 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 5000w power supply with single output RST-5000 series ! "# # $%&'#( # ) *# )'#(+ !! , , , ! , - , . . ! ! / 0 ! , /1 2 3 / 3 3 !4 . .5 3 . ! ,, / 3 / ,67688 / 4 / # # $%&'#( # ) *#)'#( ? 9 3:8! ; !! %$< 8 .. ! 63 3 ,, . 3 = "#>$+ 9 ,67688 , 4 , : ? 63 63 3 63 , 8 ! bauar sicherheit egel ge ma t gepruft od be www. id 2000000000 tuv.com wac g os @ # , a )& $@ $ =$$ ; @# "=b+ "=b+ ,, # =% c c c c c c !?ba-7d-&%$ -2?-7= = =) 8 , , , , a , 9 ! 8 - 3 file name:RST-5000-spec 2016-10-27 63 "=)(#&()@(+ 6 , specification 5000w single output power supply RST-5000 series file name:RST-5000-spec 2016-10-27 model dc voltage rated current current range rated power output voltage adj. range line regulation load regulation setup, rise time hold up time (typ.) voltage range frequency range efficiency (typ.) input inrush current (typ.) leakage current over temperature working temp. working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing overload over voltage ac current (typ.) 2200ms, 80ms at full load 20ms / 230vac at 75% load 14ms / 230vac at full load 3 3-wire / 196 ~ 305vac or 3 4-wire / y 340 ~ 530vac ? 47 ~ 63hz 15a/230vac( ) 9a/400vac( / y) 3 3-wire / 3 4-wire ? 75a/230vac( ) 50a/400vac( / y) 3 3-wire / 3 4-wire ? <3.5ma / 305vac(y 530vac) 100 ~ 112% rated output power user adjustable continuous constant current limiting or constant current limiting with delay shutdown after 5 seconds, re-power on to recover 30 ~ 33.6v 60 ~ 67.2v 45 ~ 50.4v protection type : shut down o/p voltage, re-power on to recover -30 ~ +70 (refer to "derating curve") 20 ~ 90% rh non-condensing -40 ~ +85 , 10 ~ 95% rh 0.03%/ (0 ~ 50 ) 10 ~ 500hz, 2g 10min./1cycle, 60min. each along x, y, z axes 44.1k hrs min. telcordia sr-332 (bellcore) ; 34.6k hrs min. mil-hdbk-217f (25 ) 460*211*83.5mm (l*w*h) 10kg; 1pcs/10.1kg/1.15cuft 89% 91% 90% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 1.0% 1.0% 1.0% 150mvp-p 23.5 ~ 28.8v 200mvp-p 200mvp-p 47 ~ 57.6v 35 ~ 43.2v 24v 200a 0 ~ 200a 4800w 48v 36v 105a 138a 0 ~ 105a 0 ~ 138a 5040w 4968w RST-5000-24 RST-5000-48 RST-5000-36 $ , 76 , , =#("*)(+ / = ! ,. , = e , =2;f!. . $=g , $ !e )1! # ? / ) 3 / hi ., ,3/ . . 0 ! , . ! 5 , -2 .4., ,,c ,, , $,,! 0 ! 5 ,, . ! , , -2 3 1= #& 8 ! , -2 / ! h-2d !, i" 3 . ? , ,+ & . ! 3 3 :(3 ,,! , 3 3 3 3 d !! :(3 3/ j 3 3 power factor (typ.) 0.95/230vac(400vac) at full load safety standards ul60950-1, tuv en60950-1 approved ripple & noise (max.) note.2 voltage tolerance note.3 withstand voltage note.4 isolation resistance note.4 i/p-o/p:3kvac i/p-fg:2kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms / 500vdc / 25 / 70% rh environment safety & function emc (note 5) protection shut down o/p voltage, recovers automatically after temperature goes down parameter parameter esd radiated eft / burst surge conducted magnetic field voltage dips and interruptions conducted radiated harmonic current voltage flicker en55024 , en61204-3, en61000-6-2 standard standard en55022 (cispr22) / en55011 (cispr11) en55022 (cispr22) / en55011 (cispr11) en61000-3-2 en61000-3-3 en61000-4-2 en61000-4-3 en61000-4-4 en61000-4-5 en61000-4-6 en61000-4-8 en61000-4-11 test level / note test level / note level 3, 8kv air ; level 2, 4kv contact level 3 level 3 level 3 level 4 >95% dip 0.5 periods, 30% dip 25 periods, >95% interruptions 250 periods class a class a ----- ----- emc immunity emc emission alarm signal output remote on-off control auxiliary power(aux) please refer to the function manual. ac fail, dc ok, fan fail, otp. please refer to the function manual. 12v@0.1a(only for remote on-off control) remote sense compensate voltage drop on the load wiring up to 0.3v. please refer to the function manual. current sharing up to 20000w or (3+1) units. please refer to the function manual. output voltage programmable can be adjusted via built-in potentiometer adjustment of output voltage is allowable to between 20 ~ 120% of nominal output voltage. please refer to the function manual. adjustment of constant current level is allowable to between 20 ~ 100% of rated current. please refer to the function manual. constant current level programmable level 4, 4kv/line-earth ; level 3, 2kv/line-line 75 77 79 81 83 85 87 89 91 93 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 400v(y) 230v( ? ) pfc fosc : 70khz pwm fosc : 100khz o.v.p. fg i/p -v -s cs pv +v +s rectifiers & filter switching circuit power control pfc control & rectifiers pfc filter emi detection circuit o.t.p. current limit pc dc-ok remote on/off isolator & relay ac-fail fan-fail otp aux power (+12v/0.1a) rectifiers aux & filter power fan load (%) 20 40 60 50 80 100 100 90 80 70 60 50 load (%) -30010203040506070 196 210 220 230 240 250 260 270 280 290 305 (horizontal) 3 ? ambient temperature ( ) input voltage (v) 60hz 340 360 380 400 420 440 460 480 500 515 530 3y 5000w single output power supply RST-5000 series file name:RST-5000-spec 2016-10-27 derating curve static characteristics block diagram 91.15%/230vac ( ) 91.25%/400vac(y) efficiency (%) load model input 24v 4800w 4968w 5040w 200a 138a 105a 196~305vac 340~530vac 36v 48v efficiency vs load (48v model) 5000w single output power supply RST-5000 series file name:RST-5000-spec 2016-10-27 fig 1.1 ac power connection fig 1.2 3 3-wire / 230vac 230v 230v t RST-5000 s r fg l1 n1 l2 n2 l3 n3 3 4-wire / y 400vac t n s r RST-5000 fg l1 n1 l2 n2 l3 n3 230v 400v function manual fig 1.1 1.remote sense the remote sense function compensates the voltage drop on the cable, between the power supply and the load, up to 0.3v. if the remote sense function is not required,+s and +v of the output terminal, as well as -s and -v, need to be connected to be free from noise and interference. (+s and +v of the output terminal, -s and -v are connected as factory default setting) load -v +v sense lines should be twisted in pairs to minimize noise pick-up. +v cn313 cn314 cn315 -v pin5 -s pin3 +s dip sw note : RST-5000 can also be operated by 1 2 wire 196~305vac input. please refer to the connection diagram below. - operating with 1 2 wire may lead to certain characteristics different from the specification, such as the larger ripple and noise . should there be any - issues, please contact mean well. 230v l RST-5000 n fg l1 n1 l2 n2 l3 n3 fig 1.3 fig 2.2 nominal vout v 12345 6 20 40 60 80 100 120 external voltage (vdc) output voltage (%) non-linear 5000w single output power supply RST-5000 series file name:RST-5000-spec 2016-10-27 2.voltage adjustment (a)have the dip switch position-3 set as (a)have the dip switch position-3 set as (b)output voltage can be trimmed by svr. (b)the output voltage can be trimmed to 20~120% of the nominal voltage by applying external voltage between and on cn992 or cn993. pv+ pv- (1)by potentiometer (svr) (2)by output voltage programming* on off 123 on off 123 +s and +v, as well as -s and -v, need to be connected as factory default setting fig 2.1 load -v +v +v cn313 cn314 cn315 -v dip sw pin6 pv+ pin4 pv- external voltage (dc) cn313 dip switch svr *: or, pv/remote voltage programming / remote adjust / margin programming / dynamic voltage trim. fig 3.2 5000w single output power supply RST-5000 series file name:RST-5000-spec 2016-10-27 fig 3.1 load -v +v +v cn313 cn314 cn315 -v dip sw pin9 pc+ pin7 pc- external voltage (dc) 3.current adjustment (a)have the dip switch position-2 set as (b)output current is set default value. (1)default overload protection(olp) value (2)by constant current level programming** (a)have the dip switch position-2 set as on off 123 on off 123 (b)the constant current level can be trimmed to 20~100% of the rated current by applying external voltage between and on cn992 or cn993. pc+ pc- rated current v 12345 20 40 60 80 100 external voltage (vdc) constant current level (%) non-linear cn313 **: or, pc/remote current programming / dynamic current trim. +s and +v, as well as -s and -v, need to be connected as factory default setting 5000w single output power supply RST-5000 series file name:RST-5000-spec 2016-10-27 4.select overload protection (olp) mode (1)continuous constant current mode (2)delay shutdown mode have the dip switch position-1 set as ,and RST-5000 will work in continuous constant current mode when the out put is overloaded and have the dip switch position-1 set as ,and RST-5000 will shut down after 5 seconds of constant current operati on, when the output is the output voltage is greater than 50% of the rated output voltage. overloaded or short-circuited. on off 123 on off 123 5.remote on-off control the power supply can be turned on-off by using the "remote on-off" function. power supply off between ( ) and 12v-aux( ) remote on-off cn313 or cn314 pin10 cn315 pin1 output status power supply on table 5.1 fig 5.1 +v cn313 cn314 cn315 -v dip sw pin1 12v-aux pin3 gnd-aux pin10 rc+ pin8 rc- 6.alarm signal output there are 4 alarm signals on cn315, and each signal can select two types of output circuit. (1)relay contact output {otp1, otp1-gnd) ; (dc-ok1, dc-ok1-gnd) ; (ac-fail1-gnd, ac-fail1) ; (fan-fail1-gnd, fan-fail1)} (2)open collector output {dc-ok2-gnd, dc-ok2) ; (ac-fail2-gnd, ac-fail2) ; (otp2, otp2-gnd) ; (fan-fail2, fan-fail2-gnd)} normally open contact. "short" when the alarm arises. relay contact rating(maximum) is 30v/1a resistive. an external voltage source is required for this function that is shown in fig 6.2. these signals are isolated from output. the ma ximum sink current is 10ma and the maximum external voltage is 20v (there is a built-in 24v zener diode in inner circuitry). fig 6.1 r v switch open (open) switch close (short) cn313 cn315 fig 6.2 dc-ok2 gnd-aux 12v-aux RST-5000 dc-ok2-gnd ac-fail2 otp2 fan-fail2 ac-fail2-gnd otp2-gnd fan-fail2-gnd 10k x4pcs application circuit 7.current sharing 5000w single output power supply RST-5000 series file name:RST-5000-spec 2016-10-27 +v +v +v +v cn313 cn313 cn313 cn313 cn314 cn314 cn314 cn314 cn315 cn315 cn315 cn315 -v -v -v -v dip sw dip sw dip sw dip sw load -v +v -s +s +s,-s and cs+, cs- and rc+, rc- are connected mutually in parallel. when the remote sense function is used in parallel operation, the sensing wire must be connected only to the master unit. wires of the remote sense function should be kept at least 30 cm from input wires. RST-5000 has the built-in active current sharing function and can be connected in parallel, up to 4 units, to provide higher ou tput power as exhibited below : the voltage difference among each output should be minimized that less than 0.2v is required. the total output current must not exceed the value determined by the following equation. maximum output current at parallel operation=(the rated current per unit)x(number of unit)x0.9 when the total output current is less than 5% of the total rated current, or say (5% of rated current per unit) (number of unit) the current shared among units may not be fully balanced. mechanical specification case no. 223a unit:mm + + cn315 cn314 cn313 dip-sw led1 led1 led2 led2 svr svr 1 2 3 -v +v on 13 10 65 4 3 21 tb1 211 18max. 4-m4 l=5mm 29.9 45.5 120 399 86 4 3 5 7 10 9 86 42 1 3 5 7 10 9 86 42 1 3 5 7 10 9 12 11 14 13 16 15 18 17 20 19 cn315 cn314 cn313 2 1 air flow direction 4-m4 l=5mm 38 29.9 22.7 22.7 26 83.5 38 38 399 460 4-m4 l=5mm 29.9 screw "a? 399 5000w single output power supply RST-5000 series file name:RST-5000-spec 2016-10-27 10 2 1 9 mounting instruction hole no. recommended screw size max. penetration depth l recommended mounting torque 1 5mm m4 control pin no. assignment : hrs df11-10dp-2ds or equivalent () cn313,cn314 cn313 and cn314 are connected internally. mating housing terminal hrs df11-10ds or equivalent hrs df11-**sc or equivalent 7~1 kgf-cm 0 mounting screw mounting surface chassis of RST-5000 l 1 1 1 1 1 1 1 1 1 pin no. function description 1 3 4 7 8 2 6 9 10 cs- +s pv- pc- rc- cs+ pv+ pc+ rc+ current sharing signal. when units are connected in parallel, the cs pins of the units should be connected to allow current bal ance between units. positive sensing for remote sense. connection for output voltage . programming connection for output current programming. the output can be turned on-off in association with rc+ and rc-. 5-s negative sensing for remote sense. 5000w single output power supply RST-5000 series file name:RST-5000-spec 2016-10-27 led green (led1) red (led2) led on when output voltage is ok description led on when any protection occurs led status indicators ac input terminal pin no. assignment (tb1) dip switch position assignment(dip-sw): please refer to the function manual. pin no. pin no. 14 36 25 assignment assignment diagram mx a imum mounting torque 18kgf-cm ac/n1 ac/l3 ac/l1 ac/n2 ac/l2 ac/n3 20 2 1 19 control pin no. assignment : hrs df11-20dp-2ds or equivalent () cn315 mating housing terminal hrs df11-20ds or equivalent hrs df11-**sc or equivalent installation manual please refer to : http://www.meanwell.com/manual.html pin no. function 12v-aux dc-ok2-gnd dc-ok2 gnd-aux description 1 3 6 2 14 17 18 11 15 12 4 16 19 20 5 7 +v(signal) ac-fail2 ac-fail2-gnd -v(signal) otp2 otp2-gnd fan-fail2 fan-fail2-gnd auxiliary voltage output, 11.4~12.6v, referenced to pin 3(gnd-aux). the maximum load current is 0.1a. this output is not controlled by the "remote on/off" function. auxiliary voltage output gnd. the signal return is isolated from the output terminals (+v & -v). positive output voltage. for local sense only ; it cannot be connected directly to the load. negative output voltage. for local sense only ; it cannot be connected directly to the load. alarm signal of ac fail. open collector signal. low when the psu input voltage is too low. the maximum sink current is 10ma and the maximum external voltage is 20v. alarm signal of dc-ok. open collector signal. low when the psu turns on. the maximum sink current is 10ma and the maximum external voltage is 20v. alarm signal of dc-ok. normally open contact. "short" when the psu turns on. relay contact rating(maximum) is 30v/1a resistive. alarm signal of ac-fail. normally open contact. "short" when the psu input voltage is too low. relay contact rating(maximum) is 30v/1a resistive. alarm signal of fan fail. normally open contact. "short" when the internal fan fails. relay contact rating(maximum) is 30v/1a resistive. alarm signal of otp. open collector signal. low when the psu over temperature protection occurs. the maximum sink current is 10ma and the maximum external voltage is 20v. alarm signal of otp. normally open contact. "short" when the psu over temperature protection occurs. relay contact rating(maximum) is 30v/1a resistive. alarm signal of fan fail. open collector signal. low when the internal fan fails. the maximum sink current is 10ma and the maximum external voltage is 20v. 9 13 10 otp1 otp1-gnd dc-ok1 dc-ok1-gnd ac-fail1-gnd ac-fail1 fan-fail1 fan-fail1-gnd 8 pin no. 1 3 2 assignment diagram output current programming (pc) output voltage programming (pv) overload protection (olp) on off 123 dip-sw pin2:pc dip-sw pin3:pv |
Price & Availability of RST-5000
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |