rev c pol10 - 12t series 10a output current rating dc/dc open frame power supply single output 1/9/2018 wall industries, inc. ? 37 industr ial drive, exeter, nh 03833 ? tel: 603 - 778 - 2300 ? toll free: 888 - 597 - 9255 ? fax 603 - 778 - 9797 website: www.wallindustries.com ? e - mail: sales@wallindustries.com page 1 of 5 smt package vertical sip package horizontal sip package size: 1.30in x 0.53in x 0.30 in size: 2.00in x 0.50in x 0.28 in size: 2.00in x 0.50in x 0.28 in options features ? smd or sip package ? vertical or horizontal option available for sip package ? remote control: positive or negative logic ? ? ? ? ? ? ? ? ? ? ? telecom/datacom ? industry control system ? distributed power architectures ? semiconductor equipment ? microprocessor power applications the pol10 - 12t series of dc/dc open frame power supplies offers a 10a output current rating in a small size and low profile package. this series consists of single output models with and input vol tage range of 8.3~14vdc or 8.3~13.2vdc. several options are available for this series including remote control positive or negative logic and smd or sip package. each model is rohs ii & reach compliant, ce marked, and has over load, over temperature, and s hort circuit protection. this series has ul60950 - 1, en60950 - 1, and iec60950 - 1 safety approvals. model selection table model number input voltage range output voltage output current @full load no load input current 0.75vdc/5.0vdc package type maximum ca pacitive load (1) efficiency (2) remote on/off pols10 - 12t vout 3.63 vin=8.3~14vdc vout>3.63 vin=8.3~13.2 0.75~5vdc 10a 40/100 smd 1000/5000 f 93% positive pols10 - 12t - p negat ive polt10 - 12t 0.75~5vdc 10a 40/100 vertical sip 1000/5000 f 93% positive polt10 - 12t - p negative polt10 - 12ta 0.75~5vdc 10a 40/100 horizontal sip 1000/5000 f 93% positive polt10 - 12ta - p negative
rev c pol10 - 12t series 10a output current rating dc/dc open frame power supply single output 1/9/2018 wall industries, inc. ? 37 industr ial drive, exeter, nh 03833 ? tel: 603 - 778 - 2300 ? toll free: 888 - 597 - 9255 ? fax 603 - 778 - 9797 website: www.wallindustries.com ? e - mail: sales@wallindustries.com page 2 of 5 specifications all specifications are based on 25c, nominal input voltage, and maximum output current u nless otherwise noted. we reserve the right to change specifications based on technological advances. specification test conditions min typ max unit input specifications input voltage range vout(set) 100 mv 50% load step change setting time (vout<10% peak deviation) 25 s temperature coefficient - 0.4 +0.4 %/ o c rise time time for vout to rise from 10% to 90% of vout(set) 6 ms output voltage overshoot - startup vin=vin(min.) to vin(max.) at full load; % of vout(set) 1.0 % remote on/off control (5)(6 ) negative logic ( option ) dc - dc on open or 0~0.3vdc dc - dc off 2.5vdc~vin(max.) positive logic (standard ) dc - dc on open or (vin - 4)~vin(max.) dc - dc off 0~0.3vdc input current o f ctrl pin 0.01 1.0 ma remote off input current 2.0 ma protection short circuit protection continuous, automatic recovery over load protection % of iout rated 200 % over temperature protection 125 o c environmental specifications operating case temperature with derating - 40 +85 o c storage temperature - 55 +125 o c relative humidity 5 95 %rh thermal shock mil - std - 810f vibration mil - std - 810f mtbf mil - hdbk - 217f, full load 3,355,000 hours general specifications efficiency see tab le switching frequency 270 300 330 khz physical specifications weight 0.21oz (6.0g) dimensions (l x w x h) sm t package 1.30in x 0.53in x 0.30in (33mm x 13.5mm x 7.6mm) sip package 2.00in x 0.50in x 0.28in (50.8mm x 12.7mm x 7.2mm) safety c haract eristics safety approvals ul60950 - 1, en60950 - 1, iec60950 - 1 lead - free reflow solder process ipc j - std - 020d moisture sensitivity level (msl) ipc j - std - 033b, level 2a
rev c pol10 - 12t series 10a output current rating dc/dc open frame power supply single output 1/9/2018 wall industries, inc. ? 37 industr ial drive, exeter, nh 03833 ? tel: 603 - 778 - 2300 ? toll free: 888 - 597 - 9255 ? fax 603 - 778 - 9797 website: www.wallindustries.com ? e - mail: sales@wallindustries.com page 3 of 5 notes 1. efficiency vin(nom), 3.3vdc 2. test by minimum input and constant resistive lo ad. esr1m / esr10m 3. it?s necessary to equip the external input capacitors at the input of the module. the capacitors should connect as close as p ossible to the input terminals that ensure module stability. the external cin is 4pcs of 47f ceramic capaci tors at least. 4. output voltage is programmable from 0.7525v to 5v by connecting a single resistor (shown as trim table) between the trim and gnd pins of the module. to calculate the value of the resistor rtrim for a particular output voltage vout, use the following equation. trim figure trim table 5. remote on/off referred to ? vin pin 6. positive logic: on/off is open collector/drain logic input negative logic: on/off is open collector/drain logic input with external pull ? up resistor * due to advances in technology, specifications subject to change without notice. derating curves pols10 - 12t, vout=3.3v derating curve pol s10 - 12t, vout=3.3v efficiency vs. input voltage pols10 - 12t, vout=3.3v efficiency vs. output load
rev c pol10 - 12t series 10a output current rating dc/dc open frame power supply single output 1/9/2018 wall industries, inc. ? 37 industr ial drive, exeter, nh 03833 ? tel: 603 - 778 - 2300 ? toll free: 888 - 597 - 9255 ? fax 603 - 778 - 9797 website: www.wallindustries.com ? e - mail: sales@wallindustries.com page 4 of 5 mechanical drawing s pols10 - 12t pin connection pin define 1 ctrl 2 +sense 3 trim 4 +vout 5 gnd 6 +vin p olt10 - 12t pin connection pin define 1 +vout 2 +vout 3 +sense 4 +vout 5 gnd 6 gnd 7 +vin 8 +vin 10 trim 11 ctrl polt - 12ta pin connection pin define 1 +vout 2 +vout 3 +sense 4 +vout 5 gnd 6 gnd 7 +vin 8 +vin 10 trim 11 ctrl notes: all dimensions in inch (mm) tolerance: x.xx0.02 (x.x0.5) x.xxx0.01 (x.xx0.25) pin pitch tolerance 0.01 (0.25) pin dimension tolerance 0.004(0.1)
rev c pol10 - 12t series 10a output current rating dc/dc open frame power supply single output 1/9/2018 wall industries, inc. ? 37 industr ial drive, exeter, nh 03833 ? tel: 603 - 778 - 2300 ? toll free: 888 - 597 - 9255 ? fax 603 - 778 - 9797 website: www.wallindustries.com ? e - mail: sales@wallindustries.com page 5 of 5 model number setup polt 10 - 12 t - p series name output cur r ent input voltage package remote on/off option polt: smd type 12: 8.3~14vdc t: no assembly (smd type) none: positive logic pols: sip type t: verti cal mounting (sip type) p: negative logic ta: horizontal mounting (sip type) company information wall industries, inc. has created custom and modified units for over 50 years. our in - house r esearch and development engineers will provide a solution that exceeds your performance requirements on - time and on budget. our iso9001 - 2008 certification is just one example of our commitment to producing a high quality, well - documented product for our cu stomers. our past projects demonstrate our commitment to you, our customer. wall industries, inc. has a reputation for working closely with its customers to e nsure each solution meets or exceeds form, fit and function requirements. we will continue to provide ongoing support for your project above and beyond the design and production phases. give us a call today to discuss your future projects. contact wall i ndustries for further information: phone: ? (603)778- 2300 toll free: ? (888)597 - 9255 fax: ? (603)778- 9797 e - mail: sales@wallindustries.com web: www.wallindustries. com address: 37 industrial drive exeter, nh 03833
|
