is possible to write to both the msb and the lsb registers in the same write transaction. writing two bytes of data to these registers requires the serial bus address, the data register address of the msb register written to the address pointer register, followed by the two data bytes written to the selected data register. this is shown in figure 15. if more than the required number of data bytes is written to a register, the register ignores these extra data bytes. to write to a different register, a start or repeated start is required. frame 1 serial bus address byte frame 2 address pointer register byte ack. by adt7420 ack. by adt7420 ack. by adt7420 stop by master frame 3 data byte sda (continued) scl (continued) scl sda start by master 1 0 0 1 0 a1a0 p7p6p5p4p3p2p1p0 9 d7 d6 d5 d4 d3 d2 d1 d0 r/w 19 1 9 1 09013-016 figure 14. writing to a register followed by a single byte of data frame 1 serial bus address byte frame 2 address pointer register byte ack. by adt7420 ack. by adt7420 ack. by adt7420 stop by master frame 4 data byte scl sda start by master 1 0 0 1 0 a1a0 p7p6p5p4p3p2p1p0 9 d7 d6 d5 d4 d3 d2 d1 d0 r/w 19 1 9 1 ack. by adt7420 frame 3 data byte sda (continued) scl (continued) d15 d14 d13 d12 d11 d10 d9 d8 9 1 09013-017 figure 15. writing to a register followed by two bytes of data
data sheet adt7420 rev. 0 | page 19 of 24 reading data reading data from the adt7420 is done in a single data byte operation for the configuration register, the status register, the t hyst setpoint register, and the id register. a two data byte read operation is needed for the temperature value register, t high setpoint register, t low setpoint register, and the t crit setpoint register. reading back the contents of an 8-bit register similar to the configuration register is shown in figure 16. reading back the contents of the temperature value register is shown in figure 17. reading back from any register first requires a single-byte write operation to the address pointer register to set up the address of the register that is going to be read from. in the case of reading back from the 2-byte registers, the address pointer automatically increments from the msb register address to the lsb register address. to read from another register, execute another write to the address pointer register to set up the relevant register address. thus, block reads are not possible, that is, there is no i 2 c address pointer auto-increment except wh en reading back from a 16-bit register. if the address pointer register has previously been set up with the address of the register that is going to receive a read command, there is no need to repeat a write operation to set up the register address again. scl sda 1 10 01 a1 0a0 repeat start by master frame 3 serial bus address byte frame 4 data byte from configuration register stop by master ack. by adt7420 no ack. by master r/w d7d6 d5d4d3d2 d1d0 99 1 scl sda 1 10 01 a1a0 start by master frame 1 serial bus address byte frame 2 address pointer register byte ack. by adt7420 ack. by adt7420 r/w p7p6 p5p4p3p2 p1p0 99 1 0 09013-018 figure 16. reading back data fr om the configuration register notes 1. a start condition at the beginning is defined as a high-to-low transition on sda while scl remains high. 2. a stop condition at the end is defined as a low-to-high transition on sda while scl remains high. 3. the master generates the no acknowledge at the end of the readback to signal that it does not want additional data. 4. temperature value register msb data and temperature valiue register lsb data are always separated by a low ack bit. 5. the r/w bit is set to a1 to indicate a readback operation. sda 100 r/w a7 a6 scl sda scl 1 a1 a0 11 0a1a0 9 adt7410 device address register address[a7:a0] d1 d0 d7 d6 temperature value register msb data 9 1 1 9 9 0 1a1a0 r/w repeat start d1 d0 d7 d6 ack. by adt7420 ack. by master no ack. by master ack. by adt7420 start adt7410 device address ack. by adt7420 temperature value register lsb data sr 09013-023 figure 17. reading back data from the temperature value register
adt7420 data sheet rev. 0 | page 20 of 24 reset to r eset the adt7420 without having to reset the entire i 2 c bu s, an explicit reset command is provided. this uses a particular address pointer word as a command word to reset the part and upload all default settings. the adt7420 does not re spond to (does not acknowledge) i 2 c bus comma nds while the default values upload for approximately 200 s. use t he following sequence to perform a reset: 1. write to the adt7420 us ing the appropriate address. 2. get acknowledge. 3. set the register address to 0x2f . 4. get acknowledge. 5. apply stop condition . 6. wait 200 s for the part to reset its registers to the default power - up settings. general call when a master issues a slave address cons isting of seven 0s with the eighth bit (r/ w bit) set to 0, this is known as the general call address. the general call address is for addressing every device conne cted to the i 2 c bus. the adt7 420 acknowledges this addre ss and reads in the following data byte. if the second byte is 0x06, the adt7420 is reset, completely uploading all default values. the adt7420 does not respond to the i 2 c bus commands (do not acknowledge) while the default values upload for approximately 200 s. the adt7420 does not acknowledge any other general call commands.
data sheet adt7420 rev. 0 | page 21 of 24 int and ct outputs the int and ct pins are open - drain outputs , and both pins require a 10 k? pull - up resistor to v dd . the adt7420 must be fully powered up to v dd before reading int and ct data. undertemperature and ov ertemperature detection the int and ct pins have two undertemperature/ overtempera - ture modes: comparator mode and interrupt mode. the interrupt mode is the default power - up overtemperature mode. the int output pin becomes active when the temperature is gre ater than the temperature stored in the t high setpoint register or less than the temperature stored in the t low setpoint register. how this pin reacts after this event depends on the overtempera ture mode selected. figure 18 illustrates the comparator and interrupt modes for events exceeding the t high limit with both pin polarity settings. figure 19 illustrates the comparator and interrupt modes for events exceeding the t low limit with both pin polarity settings. comparator mode in comparator mode, the int pin returns to its inactive status when the temperature drops below the t high ? t hyst limit or rises above the t low + t hyst limit. putting the adt7420 into shutdown mode does not reset the int state in comparator mode. interrupt mode in interrupt mode, the int pin goes inactive when an y adt7420 register is read. once the int pin is reset, it goes active again only w hen the temperature is greater than the temperature stored in the t high setpoint register or less than the temperature stored i n the t low setpoint register. placing the adt7420 into shutdown mode resets the int pin in the interrupt mode. temper a ture 82c 81c 80c 79c 78c 77c 76c 75c 74c 73c int pin (com p ar a t or mode) polarit y = active low int pin (interrupt mode) polarit y = active low int pin (interrupt mode) polarit y = active high int pin (com p ar a t or mode) polarit y = active high t high t high ? t hyst time read read read 09013-020 figure 18 . int output temperature response diagram for t high overtemp erature events
adt7420 data sheet rev. 0 | page 22 of 24 temper a ture ?13c ?14c ?15c ?16c ?17c ?18c ?19c ?20c ?21c ?22c int pin (com p ar a t or mode) polarit y = active low int pin (interrupt mode) polarit y = active low int pin (interrupt mode) polarit y = active high int pin (com p ar a t or mode) polarit y = active high t low + t hyst t low time read read read 09013-021 figure 19 . int output temperature response diagram for t low under temperature events
data sheet adt7420 rev. 0 | page 23 of 24 applications informa tion thermal response tim e thermal response is a function of the thermal mass of the temperature sensor, b ut it is also heavily influenced by the mass of the object the ic is mounted to. for example, a large pcb containing large amounts of copper tracking can act as a large heat sink and slow the thermal response. for a faster thermal response, it is recommen ded to mount the sensor on as small a pcb as possible. figure 10 shows the typical response time of less than two seconds to reach 63.2% of its temperature span. the tempera - ture value is read back as a 16 - bit val ue through the digital interface. the response time includes all delays incurred on chip during signal processing. supply decoupling the adt7420 must have a decoupling capacitor connected between v dd and gnd; otherwise , incorrect temperature readings will be obtained. a 0.1 f decoupling capacitor such as a high frequency ceramic type must be used and mounted as close as possible to the v dd pin of the adt7420 . if possible, the adt7420 should be powered directly from the system power supply. this arrangement, shown in figure 20, isolates the analog section from the logic - switchi ng transients. even if a separate power supply trace is not available, generous supply bypassing reduces supply - line induced errors. local supply bypassing consisting of a 0.1 f ceramic capacitor is critical for the temperature accuracy specifications to be achieved. 0.1f adt7420 ttl/cmos logic circuits power supp l y 09013-022 figure 20 . use of separate traces to reduce power supply noise p owering from a switc hing regulator precision analog devices , such as the adt7420 require a well - filtere d power source. if the adt7420 is powered from a switching regulator, noise may be generated above 50 khz that may affect the temperature accuracy specification s . to pre ve nt this, an rc filter should be used b etween the power supply and adt7420 v dd . the value of the components used should be carefully considered to ensure that the peak value of the supply noise is less than 1 mv. the rc filter should be mounted as far away as possible from the adt7420 to ensure that the thermal mass is kept as low as possible. temperature measurem ent the adt7420 accurately measures and conv erts the tempera - ture at the surface of its own semiconductor chip. thermal paths run through the leads, the exposed pad, as well as the plastic package. when the adt7420 is used to measure the temperature of a nearby heat source, the thermal impedance between the heat source and the adt7420 must be considered because this impacts the accuracy and thermal response of the measurement. for air or surface temperatur e measurements, take care to isolate the package, leads, and exposed pad from ambient air temperature. use of a thermally conductive adhesive can help to achieve a more accurate surface temperature measurement. quick g uide to m easuring t emperature the fol lowing is a quick guide for measuring temperature in continuous conversion mode (default power - up mode). execute each step sequentially. 1. after powe ring up the adt7420 , v erify the setup by reading the device id (register address 0x0b). it should read 0xcb . 2. after consist e nt consecutive r eadings are obtained from step 1 , proceed to read the configuration register (0x0 3 ) , t crit (0x08, 0x09) , t high (0x04, 0x05) , and t low (0x06, 0x07) registers. compare to the speci fied defaults in table 6 . if all the readings match, the interface is operational . 3. write to the configuration register to set the adt7420 to the desired configuration. 4. read the temperature value msb register , followed by the temperature value lsb register. both registers should produce a valid temperature measurement.
adt7420 data sheet rev. 0 | page 24 of 24 outline dimensions 2.70 2.60 sq 2.50 compliant to jedec standards mo-220-wggc. 012909-b 1 0.65 bsc bottom view top view 16 5 8 9 12 13 4 exposed pad p i n 1 i n d i c a t o r 4.10 4.00 sq 3.90 0.45 0.40 0.35 s eating plane 0.80 0.75 0.70 0.05 max 0.02 nom 0.20 ref 0.25 min coplanarity 0.08 pin 1 indi c ator 0.35 0.30 0.25 for proper connection of the exposed pad, refer to the pin configuration and function descriptions section of this data sheet. figure 21. 16-lead lead frame chip scale package [lfcsp_wq] 4 mm 4 mm body, very thin quad (cp-16-17) dimensions shown in millimeters ordering guide model 1 operating temperature range package description package option adt7420ucpz-r2 ?40c to +150c 16-lead lfcsp_wq cp-16-17 adt7420ucpz-rl7 ?40c to +150c 16-lead lfcsp_wq cp-16-17 EVAL-ADT7X20EBZ evaluation board 1 z = rohs compliant part. i 2 c refers to a communications protocol originally developed by philips semiconductors (now nxp semiconductors). ?2012 analog devices, inc. all rights reserved. trademarks and registered trademarks are the prop erty of their respective owners. d09013-0-12/12(0)

▲Up To Search▲

Price & Availability of EVAL-ADT7X20EBZ

	To Download EVAL-ADT7X20EBZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .