qpl9096 ultra low - noise, bypass lna d ata sheet ju ly 5 , 201 7 | subject to change without notice 1 of 10 www.qorvo.com 8 pin 2x2 mm dfn p ackage general description the qpl9096 is a high - linearity, ultra - low noise gain block amplifier with a bypass mode functionality integrated in the product. at 2.5 ? ghz, the amplifier typically provides 2 5 db gain, +3 3.5 dbm oip3, and 0. 7 5 db noise figure while drawing 60 ma current from a + 4.2 ? v supply. the qpl9096 is internally matched using a high performance e - phemt process and only requires four external components for operation from a single positive supply: an external rf choke and blocking/bypass capacitors. this low noise amplifier contains an internal acti ve bias to maintain high performance over temperature. the qpl9096 is optimized for the 1 .7? C ? 2.7 ghz frequency band and is targeted for wireless infrastruc ture. the qpl9096 is packaged in a 2?x?2?mm dfn. applications ? base - station receivers ? repeaters / das ? tower mounted amplifiers ? mobile infrastructure ? general purpose wireless ? tdd or fdd systems product features ? 1 .7 C 2.7 ghz operational bandwidth ? lna with integrated bypass mode ? ability to turn lna and bypass mode off ? ultra low noise, 0.7 5 db at 2.5 ?ghz ? 2 5 db gain at 2.5 ?ghz ? +3 3.5 dbm output ip3 in lna mode ? + 40 dbm input ip3 in bypass mode ? internally matched ? positive supply only, +3.3 to +5?v ? 2x2 mm 8 - pin dfn plastic package functional block diagram top view ordering information part no. description qpl9096 sr 100 pcs on 7 reel qpl9096 tr7 2500 pcs on 7 reel QPL9096EVB01 (1) evaluation board 1. refer board details and performance on pgs. 3 & 4. ? b a c k s i d e p a d d l e - r f / d c g n d p i n 1 r e f e r e n c e m a r k 8 7 6 5 1 2 3 4 v d d r f o u t g n d v s d g n d r f i n n / c v b y p
qpl9096 ultra low - noise, bypass lna d ata sheet ju ly 5 , 201 7 | subject to change without notice 2 of 10 www.qorvo.com absolute maximum ratings parameter rating storage temperature ?6 5 to 150c supply voltage (v dd ) + 7 v rf input power, cw, 50, t=25 c +30 dbm operation of this device outside the parameter ranges given above may cause permanent damage. recommended operating conditions parameter min typ max units supply voltage (v dd ) 3. 0 4.2 5.25 v t case ? 40 + 105 c t j at t case = 125 c + 14 2 c electrical specifications are measured at specified test conditions. specifications are not guaranteed over all recommended operating conditions. electrical specifications test conditions unless otherwise noted: v dd = +4.2 v, temp.=+ 25 c . parameter conditions min typ max units operational frequency range 1700 27 00 mhz test frequency 2500 mhz gain lna on, bypass off 23.5 25 26.5 db input return loss lna on, bypass off 20 db output return loss lna on, bypass off 6 db noise figure (2) lna on, bypass off 0.75 1.1 db output p1db lna on, bypass off +15.5 (1) + 17 dbm output ip3 lna on, bypass off, pout=+0 dbm/tone, f= 5 mhz +30 +33.5 dbm insertion loss lna off, bypass on 1.4 3 db return loss lna off, bypass on 12 db isolation (1) lna off, bypass off 15 18 db output ip3 lna off, bypass on pin=+3 dbm/tone, f= 5 mhz +33 +40 dbm control voltage, v 1 , v 2 v ih 1.17 v dd v v il 0 0. 63 v current, i d bypass off 40 55 75 ma bypass on 3.5 ma switching speed lna - bypass (50% vctrl to 10% rf) 200 ns bypass - lna(50% vctrl to 90% rf) 330 ns lna - off(50% vctrl to 10% rf) 26 ns off - lna(50% vctrl to 90% rf) 65 ns thermal resistance, jc channel to case 44 c/w 1. minimum specification listed is guaranteed by design. not tested in production. 2. input trace loss de - embedded from noise figure data. control truth table v byp v sd state 0 0 lna on, bypass off 0 1 lna off, bypass off 1 x lna off, bypass on ?
qpl9096 ultra low - noise, bypass lna d ata sheet ju ly 5 , 201 7 | subject to change without notice 3 of 10 www.qorvo.com qpl9096 evaluation board notes: 1. a through line is included on the evaluation board to de - embed the board losses. bill of material C qpl9096 evaluation board reference des. value description manuf. part number n/a n/a printed circuit board qorvo u1 n/a ultra low noise, bypass lna qorvo qpl9096 c 1, c 4 , c5, c8 22 pf cap, 0402, +/ - 0.1pf, 25v various c9 1000 pf cap, 0402, 10%, 50v, x7r murata grm155r71h102ka01d c 10 1.0 uf cap., 0402, 10%, 6.3 v, x5r murata grm155r60j105ke19d c11, c12 20k res, chip, 0402, 5% various r1, 3, 4 0 resistor, chip, 0402, 5%, 1/16w various l1 18 nh inductor, 0 402 , 5%, coil coilcraft 0402cs - 18nxjl ? l 1 c 1 0 c 9 r 3 u 1 c 8 c 5 c 4 r 4 r 1 c 1 c 1 1 c 1 2 j 2 r f o u t p u t j 6 g n d j 3 v d d j 1 r f i n p u t l 1 1 8 n h ( 0 6 0 3 ) c 4 2 2 p f c 1 2 2 p f c 1 0 1 u f c 9 1 0 0 0 p f r 3 0 ? 8 7 6 5 1 2 3 4 j 5 v 1 j 4 v 2 r 4 0 ? r 1 0 ? u 1 c 1 2 2 0 k c 1 1 2 0 k
qpl9096 ultra low - noise, bypass lna d ata sheet ju ly 5 , 201 7 | subject to change without notice 4 of 10 www.qorvo.com performance plots test conditions unless otherwise noted: v dd = +4.2 v ? 10 15 20 25 30 1500 2000 2500 3000 3500 gain (db) frequency (mhz) gain vs. frequency (lna mode) +95? c +25? c ?40? c -25 -20 -15 -10 -5 0 1500 2000 2500 3000 3500 |s11| (db) frequency (mhz) input return loss vs. frequency (lna mode) +95? c +25? c ?40? c -25 -20 -15 -10 -5 0 1500 2000 2500 3000 3500 |s22| (db) frequency (mhz) output return loss vs. frequency (lna mode) +95? c +25? c ?40? c -3.0 -2.5 -2.0 -1.5 -1.0 -0.5 0.0 1500 2000 2500 3000 3500 insertion loss (db) frequency (mhz) insertion loss vs. frequency (bypass mode) +95? c +25? c ?40? c -15 -10 -5 0 1500 2000 2500 3000 3500 |s11| (db) frequency (mhz) input return loss vs. frequency (bypass mode) +95? c +25? c ?40? c -20 -15 -10 -5 0 1500 2000 2500 3000 3500 |s22| (db) frequency (mhz) output return loss vs. frequency (bypass mode) +95? c +25? c ?40? c -30 -25 -20 -15 -10 1500 2000 2500 3000 3500 gain (db) frequency (mhz) isolation vs. frequency (off mode) +95? c +25? c ?40? c -5 -3 -1 1500 2000 2500 3000 3500 |s11| (db) frequency (mhz) input return loss vs. frequency (off mode) +95? c +25? c ?40? c -5 -4 -3 -2 -1 0 1500 2000 2500 3000 3500 |s22| (db) frequency (mhz) output return loss vs. frequency (off mode) +95? c +25? c ?40? c 25 30 35 40 45 -3 -2 -1 0 1 2 3 4 5 6 7 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tone (lna mode) 1700mhz_-40c 2500mhz_-40c 2700mhz_-40c 1700mhz_25c 2500mhz_25c 2700mhz_25c 1700mhz_95c 2500mhz_95c 2700mhz_95c 25 30 35 40 45 -3 -2 -1 0 1 2 3 4 5 6 7 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tone (bypass mode) 1700mhz_-40c 2500mhz_-40c 2700mhz_-40c 1700mhz_25c 2500mhz_25c 2700mhz_25c 1700mhz_95c 2500mhz_95c 2700mhz_95c 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 noise figure (db) frequency (ghz) noise figure vs frequency +85? c +25? c ?40? c
qpl9096 ultra low - noise, bypass lna d ata sheet ju ly 5 , 201 7 | subject to change without notice 5 of 10 www.qorvo.com qpl9096 1700 - 1900 mhz tune notes: 1. a through line is included on the evaluation board to de - embed the board losses. performance plots - 1700 - 1900 mhz tune test conditions unless otherwise noted: v dd = +4.2 v, temp.=?+25?c ? l 1 c 1 0 c 9 r 3 u 1 c 8 c 5 c 4 r 4 r 1 c 1 c 1 1 c 1 2 l 2 c 1 3 c 1 4 l 3 j 2 r f o u t p u t j 6 g n d j 3 v d d j 1 r f i n p u t l 1 1 8 n h ( 0 6 0 3 ) c 1 4 2 2 p f c 1 2 2 p f c 1 0 1 u f c 9 1 0 0 0 p f r 3 0 ? 8 7 6 5 1 2 3 4 j 5 v 1 j 4 v 2 r 4 0 ? r 1 0 ? u 1 c 1 2 2 0 k c 1 1 2 0 k c 1 3 0 . 8 p f l 3 3 . 9 n h l 2 3 . 3 n h c 4 2 p f -5 0 5 10 15 20 25 1500 1600 1700 1800 1900 2000 gain (db) frequency (mhz) gain vs. frequency bypass mode lna mode -30 -25 -20 -15 -10 -5 0 1600 1700 1800 1900 2000 |s11| & |s22| (db) frequency (mhz) return loss vs. frequency input return loss-bypass mode input return loss-lna mode output return loss-bypass mode output return loss-lna mode 0.5 0.6 0.7 0.8 0.9 1.0 1500 1600 1700 1800 1900 2000 noise figure (db) frequency (mhz) noise figure vs frequency 25 30 35 40 45 -3 -2 -1 0 1 2 3 4 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tone 1700 mhz 1800 mhz 1900 mhz lna mode 25 30 35 40 45 -3 -2 -1 0 1 2 3 4 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tone 1700 mhz 1800 mhz 1900 mhz bypass mode
qpl9096 ultra low - noise, bypass lna d ata sheet ju ly 5 , 201 7 | subject to change without notice 6 of 10 www.qorvo.com qpl9096 1900 - 2100 mhz tune notes: 1. a through line is included on the evaluation board to de - embed the board losses. performance plots - 1900 - 2100 mhz tune test conditions unless otherwise noted: v dd = +4.2 v, temp.=?+25?c ? l 1 c 1 0 c 9 r 3 u 1 c 8 c 5 c 4 r 4 r 1 c 1 c 1 1 c 1 2 l 2 c 1 3 c 1 4 l 3 25 30 35 40 45 -3 -2 -1 0 1 2 3 4 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tone 1700 mhz 1800 mhz 1900 mhz lna mode 25 30 35 40 45 -3 -2 -1 0 1 2 3 4 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tone 1700 mhz 1800 mhz 1900 mhz bypass mode j 2 r f o u t p u t j 6 g n d j 3 v d d j 1 r f i n p u t l 1 1 8 n h ( 0 6 0 3 ) c 1 4 2 2 p f c 1 2 2 p f c 1 0 1 u f c 9 1 0 0 0 p f r 3 0 ? 8 7 6 5 1 2 3 4 j 5 v 1 j 4 v 2 r 4 0 ? r 1 0 ? u 1 c 1 2 2 0 k c 1 1 2 0 k c 1 3 0 . 8 p f l 3 3 . 3 n h l 2 3 . 3 n h c 4 2 p f -5 0 5 10 15 20 25 1800 1900 2000 2100 2200 gain (db) frequency (mhz) gain vs. frequency bypass mode lna mode -30 -25 -20 -15 -10 -5 0 1800 1900 2000 2100 2200 |s11| & |s22| (db) frequency (mhz) return loss vs. frequency input return loss-bypass mode input return loss-bypass mode output return loss-bypass mode output return loss-lna mode 0.5 0.6 0.7 0.8 0.9 1.0 1800 1900 2000 2100 2200 noise figure (db) frequency (mhz) noise figure vs frequency
qpl9096 ultra low - noise, bypass lna d ata sheet ju ly 5 , 201 7 | subject to change without notice 7 of 10 www.qorvo.com qpl9096 2500 - 2700 mhz tune notes: 1. a through line is included on the evaluation board to de - embed the board losses. performance plots 2500 - 2700 mhz tune test conditions unless otherwise noted: v dd = +4.2 v, temp.=?+25?c ? l 1 c 1 0 c 9 r 3 u 1 c 8 c 5 c 4 r 4 r 1 c 1 c 1 1 c 1 2 c 1 4 l 3 c 1 5 j 2 r f o u t p u t j 6 g n d j 3 v d d j 1 r f i n p u t l 1 1 8 n h ( 0 6 0 3 ) c 1 4 2 . 7 p f c 1 2 2 p f c 1 0 1 u f c 9 1 0 0 0 p f r 3 0 ? 8 7 6 5 1 2 3 4 j 5 v 1 j 4 v 2 r 4 0 ? r 1 0 ? u 1 c 1 2 2 0 k c 1 1 2 0 k l 3 1 . 5 n h c 1 5 6 . 8 p f -5 0 5 10 15 20 25 30 2400 2500 2600 2700 2800 gain (db) frequency (mhz) gain vs. frequency bypass mode lna mode -25 -20 -15 -10 -5 0 2400 2500 2600 2700 2800 |s11| & |s22| (db) frequency (mhz) return loss vs. frequency input return loss-bypass mode input return loss-lna mode output return loss-bypass mode output return loss-lna mode 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 2400 2500 2600 2700 2800 noise figure (db) frequency (mhz) noise figure vs frequency 28 30 32 34 36 38 -3 -2 -1 0 1 2 3 4 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tome 2500 mhz 2600 mhz 2700 mhz lna mode 30 32 34 36 38 40 42 44 46 -3 -2 -1 0 1 2 3 4 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tome 2500 mhz 2600 mhz 2700 mhz bypass mode
qpl9096 ultra low - noise, bypass lna d ata sheet ju ly 5 , 201 7 | subject to change without notice 8 of 10 www.qorvo.com evaluation board pcb information qorvo pcb 28 1865 material and stack - up 50 ohm line dimensions: width = 0.0 182 , spacing = 0.0 20 pin configuration and description pin no. label description 1, 6 gnd rf/dc ground pin. 2 rfin rf input pin. dc block required. 3 n /c no internal connection. provide grounded pcb land pads for mounting integrity. 4 v byp control pin for bypass mode . the lna is automatically turned off when the bypass mode is activated. refer to truth table on pg 2. 5 v sd control pin to disable the lna. refer to truth table on pg. 2. 7 rfout rf output pin. dc block required. 8 v dd supply voltage pin. external choke and bypass capacitors needed. backside paddle rf/dc gnd rf/dc ground. follow recommended via pattern and ensure good solder attach for best thermal and electrical performance. ? b a c k s i d e p a d d l e - r f / d c g n d p i n 1 r e f e r e n c e m a r k 8 7 6 5 1 2 3 4 v d d r f o u t g n d v s d g n d r f i n n / c v b y p r o g e r s 4 0 0 3 c r = 3 . 5 t y p . 1 o z . c u b o t t o m l a y e r f r 4 f r 4 1 o z . c u t o p l a y e r 1 o z . c u i n n e r l a y e r 1 o z . c u i n n e r l a y e r 0 . 0 6 2 " 0 . 0 0 6 " f i n i s h e d b o a r d t h i c k n e s s 0 . 0 0 8 " 0 . 0 0 8 "
qpl9096 ultra low - noise, bypass lna d ata sheet ju ly 5 , 201 7 | subject to change without notice 9 of 10 www.qorvo.com mechanical information package marking and dimensions n otes : 1. all dimensions are in millimeters. angles are in degrees. 2. except where noted, this part outline conforms to jedec standard mo - 220, issue e (variation vggc) for thermally enhanced plastic very thin fine pitch quad flat no lead package (qfn). 3. dimension and tolerance formats conform to asme y14.4m - 1994. 4. the terminal #1 identifier and terminal numbering conform to jesd 95 - 1 spp - 012. pcb mounting pattern n otes : 1. all dimensions are in millimeters. angles are in degrees. 2. use 1 oz. copper minimum for top and bottom layer metal. 3. vias are required under the backside paddle of this device for proper rf/dc grounding and thermal dissipation. we recommend a 0.35mm (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10). 4. ensure good packag e backside paddle solder attach for reliable operation and best electrical performance. 9 096 trace code ?
qpl9096 ultra low - noise, bypass lna d ata sheet ju ly 5 , 201 7 | subject to change without notice 10 of 10 www.qorvo.com rohs compliance this part is compliant with 2011/65/eu rohs directive (restrictions on the use of certain hazardous substances in electrical and electronic equipment) as amended by directive 2015/863/eu. this product also has the following attributes: ? lead free ? halogen free (chlorine, bromine) ? antimony free ? tbbp - a (c 15 h 12 br 4 0 2 ) free ? pfos free ? svhc free handling precautions parameter rating standard caution! esd - sensitive device esd? C ?human body model (hbm) class 1b esda?/?jedec js - 00 1 - 20 14 esd? C ?charged device model ( cd m) class c3 esda / jedec js - 002 - 2014 msl? C ?moisture sensitivity level level 1 ipc/jedec j - std - 020 solderability compatible with lead - free (260c max. reflow temp.) soldering process. solder profiles available upon request. contact plating: nipdau important notice the information contained herein is believed to be reliable; however, qorvo makes no warranties regarding the information con tained herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. all informatio n contained herein is subject to change without notice. customers should obtain and verify the latest relevant information before placing orders for qorvo products. the information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anythin g described by such information. this information does not constitute a warranty with respect to t he products described herein, and qorvo hereby disclaims any and all warranties with respect to such products whether express or implied by law, course of dealing, course of performance, usage of trade or otherwise, including the implied warranties of merc hantability and fitness for a particular purpose. without limiting the generality of the foregoing, qorvo products are not warranted or authorized for use as critical componen ts in medical, life - saving, or life - sustaining applications, or other application s where a failure would reasonably be expected to cause severe personal injury or death. copyright 2016 ? qorvo, inc. | qorvo is a registered trademark of qorvo, inc. contact information for the latest specifications, additional product information, worldwide sales and distribution locations : web: www.qorvo.com tel: 1 - 844 - 890 - 8163 email: customer.support@qorvo.com for technical questions and application information: email: appsupport@qorvo.com p b ?
|
