phone [408] 946-1968 ? fax [408] 946-1960 ? hirel. sales@skyworksinc.com ? www.skyworksinc.com 202302b ? isolink proprietary information ? products and pro duct information are subject to ch ange without notice ? june 22, 2017 1 data sheet OLH6000/6001: high-speed schmitt trigger hermetic optocouplers features ? performance guaranteed over C55 c to +125 c ambient temperature range ? guaranteed minimum common mode rejection (cmr) transient immunity >1000 v/s @ 300 v cm ? microprocessor-compatible drive ? on/off threshold hysteresis ? fast switching: t r , t f = 10 ns typical description the OLH6000/6001 has an led and integrated high-speed detector that are mounted and coupled in a hermetic 8-pin side brazed dual inline package (dip), which provides 1500 v dc electrical isolation between the input and output. the light from the led is collected by the photo-diode in the integrated detector. the integrated detector incorporates a schmitt trigger, which provides hysteresis for noise immunity and pulse shaping and an open collector output. typical propagation delay of this product is 170 ns. the cmr transient immunity is greater than 1000 v/s at 300 v cm . the olh6001 is a 100 percent screened version of the OLH6000. c athode 3 a node 2 202302-001 g nd 5 v cc 8 v o 6 figure 1. OLH6000/6001 block diagram figure 1 shows the OLH6000/6001 functional block diagram. table 1 provides the OLH6000/6001 absolute maximum ratings. table 2 provides the OLH6000/6001 electrical specifications. figures 2 and 3 illustrate the OLH6000/6001 typical performance characteristics. figure 4 shows the OLH6000/6001 switching test circuit. figure 5 provides the OLH6000/6001 package dimensions. downloaded from: http:///
data sheet ? OLH6000/6001: high-speed schmitt trigger hermetic optocouplers phone [408] 946-1968 ? fax [408] 946-1960 ? hirel. sales@skyworksinc.com ? www.skyworksinc.com 2 june 22, 2017 ? isolink proprietary inform ation ? products and pro duct information are subject to change without notice ? 202302b table 1. OLH6000/6001 absolute maximum ratings 1 parameter symbol minimum maximum units coupled input to output isolation voltage 2 v dc C1500 +1500 v storage temperature range t stg C65 +150 ?c operating temperature range t a C55 +125 ?c mounting temperature range (3 minutes maximum) +240 ?c total power dissipation p d +300 mw input diode average input current i dd 20 ma reverse voltage v r 5 v power dissipation p d 40 mw output detector peak output current 40 ma supply voltage v cc 18 v output voltage v out 18 v 1 exposure to maximum rating conditions for extended periods may reduc e device reliability. there is no damage to the device with only one parameter set at the limit and all other parameters set at or below their nominal value. exceeding any of the limit s listed here may result in permanent damage to the device. 2 measured between pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together. t a =25 c and duration = 1 s. caution : although this device is designed to be as robust as possible, electrostatic discharge (esd) can damage this device. this devi ce must be protected at all times from esd. static charges may eas ily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. industry-standard esd precautions should be used at all times. downloaded from: http:///
data sheet ? OLH6000/6001: high-speed schmitt trigger hermetic optocouplers phone [408] 946-1968 ? fax [408] 946-1960 ? hirel. sales@skyworksinc.com ? www.skyworksinc.com 202302b ? isolink proprietary information ? products and pro duct information are subject to ch ange without notice ? june 22, 2017 3 table 2. OLH6000/6001 electrical specifications 1 (t a = C55 ? c to +125 ? c, unless otherwise noted) parameter symbol test condition minimum typical maximum units threshold current, on i f ( on ) v cc = 18 v, i ol = 10 ma 5 ma hysteresis ratio i f ( off ) i f ( on ) v cc = 18 v, i ol = 10 ma 0.8 low level output voltage v ol v cc = 18 v, i ol = 10 ma, i f = 5 ma 0.15 0.5 v high level output current i oh v cc = v o =18 v, i f = 0 ma 0 250 a supply current: high level low level i cc h i ccl v cc = 18 v, i f = 0 ma v cc = 18 v, i f = 5 ma 9.0 9.5 15.0 16.0 ma ma input forward voltage v f i f = 5 ma 1.55 2.0 v input reverse current i r v r = 3 v 10 a input to output leakag e current (note 2) i i _ o r h 50%, t a = 25 c, v i _ o = 1500 v dc 1 a propagation delay time: high to low fall time high to low rise time t phl t f t plh t r i f = 5 ma, v cc = 18 v, r l = 2 k i f = 5 ma, v cc = 18 v, r l = 2 k i f = 5 ma, v cc = 18 v, r l = 2 k i f = 5 ma, v cc = 18 v, r l = 2 k 150 10 250 10 300 500 ns ns ns ns common mode transient immunity: logic high logic low cm h cm l v cm = 300 v peak, r l = 2 k, v cc = 18 v, i f = 0 ma, t a = 25 c i f = 5 ma, t a = 25 c 1000 1000 >10,000 >10,000 v/s v/s 1 performance is guaranteed only under the conditions listed in the above table. 2 measured between pins 1, 2, 3, and 4 shor ted together, and pins 5, 6, 7, and 8 shorted together. ta = 25 c and duration = 1 s. downloaded from: http:///
data sheet ? OLH6000/6001: high-speed schmitt trigger hermetic optocouplers phone [408] 946-1968 ? fax [408] 946-1960 ? hirel. sales@skyworksinc.com ? www.skyworksinc.com 4 june 22, 2017 ? isolink proprietary inform ation ? products and pro duct information are subject to change without notice ? 202302b typical performance characteristics ambient temper a ture ( c ) 0 +25 +50 +75 +100 +125 C50 C25 C75 +150 forw a rd volt a ge (v) 2.22.0 1.4 1.2 1.81. 6 i f = 5 ma 202302-002 figure 2. forward voltage vs temperature ambient temper a ture ( c ) 0 +25 +50 +75 +100 +125 C50 C25 C75 +150 propagation delay (ns) 400300 200 100 0 t phl t plh v cc = 18 v r l = 2 k i f = 5 ma 202302-003 figure 3. propagation delay vs temperature pul s e g enerator z 0 = 50 t r = 5 n s 50 i f monitor i f s hield +18 v r l v 0 202302-004 0.1 f t phl t plh input i f v out 1.5 v i f = 5 ma 50% figure 4. OLH6000/6001 switching test circuit downloaded from: http:///
data sheet ? OLH6000/6001: high-speed schmitt trigger hermetic optocouplers phone [408] 946-1968 ? fax [408] 946-1960 ? hirel. sales@skyworksinc.com ? www.skyworksinc.com 202302b ? isolink proprietary information ? products and pro duct information are subject to ch ange without notice ? june 22, 2017 5 202302-005 0.3 9 0 0.005 87 6 5 1234 0.020 min. 0.150 max. 0.010 0.002 0.100 0.010 0.018 0.002 olhxxx xxyy s 0.320 max. 0.300 typ. 0.125 min. figure 5. OLH6000/6001 package dimensions downloaded from: http:///
data sheet ? OLH6000/6001: high-speed schmitt trigger hermetic optocouplers phone [408] 946-1968 ? fax [408] 946-1960 ? hirel. sales@skyworksinc.com ? www.skyworksinc.com 6 june 22, 2017 ? isolink proprietary inform ation ? products and pro duct information are subject to change without notice ? 202302b ordering information model name manufacturing part number OLH6000/6001: high-speed schmitt trigge r hermetic optocouplers OLH6000/6001 copyright ? 2012, 2017 isolink, inc. all rights reserved. information in this document is provided in connection with isolink, inc. (isolink), a wholly-owned subsid iary of skyworks so lutions, inc. these materials, including the information contained herein, are provided by isolink as a service to its customers and may be used for informational purposes only by the customer. isolink assumes no responsibility fo r errors or omissions in these materials or the information contained herein. isolink may change its documentation, products, se rvices, specifications or prod uct descriptions at any time, wi thout notice. isolink makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. no license, whether express, implied, by es toppel or otherwise, is granted to any in tellectual property rights by this document . isolink assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of isolink products, in formation or materials, except as may be provided in isolink terms and conditions of sale. the materials, products and information are pr ovided as is without warranty of any kind, whether express, implied, statutory, or otherwise, including fitness for a particular purpose or use, merchantability, performance, qualit y or non-infringement of any intellectual property right; all su ch warranties are hereby expressly disclaimed. isolink does not warrant the accuracy or completeness of the information, text, graphics or other items contained w ithin these materials. isolink shall not be liable for any damages, including but not limited to any special, indirect, incidental, statutory, or consequential dama ges, including without limitation, lost revenues or lost profits that may result from the use of the materials or informati on, whether or not the recipient of material s has been advised of the possibility of such damage. isolink products are not intended for use in medical, lifesaving or life-sustaining app lications, or other equipment in which t he failure of the isolink products co uld lead to personal injury, death, physical or environmental damage. isolink customers using or selling isolink products for use in such applications do so at the ir own risk and agree to fully indemnify isolink for any damages resulting from such improper use or sale. customers are responsible for their products and applications using isolink products, which ma y deviate from published specific ations as a result of design defects, errors, or operation of products outside of published parameters or design sp ecifications. customers shou ld include design and operating safeguards to minimize these and other risks. isolink assumes no liability for applications assistance, customer product design, or dama ge to any equipment resulting from the use of isolink products outside of stated pu blished specifications or parameters. isolink is a trademark of isolink inc. in the united states and other countries. skywor ks and the skyworks symbol are trademark s or registered trademarks of skywor ks solutions, inc., in the united states and other countries. third-party bra nds and names are for identification purpose s only, and are the property of their re spective owners. downloaded from: http:///
|
